Search Documents

By John J. Dran

The elaborate analytical techniques for risk analysis used by the large mining companies in conjunction with the valuation of mineral reserve sites are totally inappropriate for the small miner. The small miner does not possess the financial and technical resources which are available to the large companies for such risk analysis. Even if these resources were available to him, the relatively small size of his investment would not justify a huge expenditure for risk analysis. What is required by the small miner is an improvement over the single point estimates provided by the valuation techniques that he currently uses. Such improvement should provide an indication of the extent to which the true value (known only after the fact) might differ from his estimated value of the mineral reserve site. In addition, a rough indication of the chance of occurrence of various differences between the true and estimated values would be helpful to him. These improvements must be obtained at low cost to be useful to the small miner. Such improvements would have to be based on a simple system requiring very few additional estimates by the miner. The small miner is not accustomed to dealing with sophisticated risk analysis techniques. Hence, any complex, time-consuming approach would be doomed to disuse or possible misuse. A simple, uncomplicated approach requiring a minimum of additional estimates by the miner can be based on a system devised by Frederick S. Hillier Although Hillier's method can be applied to various mineral reserve valuation methods used by the small miner, this note is specifically oriented to the discounted cash flow model. The basic discounted cash flow (DCF) approach provides a single point estimate of value and introduces the concept of risk (i.e. the possibility that the annual cash flows may differ from their estimated values and thus lead to an incorrect investment value) through the use of a risk-adjusted discount rate. This approach simply lowers the present value estimate with increases in the discount rate (i.e. increases in the risk assessment). The single point estimate still remains. Although the lower value estimate makes it less likely that the risky investment will be deemed profitable and undertaken, it provides no indication of risk that is suitable for examination and analysis. In addition to the "best guess" estimate of annual net cash flows required in the DCF model, application of the Hillier risk analysis model requires that the miner

Jan 1, 1976

By Zsuzsanna Zborovszky

Study of different parameters (minimum discharge voltage, minimum discharge current, wire electrode diameter, speed of separation, electrode materials, overlap of the electrodes, etc.), their direct effect on the power going into the discharge, and their indirect effect on the possibility of obtaining ignition with an 8.31% methane-air mixture from a resistive circuit. Critical evaluation of the Cadmium disc breakflash (the presently internationally recommended test apparatus). Description of experimental setup and apparatus.

Jan 1, 1974

By M. K. G. Vermaak

Kimberlite weathering has been a topic of ongoing research within De Beers for many years. Using kimberlite weathering as an alternative to crushing has many advantages e.g. power and reducing diamond breakage. Weathering could also possibly be used in conjunction with crushing just to weaken the material and reduce power consumption. These forces have driven current research to investigate whether kimberlite weathering could be utilised for these reasons. Weathering in this context does not refer to weathering over long period of time but rather to disintegration of the material in aqeous media in relative short time periods. Previous published work discussed that the presence of smectite renders kimberlite weatherable and that the amount of smectite determines the rate of weathering (Morkel and Vermaak, 2006). The current work investigates whether cation ex-change or the adsorption of organic species in the smectite interlayer could influence the observed weathering behaviour. The results show that cation exchange does take place in the presence of cation species and that the weathering behaviour can be drastically improved with especially Cu2+ cations. Concentration and time effects of the weathering was also investigated. Weathering tests with organic species such as ethanol, methanol, edta, pentanol, butanol, acetic acid and oxalic acid was performed. The results show that organic species does improve weathering but under these testing conditions was not as effective as cations.

Jan 1, 2014

By N Steenkamp, L Furstenberg, W Cele, M Richter

Managing productivity and improving efficiency for a healthy return on capital employed have become key mining industry strategies under prevailing tough global market conditions. However, achieving this in a multisystem environment such as a mining operation can be daunting. The field of discrete event simulation offers some relief, giving engineering teams insight into multivariable systems and stochastic processes. It allows for integrated system thinking and domain expertise to be woven into project thinking fibre. Directed system optimisation and therefore improved efficiency becomes possible. Furthermore, capital discipline accrues from optimal upgrade investments. This paper illustrates the practical application of this approach by reviewing a typical case study for a direct shipping iron ore operation. Dynamic simulation was used to establish maximum processing plant capacity under varying material characteristics and identify capital-efficient upgrades for increasing production.The study started with descriptive statistical analysis of existing data. Discrete equipment and system capacities were defined, followed by static plant mass balance calculations to establish bottlenecks and overall static capacity. Equipment ‘uptime’ and ‘downtime’ analyses established system and overall plant availability and utilisation. From this information, a dynamic simulation model could then be developed and initially calibrated against actual plant performance to verify its robustness. Once confirmed to accurately represent existing plant dynamics, system capacity response to variable changes could be tested to ultimately determine maximum plant capacity. Additionally, plant optimisation was incorporated to arrive at optimal upgrade points. Maximum capacity and necessary upgrades were established as a function primarily of feed size distribution. Additionally, the interfacing effects of rehandling feed material to the final product grade and potentially to life-of-mine were established as important outcomes. The results of the study illustrate the value of using dynamic simulation models to realistically and cost-effectively increase throughput.CITATION:Cele, W, Furstenberg, L, Richter, M and Steenkamp, N, 2015. Capacity evaluation of iron ore processing facilities utilising dynamic simulations, in Proceedings Iron Ore 2015, pp 597–604 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By R. R. Webster, H. T. Clark

I. A. Sirel—I would like to ask Mr. Sims what would the preferred hot metal analysis be as far as manganese and silicon are concerned if you used specially made iron for this process instead of basic iron. C. E. Sims (authors' reply)—A preferred composition would contain somewhat less silicon than the basic pig iron used in these experiments. High silicon requires a large lime addition. Lime must be added in sufficient quantity to neutralize the silica formed and to leave an excess for dephosphorization. Manganese presents almost no problem in operation. It is almost completely oxidized and, in burning, develops considerable heat. The evidence indicates, however, that, in continuous commercial operation, there will be an excess of heat produced, and the bath will need to be cooled in some manner as by the addition of scrap or by utilizing the energy for the direct reduction of ore. There do not seem to be any serious limitations on composition of pig iron. One heat was made with an iron containing 2.27 pct silicon and the phosphorus finished at 0.007 pct. In another, the iron contained 0.45 pct phosphorus which was lowered to 0.019 pct. This indicates considerable leeway in composition. D. R. Loughrey—We are all very much interested in the recent discovery of very large deposits of iron ore both in Labrador and in Venezuela. I would like to ask Mr. Sims if the iron ore at either or both of these places is such that it would lend itself to the manufacture of iron suitable for use in the turbohearth. C. E. Sims-—According to my information, those ores are not essentially different from ores now used in this country for making basic pig. They should, therefore, be adaptable to this process. D. I. Brown—You have spoken about the leeway, or spread in analysis of the various irons you can use in the vessel. I would like to have you tell us, if you can, about the different kinds of steels which can be made in such a vessel. The turbohearth process, or it might more aptly be called pneumatic openhearth, is a little different from that used in most Bessemer shops and in the one in which I worked. If we had a blow in the air over 10 min, the boss was in the pulpit in a hurry

Jan 1, 1951

By George Munro

New Zealand is a small, almost pristinely pure country environmentally speaking. It is blessed with an abundance of clear waterways, lush green vegetation and fresh clean air. It is a country in which agriculture and forestry predominate, and mining developments have to be introduced prepared to answer in considerable detail the question "How will this proposal affect the New Zealand environment as we know it today". Those who make the legislation have the difficult problem of establishing standards at a level which will maintain as far as possible the status quo without unduly inhibiting the developments currently approaching the starting line. We have been fortunate in some sense in that since the demise of the early gold rush days by the 1920's, little mineralisation of a complex nature has been uncovered in New Zealand. Coal fields have been developed in the central North Island, and on the West Coast and Southland regions of the South Island. A ban on large scale open cast mines in the Coromandel area has restricted mining in that highly prospective area, although three large gold prospects have got underway elsewhere in the last three years. There is no other ore processing being undertaken at present. Some recent proposals involving lead, gold and silver in complex arseno­ sulphides have failed to get the necessary approvals and have been discarded. Our ore processing problems are therefore straightforward ones, and confine themselves to acid drainage, mercury handling and disposal, and cyanide.

Jan 1, 1991

By Bo Zhou

During secondary aluminum recovery, complex aluminum scraps are melted and refined often in a rotary melting furnace and the aluminum metal has to pass through a molten salt layer and melt down in a bottom aluminum bath. Previous experimental study and industrial observations have indicated that salt shell formation and re-melting on the metal solids in the early stage plays a critical role in the overall melting process of the scrap. In the present paper, mathematical models are developed to simulate the process of salt shell formation and its re melting, as well as aluminum melting in the molten melt. Influence of the salt layer properties, the residence time of the metal particles in the salt layer, the particle size, the temperature of bulk melt were investigated. Reasonable agreement with the measurement data was reached. The developed melting model will be used to construct a population balance model of the scrap melting behavior for a rotary melting furnace, taking into account the distributed characteristics of the scrap. Finally, an overall process model based on Computational Fluid Dynamics (CFD) for the rotary furnace will be constructed, coupling with the population balance model for the scrap melting.

Jan 1, 2003

By Francisco Geraldo Toledo Junior

Os aços inoxidáveis possuem características essenciais para um bom acabamento quando o que se busca é estética e boa resistência à oxidação. O acabamento polido é muito utilizado em utensílios domésticos, eletrodomésticos e ponteiras de escapamentos de veículos. Em muitos casos são expostos à elevação de temperatura sendo sujeitos à oxidação a quente que pode causar o amarelamento da superfície desses aços. Através de ensaios de oxidação a quente, potencial eletroquímico, microdureza e tensão residual via difração de raios-x foi possível perceber uma diferença entre os acabamentos brilhantes via laminador com cilindros polidos e acabamentos obtidos pelo polimento de rebolos de panos e pastas abrasivas. O ensaio de tensão residual mostrou qualitativamente que o aumento de dureza e o forte amarelamento ocorrido no material com acabamento polido pode ser em função de uma deformação elástica na superfície imposta durante o processo na linha de polimento automático.

Aug 16, 2017

By B. J. Steblay

Roof bolts are the primary means of supplemental support in coal mines and are widely used in other mines. Presently, post installation loads are measured infrequently on only about 10% of the bolts by using standard torque wrenches that limit accuracy to about ± 30%. Because mine roof bolts are long, slender, non-uniformly sized, roughly forged, placed in a difficult environment, and subject to severe bending on installation, researchers have been unable to use ultrasonic reflection techniques to measure strain. A complete measurement system has now been assembled by the US Bureau of Mines, Denver Research Center. Obstacles such as bolt preparation, transducer mounting, reliable reflection, and calibration have been dealt with. The seemingly simple concept of measuring the time of flight of an ultrasonic pulse to a reflector is actually complex due to the need to measure to 0.0025 mm (0.0001 in.) accuracy, the sensitivity of velocity to temperature, and stress, and the stability required to make measurements over several years.

Jan 1, 1986

By R. Thierbach, W. Kahnt, Oberthür. T., D. Eisenburger, V. Gundelach

ABSTRACT: The ground penetrating radar (GPR) method was used in a platinum mine in Zimbabwe by members of the Federal Institute for Geosciences and Mineral Resources (BGR). The measurements were carried out in boreholes and drifts. Electromagnetic re?ections from a fault that consistently trends parallel to the mineralization zone permitted the mapping of the economically minable parts of the deposit. An introduction is given to the geology of the studied area and the application of the GPR method. The electrical parametres of the rocks are measured in situ, the GPR measurements are displayed with radargrams, and the visible structures are explained in illustrations.

Jan 1, 2010

By Caio Moreira, Saulo De Rezende, Nelly Ruíz

The present project sought alternatives for this material through the Mining Lab Beginnings program, which was developed by Nexa in partnership with Escalab to find solutions for the company's highly complex challenges. Through the program, several solutions were evaluated, with additives for the construction market being the most prominent. Tests were conducted to confirm the efficiency of jarosite in the mixture that composes this material. With successful laboratory tests, the technology was tested on an industrial scale, where it also demonstrated its technical and economic viability. The project is now moving into the operational phase, demonstrating that circular economy is the best solution for disposed tailings.

Sep 29, 2023

By AIME AIME

MINERAL production of the United States is valued at over five billion dollars a year at present and the industry employs close to a million workmen, yet such maps as are available that might indicate the geographical distribution of this industry show only the location of coal and oil fields and of other mineral deposits. No recent map is available that shows this distribution in a quantitative way. The purpose of the maps and graphs here presented is twofold: (1) to give the mining engineer a clear conception of the relative value and the pattern of distribution of minerals in the United States; (2) to test the so-called block-pile (or grouped pillar) system of statistical mapping, which makes this presentation possible. (I discussed this method of mapping in an article which appeared in Economic Geology in 1939, Vol. 15, p. 185-188.)

Jan 1, 1941

By B. Grosso

The National Italian Regulation concerning environment protection imposes that industrial areas are provided with systems aimed at preventing the circulation of contaminated groundwater. These systems can be static or dynamic and operate basically by intercepting the contaminated flow. Their effectiveness, realization time and costs depend on the intervention type and on the features of the specific site. The selection of the best solution is complex and the results obtained by this selection may be affected by residual risks related to the uncertainty of the hydrogeological and geotechnical characterization of the site. With regard to the industrial area of Portovesme, located in the south of Sardinia, the paper presents the analysis of alternative interventions aimed at the protection of the groundwater. The attention is focused on the evaluation of their effectiveness, impact on environment and, finally, time and costs of construction.

Jan 1, 2008

By Jeffrey D. Oke

While significant progress in underground construction engineering has occurred in the past few decades, a number of fundamental deficiencies persist regarding the recognition, prediction, and mitigation of underground construction hazards associated with complex geological conditions in rock and soil works, such as tunnelling. Many of these shortcomings could be addressed by improving geomechanical models which, in turn, would provide more realistic frameworks for determining input parameters for design analysis. This would improve predictions of construction efficiency for tunnelling and the formulation of more accurate modelling techniques (2D, 3D and 4D) required to optimize the design of engineered rock structures. This research focuses primarily on the issues related to forepole temporary tunnel support within weak rock masses. This research attempts to determine how best to numerically model forepole support. The behaviour and mechanics of forepole support has not been quantified and/or optimized. As well, there is a lack of in-situ and/or laboratory forepole and weak rockmass interaction parameters available. In terms of numerical modelling, there is a lack of understanding of the use of proper interaction parameters associated with the forepole and the rockmass. The parametric study that has been conducted by the authors demonstrates the influence of each of the forepole-rockmass interaction parameters and their sensitivity. Introduction

Jun 1, 2012

By Joseph Yancik

El presente texto señala el método de evaluación que determine el sistema óptimo de los explosivos de una voladura. Los componentes básicos para una voladura óptima son: características de la roca, planificación de la mina, preparación, manipuleo, equipo de procesado y sistema de explosivos. Es preciso anotar que el punto óptimo de una voladura no está constituído por un grupo estático de condiciones. Si consideramos que los costos de perforación y disparo representan una parte significativa del costo total de la operación de minado, no es posible ignorar avances tecnológicos que ofrecen substanciales reducciones en el costo. Em este sentido, el sistema de potencia de campo, se plantea como el sistema adecuado para la predicción rendimiento de un explosivo a través de la determinación de su potencia, "in situ" bajo condiciones indicadas.

Jan 1, 1971

By Blair Burwell

This paper describing the method of mining a deposit of vanadium ore near Rifle, Colo., is one of a series of similar papers on metal-mining methods and costs being issued by the United States Bureau of Mines. This vanadium deposit probably is the largest yet found in North America. It is situated 12 miles northeast of Rifle, Colo. (see fig. 1), on the southern flank of tae White River plateau, and is at an altitude of 6,500 feet. Between 150 and 200 tons of ore are mined daily and trucked to the mill at Rifle. The product of the mill is fined vanadium oxide, which is shipped to the company's plaits at Columbiana, Ohio, and Niagara Falls, N. Y., for the electric manufacture of ferrovanadium. HISTORY The deposit was discovered about 1909 by men prospecting for carnotite. Its outcrop on the bola cliff of Rifle Canon had been known to stockmen for many years.

Jan 1, 1932

INTERNATIONAL ENGINEERING CONGRESS, 1915.. Announcement. In connection with the Panama-Pacific International Exposition which will be held in San Francisco in 1915, there will be an International Engineering Congress, in which engineers throughout the world will he invited to participate. The Congress is to be conducted under the auspices of the following five National Engineering Societies: American Society of Civil Engineers, American Institute of Mining Engineers, The American Society of Mechanical Engineers, American Institute of Electrical Engineers, and The Society of Naval Architects and Marine Engineers. These societies, acting in co-operation, have appointed a permanent Committee of Management, consisting of the Presidents and Secretaries of each of these Societies, and eighteen members resident, in San Francisco. Thus constituted, the personnel of the Committee 'is as follows:

Jan 9, 1913

By H. M. Howe

§ 24. Introduction.—This paper discusses the chief existing data as to the temperature, in iron-carbon alloys, of Ae3, the upper limit of the transformation range when in equilibrium, as distinguished from Ac3, the temperature at which the end of the transformation is noted in heating up, and from Ar3, that at which its beginning is noted in cooling down. The former is in fact carried above Ae3 and the latter below Ae3 by lag. I touch incidentally on the influence of manganese on Ae3 (§ 29, p. 614). The sections, tables, and illustrations are numbered consecutively with those in the accompanying papers by Howe and Levy on Determination of the Position of Ae3 in Carbon-Iron Alloys, and by Burgess, Crowe, and Rawdon on Thermal and Microscopical Examination of Professor Howe's Standard Commercial Steels, to which the present paper forms a sequel. § 25. The contradictoriness of our present evidence is shown by grouping it together in Fig. 14. For instance, both Goerens and Meyer (Series 2) and Meuthen (Series 12) used practically stationary temperature, and thus reduced the influence of lag very greatly; yet Ae3 for 0.32 carbon steel according to the former investigators is 894", but according to Meuthen it is at or below 770°, a discrepancy of 124" or more. In view of our ability to measure these high temperatures within a few degrees, the existence of such a discrepancy is as unwelcome as it seems needless. I attack the thankless task of bringing some order out of this chaos. In Part 11. (§§ 29 to 39) I consider the chief causes of error. In Part III. (§§ 40 to 48) I apply certain corrections to some of the existing data, review those data, weight them, and calculate a prob-

Jan 1, 1914

By Robert D. Schmidt

The US Bureau of Mines is cooperating with Cyprus Mineral Park Mining Co., Columbia University, and the US Geological Survey in investigating the feasibility of applying in situ leach mining methods to fracture-hosted, supergene copper sulfide (chalcocite) ores. This paper presents the initial findings of mineralogical, hydrogeological, and geochemical characterization studies conducted at the Mineral Park mine, located in the Wallapai mining district of northern Arizona. A design for in situ leaching is proposed that would minimize the need for blasting prior to leaching, and would enable economical development of deep reserves at the Mineral Park mine. The in situ leaching design would also reduce the potential for long term acid rock drainage.

Jan 1, 1995

By P. N. Anyalebechi

"The as-cast microstructure of two commercial-size ingots of aluminum alloy 3004 produced by the electromagnetic casting process was quantitatively characterized. This involved the quantitative determination of through-thickness and across-width variations in dendrite cell size, grain size, macrosegregation of alloying elements, interparticle spacing, and the types, volume fractions, and sizes of the constituent or second phase particles. More than ninety-five percent of the constituent phases in the ingots consisted of the A16(Mn,Fe) phase; the desirable a-Al 12(Fe,Mn)3Si phase was not detected in any of the ingots by Guinier X-ray diffraction analyses or electron probe X-ray microanalyses. A significant microstructural heterogeneity through the thickness and across the width of both ingots was observed. For example, macrosegregation, and the sizes of the constituent phase particles, dendrite cells, and grains increased concomitantly from edge to mid-width and from surface to center of the ingots. There was a -20% depletion (negative macrosegregation) of Mg and a +54-87% enrichment (positive macrosegregation) of Ti in the center of the ingots. With the exception of grain size, there was no significant microstructural difference between the two ingots examined. The causes and practical implications of the observed microstructural heterogeneity in the ingots are discussed.IntroductionThe first step in the fabrication of majority of wrought products of aluminum and its alloys is the casting of large ingots or billets of simple shapes (round or rectangular). The sizes of the ingots vary from 10 mm to 450 mm diameter or 25 mm to 780 mm thick. The quality of the finished products is established at the ingot casting stage. This is because the microstructural characteristics, such as secondary dendrite cell size or arm spacing, amount of alloying elements retained in solid solution, macrosegregation, and the characteristics of second phases, produced during casting cannot be reversed by subsequent processing. Up until twenty-five years ago, the effect of as-cast microstructure of large ingots on the structure and behavior of thin sheets (0.34 mm thick) during drawing and ironing processes was incorrectly assumed to be minimal or nonexistent. This was based on the erroneous notion that the thermal treatments and large reduction (>99.94%) and strain that the ingot undergoes during production of the sheets completely destroys the original ingot structure and its inherent heterogeneity. However, the effects of ingot structure can, a priori, be deduced from the observed effects of constituent phase particle size, type and volume fraction on recrystallization, development of texture during annealing and deformation, and earing. In fact, careful examination of the behavior of products produced from different size ingots or castings have shown that the original microstructure of the ingot has a direct impact on the properties and performance of the end products."

Jan 1, 2011