Search Documents

The eastern part of the state of Rhode Island on both sides of Narragansett Bay, including the island of Rhode Island, is underlaid with carboniferous rocks which carry veins of anthracite. This formation extends into the neighboring portion of Massachusetts, including the area from the state line, the towns of Mansfield, Brockton and Bridgewater,: and extending probably ten miles east of the latter two towns, to Middlesboro, and to Fall River. In Massachusetts the coal formation extends over nearly the whole of Bristol, and parts of Plymouth and Norfolk Counties. In Rhode Island and Massachusetts the area covered is about 400 square miles. In both states the exact limits of the coal measures cannot be determined on account of a thick layer of drift which overlays it. Along parts of Narragansett Bay, the coal measures outcrop in the cliffs on the west side of Rhode Island, and the presence of coal here seems to have been noted as early as 1760, and in 1768 a patent was granted to parties who "were about to dig after pit, coal or sea coal" at the back of the town of Providence. In 1807-08 Benjamin Silliman, later a geologist, visited some openings,' and in 1808 a mine was opened near Portsmouth, in the northeast part of Rhode Island. Work was done here until about 1814 when the mine was abandoned. No anthracite had been used in New England at that time, all coal used came from Nova Scotia, Virginia or England, and was high volatile bituminous; neither experience nor the means of firing favored the use of the local fuel? This mine was again working in 1827, was again abandoned and operations were resumed in 1847. In 1837 a note in a magazine mentions, "the immense coal mine in Cumberland-about six miles from the city of Providence" as having a shaft 14 ft. in diameter and 80 ft. deep, that the horses then used for hoisting the coal were to be superseded by a steam engine and another shaft was to be sunk. With these improvements 30,000 to 50,000 tons were to be produced the following year at a cost of $1 per ton and a sales realization of $6.1 Hitchcock's report refers to a number of localities in both states where definite knowledge of coal existed. These are:

Jan 1, 1942

By F. S. McNicholas

UNTIL the fundamentals of the physical behavior of rocks are completely understood, progress in block caving must proceed upon a cut and try basis. Criteria of rock failure are many and varied. If a rock mass behaved as a homogeneous isotropic solid, the problem would be greatly simplified. In practice we are never dealing with isotropic or homogeneous rock but with one that has been acted upon by geologic processes and which has pre-existing planes of failure. Under these complex conditions we do not find agreement. Actually there is little agreement between elasticians and physicists as to manner of failure in an isotropic homogeneous solid, although much progress has been made in the study of rock failure in recent years.

Jan 11, 1950

By Michael G. Nelson, Brandon J. Peterson

Currently, decisions made by mine management are usually based on economic analysis and predetermined rating systems and tables. As financial and other constraints on mining operations become more severe, more accurate methods are required. Discrete-event simulation programs have been used successfully in many mining applications, including the simulation of open-pit, truck-and-shovel operations. However, these simulations could not model complex systems well enough to provide the detailed modeling of the haulage roads and other mining operations that is needed today. The recent advances in computing technology combined with the recent abilities of simulation to realistically simulate complex systems and visually present results in 3D have made simulation a more detailed and valuable aid in the evaluation of mining projects.

Jan 1, 2002

By J. M. Karpinski, F. P. White, R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball, the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corp.'s Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about 50% without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1972

By B. E. Dindsale, P. B. Altringer, R. H. Lien

The Bureau cf Mines, U.S. Department of the Intericr, is investigating biolcgical and chemical deccntaminaticn of cyanide- containing leachates and residues. Biolcgical cyanide cxidaticn, using bacteria isolated from a precious metals tailings pond, destroyed >85 pct of the cyanide in several prccessing solutions containing up tc 280 ppm CN. Reaction time varied from about 4.5 hr in a trickling reactor using quartz as a bacterial substrate to 2 mo in unagitated, covered flasks. Chemical techniques were used to destroy the remaining complexed cyanide down to 1 ppm. Exploratory tests were also conducted using spent ore from heap leach operations as the bacterial substrate to determine if biological cyanide oxidation could be used to destroy the residual cyanide in spent heaps.

Jan 1, 1991

By H. R. Hose

The total crude fluorspar reserves in Western Europe, including the USSR and the Soviet sphere, Thetotalare estimated to exceed 17 million metric tons. The total fluorspar production in 1951 in Western Europe, excluding the USSR and Soviet sphere, amounted to 371,109 metric tons. The chief fluorspar-producing countries in Europe, excluding Russia and the Soviet sphere, are France, Western Germany, Italy, Spain, and the United Kingdom. TOTAL crude fluorspar reserves in western Europe, containing more than 35 pct CaF2, are estimated at 12 million metric tons, while reserves in the USSR and Soviet sphere may exceed 5 million metric tons. The bulk of these reserves are concentrated in the USSR, Spain, United Kingdom, Western Germany, and Italy. Since published estimates of the tonnages of individual mines and explored deposits are not available for most countries in Europe, the estimates given in Table I for individual countries are necessarily approximate, as they have been compiled from various sources and modified and combined according to the author's judgment. The majority of fluorspar deposits in Europe belong to the late Paleozoic metallogenetic epochs and have been found within or along the borders of the Hercynian massifs. Deposits in the Central and Esterel massifs of France, those of Western and Eastern Germany, Sardinia, the Catalonian coastal range and the Sierra de los Santos in Spain, and those of Devonshire and Cornwall belong to the Hercynian metallogenetic epochs. The deposits in southern Norway and Sweden belong to the middle Paleozoic or later, those of northern England to the late Paleozoic or later, those of northern Spain and Greece to the late Mesozoic, and those of northern and probably central Italy and Switzerland to the early Tertiary. Fluorspar occurs typically in veins, lenses, and stringers, but also in bedded replacement deposits and pockets, and may be colorless to white, yellow, green, pink, brown, blue, or purple to almost black. Except for the colorless variety, the only kind which can be used for the optical industry, the color of the fluorspar does not affect its ultimate use. Crystalline cubic or octahedral fluorite of CaF2 composition, with 48.9 pct fluorine and 51.1 pct calcium, has a specific gravity of 3.18. The ore in place, however, usually averages 3.0 metric tons per cubic meter owing to the quantity of other minerals asso- ciated with the fluorspar in the veins and the physical state of the fluorspar, which may vary from sugary to massive crystalline or microscopic inter-growths with barite or quartz. Barite of 4.5 sp gr, quartz of 2.66 sp gr, and chert and calcite are commonly associated with fluorspar. Other minerals usually present in lesser amounts are celestite, wad, silver, lead, zinc, copper, iron, and uranium minerals. In some cavity fillings the rhythmic deposition of the fluorspar, barite, and quartz into successive crusts may make it possible to handpick the crude ore on belts or to separate the fluorspar from other minerals while the actual mining is carried on. Where metallurgical grade lump spar is required for foundries, separation of quartz and barite may be made also by jigs and heavy media, and in some mines the lead and zinc sulphides may be separated and recovered by vibrating tables. However, except in the case of unusually high grade deposits, acid grade fluorspar is obtained by flotation. By this process fluorspar deposits grading down to 35 pct CaF2 in the crude ore can be worked at a profit when fluorspar, lead, zinc, and silver prices are high, as the sulphides of these ores can be separated from the fluorspar by flotation and concentrated.

Jan 1, 1956

By Marco D. Boscardin

During subsidence, the ground surface may settle, change slope, change curvature, go into tension, and/or go into compression. In response to these ground movements, buildings and buried utilities in the subsidence area may settle, tilt, bend, distort, and sustain extension, compression and/or torsion. In order to develop measures to protect existing structures and utilities, or to design new structures and utilities to withstand potential movements in areas of subsidence, it is necessary to understand the interaction between the ground and the building or buried the utility. This paper reviews subsidence-induced ground movements, how these ground movements are transmitted to and accommodated by buildings and buried pipelines, and how these structures may alter ground movements relative to free field subsidence-induced ground movements.

Jan 1, 1986

There are many risks associated with the storage of nuclear or other toxic wastes. One of the major risks is the escape of material from the repository. No matter how well a storage facility is engineered, the potential escape of dangerous material must be studied. This kind of study will include some estimation of the "travel path" of the particles. The travel path of a radio-nuclide particle will depend on the geological and hydrological parameters of the surrounding rocks. These parameters must be estimated from a limited number of samples available within the study area. Any estimation will -of necessity -contain a certain amount of uncertainty or "estimation error". This uncertainty will be carried through to the analysis of potential movement of particles, so that the estimated travel path itself will be subject to some error. This paper discusses an approach which may lead to a quantification of the uncertainty on the predicted travel path.

Jan 1, 1989

By Seunghoon Lee

The increase in the number of higher and larger buildings is expected to require the buildings' outer wall maintenance process, which includes cleaning, painting and monitoring, still depends on manpower. In this study, we proposed the robotic building maintenance system and aimed to reduce the jerk effect through the motion control of the system, improve the performance of the maintenance task, and ensure longer life and safety by improving the stability of the building structure and robot system. Through the results of the motion control and field-test with the proposed system, in specific, horizontal sliding module (HSM) showed that the jerk oriented by impact force was significantly reduced, feasibility of the proposed method was verified, and the robotic challenges were explored.

Aug 1, 2013

By Denise Crocce Romano Espinosa, Andrea Moura Bemardes, Jorge Alberto Soares Tenorio, Daniella Cardoso Buzzi, Tatiana Scarazzato

"In copper plating processes, a fraction of raw materials are incorporated to the final products, while other portions are discarded as effluents. In this study, the application of electrodialysis (a membrane treatment process) was studied for treatment of wastewaters from cyanide-free strike baths, in order to reuse the components of this bath: copper and HEDP. The synthetic solutions studied consider 1 % of ion concentration of the bath used in this process, simulating the rinsing waters to be discarded. The electrodialysis allowed a percentage extraction up to 73% of copper ions and 72% of HEDP from the effluent. Complexes formation between the acid and copper indicates the possibility of recovery of components in the same compartment, obtaining a concentrated solution of these substances that can be reinserted in the process, for compensating drag-out losses. A diluted solution is also obtained, that can be reused as water in rinsing tanks.IntroductionIn metal finishing industries, contaminants in wastewater and the type of treatment required are determined according to the type of operation [l]. Generally, electroplating industries employ conventional wastewater treatments, e.g. oxidation of cyanide and chemical precipitation. This stage promotes reactions with soluble compounds to produce an insoluble precipitate, removed by physical separation. The sludge is dried by press-type filters [2].In this manufacturing sector, part of the raw materials are discarded as hazardous waste. The cost of discarded compounds and the treatment and disposal of waste may compromise profit margins. In addition, water consumption per unit of production stimulates the development of methods able to recover and reuse the largest possible amount of water [3].In some plating processes, cyanide-based substances are used as complexing agents and as raw materials in form of metal salts [4]. However, the toxicity associated with cyanide has been promoting research for the development of new raw materials in plating processes.A study conducted in Brazil [4] evaluated the modification of a commercial cyanide-free bath for processes of copper coating on Zamak. In the performed study, a new alkaline copper bath was formulated using l,hydroxyethane-1,1-diphosphonic acid (HEDP), an organic compound known for forming stable complexes with metal ions.As results of the study, the operational conditions and the formulation of a bath to obtain adherent, uniform and bright layers were established (Table I) [4]."

Jan 1, 2014

The most common method for identifying the potential for blast damage is the peak particle velocity. But this can depend on many factors such as the type of blast, explosive, confinement, timing and the rock mass. The value must then be used to estimate damage. But the amount of damage will depend on the rock mass quality and the excavation size and shape. The amount of damage that can be accepted will depend on the purpose of the excavation. This paper presents a logical, but very approximate, procedure that the mining engineer can follow in order to assess the potential for damage in the control of that blasting.

Jan 1, 1987

By G. M. Ritcey

The design of the plant facilities together with the necessary equipment required for the operation is at an optimum only for the specified plant with its peculiar priorities and preferences. Because many alternatives in design are possible to suit a particular plant, each plant designer and contractor must choose carefully in the selection of the site, design and choice of materials of construction, as well as the type of equipment necessary for the process. Basic factors as efficiency, dependability, simplicity, and safety must be considered early in the construction; while the choice of equipment, materials of construction, possible corrosion problems, automation, maintenance, effluents disposal and tailings dam construction can greatly affect the plant costs. While existing plants are in operation, the know-how gained from the operating experience of those plants can be invaluable in the new plant planning, design, and construction.

Jan 1, 1978

By J P. van Dyk

The dramatic strengthening of the rand against the dollar as well as a decline in quantity and quality of locally available concentrates have had a dramatic impact on Zincor?s operations during the previous two years. Zincor has responded with the implementation of a number of technical improvements to the process to decrease cost and increase revenue and plant flexibility. Among the initiatives is the pre-leaching and pelletising of the zinc concentrate, de-bottlenecking and process improvements in the leach and purification circuits, the introduction of cathode washing and automated cathode stacking in the cell house and the installation of a new furnace to produce pre-alloyed jumbos. This paper will describe these initiatives and others that Zincor have recently taken to stay competitive in changing global base metals market.

Jan 1, 2005

By Joseph J. Poveromo

The blast furnace today continues as the primary production method of hot metal in large-scale steel production. The blast furnace process has been the target of repeated attempts to replace it with various process options, including direct reduction and coke-free smelting reduction. While these new technologies are being adopted in appropriate niches, the blast furnace has responded to the challenge by being amenable to continuous improvement. I will review the role of the blast furnace, major developmental and improvement trends, and then list the current important issues in ironmaking. I will outline the challenges to be faced by the blast furnace to maintain its position as the primary hot metal production process. The material presented here is an update of earlier presentations made in Stockholm, Sweden, 1996, Duluth, 1998 and Chicago, 2000.

May 1, 2003

By Geo. A. Wells

Abstract The consumption of barytes in certain paints polyurethane foams, seamless, flooring, glass, brake linings, plastisol caskets for food containers and in fluids used for gastrointestinal X-ray examinations rely on tie unique properties of barium sulfate, There are no readily available mineral substitutes. Barytes are also the essential raw material for the manufacture of industrially important barium chemicals. High quality barite ore has become scarce throughout the world. Processing ore into quality end products is both capital and energy intensive. These factors have tended to limit availability and increase prices which have encouraged the use of alternates and restricted market growth.

Jan 1, 1980

By D. B. Dow

This report on methods employed for dehydrating oil-field emulsions, is the second of a series prepared as a result of a study of oil-field emulsions recently completed by the writer. The first paper2 dealt with the factors responsible for the formation of emulsions. A third paper will discuss the physical chemistry involved in the formation and resolution of such emulsions. In the early development of the oil fields of Pennsylvania, no emulsion troubles of any consequence were encountered, nor to any serious extent in the oil fields of other Eastern States: However, with the development of fields west of the Mississippi in Oklahoma, Kansas, Texas and California, where heavier oils of different characteristics were found, the problem of dealing with cut oil soon became of great importance.

Jan 1, 1925

By Craig J. Brown

Despite its great potential utility, ion exchange has only achieved limited application in hydrometallurgy. To a significant extent this is due to the limitations of conventional ion exchange process design as well as the properties of the ion exchange resins themselves. Over the past decade several new ion exchange resins have been introduced with properties that make them potentially very useful for various hydrometallurgical separations. In addition, a novel ion exchange process called Reciprocating Flow Ion Exchange or Recoflo, which has been employed in the metal finishing industry for the last dozen or so years for chemical recovery and effluent treatment, has been shown to offer a number of unique and significant advantages over conventional I.X. technology.

Jan 1, 1984

By T. Zoltai

Asbestos is a generic term for industrially useful fibers recovered from exploitable deposits of the asbestiform varieties of five silicate minerals: chrysotile, anthophyl-lite, actinolite-tremolite, cummingtorute-grunerite, and rie-beekite. Asbestos and asbestiform fibers of some other minerals are known to be carcinogenic. Minerals crystallized in the asbestiform habit-are characterized by unique properties (morphology, strength and flexibility, physical and chemical durability, and defect-free surface structures). The key to the unusual properties, and health effects, of asbestiform fibers appears to be in their unusual surface structure. In contrast, non-asbestiform crystals of the same minerals, including the five so called asbestos minerals, do not have these properties and are not carcinogenic.

Jan 1, 1989

By J. L. Huitt, IM. L. Slusser, E. E. Glenn, M. L. Slusser

This paper is concerned with: (1) an analysis and interpretation of the filtration characteristics of drilling muds on filter paper, and (2) an interpretation of early stage "filtration" on consolidated synthetic porous media, herein referred to as the "surge loss" period. It is shown that water-loss data can be plotted so as to disclose the existence of a surge period, a non-uni-form cake thickness period, and a constant pressure filtration period. The same periods occur during exposure of consolidated porous media to muds. The data on consolidated porous media indicate that: (1) mud particles bridge pores inside porous media during the surge period, and (2) "filter cake" build-up inside porous media occurs during subsequent filtration. The data also show that the surge loss increases with sample permeability and with pressure differential. INTRODUCTION The phenomenon of mud filtrate invasion into porous sands of a drilling well has been recognized for many years.1,2,3,4 Part of API Code 29 is concerned with the filtration testing of a drilling mud to yield data on this subject. In a number of investigations "plastering properties" of muds were studied,5,6,7,8 "plastering" apparently meaning cake forming properties. In such studies the characteristics (thickness, permeability, and toughness) of the cake and the rate at which the liquid phase of the mud was separated from the solids (filtration rate through the cake, commonly referred to as water loss) were measured or at least considered. From the standpoint of its effect on well productivity, filtrate invasion into "clean" water-wet pay sands (i.e., those containing no clay minerals) may not necessarily be a serious problem. An increase in water saturation in the zone immediately around the wellbore would cause loss of oil permeability. However, in such a system, much of this water may be removed by oil production. If filtration occurs into "dirty" sands (i.e., those containing appreciable clay minerals), clay swelling or other mechanisms may cause losses in oil permeability which cannot be overcome by oil production.'.' The phenomenon of mud particle invasion into the pay sand of a drilling well was considered to be a possible serious factor in the early days of rotary drilling. Opinions varied as to whether drilling fluids "mudded up" and "sealed" oil sands. In 1932 Rubel,9 Gill,10 and Parsons," in separate papers, presented differences of opinion together with some laboratory and field data concerning loss of oil production caused by drilling fluid invasion into pay zones. These papers, and the discussions, furnish a large background on this subject and indicate the very clear thinking of many men at a time when petroleum production technology was in its infancy. Jones and Babson,6 and Silent,' experimentally found that the depth to which mud particles invaded water-saturated sand packs was small (no greater than 1/16 in). Arn-quist12 in 1937 observed loss of water permeability due to invasion of mud particles into water-saturated, consolidated, sandstone samples. Williams and Cannon5 studied the filtra-tion properties of drilling muds and mentioned "sludge" which penetrated a short distance into the water-saturated filtering medium (sand pack). Byck5 concluded that formation permeability had no effect on the plas-

Jan 1, 1958

By J. C. M. Li

This exploratory survey was undertaken to repeat some experiments- in which anomalous results were reported1 for bismuth and to measure the thermoelectric power of some bismuth alloys and inter-metallic compounds. sato1 reported that the thermoelectric power of bismuth depends on the temperature gradient. This seems rather unreasonable especially when the Benedicks effect' has not been detected. Even if the material is not homogeneous, the observed thermoelectric power can be represented by

Jan 1, 1959