Search Documents

By W. R. Bacon

"IntroductionTHIS IS a brief discussion of certain regional and economic aspects of the Coast Range of British Columbia. Between Portland canal and the 60th parallel of latitude, only the eastern margin of the Range is in Canada. The solely British Columbia interval extends from Portland canal to Burrard inlet. Personal observations in various parts of this area form the basis for much of this paper.Regional GeologyGranitic RocksSome of the best, most continuous exposures in the Coast Range are found at sea level. Reconnaissance study of the coastline has shown that the Range is predominantly granitic in character, but there simplicity ends, for the term 'granitic' as applied to the Coast Range covers a variety of mineralogical compositions. Actual granite is quite uncommon, occurring mainly in irregular or dyke-like masses that do not achieve batholithic dimensions. It is commonly pinkish, relatively homogeneous, and exhibits few of the deformational features that are obvious in much of this plutonic complex.Most of the granitic rocks of the Range fall well within the compositional limits of quartz diorite and granodiorite. The problem of resolving the great mass of these rocks into smaller coherent units is in general a difficult one. As noted above, granitic rock of uniform composition and texture is found in restricted areas and can be outlined without much difficulty. One such body occurs on the southern shore of Nelson island."

Jan 1, 1955

By J. A. Sekhar

Solidification processing/casting is increasingly being adopted as the preferred manufacturing technique for the fabrication of net shaped complex geometry components. Modeling of solidification processes is important both for design purposes as well as for understanding the physics of morphological evolution of the solidification microstructure. A fundamental aspect of such modeling involves the precise understanding? of heat transfer through the two phase solid/liquid region. A scheme to do this will be presented where the nonlinearity of the fraction liquid with change in temperature can be incorporated into the numerical calculations. The importance of properly accounting for the non-linear mushy zone will be discussed. Typical processes like squeeze casting and electromagnetic stirring will be discussed to illustrate how precise modeling of the solid/liquid region can aid in the calculation of accurate heat transfer coefficients for these processes.

Jan 1, 1990

By George CW

Western Mining Corporation (W.M.C.)operate a 30 000 tpa nickel refinery at Kwinana, W.A. using the Sherritt Gordon Process. Following ammonia/air leaching of sulphideminerals and subsequent copper removal, nickel metal is produced as powder by hydrogen red-uction of the ammonium sulphate-rich solution. Batchwise reduction in pressure autoclaves is preceded by an oxidation/hydrolysis step to ensure nickel powder quality.The reduction process is energy intensive, requiring high temperatures and pressures. Present energy requirement is 24 GJ per tonne of nickel reduced. Of this, 95% represents steam and hydrogen consumption and 5% electric power. The design and operation of the red-uction circuit is reviewed, outlining the main areas of steam and hydrogen usage.

Jan 1, 1985

By Hasan Ali Taner, Vildan Onen

One of the problems in flotation is mechanical entrainment and the other is the presence of complex gangues (especially clay minerals). In the present study, it was aimed to determine the effects of clay types (kaolinite, illite, and montmorillonite) on mechanical entrainment parameters (total flotation recovery, real recovery, mechanical entrainment recovery, and water recovery). Effects of clay types and clay amount on chalcopyrite flotation were investigated by flotation experiments. Interaction mechanisms between the clay minerals and ore were characterized using SEM–EDS analyses. Experiments were carried out with and without a collector using the mixture of clay minerals and ore under certain experimental conditions. While the clay mineral most affecting the chalcopyrite grade was montmorillonite, the highest mechanical entrainment recovery and the lowest real recovery values were obtained in the presence of illite. While illite is stated as the least problematic clay mineral in the literature, it was determined that illite among three clay minerals used in this study caused significant mechanical entrainment. In contrast, it was determined that increasing the amount of kaolinite did not have a significant effect on mechanical entrainment. This study’s findings will guide in determining of clay minerals’ effect on gangue entrainment in flotation.

Dec 29, 2023

By W. B. Carter, A. T. Hunt, G. W. Book

"Combustion Chemical Vapor Deposition (CCVDSM ), an open air, flame assisted CVD process, is under development. The CCVD process produces non-line-of-sight, epitaxial deposition. Materials deposited include YBa2Cu3Ox' Y2BaCuOx, BaTiO3, Y2FesOI2, ZrO2, yttria stabilized ZrO2 (YSZ), partially (yttria) stabilized ZrO2 (PSZ), and amorphous silica. Two modifications of the CCVD process are being studied. Liquid fuel CCVD deposition, involves the combustion of an organic solvent that contains dissolved reagents carrying the desired coating cations. Gaseous fuel CCVD deposition uses a flammable gas as fuel. A non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol prior to its combustion. Substrates to be coated are held near the flames' ends.IntroductionThin films and coatings can be deposited using a wide variety of techniques including chemical vapor deposition (CVD). CVD is ""a materials synthesis process whereby constituents of the vapor phase react chemically near or on a substrate surface to form a solid product.""lIn conventional CVD processing, gases carrying coating constituents flow into a reaction vessel where deposition occurs onto a heated substrate. The deposition process is often conducted at reduced pressure. Both cold and hot wall reaction chambers are used. Heat can be provided by a resistance furnace, rf induction, or high-intensity radiation lamps. Plasma, microwave, photo, laser, RF, and electron-enhanced CVD processes have been developed. The necessity of using a reaction vessel limits the substrate size and affects coating economics. Although most CVD depositions are performed as batch processes, continuous deposition can be accomplished with the use of appropriate hardware.The chemical vapor deposition of thin, dense oxide films has been accomplished in the open atmosphere with a flame assisted process. The process is called combustion chemical vapor deposition (CCVDSM).2 Two modifications of the CCVD process have been developed. The liquid fuel CCVD process involves the combustion of an organic solvent in which reagents (containing the coating cations) are dissolved. The gaseous fuel CCVD process uses a flammable gas as fuel. In this modification, a non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol of small droplets prior to its combustion. Substrates to be coated are held near the flames' ends."

Jan 1, 1994

By Bibhu Mohanty, Sheng Huang

Accurate measure of fragment size distribution is a key objective in all blasting and crushing operations. Several generic distribution functions have been devised to describe the degree of fragmentation for the representative range of fragments from selected measurements. The application of four distribution functions, i.e. Rosin-Rammler, Swebrec, Grady and Gilvarry, in describing fragment size distribution of impact-induced fragmentation of a limestone rock has been investigated. A modified Hopkinson Pressure Bar experimental set-up is used to control both impact velocity and energy input into the target rock. The feed size in the sample holder is varied from 6.35mm to 15.88mm in three ranges and the impact velocity up to 14m/s. The size distribution in the product is determined by sieve analysis for a range of impacts. The experimental results are fitted to the four distribution functions to examine their relative accuracy and reliability.

Jan 1, 2016

By H. Dho

The role of sodium silicate in the anionic flotation of a Florida phosphate ore was investigated using laboratory continuous flotation tests, frothability tests and SEM observations. In the absence of sodium silicate, Ca++ promoted the unwanted activation of quartz by forming calcium bearing precipitates. The addition of sodium silicate enhanced the flotation efficiency through: (1) the removal of impurity minerals and calcium-bearing. precipitates from quartz surfaces by dispersion, (2) drier and more persistent froths stabilized by oily droplets containing calcium silicate precipitates, and (3) higher specific flotation rates of phosphate relative to quartz, leading to faster flotation rates and increased selectivity of separation.

Jan 1, 1990

By William J. McCaughey, Richard L. Barrett

FOR sixty years-in fact, ever since the inception of the basic steelmaking process -basic slags have been the subject of study by chemists, metallurgists and petrographers, with the purpose of providing a better understanding of the reactions between the slag and the metal during the refining process. The result of this work and of the researches of mineralogists and physical chemists into the chemistry of oxide systems is a considerable body of literature dealing not only with slags themselves but with equilibrium relationships in systems synthesized from pure components. Since any actual slag is a multicomponent system more complex than any yet worked out in the laboratory, a complete solution to the problem is still far away. The writers have recently published a paper1 which they believe sheds light on the role of the slag in the elimination of phosphorus and it is the purpose of the present paper to discuss the metallurgical applications of that work. Since the pioneer investigations on the constitution of basic slags carried on by Stead and Risdale, Carnot and Richards, Hilgenstock and others in the 1880's, a considerable body of literature on this subject has appeared. Many of the more important of these papers were summarized in the previous paper,' therefore they will not be reviewed here. PETROGRAPHIC STUDY The present writers have had occasion, over a period of years, to examine petrographically a great number of basic steel- making slags having a very wide range of chemical compositions and made under various conditions of operating practice. Although certain of these slags exhibit some unusual features, it is a remarkable fact that the great majority of mature slags show certain typical characteristics, which persist throughout the wide range of chemical compositions. The typical mature slag usually appears under the microscope to consist of two phases. The phase of primary crystallization is light colored and doubly refracting. If separated mechanically and subjected to chemical analysis, it is found to consist essentially of SiO2, CaO, and P2O5. Sometimes, although not usually, two such silicate-phosphate phases are found. The other conspicuous phase is dark in color and optically isotropic, and occurs as the interstitial material between the grains of the light colored phase. This dark colored interstitial phase when analyzed is found to consist essentially of FeO,Fe2O3, MnO, and MgO. In some slags high in iron oxide, particularly those from low-carbon heats, dicalcium ferrite is found. This phase is dark reddish brown in color and anisotropic.

Jan 1, 1944

By W. J. Schuster

Safety in coal mines depends largely upon adequate training of the foreman. Although management must provide modern and safe equipment and at all times keep mines in first class condition from a safety viewpoint, final results will be determined by the quality of supervision. HANNA COAL CO., Division of Pittsburgh Consolidation Coal Co., operates three large underground mines in eastern Ohio. The section of Pittsburgh No. 8 coal seam in which these mines are located varies in thickness from 52 to 64 in. It is immediately overlain by a stratum of shaly material 12 to 15 in. thick locally known as draw slate, which is structurally very weak and which disintegrates rapidly upon exposure to atmosphere. Immediately above the draw slate as it is normally found is a band of extremely high ash material 6 to 12 in. thick known as roof coal or rooster coal, and above this is a stratum of conglomerate material varying from 4 to 10 ft in depth. Overlying the conglomerate is a relatively thick stratum of limestone, the first stable material above the Pittsburgh coal seam in eastern Ohio. With the method of full-seam mining that has been adopted, draw slate is shot down, loaded with the coal, and removed in the preparation plants. The roof coal then becomes the permanent roof. The major problem in mining the No. 8 seam in eastern Ohio is control of the roof. Since the strata above the draw slate contains no material with a structure firm enough to provide self-support, the roof begins to sag in a relatively short time after the coal and draw slate have been removed. The problem thus becomes one of getting temporary safety posts under this roof as quickly as possible to prevent a break or separation from occurring either in the roof coal or in the conglomerate above it. Haulage System The Pittsburgh No. 8 seam in eastern Ohio is relatively level, with only minor local dips. Throughout the Hanna Coal Co. mines, entries are generally 12 ft wide. Rooms are driven on a 60" angle on 30-ft centers and are 22 ft wide. No attempt is made to extract the 8-ft pillars between. The entire length of main line haulage is gunited in one mine, and a major portion in another. Two of the mines have single-track main haulage roads with passways. The third, a new mine, is double-tracked, and the roof is supported by steel crossbars, 60 lb or heavier, spaced on 4-ft centers and lagged. In recent years timbering on main line and secondary haulage roads has been accomplished by one of two methods: 1—crossbars are supported on a small section of post set in a hitch hole in the rib, or 2—or a hole is drilled in the rib about 12 in. below the roof, of sufficient depth to fasten securely a short length of 40-lb rail, the bottom of the rail facing the roof, on which a short post is set directly under the crossbar. At present the hitch-hole timbering method is favored. At two of the mines the main line haulage locomotives are 26-ton, 8-wheel units. These locomotives are of the axleless type, each wheel being individually mounted on the frame. The motorman's compartment is encircled by 3-in. armor plate for the protection of the occupants. At the third underground mine conventional 15-ton locomotives are being used. However, these locomotives have been completely rebuilt in the company's shops. Equipment has been streamlined and quarters have been provided for two people, who are protected by heavy steel plate in much the same way described above. This modernization program has been completed on all secondary haulage locomotives at the three mines, and the company is well on the way to similar equipment of the 6-ton section locomotives. The following additional features have been included in their modernization: 1—additional support for the motors to prevent their falling to the middle of the track and derailing the locomotives should a break occur in the suspension bar support; 2—installation of additional bracing to prevent brake rigging from becoming displaced and causing derailments; 3—enclosure of all electric wiring in conduit or raceway; 4—provision of an enclosed compartment for the storage of re-railers, jacks, and other equipment, so that they need not be carried on the outside of the motor; and 5—redesign of the end of the locomotive opposite the operator's compartment to prevent anyone's mounting from that direction. It is interesting to note that some

Jan 1, 1955

By Carin Laubscher, Francis W. Petersen, Jaap P. Smit

Waste streams, such as acid mine drainage, are often characterised by low pH values and high concentrations of heavy metals, dissolved solids, calcium and sulphates. Although lime remediation effectively removes most of the heavy metals as hydroxides, it is less effective at lowering levels of sulphates. Various methods of removing sulphates from effluents exist, such as precipitation with lime, precipitation with barium salts, co-precipitation with calcium carbonate, reverse osmosis, and ion exchange. Mintek developed a chemical precipitation (SAVMIN) process to treat acid mine drainage, which entails the addition of lime to precipitate the metal hydroxides, and the subsequent formation (precipitation) of calcium sulphoaluminate or ettringite. The key to the viability of the new technology lies in the correct use, regeneration and recycling of Al(OH)3 used to precipitate the ettringite. The water produced by this process is suitable for disposal to watercourses or for agricultural, domestic or industrial consumption. No brines are produced as the salts are converted to solid hydroxides, gypsum and calcium carbonate. The technology has been tested on several different waters in pilot plant campaigns. Results obtained indicate that potable water can be produced (containing less than 200 mg/L sulphate and no heavy metals) as long as the monavalent ions (Na+, Cl-, etc.) are within limits.

Jan 1, 2003

By Z. Y. Ma, H. Y. Yang

The process of microwave-ultrasound assisted leaching of valuable metals from copper anode slime was proposed in this paper. Design of experiments has been used to study the effect of the main leaching parameters, such as microwave power, ultrasound power and reaction time. The central composite design (CCD) was used to predict the maximum leaching efficiency of copper, tellurium and selenium. The experimental data obtained were fitted to a second-order polynomial equation, and they also were analyzed by analysis of variance (ANOVA). The 3-D response surface plots and the contour plots were applied to determine the optimal conditions. The optimum conditions of microwave-ultrasound assisted leaching process were: microwave power 834W, ultrasonic power 638W and reaction time 403s. Under these conditions, the experimental leaching efficiency of copper, tellurium and selenium were 98.88±0.56% 98.96±0.78% and 98.57±0.67%, respectively, which agreed well with the predicted values.

Jan 1, 2014

By N. Tiner

IN an article on magnesium and its alloys, Gann and Winston1 stated that manganese has a limited solubility in the liquid state. W. Schmidt2 showed a diagram according to Joseph Ruhrmann indicating that the solubility of manganese in liquid magnesium falls from about 2.65 per cent at 790°C. to about 0.5 per cent at 695°C. The curve was extrapolated to show zero solubility at the melting point of pure magnesium (Fig. I): This work suggested that at the lowest manganese contents it was not possible to detect either a eutectic or the formation of a solid solution, so that manganese was stated to be present in the structure as large individual crystals. Two years after the presentation of these results, Gann3 brought evidence to show that some manganese is capable of dissolving to form a solid solution, any excess of manganese present then assuming chiefly the form of small blue-gray particles scattered throughout the primary magnesium crystals, occasionally in clusters but seldom at the boundaries. He presented micrographs of cast alloys containing o.1, 0.4 and 1.0 per cent manganese that show a small amount of coring around the individual particles due to solid solution, and indicate that the location of the manganese particles is closely associated with the original dendritic structure of the primary crystallization. He also pointed out that the amount of manganese that can be dissolved in magnesium depends on the amount of other alloying elements present, the effect of the second alloying element being to decrease the amount of manganese retained in the alloy. E. Schmid and G. Siebe14 have determined the solid solubility of manganese and its variation with temperature by means of precision X-ray diffraction measurements. They found that the solubility is 3.4 per cent at 645°C and decreases to practically zero at 200°C. It is apparent that the X-ray diffraction measurements of Schmid and Siebel are not in agreement with the results of Ruhrmann as presented by Schmidt. This disagreement, and also the lack of data on magnesium-aluminum-manganese and magnesium-zinc-manganese systems, led the author to the present investigation, to determine accurately the liquid solubility of manganese and its variation with temperature. EXPERIMENTAL METHOD The experimental method for making solubility determinations consists of saturating the molten magnesium or the alloys with manganese at various temperatures and analyzing the dip samples taken from these melts. Melting is carried out in a cylindrical steel pot heated by an electric resistance furnace. The pot had a metallic outside coating to protect the steel against oxidation, and a graphite inside lining to prevent the contamination of the melt by prolonged contact with iron. The inside diameter of the pot was 4 in. and the depth 12 inches.

Jan 1, 1945

By Robert J. Hundhausen

This report describes Bureau of Mines investigations of a low-grade scheelite-bearing granodiorite intrusive situated on Henderson Creek, Granite County, Mont. The intrusive is in a narrow, V-shaped valley at the head of extensive placer workings. Since May 1943 the H. & R. Mines Co. of Portland, Oreg., has recovered scheelite sand and gold from the placer workings. A modified Yuba, 4?cubic foot bucket dredge was used in the operation. By February 1947 this operation had recovered and marketed over 215,000 pounds of scheelite concentrates containing 63 percent WO3. The scheelite in the placer was found to be derived principally from erosion of the granodiorite intrusive. The intrusive is one of a series of four similar, dikelike masses of granodiorite whose outcrops are aligned along a 10-mile zone of weakness trending N. 60° E. The intrusive has a triangular outcrop exposed over an area of 57 acres. Trenching and sampling by the Bureau of Mines demonstrated that scheelite is sparsely distributed throughout the granodiorite. This work delimited the outcrop of the intrusive and indicated a large submarginal reserve of low-grade tungsten mineralization. The deposit is ideally suited for exploitation by large-scale, open-pit mining operations; it would be easily available in a national emergency. Additional exploration would be necessary, however, before large-scale production plans could be made efficiently or accurately.

Jan 1, 1949

By S. M. Moore

Each year more than 400 coal miners are injured (fatally and nonfatally) by rock falling from between or around roof supports. Many of these injuries can be prevented by the installation of roof screen. However, many coal mines are reluctant to use roof screen because of the added cost. The goal of this study was to determine the potential savings in workers' compensation (W C) premiums that can be achieved due to a reduction in rock fall injuries after roof screening. The WC rate-setting methods utilized by Illinois and Kentucky were investigated in this study. Using data obtained from the Mine Safety and Health Administration, national and state WC bodies and individual insurance companies (e.g., average cost per injury, loss cost rate, number of injuries per year, number of injuries preventable each year with roof screening), baseline mines (representing two mine sizes: 67 and 150 employees) were constructed with realistic ranges for estimates of injuries and WC premium costs. Using each state's actual WC rate-setting formulas, a sensitivity analysis was conducted to determine the total savings in WC costs after a three-year period. Annual savings in WC premiums ranged from $41,000 to $326,000 for the 67-person mine, and $96,000 to $843,000 for the 150-person mine. An economic analysis of the cost of a roof screening program at a 67-person mine was also conducted. The annual cost of a roof screening program here was estimated at $240,000. At this mine, the reduction in WC premiums alone could pay for the entire screening program.

Jan 1, 2010

By F Sinaga, E Widijanto

PT Freeport IndonesiaÆs Deep Ore Zone (DOZ) mine is the new underground block caving mine within the East Ertsberg Skarn System (EESS) which started production in mid-2000. The DOZ will produce 25 000 tpd using mechanised block cave mining method and will be the fourth underground mine opened within the EESS deposit. A review of the DOZ extraction bolting design was conducted in November 2000. The aim of this review was to re-evaluate the effectiveness of the current design in relation to bolt length and spacing and to challenge some questions about the technical background of the design. For instance, the influence of the rock condition on the design. To review this bolting design, several books and papers are reviewed and several experienced people have been contacted to give their opinion. The methodology used for this review is:reviewing the technical background of current design; collecting ideas and alternatives; collecting data from books and personal communication and conducting analysis; and conclusion and proposed design.

Jan 1, 2002

By M. M. Fine

Development of a process for winning copper from pelletized chalcocite concentrate without matte smelting and converting is underway at the Twin Cities Metallurgy Research Center, Bureau of Mines. The new route from concentrate to metal includes 2-stage fluid-bed treatment; pelletized concentrate (33 percent Cu, 7 percent S) is first desulfurized (to about 0.5 percent S) in an oxidizing atmosphere, and in the second stage the calcine is metallized by reduction with hydrogen. Thereafter, the reduced product plus 10 percent CaO is routed to a smelting furnace to separate metallic copper from the gangue. Recovery and the Cu content of the product at this point are in the 97-98 percent range. The metal must be refined to remove sulfur and iron to make wirebar copper. An important feature of the process is the pelletizing of the fine concentrate into mini-pellets prior to fluid-bed treatment, which has permitted shorter reaction time, decreased dusting, and facilitated subsequent processing.

Jan 1, 1970

By Erik Bengtsson

Phenol was discovered in coal tar by Runge (1)1/ in 1834 and was isolated (2) in 1841 as pure phenol by distilling the tar, extracting with caustic soda, acidifying the extract, and fractionating the tar acids. Later, o-cresol was isolated (3) through careful fractional distillation of the tar-acid mixture. The m-and p-cresols distilled within a boiling range of about 1.50 c. and had to be separated by other means. Raschig (4) fractionated the tar-acid mixture to obtain pure o-cresol, sulfonated the mixture of m-and p-cresols, and treated the cresol-sulfonic acids with superheated steam at 1200 to 1300 c. to hydrolyze the m-cresol sulfonic acid, the p-isomer was not affected at that temperature. He also attempted to make use of the different crystallizabilities of the m-and p-cresol sulfonic acids (5). When treated with sodium bisulfate and sodium pyro-sulfate at 100° to 110° C. or with sulfuric acid (90/0) at 20° C., only the m-cresol was sulfonated (6). Hoffman-La Roche (7) treated the meta-para mixture with concentrated sulfuric acid at 40° to 100° C., when m-cresol and part of the p-cresol was sulfonated, and precipitated the m-cresol sulfonic add by diluting with water. The same sort of separation may be carried out by means of 80 percent sulfuric acid at 35° C. and 35 mm pressure (8).

Jan 1, 1950

By Robert Mehl

THE purpose of this investigation was to prepare high-purity iron-carbon alloys, to determine as precisely as possible the A3(GOS), the Acm(SE), and the A1(PSK) transformation temperatures in the meta-stable iron-iron carbide system (up to 1.4 per cent C), and to study the influence of carefully controlled and constant rates of heating and cooling (1/8 to 2° C. per minute) upon the transformation temperature and upon the resulting microstructure. Apart from the general metallurgical importance attending the completion of such a task, it will be noted that highly precise transformation temperatures are of interest and importance in the thermodynamic study of this system1. Several determinations of the iron-iron carbide diagram have been made. These suffer generally from the low purity of the alloys used, and from the application of methods of investigation of low sensitivity. Attempts to compare and weight the many data available in an effort to construct as accurate a diagram as possible have, in the main, been unsuccessful. In general, the wide differences in the results of different workers, the lack of complete analytical data, the omission of important details relating to the heat-treatment of the alloys, and the meager description of the methods of investigation applied, render such a process of averaging nearly meaningless. It may be seen from the summaries by Epstein2 and Körber and Oelsen1 that variations as great as 30° C. exist in the reported data on the A3 temperatures in iron-carbon alloys. For-tunately, the A3 temperature in pure iron is now known to be 910° C. ± 1° C.3 The best recent work on iron-carbon alloys is that of Esser4 on hypoeutectoid steels and that of Sato' on both hypoeutectoid and hyper-eutectoid steels.

Jan 1, 1937

By Paulo Couceiro, Manuel Lopez Cano, Carlos Rodgriguez Calvo

Apart from its difficult execution, underwater blasting is one of the most critical operations of the blasting techniques; mainly because of the ground vibrations - normally associated with low frequencies -, destructive hydraulic shock waves, the difficult coordination, and high costs. To solve these challenges during the underwater blasting on the expansion program for the Panama Canal “Widening and Deepening of the Pacific Entrance and the South approach Channel to the Third set of Locks of the Panama Canal”, a new method to blast using bulk explosive, developed by MAXAM, was used. The project was successfully executed, and more than 800.000m3 were blasted in less than 5 months, jointly with the biggest underwater drilling platform ever build, the Yuan Dong 007, with ten hydraulic drills on board guaranteeing a high production, excellent fragmentation result, total control of the vibration levels, no complain of the neighborhood surrounding the area of the project and simple local logistic due to the classification of the main product used (an oxidizer classified as 5.1). That was finally sensitized down in the hole.

Jan 1, 2011

By Ronald J. Roman

All mining and milling complexes can, within limits, operate at a variety of production rates. Factors of economic importance that are affected by production rates are costs per unit production, recovery and product grade. Once the relationship between the production rate and cost is established, dynamic programming techniques can be used to define the optimum production schedule (that is, the production schedule that maximizes the present worth of the operation) for the life of the deposit. In general, assuming that the capacity and efficiency of the physical plant remain unchanged throughout the life of the deposit, the optimum production rate is not constant for the life of the deposit, but declines gradually as the deposit is being exhausted.

Jan 1, 2014