Search Documents

By G. H. Lovell, W. J. Parton, J. J. Crane

IN 1949 Lehigh Navigation Coal began a study to improve its mining methods. At this time the company mines were using conventional breast and pillar and slant chute methods to mine the. steeply pitching coal (40º to 90º). Mining costs were high, the miners' productivity low. There were many hazards typical of the methods employed. Coal seams in the Panther Creek Valley area of the southern anthracite field form a syncline dipping 40" to the south and 75º to 80º to the north, the lowest point 1500 ft from surface. Several contiguous veins 7 to 50 ft thick are mined. Characteristic folding is shown in Fig. 1.

Jan 3, 1957

By D. Y. Li, C. D. Ma, T. Zhou, T. J. Cheng

In this paper, a number of experimental tests are carried out to study the strength difference on rectangular prismatic marble specimens with different height-to-width (H/W) rations. The specimens have a nominal size of 45×15 mm in the compressive cross-section (W×T) and different heights (H = 22.5 mm, 45 mm, 60 mm and 90 mm). It is to say that the height-to-width ratios are equal to 0.5, 1.0, 1.33 and 2.0, respectively. The quasi-static uniaxial compressive tests are finished by a servo-controlled INSTRON machine (the strain rate at about 10-5/s), and the dynamic compressive tests are finished by a diameter of 50 mm cylindrical SHPB apparatus (the strain rate reaching about 101/s). The rock failure process of marble specimens is captured by a high speed camera in order to distinguish the fracture propagation behaviour. It is found that the compressive strengths increase when the H/W ratio of marble specimen changes from 2.0 to 1.0 due to the end clamping effect both for quasi-static and dynamic loads. However, when the H/W ratio changes from 1.0 to 0.5, the apparent compressive strengths decrease both for the two loading conditions. The strength decrease of short marble specimens may be attributed to the change of failure mode from shear to slabbing, which can be identified by the fracture patterns of the specimens. Based on the uniaxial compressive tests, the slabbing strength of the marble was found to be about 40% of its UCS for the specimens with a nominal height-to-width ratio of 2.0. In addition, it is found that the dynamic increase factors (DIF) are affected by the specimen’s aspect ratios. It implies that the same aspect ratios should be used to compare the dynamic and static compressive strength of rocks. Meanwhile, both the static and dynamic tensile strengths of the marble are obtained by the Brazilian disc tests. The ratio of the dynamic tensile strength to the static tensile strength of the marble is about 2.68.

Jan 1, 2015

By Louis Donolo

New buildings in today's urban environment, especially in down-town areas, invariably involve the construction of multiple level basements. Used for parking, storage and commercial space, these underground structures normally extend 30 to 50' and more below grade and, to make optimum use of expensive land, they usually occupy the full site right up to street/sidewalk and property lines. SOIL SUPPORT SOLUTIONS Building these basements requires vertical excavation, and consequently, a temporary soil support system which will eventually be replaced by the permanent foundation walls of the structure.

Jan 1, 1987

By W. J. Kempson

As a result of the rising electrical energy costs in South Africa, a method was sought to reduce the overall electrical consumption of typical shaft systems. A typical shaft configuration was analysed and the primary energy consumers were identified. The ventilation fans for this system were found to consume 15% of the total energy of the shaft system. It was calculated that more than 50% of this energy is consumed by the shaft itself, more specifically, by the pressure losses that occur in the shaft as the ventilation air passes through it. In order to ensure that the theory being used for the evaluation of these shaft systems is accurate, a total of five shafts were instrumented and the actual pressure losses over the shafts plotted against time. These shafts were then analysed from a theoretical perspective. Finally, in order to ensure a thorough understanding of the behaviour of the ventilation air in shaft systems, the systems were simulated using computational fluid dynamics (CFD) techniques. There were significant discrepancies between the theoretical analysis and the CFD simulation during the initial comparisons. This discrepancy lessened as the complexity of the CFD models increased, until when the complete shaft was modelled using the full bunton sets, the pipes, and the flanges, the difference between the theoretical evaluation and the CFD simulation was small. This result demonstrates that the theory is insufficient and that the interrelated effect of the buntons and fittings has not been fully appreciated by current theory. The final phase of the work presented here was to evaluate the costeffectiveness of using different bunton shapes and shaft configurations. It is shown that the increase in the pressure losses and therefore the direct operating costs of the shaft can vary by as much as 80%, depending on the bunton configuration chosen. The placement of the piping in the shaft can increase the pressure losses, and therefore the direct operating costs of the shaft, by as much as 12%, depending on the placement of the piping in the shaft; this effect includes the use of flanges. The use of fairings on a large cage can reduce the resistance that the cage offers to the ventilation flow by as much as 30%. This, however, does not translate into a direct saving because as the cage moves through the shaft, the overall effect is transitory. These savings can be significant when the items highlighted in this work are applied correctly. Keywords shaft design, ventilation, energy consumption, modelling, CFD.

Dec 1, 2013

By Dennis Molvik, Roberto J. Guardia, Brad Cowles, Rick Andrews, Robert A. Robinson

A 220-meter (m) segment of the Henderson/ ML King Combined Sewer Overflow(CSO) consists of two 1.8-meter-inside diameter (I.D.) pipe-jacked tunnels that pass beneath Interstate-5 and the BNSF and UPRR railroads. A seismic tomography survey was conducted to develop a 3-dimensional profile of the tunnel zone and better define potential obstructions. The tomography was conducted through three 11 cm high-density polyethylene (HDPE) pipes installed in a triangular pattern around the future tunnel alignments using horizontal directional drilling methods. The pipe-jacked tunnels have been successfully completed, thus permitting a comparison between the predicted obstructions and those actually encountered. The top HDPE tomography pipe was also used to monitor settlements with an experimental horizontal profiler above the advancing tunnels during construction and located two areas of ground loss beneath I-5 that were subsequently grouted.

Jan 1, 2005

Proceedings of the Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry, Montreal, June 1970. The Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry was sponsored by The Canadian Institute of Mining and Metallurgy, McGill University and Ecole Poly technique. The programme included 71 papers on various topics, as follows: Market Analysis and Logistics Planning; Quantification of Geological Variables; Blending; Capital Investment Decisions; Mining; Financial and Economic Analysis; Search for Mineral Deposits; Market Forecasting and Strategies; Operations Research in Process Modelling; Ore Reserve Estimation; Management Information Systems; Optimization and Control of Mineral Processes. In addition to general sessions, a special feature of the Symposium was Executives' Day, which was held to provide top and middle management with a broad understanding of the usefulness of decision-making techniques and their role in the mining organization. Panel Discussions and two keynote speakers provided a review, in non-technical terms, of the areas in which decision-making techniques have proven valuable. The present volume contains 65 papers submitted for publication, along with a complete account of the Executives' Day discussion. It is broadly divided according to the above subject headings. Approximately 550 pages, illustrated. Price: $15.00; $12.00 to students, plus 50 cents for handling costs. Order now from CIM headquarters: Canadian Institute of Mining and Metallurgy, 906-1117 Ste. Catherine St. W. Montreal 110, Quebec.

By F. E. P. PEARSON

Sandstone quarried from an island in Lake Winnipeg is barged 130 km to a processing plant at Selkirk on the Red River. The stone is white, poorly consolidated, and consists of rounded quartz grains of high natural purity. It is an important supplier of silica in Western Canada for glass, fiberglass, foundry and other industrial uses.

Jan 1, 1984

By M. K. LeBegue

Water sprays located behind the bits of cutter drums have been shown to reduce the incidence of face ignitions. This paper details the design approach to successfully incorporating water seals into a drum miner cutter head.

Jan 1, 1999

By Cristina Cereceda

El presente texto describe los flujos volcánicos en el valle de Chili, Arequipa con el objetivo de establecer la estratigrafía y reconocer las características sedimentológicas de los flujos de escombros volcánicos en la cuenca media del río Chili, así como realizar una evaluación y zonificación de peligros por emplazamiento de flujos hiperconcentrados a partir de una simulación con el programa FLO2D. La zona de estudio comprende el valle del río Chili, desde el santuario de Chapi Chico hasta Uchumayo, donde los trabajos geológicos realizados a nivel de detalle evidencian 10 depósitos de lahar y 12 depósitos de flujos hiperconcentrados provenientes del Misti, Pichu-Pichu y Chachani, emplazados en el Holoceno y época histórica. Así tambiénel mapa de peligros generado, muestra que las zonas de mayor peligro corresponden al sector Yanahuara-Pampas del Cuzco. En caso de una erupción del Misti, la posibilidad de formación de estos flujos es alta, destruyendo la infraestructura cercana al cauce del río Chili y desabasteciendo de agua para la población e industria, especialmente minera.

Sep 14, 2009

By Markus Pötsch, Andreas Gaich

Optimization of surface blasting based on 3D models from drone imagery and a closed loop that starts with an automatic analysis of the geometry and the geological conditions and ends with an objective assessment of the blast result.

Feb 1, 2020

By U. Martin

Advanced copper materials for conducting applications require an optimal combination of high mechanical strength at ambient and moderately elevated temperatures together with superior electrical and thermal conductivity. Mechanical alloying under repeated cooling of the milling vials in liquid nitrogen has been applied to produce ultra-fine grained (UFG) oxide dispersion strengthened (ODS) copper with a high yield strength at ambient temperature. In the present study ODS copper was manufactured by mechanical alloying of copper powder and 3% by volume of incoherent oxide dispersoids. During the high-energy milling a homogeneous distribution of fine dispersoid particles (diameter nearly 100 nm) can be achieved in the powder. Samples with a density of more then 97% of theoretical value were produced by uniaxial hot pressing under 650 MPa at 600°C for 20 minutes. The high yield strength at ambient temperature can be described by a linear superposition of the Orowan stress for particle hardening and of ultra-fine grain strengthening according to the Hall-Petch mechanism. Simultaneously, a best value of 75% IACS could be obtained for the electrical conductivity. The creep behaviour of ODS copper in the temperature range from 500°C to 700°C is described within the frame of diffusional creep deformation.

Jan 1, 2007

By J. D. Grozier, W. W. Mullins, H. W. Paxton

The morphology of the nucleation and growth of austenite into high-purity iron in NH3-H2, gas mixtzires has been studied. The growth rate of an austenitic rim (planar interface) from scratched surfaces of- polycrystalline iron specimens was determined as a function of temperature and percent NH3 and found to he in reasonahle agreement with growth-rate calculations based on a model which assumes the diffusion of nitrogen to he the rate-controlling step. Under certain conditions, austenite pew as platelets; growth rates of these along the surface of single crystals were found to he dependent on surface preparation, orientation, THE development of microstructures can conveniently be thought of in terms of nucleation and growth. The complex topic of nucleation in solid-solid transformations will not be discussed at length, although a few qualitative experiments were performed. Growth is determined by the mobility of the various possible interfaces under the available driving forces in a particular situation. In homophase transformations, it has been clearly demonstrated that the mobility is very sensitive to small amounts of impurities, to the kind of impurity, and to the orientation relations across the boundary.' A degree of quantitative knowledge has temperature and percent NH3. On electropolished surfaces with a (110) pole, the maximum growth rate of platelets was determined and found to be in agreement within a factor of 2 to 3 with theoretical calculations of the edgewise growth rate of a platelet. The calculations are based on a model which assumes that the diffusion of nitrogen in the ferrite in front of the moving curved attstenitic interface at the tip of the platelet is the rate-controlling step. The growth direction on the surface of the single crystal and resztlting habit plane of the platelets were determined and found not to he unique but to vary systematically with the pole of the surface. been obtained. In the case of heterophase transformations, which are significantly more complicated to treat, a comparison of theoretical and experimental studies often shows rather poor agreement.'-' The main purpose of the experiments discussed below was to obtain additional quantitative data on crystallographic effects on boundary mobility in a system which was otherwise as simple as possible, viz. the growth of iron-nitrogen austenite into fer-rite. In the course of the experiments, it became necessary to re-examine the theory for the growth of Widmanstatten plates, especially the influence of anisotropic interfacial free energy. Some other minor experiments in the Fe-N system were performed, and are described briefly. EXPERIMENTAL METHODS A) Material Preparation. The floating zone purified iron used for this investigation was supplied by Battelle Memorial Institute. The nominal composi-

Jan 1, 1965

By Bruce A. Kennedy

The first light of dawn was appearing through the window of the giant Pan American Boeing 747 as we crossed the Irish Coast on course into London's Heathrow Airport While still over Ireland, the plane began its descent and a few minutes later an announcement on the public address system informed us that we were coming up on Lands End. Cornwall, and would then begin our final approach into London. Barely visible below through the WISP). clouds were the Seven Sisters Lighthouse and the rugged cliffs of Lands End and Cape Cornwall, the westcrnmost point of England. Start at Lands End To a displaced Englishman, it seems amazing that technology has brought us to a point where large jet aircraft use Lands End as the starting marker for final approaches into London. It was not so very long ago that we considered the eight-hour car journey or the 12- hour train trip from London to Lands End as a major undertaking. Today, with the 180,000-lb thrust of four engines, this enormous aircraft transports 350 or more passengers that distance in a matter of a quarter of an hour. The incongruity of the situation is that the technology leading up to the development of the powerful jet engines used on: today's aircraft started with the ; invention of the steam engine which found its first commercial use some 300 years earlier in the mines of Cornwall 20,000 ft below.

Jan 1, 1971

By Ben F. Dickerson

For a number of years in office bull sessions, I have not so jokingly discussed the engineering or management fiasco of the year or decade. Usually, governmental projects are in the vanguard, such as tanks that won't tank, or heavy water plants that don't produce heavy water, etc., etc., all to the flutter of the taxpayers' hundreds of millions, or billions of dollars. The mining industry has also brought forth a share of this type of fiasco. Ordinarily, due to lack of funds, not opportunity, the stockholders only stand losses of a few tens of millions. Little knowledge of these major errors gets to the outside world, for the ordinary stockholder is usually not very alert, and managements are extraordinarily adept at discreet midnight internments in the fine print of the footnotes of annual reports.

Jan 1, 1975

By C. M. Acuña

At the Chuquicamata Division of Codelco-Chile high arsenic concentrates are produced, which at the smelter are processed via the Outokumpu Flash Furnace and Teniente Converters to obtain copper mattes. In the case of the Teniente Converters the production of matte grade near white metal composition is a common practice since the eighties and provided in the pyrometallurgical route no appropiate measures are taken, penalties have to be paid because of arsenic content in the anodes. During smelting huge volume of slag is produced and elimination of arsenic by slagging at this step is not economically attractive. Although during fire refining is possible to eliminate arsenic by use of mixtures of calcium and sodium carbonates this alternative is expensive, takes long process time and decreases the lifetime of the refractory lining. In spite of these facts a reasonably way to control arsenic in metal, and therefore in the anode, is taking, action in the converting step. The effects of oxygen and arsenic content in metal, arsenic in white metal and basicity index of the slag upon the distribution coefficient of arsenic between metal and slag were investigated at pilot and industrial levels. The best results are obtained for metals around 7,000 ppm oxygen and 0.3 basicity index slag, which results in a 5.7 distribution coefficient for a 5,800 - 7,100 ppm arsenic content in white metal, 18%-24% CaO slag at 1473 - 1523K. Furthermore, no significant/visible refractory wear has been realized.

Jan 1, 1999

By M. M. Cole

An assessment of the combined application of remotely sensed satellite imagery, geobotany and biogeochemistry reveals the complementary value of these techniques in the Thalanga area. The SPOT imagery yields useful information on features of the terrain and discriminates the gossan over the ore zone. Geobotany differentiates geological units and the anomalous vegetation provides visual expression of the surface presence of the ore zone, while biogeochemistry effectively locates its concealed extension below Tertiary sediments and ferricrete

Jan 1, 1991

By Shemek Oginski

The 5 km (16,194 lf) of 6.1m (20 ft) diameter TBM driven tunnel built by the J.F.Shea Co. will serve as sewage overflow storage. The TBM tunnel and four connecting tunnels excavated by drill and blast methods in hard granite will remain unlined. Based on the Geotechnical Baseline Report (GBR), the Contract documents provided a design with no required pattern of rock bolts, no probing, no pre-excavation or consolidation grouting, and lastly, no final lining of the tunnels was deemed necessary. This paper will provide a general overview of these topics with the emphasis on the actual ground conditions encountered versus the projected conditions provided in the GBR and how the GBR reflected the design of the project. Proposed modifications to the temporary and permanent ground support will be presented and the necessity of probing and pre-excavation grouting will be evaluated.

Jan 1, 2005

By Baozhong Ma, Yonggang Wei, Shiwei Zhou, Bo Li, Chengyan Wang, Hua Wang

The effects of additives with Na2S, Na2SO4 and CaSO4 on phase transformation of nickel laterite ore in low-temperature reduction roasting process using carbon monoxide were investigated. The results showed that diffraction peaks of forsterite increased with increasing reduction temperature for 30min with the addition of 10wt% Na2SO4 and 50vol% CO, and diffraction peaks of forsterite increased with increasing the content of Na2SO4 at 900°C for 30min. Comparing the above three additives, phase transformation of nickel laterite ore were strongly influenced with the addition of 10 wt% Na2SO4 and 10 wt% Na2S. Calcium sulphide from the thermal decomposition of CaSO4 was carried out in the reaction product. SEM-EDS analysis result deduced that increasing the dosage of Na2SO4 from 10wt% to 15wt% could promote the polymerization of ferronickel and improve the grade of nickel in ferronickel.

Jan 1, 2015

By M. R. TECK, N. Rudd, L. K. Thomas, D. L. Katz

The authors are to be congratulated for presenting the first comprehensive paper on the theory and practice of threshold pressure determination in connection with underground gas storage. It is of particular value since most previous experimental work on this subject has been proprietary to the commercial laboratories engaged in such testing and to their clients. This dlscussion is presented in amplification of the subject paper, not in criticism, and is based upon our experience with approximately 5,000 threshold pressure determinations. Our comments are directed primarily to the experimental procedures as described by Thomas et al. It should be noted that, while clay mineral-rich lithologies are the most common caprock materials, the samples used (Table 1) include low permeability sandstones and carbonates, but do not include shales or other formations in which clav minerals exert a dominant effect. While our experience on samples analogous to those investigated by the authors generally confirms their findings, we have found that even more rigorous experimental conditions must be imposed where clay minerals are the controlling factor. These additional conditions result from the well-known molecular character of the clay minerals themselves in which water is interlaminated with, and bonded to, silicate sheets, thus becoming an essential component of the molecule. In many clay minerals the character of the intersheet bonding, and thus the dimension of the lattice, is strongly affected by variations in the identity and concentration of cations present in the intersilicate water. On a supermolecular scale, adsorbed water films on particle or "flakes" of shale provide much of the cohesive force necessary to maintain mechanical strength. The thickness of these films is variable and inversely proportional to intergranular pressure within the dimensional limits involved in caprock investigation. The thickness of the intersilicate water layers may also be subject to pressure under some conditions. These considerations are reflected in several necessary modifications of the experimental procedures described by the authors. Two of these are, in our judgment and experience, of such importance that they cast real doubt on the validity of data obtained on argillaceous materials without their application. The very careful resaturation procedures proposed by the authors should give good results in connection with the relatively "inert" lithologies used in their experiments. Our experience suggests, however, that they would create more problems than they would eliminate if applied to argillaceous materials. 1. Drying of the sample at the temperature and for the duration indicated by the authors not only will dessicate the sample with consequent shrinkage cracking, parting along bedding planes, and even total disassociation in the case of fissile shales, but it may also alter the character of the clay minerals themselves — in some cases irreversibly. 2. Prolonged evacuation to 2 microns Hg further dessicates the sample and is even more effective in reducing the intersilicate water content. 3. Resaturation with water differing in pH or chemical content from that existing originally in the sample also serves to alter the nature of the sample, particularly its structure and strength. 4. Our experience has been that, even with the thorough precautions proposed by the authors, complete resaturation of very fine grained materials is rarely obtained. Yet our experience confirms the

Jan 1, 1969

By Collin Stewart

Bowie Resources maintains one of the most pro-active ground control programs in the U.S. mining industry today. Its guiding philosophy is that everyone in the organization, from the miners at the face all the way through the top management, are involved in ground control. Some of the unique elements of the Bowie ground control program include: ? Roof bolt operators log the stratigraphy of test holes in nearly every cut. These ?lithgraphs? are used by section foremen to determine the need for additional roof support, and they are entered into the geologic data base for use in geologic modeling and mapping. ? Underground core drilling is conducted to obtain data for CMRR and stability maps. ? Weekly ?Quality? meetings, involving mine management and technical staff, are held to ensure that ground control information is integrated into production operations. The paper will describe the program in detail, discussing the involvement of roof bolters, section foremen, surveyors, technical staff, and production managers. It will also show how the program has contributed to the mine planning process. Case histories of successful ground control interventions will be discussed.

Jan 1, 2006