Search Documents

The process selection and design aspects to treat primary ore in a new carbon-in-pulp (C.I.P.) plant while utilizing, where possible, existing equipment and infra- structure are discussed. The existing crushing plant, water supply, reagents, laboratory and infrastructure facilities from the heap leach have been upgraded and expanded to meet the C.I.P. plant requirements. The new power supply is from the North Queensland grid system. A series of metallurgical tests was carried out and a review of the data showed that the primary ore was amenable to conventional cyanide leaching. Following feasibility studies, a new process plant which included grinding mills, leaching, and adsorption tanks, thickener, desorption and gold roam facilities was constructed.

Jan 1, 1989

By T. D. Oulton

The only known attapulgite clay deposits of any considerable extent and purity in the United States are roughly bisected by the Georgia. Florida state line between Decatur County, southwest Georgia, and Gadsden County, northwest Florida. Although attapulgite clay occurrences both farther East and South are known and have been mined to some extent in the past, at the present time it can be said that substantially: all of the commercial attapulgite clay mining and pro¬cessing is concentrated in a roughly rectangular area some 25 miles long by 15 miles wide,, in the general region of Attapulgus, Georgia, and of Quincy and Havana, Florida. Within this area are located the clay processing plants of the four major producers as well as most, if not all, of the currently active mining operations. The approximate location of the plants and of some of the open mines are shown in the local area map, Figure No. 1, for the purpose of orientation only.

Jan 1, 1965

Everyone knows the importance of careful handling of explosives. Even so, the point is on occasion all too graphically driven home. Witness the recent blast at a Utah explosives plant that killed five people. Part three of this series on explosives discusses transportation, storage, handling, and destruction. Federal, state, and sometimes local regulations govern the many steps involved in transporting, storing, and handling explosive materials. Regulations minimize personnel exposure to hazardous material and insure that the explosives remain stable and usable.

Jan 9, 1981

By W. C. Ashby, C. A. Kolar

Extensive reclamation experience in the midwest dates from the 1930s with trees, from the 1950s with pastures, and from the 1970s with row crops. Superior growth and productivity of mined land over unmined land can be shown for forest and pasture, related to type of rooting medium after mining and kinds of plants gown. Superior reclamation to crops is actively being studied. Recent regulations have greatly altered the potential for superior growth of trees, pastures, and crops.

Jan 1, 1984

By D. L. Passmore, J. D. Bennett

The degree of injury and days lost from work due to an injury are examined for selected electrical sources, occurring in conjunction with falls of the injured miner or with selected machinery, that could have been eliminated by use of diesel equipment. Although the number of preventable electrical source injuries is small relative to the total number of injuries during the period examined, many lost-time injuries could have been precluded and thousands of days lost from work could have been avoided.

Jan 1, 1986

By John A. Herbst

Mineral processors have evolved from "handbook-based" decision makers to "model-based" decision makers. With this evolution have come significant improvements through increasing productivity, decreasing capital and operating costs and increasing product quality. This paper traces the development of model-based decision-making technology over the last 40 years and documents the benefits resulting from systems optimization using these tools. Some speculation is ventured concerning the future of model-based decision-making tools and their use in the field of mineral processing.

Jan 1, 2000

By Kedikilwe Oageng

Effective perimeter control during drilling and blasting is critical not only to blasting results but also to the overall stability of the pit over its entire life span. A pit where perimeter control is not given enough attention when conducting drilling and blasting operations, often experiences over-break or back break beyond final pit wall limits, and therefore has a relatively high probability of failure. Such a pit also becomes unsafe, sometimes not easily accessible, has increased loading costs due to production of oversize, longer cycle times and often problems are encountered when blasting subsequent benches. All these are undesirable consequences, which have negative cost implications. Specialised blasting techniques such as trim blasting and pre-splitting have over the years proved to be effective perimeter control measures. However, the success of these techniques is directly attributable to the time and effort given to the processes. This paper presents results of a project undertaken to monitor, review and optimize the trim blasting and pre-splitting processes at Orapa Diamond Mine in Botswana. The project was specifically incepted to improve the final wall conditions, which continued to deteriorate due to persistent over-break during blasting. The paper also analyses the results obtained against a benchmark of results taken prior to project implementation. Specific blast design parameters which are critical to blasting results were identified as problem areas after auditing of the pre-implementation drilling and blasting practices. These include drill-hole depth, spacing, splitting factor for pre-splits and timing of trim blasts. The impact of different rock types on the results was also studied, and recommendations were made at different phases of the project and results obtained after implementation analysed until optimum results were achieved.

Jan 1, 2008

A description is given of a detailed examination of a coal bore core and of attempts to predict properties of equivalent "as-mined" coal using the bore core data so obtained. The accuracy of the prediction was measured by testing independently a large sample of coal which was produced under near mining conditions from a site adjacent to the bore core. Very encouraging results were obtained particularly in the prediction of size and ash distributions and washability characteristics of run-of-mine Coal.

Jan 1, 1972

By M. E. Hassan, J. C. Calhoun, R. F. Nielson

An apparatus was constructed for the measurement of inter-facial tensions over a range of temperatures and pressures. This apparatus utilized the pendent drop method, and resembles in construction similar apparatus recently described in the literature and in use in some petroleum research laboratories. The interfacial tensions of benzene, propane, n-pentane, n-hexane. n-octane. and iso-octane against water were measured at temperatures ranging from 26" to 82" C and at pressures ranging from 1 to 204 atm. Values of interfacial tensions for the henzene-water system and their variations with temperature and pressure are generally in good agreement with value? of previous investigations. The data in all cases showed a slight decrease of interfacial tension with pressure at constant temperature in the range studied. The effect of pressure became less as the pressure was increased, with an indication of a reversal of the effect at higher pressures. There was a decrease of interfacial tension with temperature at constant pressure in all cases, as would normally be expected. This rate of decrease became greater the higher the temperature. A general equation is presented for the interfacial tensions as a function of presPurp and temperature over the range studied, and the constants calculated for each system. A definite trend was found in the effect of molecular weight on the interfacial tension at a given temperature and pressure, for the homologous series from propane to n-octane. Data for n-decane from the literature fitted well into this trend. INTRODUCTION It has been recognized for many years that surface forces play an active part in the production history of an oil reservoir as well as in determining the amount of unrecoverable oil. The magnitudes of these forces are governed by the values of the interfacial tensions. These vary greatly with composition, pressure, and temperature. The effect of composition is greater than that of pressure and temperature over the ranges normally encountered. In fact, because of the variety of compounds present in a crude, no attempt has yet been made to correlate crude composition with its surface tension or with its interfacial tension against water. The amount of dissolved methane greatly affects the surface properties of an oil, and there are "surface-active" compounds in crudes which have a much greater effect on boundary tensions than do equal amounts of hydrocarbons. The purpose of the present work was partly to contribute data that would eventually be used in correlations applicable

Jan 1, 1953

Over the past decade most, if not all participants in the resources sector have been involved in initiatives to improve margins, reduce costs and improve business profitability. In many cases the initiatives undertaken have fallen short of their stated objectives, and in some cases have resulted in the terminal decline of the underlying business. In reviewing why many such initiatives fail, a common theme of arbitrary cost reduction and a focus on minimising cost as opposed to maximising value and cashflow emerges. This paper proposes a structured process that allows mine owners and managers to develop an understanding of their cost structure and optimise production and cost outcomes from the business. The broad objective of cost optimisation is to create value by getting more out of existing and new assets by focussing on operational areas, particularly production and maintenance. The paper uses practical examples to highlight the application of cost driver trees as a mine improvement tool.

Jan 1, 2002

Discussion of the paper of Robert Franke, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1201 to 1205. ARTHUR 0. GATES, Lafayette, Ind. (communication to the Secretary*) :-In connection with the comparison of mechanical crushing efficiencies in Tables I and II of Mr. Franke's paper, I wish to suggest a somewhat simpler way of making this' comparison, based upon what the writer has called the "crushing-surface diagram," as published by him in the Engineering and Mining Journal for May 24, 1913. Such a diagram, based on the data given in Table II, is submitted herewith, Fig. 1, cumulative percentages being plotted as abscissas and reciprocals of diameters (theoretical mesh per inch). plotted as ordinates.. Such a diagram averages the diameters without calculation, and areas upon it are proportional to surface produced, and, in accordance with Rittinger's law, to energy spent on crushing alone.

Jan 11, 1913

By R. D. Leitch

The pollution of streams by acid mine drainage has become of great importance in the past few years in certain regions of the United States. Large quantities of acids are used in a discharged from other industries than mining, notably in tube, sheet, tin-plate and era hell inn works. These are usually less important then coal mines as a source of acid drainage, because of their more limited distribution throughout the States most affected by acid waters and their relatively smaller numbers. Streams are naturally alkaline and are, therefore, able to take care of rather large quantities of acid wastes, but when such enormous quantities as are often found in mining districts enter the streams, the natural alkalinity is quickly overcome. When a neutral or almost neutral condition has been reached, the further addition of a relatively slight quantity of acids will cause a great difference in the quality of the water.

Jan 1, 1926

Provide an accurate, simple, alternative means of evaluating the safety of mine electrical ground systems which has little or no negative impact on mine productivity. The Traditional Evaluation Method The Code of Federal Regulations requires all mines to safely ground their power systems to earth. Effective earth grounding reduces shock hazards to mine workers operating electrical equipment, protects equipment from damage by voltage transients, and provides a means of detecting and locating ground faults. Once an earth ground bed has been constructed, its level of resistance has traditionally been used to gauge the safety of the entire grounding system. Bed resistance measurements are normally performed using a ?fall of potential? technique with a current return electrode placed at a remote location, If the resistance measured is acceptably low, then the bed is assumed safe.

Jan 1, 1985

By Gordon R. Luster

Mineral-processing plants commonly rely on homogenization and proportioning facilities to reduce the variability of incoming raw materials and to blend different materials together to satisfy quality specifications. To determine appropriate designs for these facilities, plant designers need information about the variability of the mined materials, measured as the materials enter the plant. But if the materials to be mined in the future differ greatly from those used in the past, only information extracted from exploratory drilling of the materials in the around may be available. Fortunately, useful information for plant design may still be obtained by combining simulated mineral deposits with simulations of likely mining procedures. The output of a mining simulation is a time series of simulated raw-material characteristics that should mimic the behavior of the real materials to be delivered to the plant in the future. This paper shows how conditional simulations of coregionalized ore grades can furnish information useful in the design of homogenization and proportioning systems.

Jan 1, 1986

Capture airborne coal dust generated by a continuous mining machine to reduce workers? dust exposure and to improve face visibility. Approach Develop a low-profile dust collector system which can be mounted on the boom of a continuous miner. How It Works When coal is mined with a milling head continuous miner, a substantial amount of coal dust (respirable and non-respirable) escapes the dust suppression sprays at the cutter head. This can cause poor visibility around the cutting head and can expose the workers to high levels of respirable dust. A practical means of removing this dust is with a scrubber mounted directly on the mining machine. Under a Bureau of Mines contract, a low-profile, machine-mounted dust collector (MMDC) was developed to avoid adding extra height to the continuous

Jan 1, 1983

By Steve Naruk

Microscopic point-count analyses, although time-consuming, provide detailed mineralogical information which is not obtainable by any other means. Such information can be invaluable for evaluating mill circuit behavior. In comparing two months of operation of a Cu-Pb-Zn sulfide flotation circuit, chemical analyses show that higher copper recoveries and concentrate grades were obtained from lower grade ore, but they provide no explanation of how the improvements were obtained. Quantitative micro-scopic analyses, on the other hand, show the following: 1. There was no change in the identity of the Cu-bearing minerals. 2. Increased copper recovery was achieved primarily by increased recovery of chalcopyrite middling particles. 3. The increased recovery of chalcopyrite middling particles also increased the amount of gangue entrained as locked particles. 4. Increased rejection of free gangue particles, particularly those finer than 25 microns in size, resulted in a net decrease in gangue content.

Jan 1, 1981

By N. A. Zeigler, T. D. Yensen

Aging is a term that connotes a slow change in properties under ordinary operating conditions. It can be accelerated by increasing the temperature and by mechanical straining. The magnetic properties of iron and some of its alloys have for many years been known to be subject to such a change. But the cause of the change was not recognized until a few years ago after mechanical age-hardening in non-ferrous alloys of the "duralumin" type had been definitely shown, by means of solid solubility curves, changes in electrical resistance and microanalysis, to be caused by slow precipitation of one or more constituents from the solid solution. The similarity between the solid solubility curves of such alloys (Fig. 1) and those for iron-nitrogen (Fig. 2) and iron-carbon alloys (Fig. 3) below the A1 transformation point suggested at once that magnetic aging of iron might be caused by a similar process; namely, by the slow precipitation of carbon and nitrogen in the form of Fe4N and Fe3C at ordinary temperatures because of a cooling rate that had been too rapid to permit complete precipitation according to equilibrium conditions. This suggestion has since been amply confirmed, particularly by the comprehensive work of Köster1 on the effect of nitrogen and carbon. Typical curves are shown in Fig. 4 for the relationship between aging temperature and coercive force. Previous to the establishment of the precipitation-hardening theory it was thought that the effect of nonmetallic elements like C, N, O, etc., on the magnetic properties of iron was greatest when these elements were retained in solid solution, atomically dispersed throughout the interstitial spaces of the iron lattice2. Based on the theory that magnetic properties are intimately connected with the regularity of the lattice, it now follows quite logically that a greater effect on this regularity may be obtained when the above impurities are precipitated as very fine particles of Fe3C, Fe4N, FeO, etc., more or less uniformly dispersed within the grains. But if this is the case, it follows also that there must exist a relationship between the size

Jan 1, 1935

By N. A. Zeigler, T. D. Yensen

Aging is a term that connotes a slow change in properties under ordinary operating conditions. It can be accelerated by increasing the temperature and by mechanical straining. The magnetic properties of iron and some of its alloys have for many years been known to be subject to such a change. But the cause of the change was not recognized until a few years ago after mechanical age-hardening in non-ferrous alloys of the "duralumin" type had been definitely shown, by means of solid solubility curves, changes in electrical resistance and microanalysis, to be caused by slow precipitation of one or more constituents from the solid solution. The similarity between the solid solubility curves of such alloys (Fig. 1) and those for iron-nitrogen (Fig. 2) and iron-carbon alloys (Fig. 3) below the A1 transformation point suggested at once that magnetic aging of iron might be caused by a similar process; namely, by the slow precipitation of carbon and nitrogen in the form of Fe4N and Fe3C at ordinary temperatures because of a cooling rate that had been too rapid to permit complete precipitation according to equilibrium conditions. This suggestion has since been amply confirmed, particularly by the comprehensive work of Köster1 on the effect of nitrogen and carbon. Typical curves are shown in Fig. 4 for the relationship between aging temperature and coercive force. Previous to the establishment of the precipitation-hardening theory it was thought that the effect of nonmetallic elements like C, N, O, etc., on the magnetic properties of iron was greatest when these elements were retained in solid solution, atomically dispersed throughout the interstitial spaces of the iron lattice2. Based on the theory that magnetic properties are intimately connected with the regularity of the lattice, it now follows quite logically that a greater effect on this regularity may be obtained when the above impurities are precipitated as very fine particles of Fe3C, Fe4N, FeO, etc., more or less uniformly dispersed within the grains. But if this is the case, it follows also that there must exist a relationship between the size

Jan 1, 1935

By J. F. Stenebråten, W. P. Johnson, D. R. Brosnahan

Carbonaceous material (CM) from ores of varying preg-robbing activity from Barrick Goldstrike Mines Inc. (BGMI), Nevada, was characterized in terms of its functional group content, hydrocarbon content, elemental composition, and humic acid content. FT-IR analyses showed neither the presence of hydrocarbons nor of carboxylic, phenolic, or sulfhydrol functionalities. FT-IR bands present included C=C stretching in aromatic rings and C-O-C stretching, indicating presence of oxygen as ether linkages in the carbon matrix. Calculated atomic oxygen to carbon (O/C) ratios did not reveal a trend between maturity of CM and preg-robbing behavior, possibly due to low resolution of electron microprobe analysis. However, the atomic O/C ratios agree with other chemical analysis, indicating that the organic carbon is very mature, similar to or higher in grade than anthracite coal.

Jan 1, 1999

By W. R. Toeplitz

H. N. Ghenn.*—It has been established that the accuracy obtainable from any precision machine is a function of the wear resistance, maintenance and closeness of fit of the bearings, hence I would like to ask Mr. Toeplitz how these oil-less bearings compare with cast iron or babbitt or similar materials when used on precision machinery. Could these bearings be used, for example, on a grinding machine in which work must be held to a tolerance of plus or minus 0.000025 inch? W. R. TOEPLITZ.—The metal-powder bearings can be held to very close tolerances and are used in place of cast iron and babbitt on precision machinery.

Jan 1, 1945