Search Documents

By R. Singh, C. Gong, J. Chaudhry

"Metalorganic chemical vapor deposition (MOCVD) is an ideal technique for the deposition of conducting and non-conducting oxide based thin film materials. In this paper we have presented a study of photo assisted MOCVD for the low temperature deposition of a number of oxide based advanced materials. We have used incoherent light sources as the source of optical and thermal energy in our MOCVD system. The vacuum ultraviolet (VUV) and ultraviolet (UV) photons can enhance the surface reaction of the absorbed molecules through the perturbation of the electronic state of binding between the absorbed molecules and the solid surface. Unlike plasma process, no surface damage is expected and high quality materials have been deposited. At a given substrate temperature, the performance of deposited film depends on the lamp configuration.INTRODUCTIONMetalorganic chemical vapor deposition (MOCVD) has become the standard manufacturing technique for the deposition of large area thin films of compound semiconductors. l.(.w-cost, high crystalline quality, atomically clean and sharp interfaces, atomic layer epitaxy, high throughput rates and potential for direct writing are some attractive features of MOCVD. Due to a number of potential advantages mentioned above, MOCVD is considered as an ideal technique for the deposition of various electronic and optical materials for a wide variety of applications. Rapid isothermal processing based on incoherent radiation as the source of optical and thermal energy is emerging as the key low thermal budget (integral of processing time and temperature) processing technique for the fabrication of current and next generation of microelectronic and optoelectronic devices and circuits [1]. In this paper we have demonstrated that the design of the lamp assembly plays an important role in determining the properties of the materials deposited by RIP assisted MOCVD. We have studied the growth rates, structural properties and electrical properties of Y2O3/Si structure. At a given substrate temperature, best results are obtained for the lamp assembly that provides maximum number of VUV and UV photons."

Jan 1, 1994

By J. T. Crawford

A comprehensive strategic planning model has been developed for the phosphate strip mining and chemical operations at White Springs, Florida. The computerized model covers ore body modeling, production simulation and financial analysis. Several innovative features in the model include using NPV techniques in ore body block economics, adapting the floating cone method to a floating template for generating dragline mining units automatically, using interactive graphics for designing mining units, and a dragline move economics algorithm for automatic scheduling of mining unit assignments and moves. Simulation of chemical plant production uses linear programming and concentrate inventory levels control mine operating schedules.

Jan 1, 1997

By Per Svedensten

One of the most significant behaviour of a crushing plant is the constant variation in the process. The variation is caused by two major effects. The first and constantly changing is the rock material properties. During operation rock material with different strength and particle size distribution is fed to the plant which makes the performance of the equipment to vary. The second and more slowly changing variation is caused by wear on the processing equipment. These effects must be predicted in order to be able to optimise a crushing plant. This paper demonstrates how Monte Carlo simulation can be utilised to study and operate crush-ing plants. By introducing Monte Carlo simulation the varying process can be study and also optimised. To maintain the optimised process performance supervision is needed. This paper demonstrates how results from the Monte Carlo simulation can be utilised for process supervision. Charts for process measurements can for example be derived. These can then be used to guide decision making and understand how the variation and performance of the plant changes over time.

Jan 1, 2014

By D. K. Chibwe, P. Taskinen

"Typical operation of industrial Peirce-Smith converters (PSCs) used in copper smelting results in several common phenomena such as excessive splashing, slopping, tuyere blockage, and low converter campaign life due to high tuyere line refractory erosion. These phenomena give rise to an inefficient operation from both a process and an energy perspective.This investigation presents numerical and physical models of flow patterns, mixing, solid-liquid mass transfer, and slag-matte phase distribution in a slice model of an industrial PSC. For physical simulations, a 0.2-scale cold model was developed. Water, kerosene, air, and sintered benzoic acid compacts were used to simulate matte, slag, injected gas, and solid additions into the PSC. The two- and three-dimensional numerical simulations of the three-phase system were carried out using volume of fluid (VOF) and realizable k- e (RKE) turbulence models to account for the multiphase and turbulence nature of the flow respectively. These models were implemented using the commercial computational fluid dynamics numerical code FLUENT.Both numerical and physical simulations were able to predict, in agreement, the mixing and dispersion characteristics of the system in relation to various blowing conditions employed in the investigation. Measurement of mass transfer characteristics conclusively indicated that fluid flow in the PSC is stratified. Both blowing configuration and volume of slag in the converters were found to have significant effects on mixing propagation, wave formation, and splashing.The splashing and wave motion in these converters are known to cause losses of metal/matte and potential production time due to the requirement for intermittent cleaning of the converter mouth, resulting in reduced process throughput. To prevent these losses and hence to increase process efficiency, we propose a combined blowing configuration using top lance and lateral nozzles. The numerical simulations were conducted on combined, as well as lateral, blowing conditions. In comparison, the recent results of the combined blowing concept were found to be encouraging."

Jan 1, 2014

By S. H. Lau

Rapid 3D characterization of multiphase mineral particles in a variety of mineral processing applications is described, including: mineral liberation analysis, grain size, mineral exposure analysis, particle damage, and pore network structure for fluid flow simulation in heap leaching. While micro X-ray computed tomography systems (microCTs) have been used for many years, industrial adoption is limited due to a variety of reasons, including insufficient resolution, the general lack of imaging contrast to differentiate different mineral phases within a multiphase mineral particle and the lack of automated 3D mineral processing software. For example, resolution with industrial CTs and desktop microCT is of the order of tens of microns to a few microns at best, depending on specimen size and CT configuration. We describe a novel lab-based X-ray microscope, XRM, which overcomes these resolution and contrast limitations, notably as the industry is going towards finer grains and more complex ore bodies. Using lens-based optics and detectors (similar to its XRM counterpart in synchrotron beam lines), resolution of the lab based system is in the submicron range with contrast better than conventional microCTs. Hence, visualization, differentiation and segmentation of most mineral phases of interest to the industry are now feasible. Coupling these high resolution and high contrast tomography images with a suite of customized 3D segmentation algorithms and analysis software, applications in mineral liberation analysis for process control, particle damage assessment and other mineral processing applications can be achieved. This non invasive 3D technique which requires relatively little sample preparation is currently being considered for coal, industrial minerals, and base/precious metal ores, complementing existing microscopy techniques such as QEMSCAN and MLA for a variety of applications

Sep 1, 2012

"Introduction The first documentary record of coal nurung on Vancouver Island was that of the Hudson Bay Company operations in the Suquash area in 1836. Between 1836 and 1862, the Hudson Bay Company mined some 65,000 tonnes from this Suquash field and the Nanaimo coal fields discovered in 1851. However, systematic mining of coal did not take place until the Hudson Bay Company holdings were sold to the Vancouver Coal Company in 1861, and a rival company under Robert Dunsmuir was established in 1869. These two interests under various organizational names and jointly as the Canadian Collieries (D) Ltd. (1928) developed and exploited the coal seams of the Nanaimo and Comox Basins from 1852 to 1966. Because of the proximity of the coal outcrops to tidewater, the coal was readily marketed to ocean-going and coastal ships for fuel. However, during the turn of the century the main market was to meet the demand of the developing cities along the west coast of Canada and the United States for residential and commercial heating. Island-based copper smelters and brick factories, and the coming of the railroads motivated by steam engines increased the demand. This economic success of the industry continued until 1922 when a peak production of over 1,750,000 tonnes was reached. Following 1922 labour unrest in the industry, which affected the certainty of supply, and the availability of alternatives in the form of California petroleum and mainland coal combined to cause a rapid and steady decline in the demand for Island coal. In spite of post-and pre-wartime prosperities the trend could not be reversed. Serious coal mining phased out in the Nanaimo area in 1939 and in the Comox area in 1967. puring the 114 years in which the industry flourished over 75 million tonnes of coal were mined from more than 30 mines and a minimum of ten new mining communities were established on Vancouver Island."

Jan 1, 1985

By James Westfield

This publication covers the work of the Division of Coal Mine Inspection, Bureau of Mines, as performed under provisions of the Federal Coal Mine Safety Act. It presents background information and data since 1952 when the Act became effective and includes up-to-date statistics for the calendar year 1962. During that year, approximately 9,704 coal mines were active in the United States, and the Bureau made 12,810 regular inspections. BACKGROUND The Federal coal-mine inspection program was established to carry out the provisions in Public Law 49, 77th Congress, (H. R. 2082) approved May 7, 1941. This act has since been amended as Title I, Advisory Powers Relating to Health and Safety Conditions in Mines, under Public Law 552, 82d Congress, approved July 16, 1952, which also included Title 11, Prevention of Major Disasters in Mines. Public Law 552 is known as the Federal Coal Mine Safety Act.

Jan 1, 1963

By E Widzyk-Capehart

The conventional ammonium nitrate fuel oil (ANFO) loader utilises a pneumatic system to control the flow of ANFO (via rotary actuator/ball valve) and air (via an auxiliary air valve). This system, though relatively simple and reliable, has several drawbacks with respect to ease of control and level of automation. In this paper, a radio frequency (RF) remote control for explosives charging is discussed. The system design incorporates electric solenoid valves to control the rotary actuator and the auxiliary air valve. All operations associated with explosives charging are selectable at the remote and are completed according to a modifiable time sequence. This allows the following charging sequence to be reduced to a single momentary application of the remote:removal of water from the hole prior to charging with ANFO; charging of the hole for a preset but adjustable period of time; and removal of the remaining ANFO from the ANFO hose. A specially developed remote switch allows the operator to maintain two-handed control of the ANFO hose whilst achieving full control of the charge-up process. Failsafe electronic architecture is incorporated into the systemÆs design to increase safety to the highest level. Should the RF remote control fail, a wired remote is included in the system to allow for the charging process to continue, albeit at a reduced level of control. The application of the RF remote control system in an underground explosives charging operation minimises and/or eliminates many problems associated with the use of the conventional charging system. These include: the wet-hole problem, trip and entanglement hazards, air embolism and the two-man loader control requirement. The developed remote control unit proved to be effective at removing water from wet holes leading to increased face advance per drilling operation. It proved to be economically feasible, allowed for an increase in systemÆs dependability and safety factor and for a truly one-man operation which resulted in reduced manpower.

Jan 1, 1999

By W. S. Dyer

Introduction In northern Ontario, refractory clay is found on four rivers of the James Bay watershed: the Abitibi, the Mattagami, the Missinaibi, and the Moose. The clay all belongs to the same geological formation ( the Mattagami of Lower Cretaceous age) , and occurs within a structural depression or 'basin', the boundaries of which have never been defined but which appears to cover at least 1,500 square miles of territory. The recently constructed James Bay extension of the Temiskaming and Northern Ontario railway crosses the northeast end of the basin at the Onakawana lignite field, which by rail is 126 miles north of Cochrane, 605 miles north of Toronto, and 60 miles southwest of Moose Factory. Smoky Falls, the northern terminus of the railway owned by the Spruce Falls Power & Paper Company, Limited, is 7 miles south of one other point in the basin, i.e., the outcrops of refractory clay, sand, and kaolin at the foot of Long rapids on the Mattagami river. Smoky Falls is 50 miles north of Kapuskasing. In a very early report(l) , Dr. Robert Bell, of the Geological Survey of Canada, described '"light coloured marl in horizontal beds" from the Missinaibi river, and noted that the lignite also occurring in the river was probably :associated with the marls. This was undoubtedly the Cretaceous refractory day. Other early writers noted the occurrence of fire-clays, but it was not until Joseph Keele(2), of the Geological Survey, visited thee region in 1919 and studied the clays that their real significance was known.

Jan 1, 1933

By K. Whiting

In October 1993, the first two of a series of full scale passive biological treatment cells were constructed to treat mine drainage from the Burleigh Mine (located approximately 48 km west of Denver, Colorado in the Clear Creek/Central City Superfund Site). The two cells are each 19-21 m long, 10.7 m wide and 1.2 m deep. Each cell contains approximately 216 cubic meters of substrate (composted manure) and is designed to treat 60 L/min of mine flow. One cell is designed as an upflow reactor and the other cell is designed as a downflow reactor. The differences in flow hydraulics and treatment efficiencies will be tested in these two cell for approximately nine months before the remaining cells are built to treat all the discharge. The substrate material was selected based on a series of bench scale tests. During the tests, the amount of metals removed was determined. The design flow rate was based on a sulfide generation rate of 400 nanomoles of sulfide generated per cubic centimeter of substrate per day. Metal removal results for the first three months of operation of the two cells will be presented and compared to results of bench and pilot studies at other sites.

Jan 1, 1994

By J. J. Taute, S. J. Archer

"BASF Mining Solutions has developed a new-generation copper solvent extraction reagent that offers significant benefits over standard extractants currently available to the industry. As the name suggests, the new hightemperature (HT) extractant can be used at a higher operating temperature, but also exhibits significantly lower degradation rates, greater copper-toiron selectivity, and is totally nitration-proof compared with the standard extractants. Pilot-plant trials have also shown that lower aqueous-inorganic entrainment can be achieved. This paper investigates the technoeconomic benefit of using the HT extractant as an alternative to the standard extractant in a high-temperature application. The results of the technical evaluation showed that the use of the HT extractant reduces the extractant addition requirements and bleed volume from copper electrowinning; this smaller bleed requirement further reduces acid and limestone consumption, leading to a reduction in valuable metal losses. The results of the economic evaluation showed that the use of the HT extractant represents significant cost savings over that of the standard extractant. IntroductionCurrent solvent extraction (SX) reagents employed for the extraction of copper from typical pregnant leach solutions (PLS) at ambient conditions function well with minimal long-term effects on the extractant’s performance (Taute et al., 2015). This performance, however, deteriorates at elevated temperatures due to the degradation of the reagent’s hydroxyoximes. The degradation mechanism, acid-catalysed hydrolysis of the oxime, is accelerated by high temperature. This has a knock-on effect where the increase in degradation products increases the organic viscosity, leading to increased entrainment, crud formation, and ultimately to an increase in SX reagent consumption (Bender, Emmerich, and Nisbett, 2013).SX reagents also show an increase in the co-extraction of iron as the ferric concentration in the PLS increases. Co-extracted iron is transferred to electrowinning (EW) during stripping of the loaded organic and can adversely affect EW current efficiency. Iron in the EW circuit is typically managed by bleeding the electrolyte; however, this can lead to excessive consumption of EW reagents such as acid, cobalt, and mist-eliminating surfactants. The electrolyte bleed can also affect upstream consumption of reagents, such as lime, due to the high acid concentration recycled to leach."

Nov 1, 2018

By M. L. Lissberger

entirely suitable for certain uses and even possess advantages over present solders at high temperatures, but they are certainly not suitable for all uses. However, it is conceivable that their use in many places will effect a material conservation of tin. It will probably be wiser to use cadmium in solders where good results have been obtained than in brass where this element will be a source of possible trouble. F. F. Colcord,* New York, N. Y.-—The cadmium-lead solder has a higher conductivity than the lead-tin alloy, which ought to make it advantageous in the manufacture of electrical machinery. In the case of solder for tin-can work, one of the high officials of the American Can Co. said that he fully intended to .give it a good trial, and I do not believe they are going to reach hasty conclusions and run the risk of poisoning the public. Solder, Its Use and Abuse Milton L. LissbeRgeR,† New York, N. Y.—Solder is a mechanical mixture of tin and lead, a fact which is susceptible of very simple demonstration. A bar of solder of a grade even as low as 30 per cent. tin and 70 per cent. lead, passed through a buffing machine, will show a surface practically identical with that of a bar of second-quality or reclaimed tin. The buffings, on chemical analysis, will prove to be almost pure lead. According to the best practice, solder is made in the following manner. Virgin pig lead is first melted, and when it is thoroughly liquefied, virgin pig tin is added, together with a small amount of flux; the latter is for the purpose of bringing to the surface the so-called "liver," consisting of impurities that may have remained in either the lead or the tin as a result of incomplete refining. The combined material, when completely liquid, is thoroughly stirred for some hours, and is then cast into small pigs. Just before casting, and continuously during this operation, the molten metal yields dross, consisting largely of the oxides of lead and tin; this should be carefully skimmed off. After the pigs have cooled, they are taken to a smaller kettle, re-melted, and cast into the desired shape for use; or if wires, ribbons, etc., are to be made, the solder is cast into slugs suitable for extrusion and rolling. During this second operation, the skimming of dross should be even more carefully done than at first. Hand mixing has proved to be the only reliable method for the production of the best quality of solder, irrespective of its percentages of lead and tin. The best quality of solder is not necessarily that which contains the highest percentage of tin, but rather is that composition which performs best on the required piece of work. In order to produce

Jan 1, 1919

By H. H. Stoek

(Wilkes-Barre Meeting, June, 1911.) THE origin of the Mine-Rescue Service of the State of Illinois can be traced to two distinct sources, the work of the Rescue Station at Urbana and the Cherry disaster. During the early part of the year 1909, the Technologic Branch of the U. S. Geological Survey, now the Bureau of Mines, in connection with the Illinois Geological Survey and the College of Engineering of the University of Illinois, established at the University of Illinois, in Urbana, a branch rescue-station to supplement the work of the Pittsburg station of the Geological Survey. As a result of the work of training at the station in Urbana by R. Y. Williams, mining engineer, and James Webb, foreman of the Bureau of Mines, and the use of the helmets at several mine-accidents in the State of Illinois, . the people of the State were somewhat familiar with oxygen-helmets when the Cherry disaster occurred, in November, 1910. The oxygen-helmets were successfully used in connection with that disaster, and upon the recommendation of the Illinois Mining Investigation Commission, the Legislature of the State, assembled in special session during the winter of 1910, passed a bill appropriating $75,000 for the erection and maintenance of three rescue-stations, stipulating that they should be located in the northern, central, and southern parts of the State. The Act also provided that the stations should be in charge of a Commission of seven, two representing the United Mine Workers of Illinois, two the mine-operators, one the Federal Bureau of Mines, one the State mine-inspectors, and one the Department of Mining Engineering of the University of Illinois. This Commission was called together by the Governor of the State, Aug. 2, 1910, and since that time three stations have been located, built, and equipped: at La Salle for the northern

Dec 1, 1911

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Respirable crystalline silica (RCS) found in dust generated by various mining processes is an important occupational hazard in the underground coal-mining industry. Exposure can lead to disabling and incurable diseases, including coal workers’ pneumoconiosis (CWP), silicosis and lung cancer [1,2]. Clusters of rapidly progressive CWP have been observed in the Appalachian regions of eastern Kentucky and southwestern Virginia, and recent cases have been generally more severe and showing more rapid progression. CWP is approximately four times as common among long-tenured underground coal miners in central Appalachia than long-tenured underground miners in the rest of the United States, and 20.6 percent of long-tenured underground miners in central Appalachia were suffering from the disease as of 2017.

By Sataev IS, Malinovskaja ND, Otrozdenova LA, Knodov NV, Maximov II, Kuznetzou OK

The technology of flotation recovery of silver from the residue of a zinc plant is described. The peculiarity of this technology is a preliminary pulp conditioning in sodium chloride solution in the presence of aluminum metal under high temperature. In this process the silver is converted to the metallic phase and then floated with the usual sulphydryl collectors. A variant using a combined technology is also described, in which before flotation is performed about 50 per cent of silver is leached. The total silver recovery with the combined technology comes up to 90 - 94 per cent.

Jan 1, 1993

By C Woodfull, S Munroe

Geological uncertainty is reduced by improved understanding of the relationship between regional-scale geological basement features (structure, composition, depth) and known local structural risk (such as recognised structural hazards at the mine). Coal mining and exploration entities can be more efficient and effective in managing geological risk at a range of scales. A more efficient and effective performance in forward interpreting and managing geological risk will result in a more efficient and effective exploration and also incremental or even significant mining cost improvements. In order to improve the understanding of basement features, a new 4D regional structural/basin framework for the Sydney Basin and the eastern part of the Gunnedah Basin has been constructed to provide primarily coal exploration and mining with a more integrated geological framework for ongoing subregional to mine-scale geological risk based studies. The model has been developed from a range of available regional geophysical and geological datasets, of variable detail and reliability, which have been brought together to generate a more robust structural and tectonic model than could be generated with any one single dataset. An initial regional structural model for the Sydney Basin was constructed in 2003 and an update to the model was released in 2005 (SRK Consulting, 2003; 2005). The development and ongoing refinement of the model was undertaken with financial and data support from a number of coal mining industry, gas exploration and government organisations. Prior to, and following the development of the regional structural/basin model and associated Information Base, a number of more area-specific studies have been completed, using the æbasement upÆ assessment approach. The methodology for developing comprehensive structural models, from the basement up, is outlined. The approach can be applied at a country-wide, regional or lease area scale. Case examples of where this approach has been used as an effective and efficient method in improving geological certainty and as a predictive tool to help manage geological risk are also presented.

Jan 1, 2006

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Nucleation and growth of copper on 316L stainless steel from synthetic acidified copper sulfate was studied in the absence and presence of chloride ions and/or organic additives (HydroStar® 4208, DXG®-F7, Cyquest® N-900) using a potentiostatic technique. The current-time data obtained at 0.16V vs. SHE was analyzed using nucleation and growth models. Scanning electron microscope (SEM) images of deposits produced at 300 A m-2 show that the addition of 20 mg/L chloride ions increased the size and reduced the number of copper nuclei. Potentiostatic current-time data from the electrolyte without organic additives indicate progressive nucleation with two-dimensional (2-D) growth under diffusion control. SEM images obtained confirmed progressive nucleation with 2-D growth. 20 mg/L Cl- and 2.5 mg/L organic additives did not change the nucleation and growth mechanism, however the additives increased the number and reduced the size of copper nuclei leading to more uniform coverage of the stainless steel substrate.INTRODUCTION Electrowinning of copper is an important process in the manufacture of high purity copper metal. It is approximated that 20% of the world’s refined copper is produced from acidified copper sulfate solutions by electrowinning (Schlesinger, Sole, and Davenport, 2011). In many plants, copper is electrodeposited on AISI 316L stainless steel substrates for a period of 6-7 days, after which the copper is stripped from the blanks. Even though the deposition time for a commercial copper electrowinning circuit is around one week, it is critically important to control the nucleation, growth, and nature of the initial deposit (Sun and O'Keefe, 1992). Deposit morphology and structure are influenced by the real current density at the electrode surface. The real current density across the cathode surface is made uniform by proper design of the electrowinning cell and electrodes and careful operational practice. Even with good design and control, some current maldistribution occurs. The outcome of severe current maldistribution is poor deposits that affect product quality and/or increase energy consumption. To combat current maldistribution and create a larger operating window in terms of current density, temperature, and copper concentration, small amounts of organic smoothing agents (traditionally guar products) are added to copper electrowinning electrolytes. Moreover, these additives inhibit the growth of copper dendrites, which leads to improved deposit quality by producing bright, smooth, and dense cathodes."

Jan 1, 2015

By Philip W. Holland

The U.S. Bureau of Mines has designed and built an inexpensive, weatherproof, temperature-controlled cabinet to provide temporary housing for analytical instrumentation. The cabinet consists of an inverted Styrofoam ice chest, an electric fan for air circulation, and a proportional temperature controller equipped with a thermistor sensor and a light bulb as the heater. The cabinet provides a constant-temperature environment for a moisture analyzer and a strip chart recorder when outside temperatures range from -SO to 21° c.

Jan 1, 1993

By Leonard B. Gulbransen, John R. Lewis, W. Martin Fassell, J. Hugh Hamilton

A simple reproducible method was developed for determining the ignition temperatures of magnesium and magnesium alloys and by this method magnesium and over 100 magnesium alloys were measured. The ignition temperature of magnesium was determined in O2-SO2, O2-N2 mixtures and in O2 from 0.166 to 10 atm pressure. The ignition temperature of magnesium is generally lowered by alloying and increased by an increase in oxygen pressure. WITH the expanded use of magnesium alloys in industry, ignition temperatures are of considerable importance, especially in heat treating and for service at elevated temperatures. Magnesium alloys exhibit a relatively slow linear oxidation rate up to temperatures near the melting point.' At some critical temperature the rate of oxidation becomes extremely rapid. This high rate of oxidation is accompanied by the emission of light and additional characteristics suggesting a flame. The literature concerning the ignition temperatures of magnesium and magnesium alloys is relatively incomplete and the values reported by various authors are not in agreement. The most probable reasons for this are: 1—The absence of a suitable definition of ignition, and 2—the need of a standardized method of determining the ignition temperatures of inflammable metals and alloys. The exact date of the discovery of the fact that magnesium will ignite and burn is unknown. It is likely that H. Davey encountered this property of the metal during its preparation in 1808. The first reference in the literature specifically on ignition of magnesium is by Lenze, Metz, and Rubens.' They investigated the inflammability of certain magnesium alloys. Brown3-' reported that magnesium ribbon will ignite in air at 507 °C by what was called the rising temperature method. Hartman, Nagy, and Brown" reported that magnesium powder ignites from 475" to 560°C depending on particle size. According to Guise, Mars, and Wilson prolonged heating in air at 427°C of common casting magnesium alloy causes it to ignite. Samples of magnesium alloys were placed directly in the flame of a torch by Carapella and Shaw.' These investigators obtained some evidence of melting prior to ignition. For commercial magnesium, they reported an ignition temperature of 650°C. Their values varied from 450" to 800°C for magnesium alloys. Willmore and Peterson" studied the effect of air velocity, humidity, rate of heating, and foreign metal contact on the ignition temperature of magnesium. They conclude that melting is not a prerequisite for ignition and that the conditions which influence ignition are complex and difficult to analyze. The only quantitative theoretical treatment of the ignition temperatures of magnesium and magnesium

Jan 1, 1952

By M. J. Voigt, R. A. Govender, A. Mainza, L. Bbosa

"Mineral texture is a critical factor which controls ore variability and is an important attribute in geometallurgy. In relation to downstream processes, it affects the fracture pattern during breakage, where rock strength is inherently a function of mineral texture. Because of the subjective nature of mineral texture, it has not been easy to quantify, especially in the context of a measurement suitable for use in geometallurgical programmes. The aim of this paper is to present the first steps in developing a 3D mineral texture quantification method for drill core and to assess its sensitivity to differences in rock strength using a case study. The methodology includes classifying the textural information using the 3D grey level co-occurrence matrices (GLCM) and X-ray computed tomography (XCT) coupled method. Rock strength tests were performed using the split Hopkinson pressure bar (SHPB). The case study investigates a heterogeneous polymetallic sulphide deposit and a homogeneous shale subdivided into three ’mineral textural types’. The variability is largely captured by the GLCM matrices, and preliminary trends can be observed where the shale is finer grained and has a higher yield strength in comparison with the coarser grained polymetallic sulphide ore. IntroductionModern mining requires the exploitation of lower grade and more complex, heterogeneous orebodies to address the growing industry demands. Historically, processing plants were designed and built based on average ore characteristics and therefore are relatively inflexible when facing the full spectrum of ore variability in heterogeneous orebodies (Lamberg, 2011; Lotter, 2011; Schouwstra et al., 2013). The practice of geometallurgy represents an opportunity to manage ore variability in the mining industry (Powell 2013; Baum, 2014; Yildirim et al., 2014; Nguyen, 2013). It focuses on quantifying the relationships between ore characteristics and their downstream mining and processing responses, often starting with small-scale laboratory testing. The purpose of geometallurgy is linked to maximizing the net present value (NPV) of an orebody by minimizing technical and operational risk – where ‘ore variability’ is considered one of the most significant technical risks."

Apr 1, 2019