Search Documents

By Axel Doelcken

?? Liebherr excavators in standard configuration are generally designed to operate in an ambient temperature range between -12°C and +55°C (10.4 °F and 131°F). ?? To operate effectively and efficiently in very low temperatures special consideration needs to be given to the design ??An inappropriately designed hydraulic system unable to withstand extreme changes in temperatures or varying working conditions will lead to: - premature wear and more frequent replacement of components - increased maintenance & unplanned downtime This will affect productivity & operating costs.

May 1, 2008

By Hayward B. Oblad

The effects of eight independent variables on froth flotation product yield, ash content, and coal recovery were studied using laboratory batch flotation of 0.6 am x 0 coal. The eight flotation variables investigated were air feed rate, pre-dispersion of collector oil, impeller speed, product collection time, initial solids concentration, collector conditioning time, frother (methyl isobutyl carbinol) concentration, and collector (No. 2 fuel oil) dosage. The two-level Plackett-Burman screening design and the three-level Box-Behnken design were used. Within the ranges studied, air feed rate had no effect on product yield. Pre-dispersion of collector oil, impeller speed, product collection time, initial solids concentration, and collector conditioning time showed only minor effects on the product yield and quality. Frother concentration (mg/L) in the process water and collector oil dosage (g/kg) were shown to be the dominant independent variables in coal froth flotation. Flotation experiments that vary initial solids concentration at constant frother dosage (g/kg) confound the effects of frother concentration (mg/L) and solids concentration. The dominating effects of frother concentration and oil dosage on coal recovery and froth product ash content are illustrated with three-dimensional plots. The relationship between froth product ash and coal recovery is also clearly illustrated by the flotation data.

Jan 1, 1985

By G. H. Lewis, C. L. Krcil, N. S. Harding, D. E. Havekotte

INTRODUCTION Limestone injection work was completed in a 440-kW (1.5-million Btu per hour) pilot-scale combustor in preparation for a 50,000-kg/h (110,000-lb per hour) industrial steam boiler limestone injection test program. The main objectives were to: (1) identify the important variables that affect sulfur capture, (2) determine the maximum SO2 removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. A more detailed report is given by Lewis et al. (1985). The test program was divided into two phases. The objectives of Phase I were to determine the important variables that affect SO2 reduction and to investigate the effect of limestone addition on combustor operation and heat transfer surfaces. The objective of Phase II was to determine, using only the important variables identified during Phase I, the conditions that resulted in the greatest sulfur dioxide reduction. Phase I Test program Using one limestone, five variables were identified as having an effect on SO2 reduction. These are noted with their respective ranges: heat release rate [103 to 166 kW/m3 (10,000 to 16,000 Btu per hour-cu ft)], Ca/S molar ratio (0 to 3), flue gas oxygen concentration (3% to 5%), additive particle size [90% -150 µm (-100 mesh) and 90% -45 µm (-325 mesh)], and burner stoichiometry (SR = 0.75 and >1.15). A 2.3% sulfur northern West Virginia coal, pulverized to a nominal grind of 70% -75 µm (-200 mesh), was burned for the tests. The limestone used was obtained from a Maysville, KY, quarry and contained 51.75% (wt) CaO. An 11-run statistically designed program (plus three duplicates) was used to screen the five variables. The effect of limestone injection on the combustor heat transfer surfaces was determined by comparing the heat transfer rates through a slag panel and fouling probes during periods with and without limestone injection. Combustor operation was determined by noting any operating problems that occurred during the tests. Test procedure After furnace wall temperatures had stabilized at operating conditions, heat transfer surfaces (slag panel and fouling probes) and the convection section were blown clean, and a four-hour test was begun. The

Jan 1, 1987

By D. D. Marsden, L. E. Kun

Although a regulation is in force that all water used underground shall be free of bacterial contamination, in practice it is often very difficult to accomplish this. The standard method of disinfection m South African mines IS treatment with calcium hypochlorite, although liquid sodium hypochlorite is used at a few sites. Primarily because the process depends on human control for the addition of the hypochlorite and the regulation of its now, it is frequently found difficult to disinfect mine water adequately and continuously. In many marine environments, chlorine generated by the electrolysis of seawater in its passage through an electric cell is used for disinfection. The generation procedure is continuous and needs no human control except for occasional checking of the equipment. This paper describes the successful implementation of the process, suitably .modified, .at four underground sites. After severe scaling problems had been overcome, a procedure resulted that chlorinates considerably more effectively than the previous system (dosing with calcium hypochlorite), and that has a lower amortized operating cost.

Jan 1, 1981

By A. B. Hooker

Nineteen of the installations were on rental contracts 1.L."'1der whtch the lamps belong to the lamp company and are rented by t.½em to the mine operatj.nt; company. · The other nine installations had been upon an O\Vnership-rental basis, by which the lamps had become the property of the renter at the end of 5 years. Five of t.11e rentec installations were en a special contract calling for a guaranteed light output. These contr2.cts were based upon certified . initial performance, with the provision that the lamps be replaced whenever periodic tests of fully charged lamps, taken at random from t..h.e charge racks, showed a light output of less than 80 percent of the certified performance.

Jan 1, 1942

By F. A. Baczek

The Electroslurry TM electrowinning concept has been incorporated into a process flowsheet for recovering copper from smelter flue dusts. The process has averaged 96% recovery of the copper as high-grade electrowon while at the same time removing a majority of the impurities that degrade drawn copper as a result of recycling flue dust and liberator cathodes: The dust is processed through several stages consisting of leaching, copper precipitation, Electroslurry TM electrowinning and waste liquor treatment. The process may be integrated into a smelter operation and become an effective and feasible means of maintaining good product purity.

Jan 1, 1980

By J. E. Neal, C. T. Naber, O&apos

Silicon thin films were deposited by electron beam evaporation in an ultrahigh vacuum onto (0001) and (1102) sapphire substrates. Attempts were made to correlate the structural properties of the deposited silicon films with the following: 1) substrate orientation, 2) substrate surface condition, 3) substrate temperature, and 4) deposition rate. The substrate temperatures were varied between 500° and 1000°C and the deposition rates were varied between approximately 50 and 700A per min. The following sapphire surface treatments were investigated: 1) annealing in the ultrahigh vacuum at 1200° C; 2) heating in a hydrogen atmosphere at about 1350°C; and 3) etching with silicon by evaporating silicon onto sapphire substrates heated to 1200° or 1300°C. Twinned silicon films were occasionally formed at substrate temperatures between the 800° and 1000°C on unprocessed mechanically polished substrates; however, the reproducibility and crystallinity of these films were generally poor. Single-crystal and twinned silicon films were formed at substrate temperatures between 700° and 1000°C on substrates which were silicon-etched at 1300°C prior to deposition. Fiber texture films were formed at substrate temperatures between 500° and 700°C. The (111) lattice plane of the silicon single-crystal films was parallel to the (0001) sapphire plane and the (100) silicon plane was parallel to the (1102) sapphire plane. TECHNIQUES are well-established for growing single-crystal silicon thin films on sapphire by chemical methods.'-* Vacuum epitaxial techniques have a number of advantages over chemical epitaxial techniques in the fabrication of thin film microcircuits.5 One of the most significant is that vacuum techniques are compatible with well-established procedures for forming vacuum-deposited thin-film resistors, capacitors, and interconnections. Salatna, Tucker, and young6 recently reported the formation of relatively poor crystalline-quality silicon films on sapphire by electron beam evaporation in a vacuum of about 7 x 10-7 Torr. The purpose of the investigation described here is to determine the relationships between the structural properties of silicon thin films deposited on sapphire substrates by electron beam evaporation in an ultra-high vacuum and the following: 1) substrate orientation; 2) substrate surface condition; 3) substrate temperature; and 4) deposition rate. The substrate temperatures were varied between 500° and 1000° C and the deposition rates were varied between approximately 50 and 700A per min. Two orientations of sapphire were used: (0001) and (1102). The thick-nesses of the films were between 8000 and 16,000A. The morphology and crystallinity of the deposited films and substrate surfaces were investigated by optical microscopy, electron microscopy, and electron diffraction. APPARATUS AND PROCEDURE A cross section of the ultrahigh-vacuum thin-film evaporator is shown in Fig. 1. The bell jar is stainless steel and copper gaskets are utilized at all seals. High vacuum is attained by a 6001iter per sec ion pump and a titanium sublimation pump. Sorption pumps are used to rough the system to a pressure of about 10 µ prior to starting the ion pump. Vacuums in the 10- 10 Torr range were attained after baking the system at about 250°C for 8 hr. Vacuums in the 10-8 to 10-9 Torr range were maintained during silicon evaporation. The silicon charges, which were cut from p-type single-crystal boules which had resistivities between 2000 and 4500 ohm-cm, were placed in the water-cooled copper crucible of a 180 deg bent-beam 5-kw electron beam evaporator. During evaporation, a molten zone was formed in the top center of the silicon charge, and the portion of the silicon charge in contact with the water-cooled crucible remained solid. The substrate heater, which has been described

Jan 1, 1969

By M Dietrich

The paper describes an efficient method for analysing the different attachment kinematics of excavators and other linkages by taking into account digging forces, the workspace and the stability of the machines. The different attachment kinematic systems of hydraulic excavators and a æclassical analysing methodÆ will be presented. The method was integrated as a plug-in for the multibody simulation (MBS) software MSC.ADAMS to create an easy to use solution for design engineers. A comparison of the new MBS-solution with the classical static analysis is a part of this paper and shows the advantages of the new method. This takes into account the manifold and new dynamic analysing opportunities, as well as more detailed models leading to more accurate results.

Sep 26, 2011

By T. H. Jeffers

The Bureau of Mines conducted laboratory tests to devise a procedure for extracting copper from low-grade discarded mill tailings. A solid extractant consisting of an organic solvent extraction reagent adsorbed on granular activated carbon was investigated and proved to be satisfactory for extracting copper directly from leach pulps. When this material was used in a cyclic leaching, stripping, and electrowinning pro-cess, 95 pct of the acid-soluble copper was recovered from oxidized mill tailings. The weathered tailings contained 0.24 pct Cu (total) and 0.20 pct acid-soluble Cu. The copper was recovered as cathodes containing, in parts per million, 1.6 Pb, 3.6 Fe, 0.5 Sb, 1.5 AI, 1.9 Mn, and <1 Mg.

Jan 1, 1985

WALTER N. CRAFTS,* Toronto, Canada (written discussion?).-During the forging of 9.2-in. shells -for the United States Army, it was noticed that better results were obtained in certain instances when test bars had been held sometime before pulling. An investigation, therefore, was made by our metallographer, Mr. F. M. Arnold, to determine the effect of seasoning. The forging consists of a single operation, piercing a solid cast blank. The test sections were cut from the walls by an oxyacetylene flame, one piece from the nose end and one from the base on the opposite side. The test pieces were not heat treated in any way and the tests and seasonings were carried on at normal atmospheric temperatures. The specifica-tions were as follows: Standard 2-in. test bar, 0.505 in. in diameter; elastic limit, over 19 long tons, or 42,500 lb.; ultimate stress, 39.6 to 49.1 long tons, or 87,500 to 110,000 lb. per sq. in.; elongation, over 13 per cent. As a preliminary test two heats were selected; BP555, which was tested and reported failed on elongation on Aug. 20; and B01771, which was tested and reported failed on Aug. 24. On Aug. 29, retests were cut and machined from the same shells and held till Sept. 3 (5 days) when they were pulled. Both sets of results are given below.

Jan 12, 1919

Mining steeply dipping coal seams is a difficult task in the mining industry. Prior to 1996, fully mechanized longwall mining methods along the seam strike direction were tried in China and other countries. Due to its larger coal reserve in steep seams, China made more but still limited progresses on mining in such seams than the other major coal-mining countries. In the last two decades, accelerated research efforts have been made to improve the mining technology in steeply dipping coal seams. Based on these works, a dynamic model of ?R-S-F? system under asymmetrical constrains in mining steep seam is established and the theory of strata control and hazard prevention begin to be formed. The key technologies for mining steep coal seams include: global and regional strata control methods in longwall face, methods for the longwall face machines to sustain static and dynamic loads, and flexible protection technology. These theory and technologies have been successfully applied to mining of steep coal seams of varying thickness and hardness, with hard and soft roof and floor, and with high potential of spontaneous combustion in China. In the recent years, the technology has been introduced to Russia, India, Uzbekistan and other countries where steep coal seams are mined.

Jan 1, 2012

By H. B. Weaver

The development of a method to manufacture diamonds has been rated as one of the out- standing scientific achievements of our time. The story is both interesting and significant. This paper will quickly review history of diamond and manufactured diamond. Next, it will discuss manufactured diamond as a product -- how good is it -- and what is the significance of this scientific achievement. And finally, present a few thoughts about the future of this technology and this product. For centuries, diamond was found only in alluvial deposits, primarily in the Golconda fields of India. As a result, man knew nothing of the process by which the stones were formed. In 1860, diamonds were found in South Africa under completely different conditions. Here, for the first time, they were found in volcanic pipe -- their mother ground. These volcanic pipes are roughly cylindrical columns of rock which go deep within the earth. The theory as to the formation of diamond was presented by the geologists in that era. The theory states that molten rock was thrust up through a layer of carbonaceous shale where it picked up the carbon necessary for diamond formation. It was generally agreed that diamond was formed approximately 240 miles below the surface of the earth, thus indicating that extremely high temperatures and pressures were involved.

Jan 1, 1964

By A. T. Iannacchione

Recent fatal injuries occurring during pillar retreat coal mining call for better identification of the hazards and recognition of risks. Ground control hazards associated with room-and-pillar retreat mining tend to intensify with depth, requiring extra precautions in the form of additional controls. In many locations these activities are further complicated by local complexities often associated with unique or novel circumstances, such as over-mining or under-mining. One technique recently studied by NIOSH, Major Hazard Risk Assessment (MHRA), may help mine operators to mitigate the risks associated with pillar recovery operations. The approach was trialed at two underground coal mines in southern West Virginia that are currently practicing pillar recovery. The first step in the MHRA process involved reviewing the segments or parts of the pillar extraction mining system and identifying associated hazards and threats to the operation. Some of the high risk hazards at these two sites included: ? Rock fall during pillar extraction covers equipment and injury ? occurs during recovery operations, Rock fall above the roof bolt horizon, potentially injuring ? workers and/or requiring recovery action,Rib fall under deep cover, potentially injuring workers, and; ? Strata instabilities associated with subsidence of the ? interburden due to simultaneously mining two seams in close vertical proximity to one another. The mines? risk assessment teams then considered each threat individually in order to systematically identify potential unwanted events. The top unwanted events were examined individually using structured risk analysis tools. The output from the process includes a list of priority existing controls for monitoring and auditing, and a second list of potential new controls. These controls consisted of: ? Examples of best practices, ? Enhanced communication, ? Implementing standard operating procedures (SOP), ? Protocols for emergency response actions, ? Effective layouts, ? Efficient monitoring, and; ? Successful audits. This paper documents the process as it unfolded at the two mines, and analyzes the strengths and weaknesses of the MHRA technique as it applies to pillar recovery operations. This work was part of a larger NIOSH research project. NIOSH was responsible for: 1) facilitating the risk assessment process known as Major Hazard Risk Assessment (MHRA), 2) documenting the risk assessment process, and 3) providing mine management with a written draft summary of the risk assessment process. The results of the risk assessment represent the thoughts and opinions of the individual risk assessment teams and should in no way be construed as an endorsement of the risk assessment output by NIOSH or the University of Pittsburgh.

Jan 1, 2009

By Qing-Xun Low

Ni current collector has excellent electronic conductivity and mechanica, properties. However, nicke, cannot be used in H2S-containing syngas SOFCs due to sulfur poisoning and coking. Copper coated nicke, is prepared by electrochemica, deposition. XRD, SEM, and EDX techniques are used to characterize the samples. After high temperature treatment in syngas containing, the coated samples exhibit high resistance of coke formation and sulfur corrosion compared to pure nickel. Therefore, copper coated nicke, is a promising anode current collector for H2S-containing syngas SOFCs.

Jan 1, 2010

By Thomas L. Barkley, Michael A. Indihar

The new Cyprus Northshore Mining Co. has taken the previous blasting methods of Reserve Mining Co.'s mine in northern Minnesota and adapted them to a new competative Iron Ore Industry. Cyprus was challenged to develop new blasting methods to reduce costs and improve results over the previous mining operation. Many of the older procedures have been kept, but others have been changed in ways that bring the mine operation up to state of the art technology. In addition, unique ideas not previously tried in the North American Iron Ore Industry have been instituted. So far, this has reduced Cyprus's blasting costs by 70 percent.

Jan 1, 1991

By Q. Zhang

The necessary capability of the gravity transportation pipeline system for cemented coal gangue backfilling at the Suncun Coal Mine, China, is about 74.4 m3?h-1 according to mining production and working times in the mine. It is estimated that the working velocity and maximum pipe length-backfill depth ratio of the backfill system are 3.82m?s-1 and 5.4, respectively and that the probable backfill capability of the system is 110.18m3?h-1. Results of hydraulic calculations for the backfill transportation system show that the designed backfill system is reliable in flowability and sufficient for backfill capability needs.

May 1, 2007

By S J. Brace

About 180 000 tons of explosives are used annually underground in South Africa. Most is loaded into holes less than 50mm in diameter. 75% is consumed in the gold and platinum mines where holes are between 25 and 4omm in diameter and no more than 3.0m in length. The small amount of explosives per hole with extreme conditions of heat, humidity and seismic activity, make the choice of explosive on safety and technical grounds very important to the success of a blasting operation. Taken together with the fact that many underground precious metal operations are now marginal then the choice of an explosive, when its price is also considered, becomes critical to the very viability of some mines.

Jan 1, 1994

By M. Clair Smith

This report is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods, and costs at various open-pit mines in the United States. These reports have been prepared in cooperation with various mining companies. A similar program, conducted from 1928 to 1939, was generally conceded to have contributed to improving the efficiency of mining operations. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technological information on mining methods and practices. This report describes exploration, development, equipment, and mining by open-pit methods of the remainder of an ore body that had been previously worked by underground methods. The Tripp pit of the Consolidated Coppermines Corp. is located at Kimberly, Nev., a small mining company town having an elevation of 7,250 feet, 9 miles by road west of Ely, Nev. (fig. 1). The pit extends over the area formerly mined by underground methods from the Morris and Brooks shafts.

Jan 1, 1962

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999

By Prakash Venkatesan, Mehmet Ali Recai Ӧnal, Shaik Saida, Veerendra Singh, Chenna Rao Borra, Manish Kumar Kar

A laboratory-scale investigation of the effect of milling operation and catalyst addition ( K2CO3) on the partial reduction of low-grade pyrolusite ore pellets was carried out using coke as a reductant. Thermogravimetric analysis was used to understand the correlation between milling and catalyst addition parameters with the reduction temperatures. DTG analysis of pyrolusite pellet reduction showed three distinctive peaks associated with a three-step reduction mechanism (i.e., MnO2→ Mn2O3→Mn3O4→MnO). The results showed that the grinding and addition of the catalyst have a significant effect on lowering the MnO2 reduction temperature independently. But maximum reduction temperature drop is obtained when combining grinding and catalyst addition in this work. By 3 h milling and 10 wt% catalyst addition, the reduction temperatures were reduced by more than 200 °C compared to the raw ore pellets. These results obtained from the DTG analysis were further supported by XRD analysis of the reduced samples.

Dec 20, 2022