Search Documents

By Raymond B. Hryciuk

Environmental auditing has evolved rapidly over the last decade — first in North America, then Europe, and most recently in Asia — into a widely practiced discipline designed to provide senior management with assurance that operations are being managed in compliance with established governmental standards, internal company policies, and good industry practices. This paper first examines the evolution of environmental auditing, focusing in particular on three interlocking driving forces: company initiatives, collaborative industry initiatives, and government initiatives. Characteristics of effective audit programs, those that have emerged among the leaders, are discussed, including: objectives, scope, coverage, approach, staffing, and organizational considerations. The author then addresses important future trends and developments for environmental audit program design, content, and coverage.

Jan 1, 1996

By F. P. Haver

The Bureau of Mines has investigated the electrochemical reduction of lead chloride as a method for producing lead without the pollution problems associated with smelting. It was determined that high-purity metal (>99.9 pct Pb) could be obtained, using PbC12 prepared by ferric chloride leaching of galena concentrate: PbS + 2FeCl3?PbCl2 + 2FeC12 + S°. Optimum results in small-scale electrolytic tests were achieved with a bath consisting of 40 to 70 wt-pct PbCl2 dissolved in KC1-LiCl eutectic, an operating temperature of 450° C, a current density of 2.5 amp/in2, and an electrode spacing of 0.5 inch. In large-scale tests made to develop a cell design for commercial application, the optimum electrode arrangement proved to be a bipolar configuration with horizontal plates. This gave a current efficiency of 86 pct with an energy requirement of 0.52 kwhr/lb lead. To determine the effect of impurity buildup in the bath, 1,200 lb of PbC12 prepared by ferric chloride leaching of galena concentrate was electrolyzed over a period of 2 months. Little deterioration of the metal quality occurred in that time; all of the lead produced had a purity equal to or better than corroding grade (>99.94 pct Pb).

Jan 1, 1976

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

By Jeffrey Shawn Peterson

In past years, the U.S. Bureau of Mines has been involved in safety research that could ultimately re-late the conditions of spark testing and actual use by estimating the simple ignition probability of a circuit in question. A major problem in estimating this probability is that results show a significant variability, even though gas mixtures and electrical parameters may be closely controlled. Some researchers have suggested that the ambient environmental conditions of the testing may influence the results. A series of tests were conducted using a spark test apparatus to simulate a failing electrical circuit. By independently adjusting the temperature, pressure, or relative humidity of the combustible gas mixture, multiple test environments were examined. At each ignition, a computer re-corded the temperature, pressure, and relative humidity of the gas immediately prior to the explosion. These data were then used to establish the effect of the test environment on the ignition probability and to create a mathematical model of the test environment's synergistic effects. The analysis indicated that these effects were not as significant as previously expected. No general algorithm was found that could be used to predict these effects across the range of circuits tested.

Jan 1, 2010

By R. Srikanth

Dust control in high production longwalls is a major problem requiring, among other things, careful attention to the design of operating practices, and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in U.S. longwalls; yet under certain conditions, 31 percent of the shearer operator's dust exposure can be due to support movement. Several methods have been developed for the control of shield-generated dust. Yet the need for better methods is apparent. In this paper, the amount of airborne respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. A total of ten experiments were conducted in five longwall faces in four different mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne respirable dust concentration immediately downwind of the shield moved, varied between 0.12 and 1. 75 mg/m3 in the five longwall faces. The mass of airborne respirable dust generated by shield movement was found to vary between 39 and 386 milligrams per shield move. The results from this study reveal that control of dust from longwall shields requires a combination of approaches involving alternative operating practices, reducing shield dust generation rate, increasing face air flow, and decreasing personnel exposure.

Jan 1, 1994

By John Paul Gries

This Bureau of Mines study outlines the history of 11 major metal ore deposits or districts that are relatively new discoveries. The oldest operation is the White Pine mine, where major exploration was initiated in 1929. Discovery (delineation of ore bodies) dates range from 1948 to 1976. All but two of the deposits, Quartz Hill in Alaska and Flambeau in Wisconsin, are or shortly will be in major production.

Jan 1, 1979

By F. E. Joyce, Charles Prasky

This report describes the response to high- temperature sulfatization of a variety of manganese minerals and companion compounds which may occur either as a principal component or as a gangue material in low- grade manganese deposits . Fourteen manganese samples representing oxide , carbonate , and silicate minerals as well as seven compounds which might occur as gangue with manganese minerals were tested batchwise in a bench- scale apparatus under conditions which would be favorable for the sulfatization of manganese . The manganese minerals substantiated thermodynamic predictions and responded to sulfatization but to varying degrees . The gangue materials , MgO , MgCO,, CaO , and CaCO3 , were sulfatized readily in contrast to the iron oxides and the aluminacontaining material which were not .

Jan 1, 1964

By Anton Gronningsater

MR. J. R. GORDON: The authors are to be congratulated for their excellent papers on Copper-Nickel Matte Converting. Mr. Drummond's paper contains the results of a thorough and exhaustive study of a series of converter charges. Mr. Gronningsater has presented convincing arguments in favour of his claim that the converter has been neglected as a smelting machine for ore. Some of us may not be inclined to agree with his conclusions. Converting, like most metallurgical operations, is a compromise between an ideal and a practical operation. If it were possible for one to neglect entirely the matter of converter linings, I believe we would all agree that the proper flux for matte in a converter would be pure quartz. Under such ideal conditions, one would, if proper temperature were maintained, make the smallest quantity of slag containing a minimum of magnetite. Converter slags are notorious for their high metal content and must always be subjected to a further cleaning treatment before being discarded. For that reason, the tonnage of converter slag produced should be minimized. If norite is used as a converter flux, then the tonnage of converter slag would be greatly increased if the silica content is maintained at 27 per cent or higher. I cannot agree with Mr. Gronningsater's suggestion that, in con¬sidering a converter flux, the sum of the silica, alumina, alkaline-earths, and alkalis should be considered as being of value. The alkalis and alkaline-earth contents of the flux will replace iron in the silicates formed and tend to increase the viscosity of the slags. However, if the converter is to be used as a smelting machine, it will be necessary to drop the silica content of the converter slag in order to avoid production of excessive slag tonnages.

Jan 1, 1942

By Felix Edgar Wormser

JUST as the ancients used the products of their crude mining endeavors to fashion tools with which to make digging easier, so today mining enterprises are dependent upon the very metals they mine for the efficient conduct of mining and metallurgical operations. In fact, the outlet afforded by the production of minerals in the United States is no mean market for the nonferrous metals. I believe that mine managers frequently lose sight of the opportunity they have to select from competitive products those which will help the market for their own metal output. For example, some years ago a large lead mine used storage-battery locomotives for its haulage, common practice, of course, throughout the United States. These particular locomotives, however, were powered not with the ordinary lead storage battery but by a competitive battery product made from an imported metal. After studying this situation, the manager saw how he could help himself by purchasing a product made from his own mineral output, and in his next order turned tip the use of the lead storage battery.

Jan 1, 1935

By C A. Chaves

During most of its history, the metallurgical industry has been seen as a source of pollution for the environment. However, during the second half of the 20th century, as the world environmental legislation became more protective and the global environmental conscience consolidated, this landscape began to change. Metallurgical activities have become increasingly related to the social and environmental impacts caused by human activities. With the adoption of environmental management in steel plants, there has been a significant change in steel-related activities which have begun to introduce modern plants, managed with environmental, social and productive efficiency. More and more, steel companies search for a decrease in negative impacts of their industrial operations on the environment, fitting them to the current environmental legislation and even increasing productivity and profitability. The steel industry has started to become a clean and more efficient industry. This work presents a case study of a sustainable steel plant project, located in an environmental preservation area. The project includes treatment and reuse of industrial liquid effluents, air emissions control, noise control, recycling, recovery and adequate waste management. It also incorporates production processes using clean technologies, capable of coproducing energy resources which may be used in the plant showing how is it possible to produce steel with environmental and social responsibility and even increase the enterpriseÆs profitability.

Jan 1, 2009

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines (USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two for-mulations resulted in stable gels that lasted for at least 12 months in the mine. Semicontinuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both in terms of productivity and enhanced mine safety.

Jan 1, 2010

By R. B. Elver

The level of steel consumption per capita is one of the principal indicators of a country's standard of living. It is no coincidence that the materially advanced nations possess viable iron and steel industries to provide a reliable and economic source of steal for the manufacturing industries. No other metal is as dominantly important in manufacturing as steel. The blast furnace - steel furnace complex based on coking coal, ferrous scrap and iron ore - continues to be the principal steel-producing method. Less important is the electric furnace method based on scrap, In recent years, there has been considerable interest in the many direct reduction processes that are not dependent on coking coal but usually produce a product for further refining in steel furnaces. No matter which series of processes are used, iron ore is essentially the only source of virgin iron units. Thus, to such a vital and capital-intense industry as steel, access to a relatively inexpensive, long- term supply of iron ore is essential.

Jan 1, 1964

By R. Adams

Zirconium is the 20th most abundant element in the Earth?s crust and it most often occurs in the form of silicate (as zircon), less often in the oxide form (as baddeleyite or caldesite). Historically, the world?s production of zircon was entirely derived from mining and processing beach sands or heavy mineral sands that were being exploited primarily for their titanium content, i.e., to generate TiO2 feedstocks that would be used for making titanium pigments and, to a lesser extent, titanium metal. Zircon was then regarded as a byproduct, with the sharply fluctuating prices typical of a commodity where the supply is essentially involuntary and not truly responsive to market demand. However, in recent years, zircon has shown considerable mining investment appeal in its own right. Projects have been planned ? and some have already come to fruition ? based mainly on the zircon potential of the deposit. Booming Chinese demand for zircon to meet the requirements of the ceramic and zirconium chemical sectors has been a major factor causing zircon prices (f.o.b. Australia) to surge from US$674/t ($611/st) at [ ] the end of 2005 to beyond US$2,400/t ($2,177/st) by the end of 2011.

Jan 1, 2012

By Lijun Liu, Yingwei Li, Jianhua Liu, Jinhui Peng

"As essential equipment in the metallurgical industry, current air heat exchangers cannot meet the requirements of high temperature heat transfer. In this paper, an energy efficient air heat exchanger, based on accumulation of the heat generated by microwave absorbing materials, is presented according to heat transfer theory and principles of the microwave field. A tubular shaped heat exchanger was designed and built up through temperature-rising curve, and experimental research of microwave high-temperature air heat exchangers was carried out. It was found from experiments that the tubular shaped heat exchanger fabricated using material B could be used for high temperature heat transfer system, and equilibrium temperatures could reach up to 457—485?.IntroductionHeating or cooling of air by heat exchangers is commonly practiced in a wide range of industries including construction, chemical, machinery, textile, printing, and dyeing [1-3]. Generally such heating or cooling of air is achieved in pipe heat exchangers. There are several drawbacks for such heat exchangers, namely, (i) the limitation of temperature to which the pipes can be heated, (ii) tendency to oxidize at high temperature, and (iii) poor strength of metallic pipes at high temperature. These limitations do not allow pipe heat exchangers to be operated at high temperatures [4-6].Microwave heating of inert solids, which are stable at high temperature, is a possible solution to achieve high temperature of the medium in air heat exchangers. It is well-known that microwave heating is an efficient, clean, safe, easy-to-control heating method. Microwave heating utilizes the dielectric and magnetic properties of a material. When microwaves penetrate and spread into the dielectric material, electrons, ions, etc move in the internal electromagnetic field, while the elasticity of inertia and friction impede these movements. This results in a significant thermal effect, increasing the surface temperature rapidly [7-8]. This paper studies mainly design and experimental research of microwave high-temperature air heat exchanger."

Jan 1, 2011

The words ""Uncertainty"" and ""Risk"" pervade every discussion about mining exploration and investment. Perhaps these terms are subjectively understood by industry professionals, but objective portrayal of these concepts outside the industry is a woefully undeveloped science. This paper addresses current industry understanding and practice regarding quantitative risk assessment techniques, and provides examples of the application of three of these techniques. Probabilistic techniques for financial risk assessment are valuable adjuncts to conventional financial analysis, and address a range of issues not assessable by any other means. The value of whole-of-project probabilistic risk assessment is currently debatable for decision-making purposes, but is seen as important as a mechanism to focus attention to the critical issues that ultimately impact on project success. The dissection of project capital into risk and non-risk components provides valuable insights into risk characteristics not readily quantifiable in any other way. This technique also provides a framework for more objective ""what if?"" scenario evaluation and for the capital structure of resource projects. Finally, mechanisms for the valuation of undeveloped reserves are examined, and guidelines suggested. The importance of reliability in production cost estimates is highlighted and the impact of early development on reserve valuations is discussed. The importance of economics throughout all stages of the evaluation process is fundamental.

Jan 1, 1994

By Fidelis T. Suorineni

Rapid drifting enables quicker access to orebodies, higher productivity rates and a resultant reduction in activity costs. Increased advance rates, by examination of the key components (face preparation and drilling, hole loading and blasting, scaling, mucking and support installation) in the development cycle, and optimizing these processes is a high priority for research in the Canadian mining industry. Support installation time alone is typically 36 to 46% of the total development cycle time. A reduction in support installation time or techniques and alternative scaling strategies could result in significant gains in drift development advance rates. Support Staging and hydroscaling within the drift cycle could offer alternative drift development sequences that could reduce the overall cycle time. MIRARCO?s research into the support and hydroscaling processes for rapid drift development also suggests that there are many other factors (e.g. mine ventilation services) that have a significant impact on the rate of advance. These factors should be considered to promote and manage safe and rapid drift development. Constraints to the rapid drift development processes can only be overcome by sound construction management practices. In other words, the goals of rapid drifting can be achieved by the implementation of contractor-type construction management. This paper examines various constraints and processes affecting rapid drift development and draws attention to other factors affecting safe rapid drift development.

Apr 1, 2005

By A Woodley, A N. Danoucaras

In 2012 the Bureau of Meteorology, under the banner of the Water Accounting Standards Board, released the Australian Water Accounting Standard 1 (AWAS 1). This standard has been in development since 2007 with key milestones being the release of the Preliminary Australian Water Accounting Standard in 2009 and the exposure draft of the Australian Water Accounting Standard in 2010. Throughout this period, the Minerals Council of AustraliaÆs Water Accounting Framework has developed concurrently with the Australian standards and the standards have informed elements of the framework. However, the framework is not identical to the standard as the objectives between the two are different. The objective of the Water Accounting Framework is to create consistency in water reporting of the minerals industry and to assist companies reporting to corporate sustainability initiatives. The objective of AWAS 1 is to provide information to water management bodies to facilitate decisions about the allocation of water resources. Companies are to report on an annual basis - not only physical flows of water but contractual requirements to supply and obtain water - regardless of whether the transaction has been fulfilled in the reporting period. In contrast, the Water Accounting Framework only reports on flows that have physically happened. The paper will provide summary information on aspects of AWAS 1 that are most relevant to the minerals industry, show the alignment and differences between AWAS 1 and the Water Accounting Framework and explain how to obtain the information for the AWAS 1 reporting statements.CITATION:Danoucaras, A N and Woodley, A, 2013. Alignment and differences between the Australian Water Accounting Standard and the Water Accounting Framework for the minerals industry, in Proceedings Water in Mining 2013 , pp 85-90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Harvey S. Mudd

WHEN talking about Europe it is well to endeavor to keep politics and economics apart but they have become so intermingled in recent years that the discussion of one topic inevitably leads to the other. Economic influences formerly prevailed over politics but today national and international economies are governed by political forces. Commerce in raw materials, food, and manufactured products is now so restricted by governmental controls that the capacity of the world to produce and to consume, to exchange goods and to pay for them, cannot be gauged by the past or predicted by a multitude of experts. In prewar days there were some yardsticks but today there are none. Thus it is hazardous to make forecasts, for in all fields of human effort the world has been cast upon an uncharted sea.

Jan 1, 1947

By M. J. Ferrante

Relative enthalpies of CuBr from 298.15 to 1,301 K were measured at the Bureau of Mines to provide thermodynamic data needed for the advancement of mineral technology. The temperatures of transition were measured by differential scanning calorimetry (DSC) and the standard enthalpies of transition[ (IlH~r) by drop calorimetry. The combined results gave reversible transitions at 657 K with llH~r= 1.10 kcal/mol, at 741 K with lm~r == 0.51 kcal/mol, and at 759 K with an enthalpy of fusion (AH~) of 1.22 kcal/moL ] An anomalous increase in heat capacity preceded the first crystal transition at 657 K. Tabulated values are listed for the standard relative enthalpy, heat capacity, entropy, and Gibbs energy function from 298.15 to 1,500 K. Standard relative enthalpies are also given in equation form and combined with thermodynamic data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation.

Jan 1, 1984

By J. Wiebmer

The two most important influencers of cost-per-ton in an underground mining machine are its productivity (tons/hour) and its availability-utilization (hours/year). Operating cost and initial price have far less impact. This paper reviews a cost-per-ton sensitivity analysis for underground mining equipment and discusses benchmarks for measuring its performance. The conclusion is that miner-supplier partnerships and the Information Age are the two most significant trends in cost-per-ton reduction.

Jan 1, 1997