Search Documents

By Robert D. Schmidt

The Bureau of Mines is conducting an investigation to develop remediation techniques for residential water wells whose yield has been affected in the long term, by underground mining. Initial work relating to this project was conducted in 1984-1987 at a room and pillar mine in Indiana County, Pennsylvania. Piezometer nest data from the room and pillar mine reveals that a downward gradient in piezometric head exists in shallow strata as a result of drainage into the underlying mine void. The vertical gradient in head in turn results in well bore leakage in open-hole water wells. The relative yield of valley wells is only slightly affected however because the high surficial recharge rate through fractures more than compensates for fracture leakage into the underlying mine. The relative affect of well bore leakage on well yield is greater in certain hillside and hilltop wells that have comparatively low inflow rates at shallow depths. The static water level of such wells is determined to a much greater extent by the chance interception of deep outflow fractures, than is the case for wells drilled in a more intensively fractured valley bottom. The lower static water level of wells that intercept deep fractures does not necessarily reflect the water table conditions outside of a small radius around the affected well. The results suggest that permanently isolating well bore outflow fractures may remediate certain open-hole residential wells that have been affected by high extraction underground mining.

Jan 1, 1986

By Keith A. Heasley

Exactly 25 years ago this month (August 12, 1981), IBM introduced the ?Personnel Computer? with a 16 bit operating system called MS-DOS 1.0. Since then, Moore?s Law, which essentially states that computer capability will doubled every 18 months, has been fully evident in the computer industry. As computers have advanced from main frames to initial personnel computers to the powerful graphical workstations of today, numerical modeling for ground control in mining has followed closely behind. Twenty five years ago, many numerical methods for solving ground control problems were little more than equations on a piece of paper. In the intervening years, these numerical models have grown from initial trial programs to highly-complex computational systems with numerous capabilities for different material behavior, failure criteria, gridding methods, discontinuities, etc. In some instances, the capability of the programs has quickly outstripped the geo-technical modeler?s ability to get accurate, realistic input and boundary conditions. This paper will look at: how numerical models have evolved in the last 25 years, how the models have been applied to ground control problems in that time period, and where numerical modeling is headed in the immediate future.

Jan 1, 2006

By C. Mosoane

ERPM was formed in 1893 and as a result of its age, a large volume of data exists in a paper-based format and it was decided to electronically capture data in one of two critical mining areas?namely at Far East Vertical (FEV) Shaft Area (Lower Areas) and Hercules Shaft Area (Upper Areas). The life of mine is dependent on tonnage and grade from these areas. Geostatistical evaluation of the gold reserves has been applied on an ad hoc basis in the Hercules Shaft Area and on a continuous basis in the FEV area. This is the first evaluation using geostatistics that was performed on the Upper Areas. This paper is based on the premise that regardless of cut-off grades, geostatistical estimation (kriging) estimates and locates reserves better than ?traditional? methods e.g. polygonal method, inverse squared distance method and it endeavours to estimate and locate the high grade reserves in the Main Reef Leader of Upper Areas.

Jan 1, 2003

By C. N. Schuette

"The production of silica and magnesia crucibles in the induction furnace was attempted and achieved in the laboratory of the Pacific Experiment Station of the United States Bureau of Mines. This work was undertaken at the request of other stations for laboratory crucibles of a certain specified wall thickness and capacity.The essential new parts of this work are the development of a technique for the high-frequency furnace production of silica crucibles of greater wall thickness than could be readily fabricated from commercial fused silica, and for heavy-walled magnesia. crucibles of great density and mechanical strength. A considerable bode of patent literature on the Production of fused silica ware in resistor-type furnaces was examined, but it furnished no significant help for the present problem. Similarly sintered magnesia refractories are often made for technical purposes, but for use at temperatures of 2000o C. or over, the material must be sintered at higher temperatures than can be attained by combustion firing, and the very great shrinkage encountered at these temperatures requires special methods. Small crucibles. of magnesia fused in the electric arc have been made by Tritton and Hansen,3 but the practical size of such containers is very limited.Many different methods of making crucibles in the induction furnace were tried before satisfactory results were obtained. The following description covers only the most satisfactory method, which produced crucibles of excellent quality in a reasonable time and with a moderate expenditure of power and materials."

Oct 1, 1929

By A. Fahr, T. Byczkowski, M. Genest, C. Mandache

"Layered aluminum structures assembled with rivets are often found in aircraft fuselage. These structures are exposed to various mechanical loads and a range of environmental conditions that contribute to their ""aging"". The rivet holes are the source of stress concentrations and the location of crack nucleation and growth. Detection and sizing of second and third layer cracks under fasteners represent a major challenge for non-destructive evaluation (NDE) technicians. Electromagnetic methods are currently the most feasible NDE techniques that are capable of successfully inspecting such structures. However, different probe lift-offs, due to protruding rivets and paint coatings, or interlayer separations, due to sealant or air gaps, pose difficulties in detecting and sizing cracks. In addition, the use of conventional eddy current technique is limited due to the inverse relationship between the probe spatial resolution and its field penetrability. In this paper, we present an alternative approach that overcomes the previously mentioned shortcomings by using pulsed eddy current excitation and magnetoresistive sensor pick-up. Various signal manipulations are employed for defect detection and quantification."

Jan 1, 2006

By S. Fugleberg

As a result of research work done during the planning of the Kokkola zinc plant it was found that a very efficient cementation of impurities from the suspension obtained after leaching copper and cadmium cakes was achieved by adding zinc dust to the batch without filtration after the leaching. All elements nobler than cadmium are precipitated with the exception of lead, which must be removed in a separate step. Using pure zinc dust, free from noble metals, the cadmium sponge produced will only contain elements that can be re- moved from cadmium by meltrefining. The process is thus : 1. Leaching and purification 2. Removal of lead (with BaCO3) 3. Precipitation of cadmium sponge with pure zinc dust 4. Meltrefining of briquetted sponge with NaOH for removal of Zn (and others) The paper deals with the removal of the most critical elements, i.e. Co, Ni, As, Sb, Cu, Pb, T1 in the liquid phase and Zn and T1 in the melt. A survey is also given of the behaviour of most of the other elements normally found in Cd raw material, such as Ge, Te, Se, Sn, In, Ga. It is shown that in most cases the benefit of an electrolysis in Cd production is very limited. In Kokkola 99.998% Cd is achieved by this method, but in favourable cases it may be possible to come quite close to five nines.

Jan 1, 1973

By Harold R. Kokal, Madhu G. Ranade

A metallurgical/flux is a substance that is added to combine with gangue (unwanted minerals) during ore smelting, with impurities in a molten metal, or with other additives in metal refining processes to form a slag that can be separated from the metal. Because slags are immiscible with the metallic melt and are of lower density, a separation of the slag and metal occurs if the viscosity and surface tension are of the proper values. The chemistries of slags are adjusted to provide the proper melting point, viscosity, surface tension, conductivity, specific heat, density, or chemical properties to effect the desired task. In addition to absorbing impurities from the metal, the purposes of the slag are to thermally insulate the metal bath, protect the molten metal from the atmosphere, and control the chemical potential of the system. Several excellent references on slags and metallurgical fluxes are available (Boynton, 1980, Lankford, Jr., et al., 1985, Turkdogan, 1983, Rosenqvist, 1974, Fine and Gaskell, 1984). The function of the slag might vary at different stages within a process prior to final melting. For example, the slag composition and behavior will change as materials descend in the iron blast furnace, or as they melt in the early stages of formation of steel- making slags. Selection of the chemistry for a slag might be influenced by factors outside the primary function as when blast furnace slags are used to make cement, rock wool insulation, or fertilizer supplements. Sometimes slags contain a sufficient amount of valuable recoverable elements to be sold as raw materials for other processes. Fluxes are often referred to as acid, basic, or neutral. Acid fluxes are those that generally form acids in water and bases are those that would generally form bases in water. Typical acid fluxes are silica, alumina, and phosphorus, although alumina can function as either an acid or base. Typical basic fluxes are lime and magnesia. Fluorspar, or calcium fluoride, is a neutral substance because it can be viewed as the reaction product of a base and an acid. The degree of acidity (ratio of acids to bases) or basicity (ratio of bases to acids) is often specified to characterize the slag chemistry for a particular system. The system might also be referred to as acid or basic depending on the choice of slag, for example, basic steelmaking uses slags with more bases (lime and magnesia) than acids (silica and alumina). Many forms of minerals and compounds have been used as fluxes depending on the process requirements, availability, costs, requirements for recycling of intermediate products, and environmental concerns. Because slags are most often mixtures of oxides and silicates, fluxes are usually oxides, carbonates (which decompose to oxides) and silicates. Slags comprising phosphates, borates, sulfides, carbides, or halides have also been used (Rosenqvist, 1974, Moore, 1981, Szekely et al., 1989). In ironmaking and steelmaking, some acidic components are sometimes added. In nonferrous processes slags and fluxes are acidic with silica as the primary component, and although the use of basic flux such as limestone or lime is not extensive, some amount is used to modify slag properties and some refining slags are lime based. The production of iron is accomplished by smelting of ores, pellets, and sinter in blast furnaces with subsequent refining of molten iron and scrap in oxygen-blown processes. The electric furnace is used to make steel, stainless steels, ferroalloys, and special alloys, whereas ferromanganese is often made in blast furnaces. Fluxes are used in all of these processes, and either limestone or lime is the major flux component with some dolomite, dolomitic lime, silica, alumina, and fluorspar being used. In ironmaking, the flux is added either by direct charging or through sinter and fluxed pellets. In steel refining by the basic oxygen process, flux is added as lime and dolomitic lime that are either charged as lumps or injected as fines. Some small amount of limestone is sometimes used. Fluorspar is often added as lumps or mixed with other fine materials in briquettes. Alumina is sometimes added to blast furnaces either by direct charging of sized lumps or through sinter. Typical acid fluxes are sand, gravel, quartz rock, used silica brick, or raw siliceous ore (Lankford, Jr., et al., 1985). Olivine, which is a magnesium-silicate mineral, has been added to iron blast furnaces to enhance removal of alkalis (Lankford, Jr., et al., 1985). Alumina in the form of bauxite, aluminiferous clay, and recycled alumina brick has been used as flux. Alumina can function amphoterically as either an acid or base, for example it can form aluminum silicate in high silica slags or calcium aluminate in lime-bearing slags (Lankford, Jr., et al., 1985). Limestone (calcium carbonate) and dolomite (magnesium-calcium carbonate), or fluxstones as they are sometimes called (Boynton, 1980), and their calcined forms, lime and dolomitic lime are the major basic fluxes. In the latter cases, the carbonates are de- composed in a kiln-type process to drive off carbon dioxide that might otherwise interfere with the subsequent smelting or refining process or require expensive forms of energy to effect the decomposition (e.g., by combustion of coke in the iron blast furnace). Limestone is considerably less expensive than lime because it is not calcined; however, lime is far more difficult to handle and reacts readily with water. Dolomite and dolomitic lime are used for their magnesia content. Fluorspar is a neutral flux often used as an additive in steel- making slags to improve fluidity, but it has also been used in combination with lime as a primary slag in electroslag refining (Duckworth and Hoyle, 1969). Fluorspar is available in several grades, with the lowest grade often used for steelmaking. When the price of fluorspar has risen, substitutes including aluminum smelting dross, borax, manganese ore, titania, iron oxides, silica sand, and

Jan 1, 1994

By G. C. Stone

AS the term "hardness" is used with many different meanings, it should be understood that it here means resistance to deformation by compression. It was determined by measuring the pressure, in pounds per square inch, necessary to reduce by 20 per cent., the length of cylinders 1 in. (25 mm.) in diameter by 2.6 in. (66 mm.) long. The tests were made at Columbia University on an Olsen 400,000-lb. machine, the load being applied at a constant rate of speed 0.0319 in. per min. The results were obtained by Messrs. Rigg and Williams, and some of them were given in a paper read at the Sixteenth Annual Meeting of the American Society for Testing Materials, in June, 1913. The remainder of the results were obtained in subsequent experiments by the same authors. In all cases, the results given are the averages of three or more closely concordant tests. All of the spelters tested were of standard commercial grades and all were of compositions making them good deliveries. The accompanying table gives the results arranged in the order of increasing hardness:

Jan 1, 1919

By George Bain

SOME problems concomitant with commercial exploitation of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service depart-ment wants defects rectified and the cause determined to avoid recurrence. The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character.

Jan 1, 1940

By Richard P. Hight

Abrasives include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean, or otherwise remove solid material, usually by rubbing action but also by impact (pressure blasting for example). They do not include abrasive tools, for instance, lathe tools and files-or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted although some chemical-action polishes and cleaners may also contain solid abrasives, for example, many automobile and metal polishes. General Considerations The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded abrasive products such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cutting edges when grains become worn-for example: in garnet for sandpaper neither highly cleavable or friable grains nor extremely tough grains are wanted. For still other uses, great hardness is objectionable; for example, abrasives for dentifrices and for glass-cleaning soaps. For the most efficient use in the more critical applications, the different types of abrasives are rarely completely interchangeable; thus, while crushed quartz and garnet are both used in sandpaper, the papers are not at all interchangeable in their use applications. In the last analysis, the choice of a high grade abrasive depends upon the quality and quantity of work done by the abrasive per unit of cost. Initial cost of an artificial abrasive may be much greater than that of a natural abrasive but the artificial abrasive may do so much better work than the natural one, and do it so much faster that the ultimate cost will be less. It is for this reason that artificial abrasives have largely replaced natural abrasives. Abrasive Value Mineralogical hardness or "scratch" hardness as expressed in Mohs' scale is an important property in evaluating abrasive materials, but, as noted before, it is only one of several essential properties. The mineral hardness of pure crystal almandite garnet is about 7.5, but if the crystal is crossed by incipient fracture planes, or if it contains inclusions of other minerals, the apparent or useful hardness may be much lower. While the quartz grains in a sandstone have a hardness of 7, the bond holding the grains together may be so weak that the stone is valueless as a commercial abrasive. In artificially bonded wheels and stones, the hardness, strength, and character of the bond are fully as important as the hardness of the abrasive grains. Thus, in an overall consideration of abrasive hardness of loose abrasive grains, both "scratch" hardness and toughness must be considered. In naturally or artificially bonded abrasive stones, bond characteristics are a third factor, which is most important. The problem of abrasive hardness is further complicated by the inadequacies of methods of testing hardness and of expressing relative values. The Mohs' scale is inadequate both because the methods of testing are very crude and

Jan 1, 1983

By Richard P. Hight

Abrasives include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean, or otherwise remove solid material, usually by rubbing action but also by impact (pressure blasting for example). They do not include abrasive tools, for instance, lathe tools and files--or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted al- though some chemical-action polishes and cleaners may also contain solid abrasives, for example, many automobile and metal polishes. General Considerations The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded abrasive products such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cut- ting edges when grains become worn-for example: in garnet for sandpaper neither highly cleavable or friable grains nor extremely tough grains are wanted. For still other uses, great hardness is objectionable; for example, abrasives for dentifrices and for glass-cleaning soaps. For the most efficient use in the more critical applications, the different types of abrasives are rarely completely interchangeable; thus, while crushed quartz and garnet are both used in sandpaper, the papers are not at all interchangeable in their use applications. In the last analysis, the choice of a high grade abrasive depends upon the quality and quantity of work done by the abrasive per unit of cost. Initial cost of an artificial abrasive may be much greater than that of a natural abrasive but the artificial abrasive may do so much better work than the natural one, and do it so much faster that the ultimate cost will be less. It is for this reason that artificial abrasives have largely replaced natural abrasives. Abrasive Value Mineralogical hardness or "scratch" hardness as expressed in Mohs' scale is an important property in evaluating abrasive materials, but, as noted before, it is only one of several essential properties. The mineral hardness of pure crystal almandite garnet is about 7.5, but if the crystal is crossed by incipient fracture planes, or if it contains inclusions of other minerals, the apparent or useful hardness may be much lower. While the quartz grains in a sandstone have a hardness of 7, the bond holding the grains together may be so weak that the stone is valueless as a commercial abrasive. In artificially bonded wheels and stones, the hardness, strength, and character of the bond are fully as important as the hardness of the abrasive grains. Thus, in an overall consideration of abrasive hardness of loose abrasive grains, both "scratch" hardness and toughness must be considered. In naturally or artificially bonded abrasive stones, bond characteristics are a third factor, which is most important. The problem of abrasive hardness is further complicated by the inadequacies of methods of testing hardness and of expressing relative values. The Mohs' scale is inadequate both because the methods of testing are very crude and

Jan 1, 1975

By E. A. Wieselmann

This chapter presents a successful approach for achieving mine entry stability at the Cane Creek potash mine by the utilization of closure measurements. The mine is located in southeastern Utah (Fig. l). Mining is being conducted at depths in excess of 3000 ft under structurally complex geologic conditions typical of the Paradox salt basin. The closure measurement systems described have definite application for determining relative entry stability in other nonelastic rocks which are similar in behavior to potash. Similar types of closure measurements have been taken in various underground openings throughout the United States, Canada, arid Europe. Application of this closure data has previously met with varying degrees of success as a tool for design of under- ground openings in both elastic and nonelastic media.1-32 Closure measurements can be made easily and economically and they provide a practical solutiori to a practical problem. They are in-situ measurements which do not necessarily require laboratory correlation. Simple closure measurements have special significance in potash because "steady-state" ' closure rate, or creep, of the entries is measured. These closure rates can be utilized because nonelastic media such as potash will never achieve absolute stability around a mine entry. The potash will tend to creep or deform until all entries are closed and the overburden stress is redistributed over what was previously the mine area. The time for this ultimate effect to occur is dependent on a number of mining and geologic variables. Percentage of mine extraction, mining

Jan 1, 1972

By Nur Hossain

Analysis of Linear Elastic Fracture Mechanics (LEFM) parameters via the Virtual Crack Closure Technique (VCCT) has been obtained for SENT specimens of AM6OB magnesium alloy. It is found that the ratio of initial crack length to initial monotonic plastic zone size is one of the critical factors in establishing the limit of using LEFM concepts. If this ratio is below a certain limit (i.e. when crack lengths are small in comparison to the plastic zone size), loss of similitude stress intensity factor range would occur. This ratio, therefore describes the limit below which the use of LEFM would no longer be admissible. In this study, the above limit was established for AM6OB magnesium alloy. In addition, fatigue crack propagation tests were conducted to ascertain the fatigue response of the alloy and determination of the coefficients of Paris model.

Jan 1, 2010

By J. L. Chakravarty, S. K. Dutta, S. Banerjee, D. Putatunda

"General purpose uniprocessor systems used in control applications, however fast they may be, at a certain stage attain saturation, forcing the user or designer to consider other avenues for solving the problem. This paper gives a broad overview of multiprocessing with special reference to transputers. Virtually all aspects, from parallel systems real-time control to artificial intelligence (AI) and expert systems, have been highlighted. The application of transpurters in unilayer and multilayer control are discussed in detail, with specific attention to sensor integration. Two case studies describe at length the utilization of transputers. IntroductionIn conformance with the high level taxonomy of parallel computer architectures as given by Ralph Duncan(l) (an improvement to Flynn's classification, which maintains the essential elements of useful taxonomy based on instructions and data streams), the MlMD architectures are categorized into two groups: (I) shared memory, and (2) distributed memory type. While the shared memory multiprocessors are more popular than the message-passing multiprocessors because they can be programmed in a conventional sequential fashion, their aspect of the architecture creates a perfonnance bottleneck. In contrast, message-passing multiprocessors (MPM) suffer from no such limitation and can attain linear speed increases that are directly proportional to the number of processors put into use. The MPM implementation also has its own advantages and disadvantages. Because the performance of the system is heavily dependent on it, the interconnection strategy in a distributed memory MIMD machine is of paramount importance. The transputer(2.J), a multiprocessor node of the distributed memory type, is becoming very popular. The advantages offered by the transputer make its application in the mining and processing industries very promising."

Jan 1, 1994

By G. R. Gray, T. S. Chapman, J. L. Foster

THE wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as tragacanth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. INTRODUCTION It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.1-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-11 The wall-building properties of fresh-water muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods generally used in controlling filtration of fresh-water muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. LABORATORY INVESTIGATIONS Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester' at a pressure of 10o lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 c.c. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1941

By W. Kane, M. Karmis

Roof and rib failures in underground coal mines are one of the major problems facing the industry today. In addition to safety considerations, the resulting economic impact of such failures is staggering. Uncovering and replacing buried and damaged equipment and clearing entries can account for a large expenditure in lost man-hours and machinery. Yet, because of the complex nature of its formation, geological variability, and structural characteristics, coal mine roof strata is one of the least controlable of all mine design parameters. This is especially true along the leading (southeastern) edge of the Appalachian coalfields where considerable faulting and movement has contributed to hazardous coal mining roof conditions. During this research, a detailed study of several mines, in the southern Appalachian coalfields, was undertaken to determine the most prominent geomechanical factors affecting roof stability and to evaluate their influence in promoting unstable ground conditions. In order to accomplish this task, the major geological and geomechanical features found to be detrimental to coal mine roof within the Appalachian basin were identified and mapped in four Virginia mines. Statistical processing by chi-square and regression analysis was used to determine the influence of geology, mine-layout, and support methods on roof stability. It was found that some easily determined parameters can be successfully used to predict potentially unstable areas. A simplified roof classification system was developed based on these geomechanical parameters, which can be used to assess the stability of a particular roof type. A roof rating index was also devised capable' of expressing the probability of a failure under a given set geomechanical condition.

Jan 1, 1984

By E. L. J. Kleynhans, J. I. J. Fick, J. P. Beukes, P. G. van Zyl

"Ferrochrome (FeCr) is vital for the production of stainless and high-alloy ferritic steels, since it is the only source of new Cr units. FeCr production is an energy-intensive process. The pelletized chromite prereduction process is most likely the FeCr production process with the lowest specific electricity consumption (SEC), i.e. MWh/t, currently in operation. However, due to increases in costs, efficiency, and environmental pressures, FeCr producers are attempting to lower their overall energy consumption even further. Recently, it was proven that pre-oxidation of chromite ore prior to pelletization and prereduction significantly decreases both the SEC and lumpy carbonaceous reductants required for smelting. This paper presents the first attempt at conceptualizing the technoeconomic feasibility of integrating chromite pre-oxidation into the prereduction process. Financial modelling yielded a net present value (NPV) at a 10% discount rate of approximately R900 million and an internal rate of return (IRR) of approximatelyy 30.5% after tax, suggesting that the implementation of pre-oxidation prior to pellet prereduction may be financially viable. Sensitivity analysis indicated that the parameter with the greatest influence on project NPV and IRR is the level of prereduction. This indicates that the relationship between maintaining the optimum pre-oxidation temperature and the degree of prereduction is critical for maximium process efficiency. IntroductionStainless steel is a crucial alloy in modern society. Virgin chromium (Cr) units used in the manufacturing of stainless steel are obtained from ferrochrome (FeCr) – a relatively crude alloy consisting predominantly of Cr and iron (Fe) (Murthy, Tripathy, and Kumar, 2011; Beukes, van Zyl, and Ras, 2012). FeCr is produced mainly by the carbothermic reduction of chromite ore in submerged arc furnaces (SAFs) and direct current arc furnaces (DCFs) (Neizel et al., 2013; Beukes, Dawson, and van Zyl, 2010; Dwarapudi et al., 2013). The energy required to heat, smelt, and reduce the chromite ore to the metallized state is supplied by electricity (Pan, 2013). FeCr production is an energy-intensive process, with a specific electricity consumption (SEC) varying from 2.4 MWh/t to more than 4.0 MWh/t FeCr produced, depending on the process applied (Pan, 2013; Neizel et al., 2013). Daavittila, Honkaniemi, and Jokinen (2004) stated that the typical operational costs of FeCr smelters can be divided into four categories, i.e. chromite ore (30%), carbonaceous reductant (20%), electricity (30%), and other production costs (20%). This makes electricity consumption the joint largest factor that influences operational costs in FeCr production."

Jan 1, 2017

By Wayne T. Brooks

The Occupational Safety and Health Act of 1970, although providing no precise definitions of safe and healthful working conditions, specifies mandatory duties, and methods and procedures -- "to assure so far as possible every working man and woman in the nation safe and healthful working conditions." The dynamics of the workplace ad the dynamics of this coextensive Act both spring from the same source. Both require at any given time an application of the then con- temporaneous highest state of the art. Both are flexible, ongoing, adaptive, changing; both advance by a blending of experience and research.

Jan 1, 1972

By Fred D. DeVaney

Copper sulphate is a common flotation reagent for blonde ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation food may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it, is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss. That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.

Jan 1, 1929

By Henry C. Meeves

The Bureau of Mines, between 1956 and 1963, examined 18 major pegmatite districts in Arizona, Colorado, New Mexico, South Dakota, Utah, and Wyoming to evaluate their content of beryllium, a material in short domestic supply that has become increasingly important to modern industry. This examination report includes the salient statistics on the production of pegmatite minerals other than quartz and feldspar; and brief descriptions of 170 specific pegmatite deposits.

Jan 1, 1966