Search Documents

By T. J. A. Smith

This paper provides an overview of some of the key issues in design of smelter gas handling systems, with particular reference to smelter smelting plants. In both primary smelting and converting, gas handling and treatment systems often represent the major capital cost component. There is also ample evidence that poor system design can be a major cause of smelter down time, lost production and unforeseen high maintenance costs. The paper discusses these issues and offers guidance for improved design.

Jan 1, 1992

By L. H. Duschak

"This paper is based on the results of work conducted of the bureau's experiment station at Berkeley, Calif., in connection with the investigation of properties and methods of utilizing Western magnesite. The experiments described herein were made under the supervision of the writer, by W. C. Riddell and E. H. Delius, of the station's staff.In calcining magnesite for the production of magnesium oxide to be used in the preparation of oxychloride cement, the calcium carbonate present in the original rock may remain unchanged or appear in the finished product, either as CaO, or in combination with SiO2, A12O3, etc. As there is reason to believe that free CaO may have an effect on the behavior of caustic magnesia in the cement reaction, it is desirable to have a method for the determination of the relatively small amounts of free CO in the presence of a large quantity of MgO.The extraction of the free CaO with water free from CO2 at once suggests itself as a possible method. The solubilities of Ca(OH2)2 and Mg(OH)2. are given by Seidell in his book an ""Solubility of Inorganic and Organic Compounds."" (2nd Edition, 1919) as follows:"

Jun 1, 1920

By A. Kenneth Schellinger

IF the ball mill is considered only from an energy standpoint, it can be thought of as a converter of kinetic energy into heat energy and surface energy. The law of the conservation of energy must apply to the ball mill as it does to any machine or process in nature. The heat energy output of the ball mill is apparent to any casual observer of the operating mill since the outflow pulp will be appreciably warmer than the inflow water and rock. The rock in the ball mill is crushed by shearing of its ionic bonding caused by some impact-induced stresses beyond the elastic limit. As the bonds holding the mineral crystal lattices together are ruptured, new surface area is created on each unit of which a definite number of unsaturated bonds exist. Such unsaturated energy of bonding may be termed the "surface energy," and is a potential energy figure. This created energy was withdrawn from the ball mill system and represents an absorption, or disappearance of heat. To reduce the size of the rock, surface area must be created and with it the at-

Jan 6, 1951

By T. M. Nasiatka

This report sterns from a study undertaken by the Federal Bureau of Mines to determine the possibility of reducing filter-cake moisture by applying radiant heat. Suitable laboratory equipment was set up to study the effect of heat, heating time, proximity of the heater to the filter cake, cake thickness, and other variables related to the final filter-cake moisture. A minus-48-mesh coal slurry and application of heat for 60 seconds resulted in filter-cake moistures 5.6 to 13.2 percentage points lower than could be accomplished by filtration alone at 24 inches of Hg for 1-1/4-and 1 1/2-inch cake thickness, respectively. The moisture reduction can be attributed to the combined effect of lower fluid viscosity and evaporation.

Jan 1, 1959

By Andrew L. Puwis

Methodologies were presented for computing the thermal gradient associated with single crystal solidification in macroscopic computer modeling. The. heat transfer, and solidification of a shaped investment casting model were simulated using properties from three different alloys. Following the simulation of solidification, the resultant thermal gradients (G) and rates of solidification (R) from representative points were extracted in various ways and compared: It was discovered that alloy properties have a strong influence on the computed thermal gradient and rate of solidification for the three methods investigated. Data also showed that the computed gradient for each model was very different depending on the temperature range used to compute these values.

Jan 1, 1994

Study on Iron Ore Sintering with High Proportion of Specularite Concentrates Specularite iron ores have poor hydrophilicity and ballability as well as bad high-temperature reactivity, which restricts the large-scale application in the sinter and pellet production. In order to make the best use of the specularite concentrates, a novel process of Composite Agglomeration Process (CAP) is applied in this research. By the CAP, the percentage of specularite concentrates in the sinter mixture is increased to no less than 40 per cent as well as the coke breeze dosage is reduced by 0.3 per cent~0.6 per cent. Moreover, all the sintering indexes are obviously improved compared with the traditional sintering process. Researches on the metallurgical performances shows the finished composite agglomerates are high-quality burdens for blast furnaces. This investigation can provide an effective route to utilize the inferior specularite concentrates in the sintering.

Sep 13, 2010

By L. Mukka

The existing main mine ventilation system for the production areas to the Kiruna mine was constructed during the period 1994-1996 and extended with 4 more shafts, including fan stations, for the sea ore body from 1997-1998. Two papers have been presented from this project at the 7th US Mine Ventilation Symposium in 1995 and at The 6th International Mine Ventilation Congress in 1997. In 2005, pre-studies for a new main haulage level were started. Different haulage methods were presented including ventilation systems. The pre-studies showed that the existing ventilation system, including fan stations for the new main haulage system in the production area, could be extended. However, a new system for the central area, which was not in the initial investment program, would be needed. In the beginning of 2006, a decision was made to design a new ventilation system for the central area to make it possible to get air to the development work for the new main haulage system, independent of the haulage method. This system was operational by the beginning of 2007. The new main haulage system, which was decided to be located on level 1365 m, only requires that the existing shafts be extended - the capacity of the fans seems to be enough. However, the problem is that the existing level 1045 m and the new level 1365 m have to be in operation in parallel for approximately 7-8 years. The challenge for the moment is determining how to ventilate the production areas for both levels at the same time, while simultaneously constructing the extended system. This paper will describe the problems associated with the extension of the main ventilation system and some potential solutions for these problems. The new main haulage level 1365 m must be in operation by 2012.

Jan 1, 2009

By Dolf Gielen

This paper discusses the results of a Western European energy and materials systems engineering study that analyses the impact of greenhouse gas (GHG) emission reduction on the future of the steel and aluminum industry. he technology selection will be significantly affected by future CO2 policies. The avail- ability of C02 removal and storage technology and the social acceptance of this strategy for GHG emission reduction is of key importance for the strategy selection. The use of coal based smelting reduction technologies is optimal in case of weak C02 policies or in case of strong C02 policies and low CO2 removal and storage costs. The selection of CCF or Corex technology depends on the penalty regime. However, if C02 removal proves to be problematic, CCF development fails and strong C02 policies are introduced, the gas based DRI production processes will become more attractive. In both cases, the energy efficiency of the iron and steel industry will further increase in the next decades. The impact of GHG emission reduction on aluminum prices and aluminum use can be significant. However contrary to common notions the aluminum production will be positively affected by GHG emission reduction, notwithstanding the currently high emissions in aluminum production. A combination of emission mitigation in production and significant GHG emission reduction effects further down the product chain cause this effect. A significant potential exists for improved materials efficiency. This potential is generally neglected in energy efficiency and CO2 reduction studies. However improved steel qualities are of similar importance for C02 emission reduction as increased energy efficiency. It remains to see if this potential will be used to its full extent in the next decades. Model calculations indicate that the impact of C02 policies on the competition with other materials will be limited. Greenhouse gas emission mitigation will have much more impact on materials production and waste handling than on materials consumption.

Jan 1, 1999

By Edward I. Erlich

1984 saw the 30th anniversary of a momentous event in Soviet geology-the discovery of kimberlites in Siberia, an event that vaulted the Soviet Union to second rank among the world's producers of both gem and industrial diamonds. There are many legends associated with this story, legends about those who predicted the discovery and those who achieved it in the field. The story told here unfolded during the field campaigns of the 1940s through 1960s, as witnessed by the authors and their companies of an earlier generation. This story illustrates science, chance, and human emotions at work, resulting in a blend of conviction, courage, bureaucratic sniping, and competition for glory. At the same time, it is an illustration of the workings of the Soviet exploration system. In a broader sense, it is the realization of the Russian image-boundless natural wealth, indomitable ingenuity, and the rigid political economic system that permeates the Russian landscape as well as the people. Most accounts of the Siberian diamond saga begin with statements such as, "This discovery confirmed the predictions of...", or "It was a result of predictions of one of the greatest Soviet geologists, Academician V.S. Sobelov...". These are only part of the truth. It had become apparent even in the 1930s that the Siberian Platform contained one of the Earth's greatest Basaltic provinces, described in a monograph by Sobolev...; and at the end of the thirties, G.G. Moor of the Institute of Arctic Geology found alnoites, similar in many ways to kimberlites. At the same time, the famous polar geologist, N.N. Urvantsev found other kimberlite like rocks in the southern Taymir Peninsula, adjacent to the Siberian Platform. In publications describing these rocks, Moor and Urvantsev mentioned for the first time the possibility of finding diamondiferous kimberlites similar to those in South Africa. Unfortunately, Urvantsev spent little time in the field between terms in concentration camps. Moor was considered by his superiors to be no more than a good descriptive petrographer; they suggested to him that his conclusions should be backed up by more highly regarded specialists. Thereupon, Moor asked Sobolev to coauthor a paper with him and this became the widely quoted prediction about diamonds in Siberia. Another early paper should also be mentioned, an unpublished paper found by M.I. Rabkin in the geological archives of the Norilsk Metallurgical Plant, written by Yu. M. Sheinmann when he worked in the concentration camp there in the late forties. This report placed the probable location of yet-to-be-discovered kimberlites within less than 100 km of their correct location.

Jan 1, 1990

By Marini David, Pigorini Andrea, Fuoco Stefano, Zurlo Raffaele

"The excavation of a tunnel in highly weathered and strongly fractured rock masses due to tectonic actions is still a challenge. In order to maintain reasonable productivity, excavation through a wide zone of highly tectonized rock mass requires a detailed, integrated study of the construction solutions and a monitoring system to minimize the process time and to optimize the adopted consolidation measures in accordance with a predefined matrix of possible support systems. This paper summarizes some interesting data acquired during the excavation of the Brenner Railway Base Tunnel system between Italy and Austria. The Brenner Base Tunnel (BBT) runs through the fault line between the European and the African tectonic plate. This big fault zone is called “Periadriatic Line.” In particular, data acquired in the exploratory-service tunnel have been analyzed. Furthermore, the base concepts for defining the consolidation and support solutions adopted for the excavation of the exploratory tunnel are described. INTRODUCTION The Brenner Railway Base Tunnel (BBT) is a system of underground structures and tunnels that is designed to connect Italy and Austria using new railway standards. It is based on high speed (HS) concepts and applies the European Standards for Interoperability (TSI). The railway includes twin tunnels for a total length of about 55.0 Km without considering the connection tunnels to the existing underground railway in Innsbruck. Including the latter, the total length of the tunnel system reaches 64 Km, and is among the longest tunnels in the world. The Italian section passes through the so-called ""Periadriatic Line,"" which is an important tectonic structure generated by the collision between the European and the African tectonic plates. Despite the extensive investigations carried out (boreholes down to 700 meter depth), significant geological and mechanical uncertainties inside the Periadriatic formations remained unsolved. In order to elevate the level of confidence and observe the behavior of the rock mass at a representative scale, the BBT Authority decided to excavate in advance the service tunnel, which has taken the function of an exploratory tunnel. The data and observations collected during its excavation would provide important insights for the design of the main tunnels."

Jan 1, 2016

By Scott A. Walker, Frank L. Rollo

"The San Francisco Museum of Modern Art (SFMOMA) in downtown metropolitan San Francisco, California, is supported on a mat foundation. Although the mat foundation of the original museum was designed to accommodate a future expansion, the plans for expansion that developed in 2010 required a larger footprint to accommodate the new space requirements of the museum. The new, larger expansion was designed by lead architect Snohetta. It will be a tall 12-story, steel-framed building occupying an area that was once the eastern part of the existing museum as well as two adjacent and newly acquired parcels.As designed, the expansion includes a 30-foot-deep excavation which is surrounded by adjacent buildings and improvements. Because of variable subsurface conditions at the site, geotechnical challenges included mitigating anticipated differential settlement between the existing and new foundations, preventing overstressing of the existing mat foundation, controlling groundwater to prevent settlement of surrounding improvements, and providing temporary support of adjacent structures during excavation for the new basement.To address several of the geotechnical challenges, soil-cement mixed (SMX) ground improvement was recommended by Treadwell & Rollo. However, during contract negotiations and construction, the specialty contractor proposed using jet grouting as an alternative technique for ground improvement. The jet grouting approach was accepted in principal, but when implemented was only marginally successful. Accordingly, the contractor eventually installed SMX panels using a Cutter Soil Mixing (CSM) machine. Because the CSM machine was a late arrival during construction, the contractor was not able to take advantage of the ground-improvement technique to install many of the shoring elements that we had originally recommended (such as the cut-off shoring wall). In the end, SMX panels were installed as ground-improvement beneath the new mat foundation to (1) reduce the potential for liquefaction in clean sand below the groundwater by providing increased rigidity to the soil, (2) reduce the potential for disturbing a weak underlying marsh deposit during construction, and (3) transfer vertical building loads to a layer of underlying dense sand.This paper also discusses the quality control and quality assurance programs that were implemented to check that the ground-improvement techniques used were thorough and complete and provided the required strength to transfer the new foundation loads to the underlying strata."

Jan 1, 2014

By Khandaker M. Anwar Hossain

This paper presents the development of lightweight concrete (LWC) incorporating pumice aggregate and volcanic ash (VA) based ASTM Type I blended cement (PVAC). Fresh and mechanical properties of LWC mixtures such as slump, air content, compressive strength, tensile strength, density and modulus of elasticity are described. The durability characteristics are investigated by drying shrinkage (DS) and water permeability. The investigation suggests the production of LWCs incorporating blended PVAC and VPA having satisfactory strength/durability characteristics for structural applications. The use of PVAC induces the beneficial effect of reducing drying shrinkage and water permeability. Development of such non- expensive and environmentally friendly LWCs with acceptable strength and durability characteristics is extremely helpful for the sustainable development and rehabilitation of volcanic disaster areas around the world.

Jan 1, 2010

By R. J. Brailey

"A USER'S VIEW OF CONVEYOR WEIGH SCALESThe Sudbury Operations of Falconbridge Nickel Mines Limited includes seven mines, three concentrators and a smelter. The flow of ore, concentrates, fuel and fluxes between and within these plants requires measurement for accounting and control. The design, installation and maintenance .of weighing systems falls within the responsibility of the Instrumentation Department of Falconbridge Nickel Mines thus al lowing a common approach to conveyor weighing problems and the benefit of a common spares supply. This paper gives a brief overview of the recent experience with conveyor scales within the Sudbury Operations and discusses the problem areas.GeneralThe best way to establish the total amount of material going to or from a process is with a bucket and a stop watch. Unfortunately the flowrates involved in mining plants make the buckets very large, but wherever it is feasible static weighing is the preferred method of determining total quantity. This applies particularly to batch systems, where the material can be brought to rest long enough to allow a very accurate weight determination. Any form of weighing in motion is susceptible to variations in the forces of the transporting system. A belt scale is affected by its position on the belt, idler alignment, support stiffness, variations in belt tension, material spills and build-up, and a host of other factors all of which require careful consideration in any installation.As with instrumentation applied to any system the plant should be designed to ensure that the best results can be obtained from the equipment. This means getting the scale supplier together with the conveyor supplier as early as possible in the designing of a new plant. Any corners cut in scale installation will be paid for later in poor results and/or increased maintenance."

Jan 1, 1975

By A. Ignatow

"A review is made of some of the principal factors and conditions that are, and will be, important to the over-all market climate for asbestos fibre and for the future of Canada's asbestos industry: - health hazard associated with asbestos exposure;- uncertain international regulatory environment for continued asbestos use;- adverse public reaction to asbestos;- product liability/litigation costs (U.S.A. primarily);- promotion of substitution by governments and asbestos user industries; and- minimal product and market development efforts by asbestos producing and consuming industries.In addition, Canadian producers, who export some 95 per cent of their production, face additional constraints:- dramatically reduced integration with asbestos-consuming industries;- 60 per cent of exports to most rapidly declining markets (U.S.A., Europe);- increased competition from offshore producers favourably located to growth markets in developing countries;- increasing production costs;- a strong dollar;- disadvantageous freight rates; and- loss of price leadership and price erosion.Future market trends, as well as prospects for Canada's asbestos industry, will be projected in this paper.Economic FactorsTable 1 presents asbestos fibre production in all countries for the period 1980-82. In certain instances, e.g. U.S.S.R. and China, these are capacity estimates as production statistics are not officially published. The U.S.S.R, by far, is the world's largest producer accounting for some 50 per cent of world production, though most production is consumed internally or by COMECON countries. It is estimated that some 700 plants produce asbestos-containing products within the U.S.S.R.Canada accounts for some 25 per cent of world production though it ranks first in world trade. Other important producers are South Africa Zimbabwe, Brazil and Italy. Since 1979, Canada's asbestos mining industry has experienced a dramatic drop in production and exports of asbestos fibre, as demonstrated in Table 2."

Jan 1, 1985

By K. Huang, L. Pan

"Darcy’s law has been used extensively to model cake filtration. It is a macroscopic model, in which particle size dominates the kinetics and cake moisture. In the present work, a capillary flow model has been developed from first principles to study the effects of microscopic parameters such as capillary radius, boundary layer slip, disjoining pressure, and surface tension that may be important for dewatering ultrafine particles. Laboratory-scale pressure filtration tests show that dewatering kinetics is strongly dependent on capillary radius, which in turn is influenced by surface hydrophobicity, surface charge, and length scales of particles. The model parameters determined from laboratory-scale filtration tests show that use of a hydrophobizing reagent can greatly improve fine particle filtration due to increased slip and decreased capillary pressure. The kinetics of dewatering kaolin clay is fastest at a pH where the layer-structured particles coagulate with a face-to-edge orientation. The capillary flow model developed in the present work may be useful for designing filters and optimizing operating conditions.INTRODUCTIONIn 2014, Canada produced 2.2 million barrels per day of crude oil from the oil sands resources in Alberta, which is expected to grow to 3.2–4.0 million barrels per day by 2030 (CAPP, 2013). One of the challenges to meeting these projections is the tailings management. At present, the industry uses ?77 km2 of the lands to construct tailings ponds. Significant amounts of the tailings disposed to the ponds are silts and clays that are slow to settle and consolidate, creating problems for reclamation. It is, therefore, the objective of the present work to develop a filtration model that may be useful for developing advanced dewatering technologies that can address the tailings management issues.Darcy’s equation is the governing law for filtration. It was derived as an empirical model by H. Darcy in 1856 while he was studying fluid flow in sand filters (Hall, 1956). Since then, many investigators derived it from first principles. It relates superficial fluid velocity to the pressure drop across a porous medium of known permeability. In filtration, the latter can be related empirically to particle size using the Kozney equation (Yoon, 2005)."

Jan 1, 2016

"The thiosulfate leaching process developed by Barrick to treat sulfidic high preg-robbing gold ores uses calcium thiosulfate as the leaching reagent for ores pre-treated by pressure oxidation, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a means of reagent recovery. A large portion of the research that led to the development of the technology was based on previous studies completed by different groups over the years, mainly focused on the ammonium thiosulfate system. Operational limitations in the use of the ammonia-containing recycled water in the pressure oxidation circuit were some of the main drivers for the change from ammonium to calcium thiosulfate for the development of the industrial scale process. One of the main aspects for successful gold extraction and recovery in the thiosulfate system is the pseudo-equilibrium reactions that drive distribution of the different gold species (in solids, solution and on resin) in the system. Previous studies have been focused on the thiosulfate reactions and equilibrium constants for the oxysulfur ions (thiosulfate, trithionate, tetrathionate). However, the literature around the effects of the different metal-oxysulfur complexes (Cu and Hg complexes) that form when the ore is in contact with the leaching reagents, and the related effects on stability of the gold complex is limited. The main changes in the gold complex chemistry and stability in the calcium thiosulfate system as compared to the ammonium and sodium equivalents, as well as related effects on gold recoveries, were investigated in the presence of different types of double refractory ores. INTRODUCTION Barrick has developed a thiosulfate leaching process to treat double refractory gold ores, by combining the use of acidic and alkaline autoclave pre-treatment with thiosulfate resin-in-leach (RIL). The process currently in operation at the Goldstrike mine (the TCM process), uses calcium thiosulfate as the leaching reagent, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a mean of reagent recycle. The main feed to the process plant is highly preg-robbing sulfidic ore from Goldstrike’s open pit. Prior to feeding the pressure oxidation circuit, the ore is processed through the crushing and grinding circuits and treated in preparation for acid or alkaline autoclave processing (POX)."

Jan 1, 2018

By G. Johnston, P. K. Chatterjee, S. Holguin

M. Gershon The article is an excellent one, providing a basis for the conduct of the major tasks in underground mine planning and scheduling. I object to only one word. Since that word is featured in the title, it is a strong objection. The word used erroneously is optimization. There is no optimization performed in the article. By definition, an optimization is an approach that yields the best of all possible solutions. We can limit this definition to its narrowest sense, the optimization techniques of operations research such as linear programming, or broaden it to include less sophisticated search procedures that find the best mine plan or schedule. No such claim is made in the article. No optimization of any kind is performed. The major tool used is a simulation, which, in truth, is probably more appropriate for this problem than any optimization. But simulation does not optimize. It only allows for quick evaluation of many options, leading to the selection of the best plan "of those tried," not "of all possible plans." This article, of course, is not the first mining paper to make this error. It seems that the word optimization is used more to impress people than to refer to any act of optimizing. It is used in a way that implies "try to optimize"or "come close to optimize," but not to really do it. It is usually appropriate to quietly ignore this error. But when Dr. Chatterjee, who has done so much good work in true optimization projects and whose work I have come to admire, makes such an error, it is time to publicly dispute it. Having discussed this very point with him in the past, I am sure that he will agree. If he can support this position in his response, perhaps people will start to listen and we can reduce the number of false claims of optimization. This should be easy for him in this case since the approach he used, simulation, is the more appropriate one anyway.

Jan 8, 1988

By E. O. Stensholt

The Hybinette electrorefining process for production of cathode nickel was in use at Falconbridge Nikkelverk A/S, Norway, until 1975 when conversion to the new chlorine leach process was started. In 1978 the conversion to electrowinning had been completed, but further major improvements to the process have been made up to 1987. After a major expansion program in 1985 - 87 the refinery has a nickel capacity of 54 000 mt Ni/year. The main feed materials to the process are converter matte from the Falconbridge smelter in Sudbury, Ontario, Canada, and from the BCL smelter in Selebi-Phikwe, Botswana. A typical composition of the mixed feed to the refinery is: 40 - 45% Ni, 25 - 30% Cu, 20 - 22% S, 2 - 3% Fe and 1.0 - 1.5% Co. The matte is chlorine-leached in the first process step, nickel being dissolved selectively in a train of leach-cementation tanks. Essentially all copper and sulphur that was present in matte appears in the leach residue as CuS. In 1986 an autoclave treatment stage was added to the process to improve nickel extraction from the leach residue. The resulting strong nickel chloride solution is purified by the process steps (1) precipitation of iron and arsenic, (2) solvent extraction of cobalt and other minor elements and (3) precipitation of lead and the remaining impurities. The nickel solution is then fed to the tankhouse, where various nickel products are produced by electrowinning. The chlorine gas that is produced during the electrolysis is returned directly to the chlorine leaching tanks to dissolve more matte. After stripping from the loaded organic phase and solution purification cobalt is also produced by electrowinning. The copper sulphide leach residue, which contains some nickel, is dead- roasted in fluidized-bed roasters. The sulphur is recovered and sold as sulphuric acid. The calcine is leached in spent copper electrolyte, from which cathode copper is produced by electrowinning. Precious metals and the remaining base metals are recovered from the copper leach residue. The Falconbridge chlorine process is very versatile. It can accept a wide range of impurities in the feed and still produce metals of exceptional purity.

Jan 1, 1988

By L. G. Smith, C. A. Shook, W. H. W. Husband, W. Schriek

"The flow of slurries in pipelines is governed by many variables, and the study of the influence of each of these variables is difficult, if not impossible, in some cases. Many correlations are available which fit data within a given range. However, no one method is yet available to design a slurry pipeline for all desired conditions without at least some physical measurements on the slurry itself. For this reason, the slurry pipeline facilities at the Saskatchewan Research Council have been developed during the past 12 years and it is hoped that the development will continue until the process is thoroughly understood and test facilities are no longer necessary. This paper outlines methods currently used and under development at the Saskatchewan Research Council for measurement, control and study of the variables governing the flow of slurries."

Jan 1, 1973

By Tomoya Kawasaki, Tatsuya Motomura, Yutaka Yasuda

Saganoseki Smelter, one of the largest copper producers in Japan, currently operates a single flash smelting furnace to produce 450,000 tons of new copper annually. The smelter used to employ two flash furnaces, and integrated the two into one in 1996. Since then, various improvements to its facilities and technologies have been made to increase productivity. To upgrade the operation efficiency, "stability" was considered a key issue, and the measures were taken to increase the operation and facility reliability. Currently, the furnace is running at a feed rate of 215 DMT/h, while the furnace utilization has been maintained at 97%. This paper outlines recent improvements that have made to increase furnace productivity and efficiency.

Jan 1, 2014