Search Documents

By Amos L. Beaty

The oil industry can prosper only if crude production is not excessive. This is true for several reasons. In the first place, the marketing branch of the business is so highly competitive that there is little room for profits in it. There are too many service stations, too many middle men or jobbers, too many refiners eager to press their products upon the market. And the battle is between the strong. If any money is being made in oil today it is by small marketers who buy products from the refining companies and sell on guaranteed margins. In the second place, refineries are overbuilt. There is a large surplus refining capacity. If refined stocks were drawn down they could and would be replenished in short time on short notice. This excessive refining capacity is not serious, however, if the supply of crude is limited to trade requirements. True, it may reflect upon the intelligence of the industry, but if there were a shortage of crude for a few years refining capacities would be readjusted. In the meantime no great harm could result from some idle capacity. It requires no computation to see that refiners could not produce surplus stocks of products from a short supply of crude. I have in mind, of course, the increased yields from cracking. Allowance must be made for that. Still, the picture is the same; less crude is required. I think we can have prosperity in the oil business if too much crude is not produced. A proper limit at this point would be felt all the way down the line. It would slow the refiner and slow the marketer inevitably. Once this constant pressure to make more and sell more is off, operations will be normal and there will be some return on investments. Peices in Relation to Production Potential production at this time is very large, and this condition has existed for many months. As a result the price of crude is low. It is below the average cost of production. Nevertheless, if restraints were withdrawn actual production would immediately increase and the situation would become even worse than it is now. Eventually, of course, the

Jan 1, 1932

By D. P. Wilkinson

There are significant global environmental and supply issues with existing energy paths today . Global emission and fuel regulations, global fuel and power structure, energy security, and cost are driving new technology and non-conventional approaches . Fuel cells will play a significant role in the strategy to effect positive global change, increase fuel efficiency and decrease dependency on traditional fossil fuels. Fuel cells do not require recharging, just refuelling and a wide range of fuels are possible with hydrogen being the most desirable. Technical progress as well as investments in fuel cells for transportation, stationary, portable, and micro fuel cell applications have been dramatic in recent years. The present view is very optimistic for fuel cell power generation and the status is presently at the field trial level, or early commercialization stage, moving into volume commercialization. A number of demonstration programs are in progress worldwide such as the California Fuel Cell Partnership which involves original equipment manufacturers (OEMs), fuel providers, transit authorities, state and government bodies. Fuel cells and a hydrogen infrastructure are key to a long-term solution to global energy issues. Fuel cells will need to be competitive on an economic basis with the established and highly developed internal combustion engine and other forms of power generation There has been significant technical progress in a number of fuel cell areas including power density, transient / dynamic response, multiple fuels, cost potential, reliability and durability. However, significant technology gaps still remain today. This presentation will focus on the status and progress of the fuel cell today, current fuel cell research and development, the challenges going forward, and the future view of the fuel cell and it's impact on global energy issues.

Jan 1, 2005

By Katzer R. Klimpel, J. Sewell

Dr. Roussey Roussev The use of chemical additives on grinding is of significant importance considering the high energy consumption of grinding processes. My research indicates that the dispersant approach explains the effects, in this particular case of wet grinding. Further, the dispersant approach combined with torque measurements give the possibility of clarifying the mechanisms involved when using grinding aids. I find the conclusions derived from the data obtained to be correct and useful for grinding. In general, I agree with the explanations. However, I would like to discuss several additional points that I consider to be important, and in the same time to mention some of my own results from investigations similar to those presented in the study under discussion. The "bed volume concept" and the change of slurry viscosity explain adequately the data plotted on fig. 3, in conjunction with Figs. 1 and 2. However, the significant increase of the average torque in the case of 83% solid with XFS-4272 introduces the necessity of establishing the optimum of percent solid when dispersant is used. For example, the optimum percent of solid for different materials varies. One of the reasons is the material's mass density. On the other hand, it is necessary to determine the concentration of the chemical used. Because of this, it would be interesting to know how the cited concentration was selected. The supportive discussion and verification by Dr. Roussev, with results similar to that of the paper, is appreciated. I will try to answer the additional questions he has raised. To begin with, the mill was fitted with six lifters of approximately one-quarter inch height. There has been extensive lab and plant level work to understand downstream influences of using dispersants like XFS-4272*. In sulfide ore processing, which is the area in which most industrial scale testing has been performed with this approach, neutral to positive influences have been observed. For example, positive effects (e.g., increased recovery) have been noticed in flotation operations involving ores that have a tendency to produce excessive slimes upon grinding. (1) Also, the use of a dispersant has been shown to demonstrate a positive influence on classification by improving the sharpness of separation and preventing a decrease in d50 value that usually accompanies increasing flow rates to classifiers.(2) The biggest potential downstream problem is in thickening, which at the dosages involved, has not been a problem in plant scale usage. The commercial price of dispersants like XFS-4272 is quite variable depending on source, concentration, etc, but a typical cost of XFS-4272 to achieve a 10% increase in throughput in industrial mills has been between 20 and 35- US per ton of feed ore (1981).

Jan 12, 1982

By Edward H. Robie

MANY engineers currently are working harder than usual, in part because of the demands being made upon them for increased production in the war effort, and in part because engineers are in short supply so that there is more to do for those who are available. In some instances the question has come up as to what additional payment, if any, should properly be made for overtime work, and to what extent is such payment legally permitted under the rules of the Salary Stabilization Board. Most engineers employed in an executive, administrative, or outside salesman capacity are not paid for overtime. They are paid for doing a job instead of for the hours they put in, and are free to do all the unpaid home work they feel they should do after dinner, as well as to do a bit of thinking and worrying during wakeful hours in bed. But engineers employed in a strictly professional capacity normally have standard office hours. Some employers pay for overtime and some don't. Their practice as it existed on Jan. 25, 1951 may be continued. In the absence of such practice at that time, the Salary Stabilization Board says that the engineer may now receive additional compensation up to his straight-time rate for an extended work week. No formal approval of the Board is required. "A professional engineer," in the mind of the Board, "is a person employed in a professional capacity, who, by reason of his special knowledge of the mathematical and physical sciences and the principles and methods of engineering analysis and design, acquired by professional education and practical experience, is qualified to practice engineering." Inducted Engineers A letter from a young man just inducted into the service and fearful that his engineering training is not going to be utilized reached us last week from Fort Riley, Kan. The AIME, cooperating with the other Founder Societies, is doing what it can, through the Engineering Manpower Commission, to see that engineers are not being wasted in the military establishment. So we passed this young man's letter along to T. A. Marshall Jr., executive secretary of that Commission. Mr. Marshall tells us that the normal procedure now being followed by the Army in handling Selective Service inductees is to have them first complete 16 weeks of basic training before assignment to specialized categories. During that time they are classified. If one has an engineering degree he should be classified as scientific and engineering personnel at the end of the basic training period. He should then be transferred to a technical detachment and assigned an MOS (Military Occupational Specialties) reflecting his education. If a young man is looking for a commission, it might be added that the current policy in the Army is to transfer to OCS (Officer Candidate School) applicants for commissions in the infantry only. The local unit commander can give information on this point, based upon the aptitude shown in tests. In view of the current shortage of engineers, it is believed that a young man should seriously consider remaining in enlisted status unless he can obtain a commission in a branch of the service that can make full use of his technical skills. His work may thus be more to his liking even if his uniform is not. New York or Atlantic City? In which place is it preferable to hold the annual meeting of a professional society like the AIME-New York or Atlantic City? That is, a winter meeting. The American Society of Mechanical Engineers has held its recent meetings at Atlantic City, with increasing attendance and satisfaction. The American Institute of Chemical Engineers chose Atlantic City for its recent December annual meeting. Only twice has the AIME ever met in this famous seashore resort: in 1898 and 1904. Chief advantages of going to Atlantic City over New York are that technical sessions are better attended, there being little else to do there in Winter; the cost to members is less, and hotel facilities are better adapted to a large meeting. As to cost, take a banquet, for instance. The Chalfonte-Haddon Hall, which caters especially to winter conventions, charges about $7 for a banquet dinner of standard quality. A similar dinner at the Statler in New York would cost about $8.50, and about $10.50 at the Waldorf-Astoria. (The charge for tickets is somewhat greater than this because of the cost of music, programs, flowers, and other incidentals.) Rooms, too, are somewhat less at Atlantic City, two in a room being accommodated for about $7 per day each, compared with $7 to $10 at a headquarters hotel in New York. On the other hand, AIME headquarters is put to some extra expense for staff travel, food and lodging, and members living in New York and environs are forced to pay a hotel bill. New York, of course, has more varied amusements to offer, plenty of big stores, and the glamour of a big city. The choice may be discussed at the forthcoming meeting in New York. In the meantime if any reader cares to express an opinion one way or the other we shall be glad to hear it. College Scholarships Most parents of children in the later stages of high school find it necessary to give some consideration to the cost of a college education. Although salaries have increased substantially it seems that the cost of the necessities of life, such as food, housing, and maintaining the family automobile, have gone up even more, so the problem of financing the children's education is as acute as ever. Many overlook the possibility of scholarships, or feel that only a student at or near the top of his class has a chance to get one. As a matter of fact, close to 150,000 scholarships and more than 15,000 fellowships, worth some $42,000,000, are available in 1200 American colleges and universities. Those who are interested should send 55¢ to the Superintendent of Documents, Government Printing Office, Washington 25, D. C. for a 248-page publication just issued by the U. S. Office of Education, entitled "Scholarships and Fellowships Available at Institutions of Higher Education."

Jan 1, 1952

By Jilai Xue

Industrial wastes containing 30-50 wt.% Al2O3 and 40-60 wt.% SiO2 may serve as an alternative resource for producing Al-Si alloys. Various raw materials such as used refractory materials from metallurgical furnaces, coal fly ash, andalusite residues, and so on were tested in laboratory to produce Al-Si alloys using carbon-thermal reduction process. A mixture of anthracite and petroleum coke was used as reducing agent. One of the most important operations was to prepare the briquettes made of different raw materials with varying contents of Al2O3 and SiO2. The effects of briquette property, A/S ratio (mass ratio of Al2O3 and SiO2), the amount of carbon reducing agent, on the reduction process and the resulting metals were investigated. The results are useful for development of an alternative technology for Al-Si alloy production, which has the potential application in recycling metals from industrial wastes containing Al2O3 and SiO2.

Jan 1, 2010

By Dave Bulled

"This paper describes the design of an SABC grinding circuit using CEET technology applied to grindability data produced from testing 100 samples and distributed across the blocks of a mine plan using a geostatistical approach. The data distribution required the identification of the location of the sample points and a geological plan of the 130 million ton Ruby Creek orebody together with a mine plan of about 11000 blocks to be mined during the proposed 18 year life of the mine. The mill design was then made with consideration for the estimated hardness of each block in terms of both SAG and Ball milling with allowance for annual periods when the ore is harder to grind. Operating specifications were selected to achieve an optimum of capital and operating costs through use of the CEET program. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the hardness estimate of each block of ore in the mine plan. The final design could then include a quantification of risk and determination of safety factors based on the accuracy of block hardness estimates and CEET model fitting.INTRODUCTIONThe traditional approach to plant design involves the extensive testing of a single large composite sample or a small number of composite samples that are reputed to represent the ore body. It is accepted that the tests used can accurately measure in the laboratory the grindability of the sample by a process representing that to be used in the plant. The size of equipment required to achieve a specified throughput and product size is then calculated from one of a variety of models that have been developed by metallurgists over years of trial and error. Since these tests and models are tried and tested, they are accepted as reasonably precise; however during the operation of the resulting plant the design is sometimes found to be inadequate. It is then suspected that the flaw in the design process lies in the samples not being sufficiently representative of the ore body, since using only a single or small number of composite samples does not recognize the variability of the hardness of the ore, nor does it allow for the lack of precision in the hardness value used in the design.This paper outlines a design procedure suited to an orebody that is described by a geostatistical analysis of a reasonably large number of small samples of drill core. The analysis required the identification of the location of the sample points and a geological plan of the orebody, together with a mine plan of the blocks to be mined during the proposed life of the mine. The mill design was then made using the estimated hardness of each individual block with an allowance for annual fluctuations in the grindability of the ore. The geostatistical analysis assigned a statistical error to the hardness estimates of blocks and of each production year such that the final design included risk estimates and safety factors based on the possible errors that arise from having a limited amount of sample data (Kosick et al. 2002)."

Jan 1, 2007

By Schlanger H. P

A theoretical model for gas outbursts in underground coal mines is as follows. An outburst is the structural failure ofcoal due to excess stress resulting from body forces caused by gas pressure gradients. These body forces influence the stability of a mine face in the same manner that gravitational body forces affect the stability of the roof of a mine. The magnitude ofthese body forces can be appreciated when it is realized that for an average density coal, the gravitational body force is equal in magnitude to the force from a gas flow with a pressure gradient of 14 kPa m-I. Gas pressure gradients and the resultant stresses within a seam can be calculated with numerical methods. Thus, providing the necessary parameters can be measured or estimated, in principle the theory can be applied to compare the outburst risk of various mining arrangements.

Jan 1, 1985

By S Hapugoda, J R. Manuel, M J. Peterson

Microindentation testing using the square–pyramid–shaped Vickers indenter is a well-established technique to determine the microhardness of minerals and materials. However there is a paucity of published microhardness data from Fe ore samples. It is acknowledged that an iron ore’s particle mineralogy and texture is critical to its processing properties, and it is therefore considered that the microhardness of different mineralogical/textural types may also relate to these properties. Mineral microhardness potentially provides inputs to the modelling of breakage characteristics during comminution, as well as the relationship between mineral chemistry and microhardness, and mineral microporosity and microhardness. Microhardness can be determined as single crystal microhardness, for more coarsely microcrystalline samples, or as ‘aggregate microhardness’ for cryptocrystalline or finely microcrystalline samples.Variations in the texture and mineral chemistry of common Fe ore minerals (eg martite and microplaty hematite, ochreous and vitreous goethite etc) are well established and this study provides microhardness data on different textural forms of Fe (oxyhydr)oxides from a variety of different Fe ore deposits. The data indicated that in general, the mineral grain size, microporosity and texture were the main influences on Fe (oxyhydr)oxide microhardness. There were no apparent systematic variations between microhardness and minor element mineral chemistry, with the possible exception of Al content in goethite (for goethites with Al content >0.5 wt per cent), and for goethite total element contents >90 wt per cent (determined by electron probe microanalysis, EPMA). Higher Al concentrations and lower total element concentrations in goethite EPMA analyses correlated with lower goethite microhardness. Microporosity and grain size were more important than texture to hematite microhardness. Different textural forms of dense hematite (eg martite, recrystallised interlocking hematite and specular hematite) with similar grain size exhibited comparable microhardness. Microhardness values for hematite and hydrohematite with little or no evident microporosity were also similar, whereas more porous forms of martite, microplaty hematite or hydrohematite exhibited lower microhardness.CITATION:Peterson, M J, Manuel, J R and Hapugoda, S, 2017. Microhardness testing of hematite-goethite Fe ores – implications for their textural characterisation and geometallurgy, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By S. Kitamura

In recent years, the amount of ferritic stainless steel production has increased. However, the rust formation by the salt spray test was pointed out in the past. At the centre of the circular rust zone, pitting corrosion where water-soluble nonmetallic inclusions were embedded was observed. These inclusions originated from the suspended refining slag and consisted of multi-phase oxides and sulphides. By the experiments and thermodynamic consideration of the water-solubility, not only CaO or CaS, but also lime rich calcium-aluminates or calcium-silicates have shown large water-solubility. The composition of oxide phase in the inclusions was almost the same among the samples from molten steel, slab, or cold rolled sheet. On the contrary, CaS was clearly observed around the oxide in the sample of cold rolled sheet, although it was not found in the molten steel or slab samples. The enrichment of sulphur occurred from the desulphurization reaction of the suspended slag particles in the molten steel and also occurred from the diffusion of sulphur to the oxide inclusions during the heating of the slab. The optimization of refining slag composition has lead to produce the ferritic stainless steel without rust formation. Keywords: stainless steel, rust, calcium aluminates, calcium sulphides, water-solubility, refining slag, composition control of inclusions.

By Chao Du, Xiaohui Ning, Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao

"TiCxOl-x solid solutions were synthesized by sintering a mixture of titanium carbide and titanium monoxide at 1600 °C. The corresponding structures and morphologies of the TiCxOl-x solid solutions were characterized by XRD and SEM. A series of tests has been performed on the electrochemical dissolution behavior of TiCxOl-x solid solutions in NaCl-KCl molten salt. The influences of synthesis time and electrokinetic parameters on the anodic dissolution behavior were also investigated. The results showed that TiCxOl-x solid solutions can dissolve as Tin+ into alkali chloride melt. Titanium ion species dissolved from TiCxOl-x solid solutions changes between Ti2+ and Ti3+ depending on the applied potential. The tail gas on the anode was monitored by a mass spectrometer. It was found the synthesis time significantly affects the components of the anodic gas.IntroductionTitanium and titanium alloys have been desired greatly because of their many uses. The critical factor that restricts the range of uses for Ti is its high cost of extraction. The primary titanium metal, sponge titanium, is still produced industrially worldwide by a process invented by Dr. Kroll in the 1940s[1] •Since the early 1970s, the research focus of the titanium industry has been directed towards developing a continuous process to produce high purity titanium at low cost. [2-10] Of the many alternative methods that have previously been investigated, the electrolytic process has been considered a promising method for titanium metallurgy [4-10]. Recently, several electrolysis and related methods such as the PFC-Cambridge process[11-15], calciothermic reduction[16-18], USTB [19,20] and MER[21] process were extensively investigated.The USTB process is a new approach where the pure titanium can be directly obtained by the electrolysis with an anode of titanium oxycarbide in molten salts[19, 20]. The titanium oxycarbide was produced by carbothermal reduction of titanium dioxide under vacuum at a temperature"

Jan 1, 2011

By Gerald M. Ellis

ntroduction As the gold mining industry continues to develop in the Dominican Republic and Haiti, more deposits will undoubtedly be discovered that will be amenable to development. The Pueblo Viejo gold mine is currently in operation in the Dominican Republic. It has become an important component of that country's economy. Pueblo Viejo output is important to the government as a foreign currency earner. It is also said to be among the world's more successful gold mines. But, while Pueblo Viejo is successful, no other major gold discoveries have been made in recent years. Therefore, alluvial deposits of gold have caught the attention of geologists on the Island of Hispaniola. In the past four years, exploration and investigation of alluvial deposits have been initiated in both the Dominican Republic and Haiti. This type of activity is expected to continue over the next few years. Alluvial gold mining is rudimentary gold washing, done mostly by farmers. It is an old tradition, dating back at least 100 years, and is done by small, independent, or community farming villages in the mountains and plains of the Dominican Republic. Investigations in the DR Recently, alluvial gold investigations have been undertaken in well known locations of the Dominican Republic. One is in the Villa Altagracia area. Here, the terraces and gravels of the Haina River basin were examined, test-pitted, and assayed by Minera Altagracia, a local Dominican mining group. Results led to a new investigation by the state-owned Rosario Dominicana (RD), the company that mines the gold at Pueblo Viejo. Rosario tested areas previously investigated by Minera Altagracia. RD could not define the type of concentration that could justify an industrial-scale type of exploitation. The Haina River placers are located in the flats and valleys of Central Dominican Republic. They are classified as small-scale type of operations where local cooperatives can do the traditional gold washing. It is not now considered a dredgable project for a mining company. The next alluvial gold investigation was undertaken by the Dominican Department of Mines and others in an area of some 700 km2 (270 sq miles) in the northeast near Miches. Farmers have been washing gold in streams and excavating pits in various areas, particularly La Mina and have made a living. Government geologists panned several hundred streams and river tributaries. They also washed material from deep excavations. The results, however, were negative insofar as locating alluvial gold concentrations suitable for large-scale or industrial-scale exploitation. The most favorable locations were the terraces along the Jayán and Cuarón Rivers in the area of Miches. But the grade od concentration is poor. Actually, only traces of gold were found in these

Jan 8, 1986

By Hazal Melis Aytac, Lana Alagha, Fardis Nakhaei

Gallium (Ga) and Germanium (Ge) are essential strategic elements that are extensively used as semiconductors in many technological fields. Owing to their essential uses and supply disruption, Ga and Ge are deemed critical by the U.S. They are typically found as substitutions or inclusions in zinc minerals. However, their distributions within zinc minerals are not well understood. To address this, trace element and mineralogy analyses of representative samples obtained from an old high-zinc-grade tailing were performed using various qualitative and quantitative techniques. These techniques included Inductively Coupled Plasma Mass Spectrometry (ICP-MS), Tescan Integrated Mineralogical Analysis (TIMA) with Scanning Electron Microscopy (SEM) and X-ray Diffraction (XRD). Moreover, bench-scale froth flotation tests were conducted to enrich zinc minerals, the major hosts of Ga and Ge, using PAX as a collector, Na2S as a sulfidizer, Pb(NO3)2 as an activator, and MIBC as a frother. Comprehensive characterization analyses of the flotation products showed significant enrichment of Zn, Ga and Ge in the flotation concentrates.

Feb 1, 2025

By Kostas Fytas

Canada still remains today a strong resource nation with a huge geological potential. Canada ranks among the top five leading countries in the production of 15 major minerals. Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage production. It is estimated that across Canada there are a few thousand abandoned mine sites as a result of the last fifty years of mining. Most of these sites are acid producing presenting a serious threat to the environment. It has been estimated that the cost of stabilizing and reclaiming these sites across Canada will be over $5 billion over the next twenty years. Current practices for decommissioning acid producing sites are water covers (flooding), dry covers, revegetation and treatment of the acid effluents. This paper presents the technical and legal issues of mine closure and reclamation in Canada. The methods used in the revegetation of acid producing mine sites is also presented This paper also reviews the financial guarantee requirements for mine closure by the provincial legislations in Canada. A case study of stabilizing and reclaiming a sulphide tailings area in the Sudbury region is presented. It illustrates the challenges facing the Canadian Government and the mining companies in restoring and revegetating the closed and abandoned mine sites across Canada.

Jan 1, 2002

By D. R. Dollnar

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

Jan 1, 2002

By H. Le Chatelier

SILICA brick are indispensable in the manufacture of steel because they alone are able to withstand the high temperature of regenerative furnaces. All attempts to replace silica brick by other refractory materials for this purpose have failed, but the reason for this failure has remained obscure; we shall give an explanation later in this paper. Before the war, silica brick employed in France came principally from abroad, for which reason, since the beginning of hostilities, certain French steel works have been seriously handicapped. Our attention was first directed to the question by M. Bred, Engineer of the Teil Works. With him, we began certain investigations, at first using our laboratory and the furnaces of neighboring steel works. The larger part of our experiments, however, have been made in the laboratory of the Faculty of Sciences at the Sorbonne. For the heating of our samples, we are deeply obliged to MM. Charpy, Yeatmann and Guérineau. In undertaking these studies, our first aim has been to render assistance to French industry, by indicating, as precisely as possible, the necessary conditions for the manufacture of high-grade brick; but at the same time we have intended to give an example of the manner in which scientific methods may be put to practical application in the solution of industrial problems. Although our work has been confined to samples of only a few grams, we are nevertheless convinced that our information can be directly utilized by brick-works of which the output is measured in thousands of tons

Jan 9, 1918

By F. Patisson

One of the major issues with multiparticle reactors is to handle their multiscale aspect. For modeling, it usually comes to coupling a reactor model (describing the phenomena at the macroscopic scale) with a so-called grain model (simulating the behavior of a single grain or a particle). An interesting approach proposed by H.Y. Sohn (1978) is to use the law of additive reaction times in order to calculate, approximately but analytically, the reaction rate of a particle in the reactor model. Its great advantage, compared to a numerical grain model, is to drastically reduce the computation time, particularly in the case of complex reactor models. This is the approach we retained for modeling the moving bed furnace, a counter-current gas-solid reactor used in the nuclear fuel-making route for producing uranium tetrafluoride from uranium trioxide. The numerical model we developed is 2-dimensional, steady-state and based on the finite volume method. It describes solid and gas flow, convective, conductive and radiative heat transfers, and six chemical reactions involved in the process. The law of additive reaction times is used to calculate analytically the rate of the three principal gas-solid reactions at every discrete point in the reactor. We have demonstrated the validity of this approach by comparing its results with those calculated from a numerical grain model. Also detailed in the paper are the main results of the moving bed furnace model itself and the possibilities of optimizing the process revealed by the calculations.

Jan 1, 2006

RAYMOND M. Howe (author's reply to discussion*).-Dr. Unger states that magnesite will hardly supersede dolomite in fettling after a heat; that it is hard to believe a slag composed of oxide of iron containing about 6 per cent. of phosphorus is the active corroding, agent in a boil in a furnace; and that boiling cannot be said to be the result of the chemical action of a high-phosphorus slag on a basic bottom. These are well-established facts that no one would venture to question. The authors were misinterpreted in the statement that "in the summary, it is claimed that magnesite low in lime, or of greatest purity, ranks first in resistance to slaking," etc. On the contrary, the position has been taken throughout that while a low lime content is advantageous, the presence of several per cent. of iron oxide (an impurity), is necessary in order to confer the proper bonding and sintering properties in dead-burned grain magnesite to be used for furnace hearths. We cannot subscribe to the view that pure magnesia is no better fitted for a refractory than pure lime,' nor that the pure natural varieties of magnesite; such as Grecian or Washington, must necessarily be burned with silica and oxide of iron to produce a satisfactory material. On a small scale, pure magnesia has been satisfactorily used as a refractory in the form of crucibles. In the production of dead-burned grain magnesite from the Grecian or Washington mineral, iron oxide is added but the addition of silica is neither customary nor desirable. It is possible to manufacture brick of good quality from both the Grecian and the Washington material without adding either silica or iron oxide, providing they are burned at a sufficiently high temperature. This is regularly done on a commercial scale both in America and abroad when brick of. exceptionally high refractoriness or special purity are desired. The following analysis is of an English brick of Grecian magnesite which is extremely low in all impurities.1

Jan 6, 1919

By D. Norman, D. J. Hughes, R. Dashwood, I. McGregor, N. D. Raath

"This paper develops a methodology for predicting spot weld fractures in automotive boron steel grades, such that fracture modes can be predicted accurately in a vehicle or sub-assembly structure. To achieve this, it was necessary to understand the range of complex fracture modes observed in boron steel spot welds and how these are linked to the Heat Affected Zone (HAZ) microstructures and hardness distributions and residual stress.Material data for the HAZ was extracted by simulating the spot welding process using a Gleeble machine; achieving specific weld microstructure in a larger volume which was used in destructive testing. Neutron diffraction was employed to accurately characterize the post-weld residual stresses found inside the weld. The constitutive relations of specific areas in the HAZ where fracture is thought to occur is being incorporated into finite element software to improve fracture prediction of boron steel welds.IntroductionWith the drive for light-weighting and improving passenger safety, lighter and stronger materials are being continuously sought in the automotive industry. The application of boron steel in the Body-In-White (BIW) meets both these criteria by down-gauging thickness of the steel and increasing the strength. As an example, when applied to crash-relevant areas in cars, components have an ultimate tensile strength of 1500 MPa, minimum springback and reduced sheet thickness.To achieve high strength and low springback, boron steel components must be formed and hardened at the same time. This is typically achieved by austenitizing the steel around 900 °C and simultaneously quenching and forming, usually with a hydraulic press and tool-set. Trace amounts of boron, typically 0.005wt%, increase the hardenability of the steel dramatically. This is attributed to the grain boundary segregation of boron, which hinders the formation of ferrite during cooling and forces the transformation of austenite to martensite at high cooling rates, a minimum of25 °C/s."

Jan 1, 2013

By Hugh Jones

Mine planners are challenged to hold two seemingly opposing objectives: maximizing the mine?s operational efficiency while minimizing post-closure impacts. One of the most effective approaches to meet these objectives is to plan for mine closure from the start. Mine closure is typically viewed as the process that happens in the period of time when the operational stage of a mine is ending and the final decommissioning and mine rehabilitation is being undertaken. In reality, it is a continuous series of activities that begins with preplanning prior to the project?s design and construction and ends when long-term site stability is achieved and a self-sustaining ecosystem is established. Putting this model into practice as early as possible can significantly reduce the financial burden of mine closure and rehabilitation.

Jan 1, 2011

By B. Galy, L. Giraud

"This paper compares Canadian provincial mining safety regulations regarding the use and testing of cage safety catches, including a brief history and evolution. Regulations are similar across provinces, with only slight variations. Currently, the “Ontario-type” safety dog is the most commonly used safety catch in Canada. Performance estimation of the compensation mechanism for different safety-dog shapes and tooth angles show this shape works well and has consistent braking results, but the best efficiency is obtained for initial tooth angles greater than 10°. Miner safety is questionable for lightly loaded cages, an issue that should be addressed technically and legislatively.RÉSUMÉ Le présent article compare les diverses réglementations de sécurité minière concernant les parachutes des cages dans les provinces canadiennes ainsi que les essais qu’ils doivent subir. Il semble que les réglementations soient semblables à travers les provinces avec quelques légères différences ou divergences. Un bref historique des parachutes et de leur évolution est présenté. De nos jours, le parachute de « type Ontario » est le plus fréquemment employé à travers le Canada et il présente des résultats de freinage uniformes. Une estimation de la performance du mécanisme de compensation pour les diverses formes de taquets de sécurité et les divers angles des dents montre que cette géométrie fonctionne bien; cependant, la meilleure efficacité est obtenue pour des angles de dents supérieurs à 10°. La sécurité des mineurs est mise en jeu pour des cages faiblement chargées et ce point devrait être traité du point de vue technique et du point de vue législatif."

Jan 1, 2016