Search Documents

Continuing with the effort of providing new and more effective exploration methods to the mining industry, where direct methods (drilling, cross-cutting, etc.) are not applicable, either for logistical or environmental reasons or because they are costly and sometimes ineffective, we present here a new seismic technique based on full wave recording of 3-D channel waves generated within the coal seam across a longwall. In the past two years we reported the application on In-Seam High Resolution Seismic Reflection (ISHRSR) and In-Seam Seismic Tomography (ISST) to map non-coal inclusions that disrupt the coal seam continuity. In the present paper we present a 3-D In-Seam Seismic Tomography (3-DTSST) method using 3-D channel waves recorded by three component high resolution geophones. The method allows to distinguish longitudinal and transversal components of the channel waves, similar to the spheroidal and toroidal modes for the free oscillations of the earth. The recording of these waves allows a more complete analysis of the free modal vibrations of channel waves, permitting a more complete inversion of the structure of the coal seam through which they travel. The full wave analysis provides additional insights of the detailed coal structure for larger, distances than for the ones previously reported using the one dimensional method. The refinement of the inversion software is also a contribution towards the better definition of the coal seam geometry and structures disturbing them such as sandstone channels, sandstone rolls, partings, mine voids, faults, fractures, etc. The method is illustrated with three case studies where subsequent mining revealed the virtues and limitations. The first example deals with the problem of mapping mine works in one side of a longwall panel which geometry is well known, to verify its applicability to map old mine works. The second example deals with a sandstone body that partially scoured the coal seam withing a longwall panel. The third shows an application of the method to map roof conditions in a longwall panel where this problem critically affected production scheduling and costs

Jan 1, 1996

By R. L. Virta

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue. Thank you to the industrial minerals annual review editor, to the technical committees chair and vice-chair, and to the authors of the individual commodity profiles. Jim Norman, member SME, of GeoTrans Inc., is the industrial minerals annual review editor. Abani Samal, member SME, of Pincock Allen & Holt, is chair of the industrial minerals technical committees. Technical committee vice chairs include: ? Abani Samal, member SME, of Pincock Allen & Holt, agricultural minerals. ? Aaron McMahon member SME, of Pincock Allen & Holt, ceramics and refractories ? Bradley S. Van Gosen, member SME, of the U.S. Geological Survey, chemical raw materials. ? Mark Zdunczyk, member SME, of Continental Placer Inc., construction materials. ? Jerry Gauntt, member SME, of Marston, fillers and pigments. ? Michael Cheshire, member SME, of Indiana University, sorbents, filters and process aids. ? Candace Trimble, Oil-Dri Corp. of America, specialty minerals. Their help makes possible this June industrial miner-als issue. On behalf of ME readers, the editors thank them. Ball Clay Four companies ? H.C. Spinks Clay (owned by Lhoist Group), Kentucky-Tennessee Clay (owned by Imerys Group), Old Hickory Clay, and Unimin Corp. ? mined ball clay in four states in 2008. Production, on the basis of preliminary data, was 964 kt (1.1 millon st) with an estimated value of $45.3 million. That was a 10- percent decrease in tonnage from 1.07 Mt (1.2 mil-lion st) with a value of $49.2 million that was produced in 2007. Tennessee was the leading producer state with 63 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 73 percent of production was airfloat, 16 percent was crude and 11 percent was water-slurried.

Jan 1, 2009

By M. Polat, S. Chander

Many models have been suggested in the past to obtain a satisfactory fit to flotation data. Of these, first-order kinetics models with a distribution of flotation rate constants are most common. A serious limitation of these models is that type of the distribution must be pre-supposed. Methods to overcome this limitation are discussed and a procedure is suggested for estimating the 'actual' distribution of flotation rate constants. It is demonstrated that the classical first-order model fits the data well when applied to coal flotation in narrow size-specific gravity intervals. When applied to material which is fractionated on the basis of size alone, the use of three parameter models, which were modified from their two parameter analogs such as rectangular, sinusoidal, and triangular, gave most reliable results.

Jan 1, 1995

By Fred D. Gustafson

With the postwar emergency for new housing and for new industrial buildings, much research has been done on lightweight aggregates for use in concrete and plaster. The trend toward lighter weight aggregates to relieve the dead load on the higher, steel framework buildings started toward the end of the last century. Progressively the requirements became more stringent, crushed bank slag, weighing 80 lb per cu ft as compared to 100 lb for crushed rock, was supplemented in some sections by foamed slags and expanded shales weighing from 40 to 60 lb per cu ft. In other sections cinders were used weighing from 40 to 50 lb, including sand. Sections favored with more recent vulcanism turned to pumice weighing from 30 to 60 lb, whereas other localities made use of diatomite, from 28 to 40 lb. Exfoliated vermiculite weighing from only 6 to 10 lb per cu ft came into use. As the search for lighter weights in aggregates continued so did the search for other desirable properties such as nailability, ease of cutting or channeling, and good insulation to both sound and heat. This search eventually led to a widespread interest in the expansion of perlite, or similar volcanic glasses, with the result that in 1946, the Office of the Housing Expediter' listed eleven firms reporting the operation of processing plants either on pilot or commercial scale producing aggregates weighing from 2 to 16 lb per cu ft. Geology Perlite is one of the large family of rocks originating from a granitic or acidic magma and generally has a "rhyolitic composition with a marked perlitic structure."² The name "perlite" is a derivation from "perlstein" originally given "to certain glassy rocks (hyaloliparites, hyalo-rhyolites) with numerous concentric cracks, from the fancied resemblance of broken out fragments to pearls."3 The cause of the perlitic texture is somewhat controversial. Johannsen attributes the texture to strain set up in the glass by cooling and describes the finding of peculiar, glassy balls, called marekanite, more or less rounded and showing concave indentations, which may be left when perlite is broken. Frank Rutley, on the other hand, in 1881, while working on vitreous rocks from Montana, observed that there was incipient or partially started crystallization with segregation of water toward the un-crystallized portion in all specimens of perlite examined. Further he observed evidence of strain around focii of crystallization to which he ascribed the development of the spherical cracking which gives the rock its perlitic texture.4 Widespread over the western and southwestern United States where Tertiary vulcanism is exposed, perlite commonly is associated with andesitic, basaltic, and rhyolitic lavas with inter-bedded tuffs and ash of Eocene age although some deposits are associated with rocks assigned to the Pliocene age.5, 6 n nearly all cases the perlite overlies water laid tuff beds or agglomerates or breccias of explosive nature, an outstanding exception being the occurrence of perlite as the chilled selvage of andesite intrusions.7'8 Available chemical analyses of per-lites from the western and southwestern United States indicate that they are varieties of leucorhyolites rather than of normal rhyolites, leucorhyolites having less than 5 pct of dark minerals, normal rhyolites having more than 5 pct. This conforms with Johannsen's observation that leucorhyolites are the prevailing kind in North America.9 Tables 1 and 2 give

Jan 1, 1950

The area between Merrygoen and Digilah is located on a structural high that separates the Sydney Basin from the Great Artesian Basin, and hence the stratigraphic succession of younger rocks overlying the basement is relatively thin. The stratigraphy is briefly described and it is shown that fluvial sedimentation prevailed from Upper Permian through to Middle Jurassic times. Flint clays occur in the Permian, Triassic and Jurassic but only those in the Jurassic appear to have commercial value at present. The chemical, mineralogical, and physical properties of the flint clays are discussed.

Jan 1, 1973

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

Participating Scholarship Colleges and Universities 134 AmerCable, Inc 144 Andalex Resources, Inc 118 ARCO Coal Company 148 Behre Dolbear & Company, Inc 101 Coastal States Energy Company 100 Commercial Testing & Engineering Company 88 Crane & Hoist Sales Inc 121 Cyprus Amax Minerals Company 115 Dakota Coal Company DriltechInc 135 Empire Machinery Company 94 Energy West Mining Company 122 GH Hensley Industries 126. 127 Hitachi Construction Machinery (America) Corp. 12 Ingersoll-Rand Company 141 Jennmar Corporation 142 Joy Mining Machinery - A Harnischfeger Industries Company 104 K & P Sales Engineers, Inc 114 Kennametal Inc 95 Kennecott Energy Company 133 Kerr-McGee Coal Corporation 96 LeTourneau, Inc 145 Long-Airdox Company 112 Magnum Metals, Inc 138 McLanahan Corporation 129 Mine Technik America 124 Morrison Knudsen Corporation 97 National Mining Association 98 Nielsons,Inc 136 The North American Coal Corporation 130 Northwestern Resources Company 125 O&K Orenstein & Koppel, Inc 14 Peabody Western Coal Co 131 Phillips Machine Service, Inc. 13 Pincock Allen & Holt 120 Powder River Coal Company 107 Ramsey Technology, Inc 119 Rust Tractor Company 90 Salt River Project 91 Savage Industries Inc 89 Sheraton Steamboat Resort and Conference Center 111 Stamler Corporation (An Oldenburg Group Company) 117 Tamarron Hilton Resort 137 TerraMatrix Inc 139 TIC (The Industrial Company of Wyoming, Inc.) 99 Trapper Mining Inc 106 Wagner Equipment Company 116 Western Energy Company 105 Wheeler Machinery Company 128

Jan 1, 1996

By John Nell, Paul den Hoed

Carbochlorination tests were conducted with matched particle-size fractions of rutile, ilmenite and high-titania slag in a small bubbling fluidized-bed reactor. The effects of temperature, the type and proportion of solid reductant in the charge, and the fraction of Cl2 in the fluidizing gas were investigated. Tests confirm the need for solid carbon in the bed if chlorination is to run at high rates. With solid carbon in the bed, CO supplied with the fluidizing gas does not increase significantly the degree of chlorination after 75 minutes. Ilmenite is chlorinated more quickly than titania slag, which in turn is chlorinated more quickly than rutile. Rates of chlorination at 1100°C and 1000°C are much the same and significantly higher than at 900°C. Chlorination is associated with significant increases in particle porosity (even for rutile), which is brought about by the rapid initial chlorination of FeO and MnO (in ilmenite and slag) and (it is argued) by the chlorination of Ti2O3 which forms at high-energy surface sites. A reaction mechanism is presented; where possible, its validity is demonstrated by the support of empirical observations.

Jan 1, 2003

By Watson D. F

P S B Stewart has rightly pointed to a possible obscurity in our paper on drilling patterns, viz. in comparing the improvement of a triangular drilling pattern over a square one, we used percentage improvements without always making clear their base. We hope, however, that other readers, like Stewart, have been able to understand the particular meaning from the context.Although different methods of estimation of an ore deposit will have different local bias (Philip and Watson, 1985), the critical relationship affecting the reliability of estimation of an unsampled location is the scale of local variation of the variable being estimated in comparison with the density and isotropy of sampling. This relationship overrides all other considerations.

Jan 1, 1985

By Arash Khosravifar, Matt Steffan

An expansion of the City of Klamath Falls Wastewater Treatment plant required geotechnical seismic hazard evaluations and deep foundation design. The site is located on the shore of Lake Ewauna and is underlain by diatom rich lake deposits. Diatomaceous soils exhibit unique engineering properties that are not well understood. Cyclic Direct Simple Shear (CDSS) testing was performed on three undisturbed samples to evaluate cyclic and post-cyclic properties of the diatomaceous soils. Results from the CDSS testing indicated that the soils would not liquefy in the classical sense, though cyclic softening behavior was observed. The CDSS results were used to develop a Cyclic Resistance Ratio curve for the diatomaceous soil to compare with clean sand liquefaction curves. Seismic lateral pile capacities were developed using two approaches. One approach used conventional p-multipliers for liquefied soil and modified them to reflect expected excess pore pressure ratios. The other approach applied residual strength and fifty percent strain values from post-cyclic monotonic shear testing. A lateral spread hazard zone was identified along the Lake shoreline and reduced, seismic lateral pile capacities were recommended. The objective of this paper is to report the seismic design considerations for this project in a unique geologic and seismic setting. INTRODUCTION The engineering properties of diatomaceous soils have rarely been studied and the cyclic behavior under seismic loading is generally unknown. Some of the critical geotechnical uncertainties of diatomaceous behavior include potential for large consolidation settlement, influence of irrecoverable strains due to diatom particle crushing, shear strength (peak and residual), and cyclic properties. This paper presents results of cyclic shear testing, seismic evaluations and seismic lateral pile design in diatomaceous soils performed for the expansion of a waste water treatment plant in the city of Klamath Falls, Oregon, site of the largest recorded earthquake in Oregon’s history. The expansion consisted of adding six new facilities at the existing Plant including influent pump station (IPS) and headworks, aeration basin, tertiary treatment, and other buildings. The IPS/headworks and aeration basin will be founded approximately 15 feet below ground. The other buildings will be founded at grade. The existing facilities are supported by timber piles that penetrate the surficial diatomaceous soils and terminate on a hard underlying deposit. Figure 1 shows the site plan and proposed additions.

Jan 1, 2018

Balancing the prodigious iron ore deposits of Western Australia are the equally vast coal resources of the Bowen series of eastern Queensland. The Bowen series is a Permian basin stretching 500 miles in a north-south line. The beginning of what will be large scale mining of the Kianga-Moura coalfields in Dawson Valley was made by the Australian company of Thiess Bros. in July 1961. Then Peabody Coal Co. of St. Louis, Mo., joined Thiess. Later, Mitsui & Co. Ltd. received a 20% interest in the firm Thiess, Peabody, Mitsui Coal Pty. Ltd. Rtitsui was to lend the company money for development. Queensland Parliament, by special act, granted the company exclusive franchise over the Kianga-Moura coalfield, an area of 350 square miles. The rights do not include other minerals. The company is to have a 120-mile railroad completed to Gladstone or some other port in seven years. It must produce at least 500,000 long tons of coal annually until the line is built, after which production is to be upped to 2 million tons. By December 1962, these arrangements were completed.

Jan 10, 1964

By Elizaveta Cheremisina

In steelmaking process lime serves as flux. Rapid lime assimilation and slag formation of the desired composition have a significant effect on the refining reactions. It is important to know the rate limiting step of lime dissolution to control and improve the converter process. Kinetics of pure CaO and industrial lime dissolution in model slag has been studied in the range of temperatures 1300 –1600°C. Lime samples were prepared in cylinder form and immersed in the melt for predetermined time. Considering the total mass balance of CaO in the slag and linear dimensions of lime samples, mass transfer coefficients were derived. Diffusion coefficients were calculated under conditions of non-stationary diffusion. The derived activation energy of less than 200 kJ/mol indicates that diffusion is the limiting step in the process of lime-dissolution in slag.

Oct 30, 2017

By Charles Zimmerman

The Genesis gold mine, owned and operated by Newmont Gold Co., is located in section 31, T36N, R50E within Eureka County, Nevada along the Carlin Trend of sediment-hosted disseminated gold deposits. Mining commenced in 1986 with present mineable and stockpiled reserves listed at 17,711,000 tons of ore averaging 0.073 opt Au, totalling 1.292 million ounces of gold. Ore is primarily hosted within Devonian calcareous siltstones that have been subjected to intensive argillization and silicification episodes. Additional mineralogic and geochemical features of the Genesis ores include enrichment in iron-oxides, kaolinite, arsenic and antimony; the ore zone is relatively depleted in carbonates and sulfides as a result of supergene and hypogene oxidation. Two major structural zones enhanced the permeability of the siltstones and served as the main hydrothermal conduits within the deposit. Prior to the main ore stage, the host rocks were subjected to metasomatic effects caused by emplacement of the Juro-Cretaceous Goldstrike granodiorite pluton and associated dikes and sills. Micron-size gold occurs in clays, micro-crystalline quartz, and in arsenical complexes. Non-oxidized carbonaceous and sulfidic ores and silica-locked ores result in variable preg-robbing and refractory responses during cyanide recovery. Selective mining and milling has resulted in the successful treatment of the Genesis orebody.

Jan 1, 1988

By D. W. Tuckwiller

Electroplating is a widely utilized but little understood process. The fact that the average person is in contact with dozens of plated items daily without even being aware that they are electroplated is evidence of the success of the process. Although a complete explanation of electrodeposition involves thermodynamics and modern theories of bonding and catalytic reactions, in its simplest form the process conforms to the following description. A metal salt dissolved in water partially dissociates into negatively charged and positively charged ions. In the case of nickel sulfate dissolved in water, for example, a portion of the salt dissociates into positively charged nickel ions and negatively charged sulfate ions. If an electrical potential is applied between two electrodes in this solution, the nickel ions migrate toward the cathode and the sulfate ions toward the anode. The negatively charged cathode has a high concentration of electrons, which combine with the positively charged metal ions to form neutral metal atoms with a stable electron configuration. These insoluble atoms thus form a deposit on the cathode.

Jan 1, 1970

By CHENCHEN SUN, GUOPING LUO, GUOCHENG ZHANG

Preparation of briquettes by adding CaF2 reagent into the Australian iron ore powder. The structure and morphology of iron ore briquettes during various reduction stages (i.e., Fe2O3→Fe3O4, Fe3O4→FeO, and FeO→Fe) were observed via an ore microscope and scanning electron microscopy. The results showed that CaF2 reacted with SiO2 to form CaO and SiF4 gas during the roasting process. The reduction swelling index decreased from 12.36 to 8.83% when the CaF2 content in the briquettes increased due to CaF2-mediated refinement of the hematite grains during the first stage of the reduction process. Lattice distortion resulting from the presence of Ca2+ in the FeO lattice during the second stage of the reduction process, coupled with an increase in the porosity of the iron ore briquettes and the formation of a low-melting-point slag phase, promoted the anisotropic growth of FeO lamellar crystals, which resulted in an increase in the reduction swelling index from 4.27 to 7.36%. During the third stage of the reduction process, the growth of iron whiskers was promoted by wüstite (FeO) lattice distortion caused by a solid solution of Ca2+ in the FeO lattice; the reduction swelling index increased from 15.61 to 24.72%, resulting in the catastrophic swelling of the iron ore briquettes.

May 27, 2021

By Joseph Hartshorne

The attention which this process has attracted, especially in Europe, has led me to believe that members of the Institute would be interested in a report of the progress which has been made in the year and a half that has elapsed since my paper on the subject was read at the Colorado Meeting of this Institute. As already described in that paper (Duns., xxvi., 380), this process is a modificatioii of the open-hearth steel manufacture, whether acid or basic, collsistillg essentially in the division of the charge between two furnaces, one of which is charged about two hours earlier than the other, and tapped into the other after the charge in the latter has become fluid, the slag of the first bath being removed from it during the transfer. This description still remains true as far as it goes, but further experience has demonstrated that circumstances will very materially modify the relation of the two furnaces to each other, and the character of the work done in each of them. The function of the primary furnace has become more clearly and entirely that of doing the rough work of desiliconiziug and dephosphorizing, while that of the second or finishing-furnace has become almost entirely that of decarburizing and finighing the heat. To indicate these developments and their results is the object of this paper. In order to avoid needless repetition, I shall try to accomplish part of this object by giving a short resume' of what has been published elsewhere on this subject since my former paper was read. This will at least enable those interested to study the matter for themselves from original sources. Since that time the following papers have been read and published: " The Bertrand-Thiel Process of Making Steel," by Percy C. Gilchrist (Cleveland Institution of Engineers, Session of 1896-

Jan 1, 1899

By V. Srajer

The loading and hauling equipment simulation model was developed to satisfy, the requirements and need of the mining industry in western Canada. It is expected the model will be used to determine the' impact of various combina¬tion of loading and hauling equipment, company policies and maintenance procedures, haulage requirement, to evaluate possibilities, of the use of truck monitoring and dispatch systems, and to access loading and hauling equipment productivities. To evaluate the model, and to access its capabilities in addressing the above requirements, the model was validated. The validation was based on the following: 1. Running the model in-house to evaluate its structure, 2. Running the "test case" by timing models developed elsewhere to compare the results of simulation, 3. Soliciting of model critique from outside agencies, and 4. Comparison of calculated data with real time study data. The presented paper provide overview of the validation processes and summarize" results obtained during comparison and evaluation studies.

Jan 1, 1989

By Morland R

In the course of an exploration program aimed at increasing Pasminco Mining's ore reserves, an electromagnetic survey down one of the underground drillholes at the North Mine, Broken Hill, recorded a broad and persistent response. This paper demonstrates that the anomaly was not due to any geological feature, but rather was caused by 'self-response' of the sensing probe. The observed results are due to the surveyed hole lying within a resistive environment and having distinct, but not unusual, changes in dip.This phenomenon has not been widely reported and we believe that there are likely to be similar cases in company records where very genuine looking responses are due to self-response rather than sulphides. These false anomalies can be recognised by correlating the observed data with the calculated down-hole component of the transmitting loop's primary field.

Jan 1, 1994

By S M Richardson, A W McNeill, J B. Gemmell

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Hellyer, Fossey, Que River and Mount Charter volcanic-hosted massive sulfide (VHMS) deposits occur within the Que-Hellyer volcanics of the Mount Read volcanics, Tasmania. These deposits occur along a 6 km strike length and are hosted by the same stratigraphic unit. We use a combination of whole-rock geochemistry, short wavelength infrared (SWIR) spectrometry, laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analyses and compiled historic whole-rock geochemical data to develop district-scale vectors towards VHMS mineralisation.Strongly sericite and K-feldspar altered rocks concentrate along a linear trend from Hellyer, through Que River, to Mount Charter. Ishikawa alteration index values and whole-rock major and trace element concentrations provide exploration vectors towards mineralisation on a regional scale as significant enrichment and depletion trends. On a deposit scale, composition variations in white mica (sericite alteration), chlorite and K-feldspar are observed and reflected in whole-rock geochemical variations. Regional SWIR data from drill core support the prevalence of phengitic mica and high-Mg chlorite within footwall alteration halos and highlight the main upflow zones of hydrothermal fluids in the VHMS district. The combined use of regional whole-rock geochemistry, SWIR and mineral chemistry is an effective way to highlight prospective areas for VHMS mineralisation in a mature exploration province.CITATION:Wu, S, Gemmell, J B, McNeill, A W and Richardson, S M, 2015. Exploration implications from variations in whole-rock and mineral chemistry around the volcanic-hosted massive sulfide deposits of the Que-Hellyer volcanics, Tasmania, Australia , in Proceedings PACRIM 2015 Congress, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By E. James Quinn

Solvent extraction technology using EHEHPA (2-ethylhexyl phosphonic acid, 2-ethyhexyl mono ester) is the norm for industrial separations of rare earth elements. This process has some shortcomings, including a large number of stages compared to most SX processes and high acid requirement for stripping of the heavy rare earths. In this work, we examine a number of alternative mixed solvent extraction systems: (i) Mixtures of organophosphonic and phosphinic acids such as EHEHPA/Cyanex 272 or Cyanex 572; (ii) Ionic liquid mixtures of EHEHPA with quaternary ammonium chloride (Aliquat 336); and (iii) Mixtures of carboxylic acids for yttrium/lanthanide separations. We discuss and compare the efficacy of these systems with reference to the Nd/Sm separation, which is of industrial significance. Based on the extraction chemistry and the use of modelling tools to define the counter-current solvent extraction circuit, we present a techno-economic analysis of a separation plant and discuss the impact of various solvent systems on the capital expenditure (CAPEX) and operating costs (OPEX).