Search Documents

By R. B. Schluter, M. M. Fine

The Bureau of Mines' Twin Cities Metallurgy Research Center has of late concerned itself with reduction-induration of iron ore. One development provided a flowsheet for the agglomeration of green concentrate pellets in a reducing atmosphere created by a solid reductant external to the agglomerate. The product pellets were well metallized and physically competent. Maximum recommended operating temperature was 2100º F. In these studies, it was observed that unflred iron ore pellets indurated in a bed of anthracite or certain lignite chars frequently acquired exceptional crushing strength. A diagnosis of the phenomenon revealed that sulfur in the fuel was the probable cause. Accordingly, a research program was established to test this premise and to put it to practical use. Gaseous reductants were employed initially because of the ease and accuracy with which they could be metered.

Jan 10, 1969

By Cristian Rodriguez, Tom BoBo, Maria Rocha, John Kemeny

Blast fragmentation depends on many factors. First of all, it depends on the specific blast design, which includes the amount and type of explosive, the blasting pattern, the timing and sequencing, and other parameters. Secondly, it depends on the properties of the rock mass, including the uniaxial compressive strength (UCS), the rock mass elastic modulus (E), the rock discontinuity characteristics (as reflected in the GSI or RMR), and the rock density. Several fragmentation models have been proposed to predict blast fragmentation based on the blast design and the properties of the rock. These models include the Kuz-Ram model and variations of this model, as well as recent models by Kim and Kemeny (2011) and others. Fragmentation models are validated and calibrated by comparing the predicted fragmentation with actual post-blast fragmentation from image processing monitoring systems.

Jan 1, 2014

By M. C. Lavine, H. C. Gatos, R. S. Mroczkowski

The structure of GaAs-Ge heterojunctions prepared by a back-melting process was studied by X-rav diffraction, melallographic, and electron-micro-analyzer techniques. The boundary region between the GaAs and the germanium was found to consist of a four-layered band. A discontinuity between the two inner bands was brought about by solidification occurring simultaneously from the GaAs and the germanium side. The junction material OH either side of the central discotinuity was found to have grown as a single Crystal with the orientation of the parent substrate. It was found essential to determine the GaAs-Ge phase diagram. This was accomplished by a series of alloys containing 0 to 40 wt pet GaAs. Over this range the diagram is a simple eutectic with the eutectic point at 74 wt pet Ge and 845 C. The limiting- solubility of Coils in germanium was found to bc less than 5 wt pet. The Kossel divergent-beam X-ray technique was used to study orientation relationships across the boundary lager. A great deal of effort has been recently expended on the electrical properties of heterojunctions. Little attention, however, has been given to the metallurgical variables which may be of importance in the formation of the junctions. The present work was undertaken to investigate some of the more pertinent metallurgical aspects of interface-alloyed GaAs-Ge heterojunctions. Such parameters as solidification processes, composition gradients, orientation effects, and the accommodation of crystal structures have been the objects of study in this program. EXPERIMENTAL PROCEDURES Phase Diagram. The phase diagram of the GaAs-Ge pseudobinary system was determined by means of cooling curves. A Bridgeman furnace was employed with the center section maintained at 1200°C and the upper section at 800°C. Melts varying from 0 to 40 at. pct in GaAs content were used. Each charge was incapsulated under a two-thirds atmosphere of argon in a carbon-coated quartz tube. Five min in the furnace hot zone provided rapid melting and homogenization. The capsule was then removed to the cooler portion of the furnace. Cooling times were of the order of 3 min. The resulting homogeneous microstructure indicated that equilibrium conditions were obtained by this procedure. Formation of Heterojunctions. Rectangular parallelepiped single-crystal samples were cut with the large faces of either the (l00), (110), or (111) orientation. The remaining four surfaces were also cut to specific orientations to permit accurate relative orientation of the GaAs-Ge pairs. The

Jan 1, 1965

Evolution of Maintenance Practices. Mechanization processes in underground mining operation became stronger in the 70?s - 80?s. Did maintenance practices changed over the years ? What are the the major differences of today?s practices? Speaker, Robert Hamilton Working at different positions into maintenance organization since over 25 years, Robert has accumulated a various and rich experience of ways to maintain equipment. He started as mechanic on construction projects and open pit mines. Early in his career Robert had supervision's responsabilities. He started in open pit operation (QCM) and after in underground operation with Lac Minerals, working at Bousquet, Doyon and Louvicourt mines, as U/G mechanical foreman and mechanical general foreman, and Maintenance superintendant with Cambior . He also experienced the underground mines equipments supplier's side working with Sandvik Canada.

Feb 1, 2008

By Larry J. Tucker

INTRODUCTION The orebody at Pea Ridge strikes NE-SW and dips at about 800 to the SE. The ore and surrounding rocks are Pre-Cambrian in age. These rocks are usually very competent. Locally strong jointing has caused problems and toward the hangingwall dikes have caused particular problems during or after the open stoping phase of production. About 396 m of sediments lie over the ore. The shape and mineral content of the orebody has been fairly consistent so far with production areas lying from the 1375 to the 2475 levels. The deeper limits of the ore- body haven't been found yet. The ore is high grade magnetite with a strike length of over 600 m and a maximum width of over 180 m on some levels at the center of the orebody. Production at Pea Ridge for the first three years of operation came from two types of open stopes. The original stopes were recovered with horizontal production rings being drilled and blasted from vertical raises. Later a more typical sublevel stoping method using vertical production rings from one or more drilling sub- levels was used. There were a number of reasons for the selection of open stoping as the initial production method at Pea Ridge. First, it was judged that the ore was not of a block cave quality. After fifteen years of production, this assumption can be verified. There was some concern during the planning days for the potential for high flow rates of water into the mine from aquifers in the sediments lying over the orebody. Dewatering wells from surface and underground were put in as a precaution and nothing came of this potential problem. Open stoping and its resulting pillar structure put off this problem by supporting the sediments a few years longer. For a moderate investment in level development some production from open stoping was quickly realized. The first open stopes were brought in on what was then the bottom mine production level (2275), near the shaft pillar and situated on the footwall. This production practice of stoping on the heels of development from shaft pillar westward and from footwall to hangingwall continued through the open stope phases of production at Pea Ridge for many years. From the standpoint of mine efficiency and pillar stability, this would not seem to be a recommended mining practice. 74 570 w electric slushers, using 1.37 m dippers, pulled the open stope ore out into 18 ton bottom dump cars. Ordinarily five of these cars made up a train, which was pulled to the dump area by a trolley powered electric locomotive. Open stoping had the disadvantage that 100% of the recoverable portions of the orebody had to be developed in order to recover 33% of the ore. 67% of the ore was left behind in a large pillar system. For many years we had no planned method for recovery of these pillars. Mining methods are of course, limited by the existing technology. Advancing technology, coupled with the limited production capabilities of open stoping, low efficiencies and high relative cost early in the history of the operation recommended that other mining methods be looked at. In Sweden, considerable practical experience, coupled with a large amount of theoretical work had become available on sublevel caving. To Pea Ridge it offered the apparent benefits of: 1) The flexibility of diesel powered trackless haulage. 2) The efficiency of two machines to one operator on longhole drilling. 3) A multilevel production picture with a large number of drawpoints for ore recovery. 4) 100% recovery of the mineable portion of the orebody in one production pass, with no pillar recovery problems left behind. This paper outlines the experiments and experiences which Pea Ridge has gone through with sublevel caving from 1967 to this date.

Jan 1, 1981

By B H. A Brown

The components of passive laser survey systems and their relative functions are presented. A general outline of the capabilities and the information available are followed by two case histories. These involve the use of such systems in quarry blasts where loading adjustments and drilling designs were required. Their application in blast casting operations, stockpile measurement, surface and underground construction, and general surveying areas are briefly covered, with comments on the potential for demonstrating a return on an investment in laser survey equipment.

Jan 1, 1990

By Shun Myung Shin, Dong Hyo Yang

Cobalt is recovered from square type of spent lithium ion batteries (LIBs) containing 5~20 % Co, 5~7 % Li, 5~10 % Ni, 15% organic chemicals, and 7% plastics together with Cu, Al, Fe, and Mn. The waste LIB was prepared by physical treatment. After screening, the crushed LIBs were separated to +8 mesh, -8/+16 mesh, and -16 mesh powder. Among these, -16 mesh powder was selected for leaching. The leaching test was investigated at 2 M H2SO4, 6 vol.% H2O2, reaction temperature 60 ?, agitation speed 300 rpm, solid/liquid ratio 50 g/ 500 ml, reaction time 1 h. The leaching efficiency of cobalt was more than 99 % and its concentration was 24.9 g/L. For removing of impurities such as copper, iron, and aluminum in the leaching solution before cobalt solvent extraction, the impurities were eliminated by pH control with alkali solution. For selective extraction of cobalt, the aqueous phase removed impurities was equilibrated with different volumes of 0.4 M Cyanex 272 saponified of 50 %. Extraction efficiency of cobalt was about 80 % at first step. Separation coefficient (ßCo/Li) of cobalt and lithium extractions was 206.5. Over 9.0 % of pure cobalt sulfate solution was obtained after stripping with H2SO4 solution.

Jan 1, 2008

By L. I. Gonzalez de Vallejo

SRC rockmass classification have been applied to 25 tunnels in Spain and Italy, for which it was found that much heavier supports than those estimated by the RMR index were required. SRC and RMR indices and other relevant geomechanical data were obtained during the site investigation and construction stages. Data corresponding to in situ stress measurements, analysis of tectonic structures, and instability problems arising during construction were used to asses the state of stress. The relationship between tunnel section convergence and the SRC and RMR indices was also analysed. Support measurements based on SRC and RMR classification were compared with those actually used during construction. These analyses indicate that for most of the tunnels examined, supports estimated using the SRC were much closer to those actually installed than those predicted by the RMR index. Bei der Verwendung des SRC-Systems zur Klassifizierung des Gesteins als Baugrund für 25 Tunnel in Spanien und Italien wurde festgestellt, dass viel schwerere Abstützungen benötigt wurden, als wenn die Beurteilung anhand des RMR-Systems angefertigt würde. Die Klassifizierung anhand des SRC- und des RMR-Systems, sowohl als auch andere wichtige geomechanische Daten wurden während des Ablaufs der Erkundungen und der Bauausführung gewonnen. Die Resultate der Messungen der Spannungen vor Ort, die Analyse der tektonischen Struktur und die Stabilitätsprobleme während der Bauausführung wurden dazu verwendet, um den im Felsgrund vorherrschenden Spannungszustand zu definieren. Das Verhältnis der Messungen der Tunnelkonvergenz zu dem SRC- und RMR-Index wurde auch analysiert. Die durch das SRC- und RMR-System vorhergesagte Grösse der Abstützung wurde mit der Grösse der Abstützungen verglichen, die am Bau letztlich verwandt wurden. Diese Vergleiche zeigen, dass für die meisten der studierten Tunnel die Vorhersage der Abstützungen, die anhand des SRC-Systems angefertigt wurden, viel näher der wirklich verwendeten waren als die Vorhersage anhand des RMR-Systems. SRC rockmass la classification ont été appliqué à 25 tunnels en Espagne et l'Italie, pour laquelle il a été trouvé que des appuis beaucoup plus lourds que ceux évalués par l'index RMR ont été exigés. SRC et des index RMR et d'autres données geomechanical appropriées ont été obtenu pendant l'enquête de site et les étapes(scènes) de construction. Les données correspondant aux mesures de stress(d'accent) in situ, l'analyse de structures tectoniques et des problèmes d'instabilité surgissant pendant la construction ont été utilisées aux ânes(culs) l'état de stress(d'accent). Le rapport entre la convergence de section de tunnel et le SRC et les index RMR a été aussi analysé. Les mesures d'appui basées sur SRC et la classification RMR ont été comparées avec ceux en réalité utilisés pendant la construction. Ces analyses indiquent que pour la plupart des tunnels examinés, les appuis évalués utilisant le SRC étaient beaucoup plus proches de ceux en réalité installés que ceux prévus par l'index RMR.

Jan 1, 2003

By K. Izumi

Ultra-grain refinement and high strengthening of metals by accumulative roll bonding (ARB) was widely reported. However, applications of ARB to magnesium alloys were rather limited. In this study, Mg-9%Li-1%Y sheets were applied to ARB at room temperature. Six 0.5 mm thick sheets were stacked and reduced into 0.5 mm thick by four passes. The procedure was repeated up to three cycles, so that the equivalent strain of 6.2 was applied. The sheets show dual phase structure with a (hcp) and ß (bcc). Grains elongates to the rolling direction with increasing number of ARB cycles. After three cycles, fragmented a grains with average size of about 300 nm are uniformly distributed. After the first cycle, the ultimate tensile strength increases to 180 MPa from 133 MPa, while the elongation decreases, however, still high (26%). The tensile strength slightly decreases by the second cycle and does not change at the third cycle. Meanwhile the elongation increases by the second cycle and the sheets show 41% of the elongation after the third cycle.

Jan 1, 2006

Over and above the technical support arid consulting work described in the preceding Parts of this Volume, ADL staff also provided a wide range of additional technical assistance to the Bureau on an ad hoc basis over the course of the contract, and particularly in 1973. Some of these assignments were on tasks that temporarily assumed a high priority at PMSRC, requiring a fast response, while others were more suited to conventional schedules but on communication and location topics less directly related to those in the preceding Parts. Chapter I briefly describes some of the diverse short-term assignments while Chapters I1through V treat assignments on the other topics. I SHORT-TEXM ASSIGNMENTS A sampling of short-term, fast-response assignments undertaken on mine communications and miner location for PMSRC during 1973 are given below. These assignments included technical reviews, discussions and recommendations related to the theory, experimental data, designs, and hardware implementation of experimental CW and pulse miner location EM transmitters; preparation of technical performance specifications for a miniaturized preproduction prototype CW electromagnetic location transmitter; review of specifications for a seismic signal detection experimental study; participation in technical discussions and experiments with PMSRC and equipment suppliers regarding the UHF radio/radiax-cable communications installation in the Bruceton mine; participation in an informal conference to discuss mine communication and monitoring needs and preferences with representatives of the Bureau, mine operators, and equipment manufacturers; participation in technical discussions with representatives of a U.S. mine operator and CERCHAR* concerning the characterization of faults on trolley lines and means of improving their rapid detection;** recommendation of simple signal, noise, and ground fault measurements on mine phone lines; review of an inexpensive automatic telephone dialer; preliminary discussions regarding the feasibility of adapting and assembling a collection of available telephone industry carrier equipment for installation and test in an operating coal mine; evaluation of a proposed call alert mine paging system; review of hardware designs and future experiments for a mine communication sled; design critique of a proposed six-channel narrow-band FM voice modem for carrier communication on the mine phone line; preparation of technical performance

Jan 1, 1974

By Jack Levin

Dr Laurence AlIison Bushel, a former President of the Chemical, Metallurgical and Mining Society of South Africa, now The South African Institute of Mining and Metallurgy, was born in Queenstown on 20th June, 1910, and died in Johannesburg on 4th November, 1991. There were three distinct periods in the career of Laurie Bushel, each enlivened by some special interests or achievements.

Jan 1, 1991

By S. Perkins, E. Young, L. Dufour, K. McVey, L. Rolandi

This paper presents a review of plant layout considerations incorporated into recent designs of SAG/Ball mill circuits for two medium sized concentrators. The plant layouts presented and the design concepts discussed, relate to smaller SAG circuits, but can equally apply to larger milling circuits. Included are design concepts and ideas introduced by the various project teams, and the focus is on the primary factors of any layout design which are safety, constructability, operability, and capital cost.

Jan 1, 2012

By Robert Morgan

With improved methods for designing and detonating shots the potential for flyrock can be significantly decreased, but there are few absolutes in blasting; therefore blasters must learn from the mistakes of others. Blasters must conscientiously employ control measures to minimize the risk of flyrock. The worst case incidents which tend to be widely reported by the media, should serve as a reminder to us all that minimizing the risk of flyrock must be incorporated into the design of the drill pattern and blast design.

Jan 1, 2001

By William B. Beerbower

When full length resin grouted bolts were introduced into U. S. coal mines some 11 years ago, it was assumed that safety would be the primary benefit. There is ample testimony to substantiate the safety factor as an important reason for using resin roof bolts. More recently, it has been determined that many coal operators not only concur with the safety consideration but also benefit economically from the safer working conditions resulting from a reduction in roof falls. IMPROVED SAFETY Some typical roof fall reduction experiences with resin bolting follow: ? Western Kentucky Mine - Resin bolting reduced roof falls by 80%. ? Southern West Virginia Mine - Experienced 141 roof falls between 1971 and 1972. In 1973 with resin bolting, roof falls were reduced 85%. ? Western Pennsylvania Mine - In 1973 had 59 roof falls with mechanical bolts. During the same period of 1974 with resin, only 19 falls were experienced - a reduction of 66%. The overall experience with resin bolted roof support has been an average 50% reduction in roof falls. Long term, this can translate into improved worker morale. As a matter of fact, a general mine foreman at the same Southern West Virginia mine mentioned above commented that improved miner morale was noticeable following the introduction of resin bolting. HOW GREATER SAFETY CAN BE COMBINED WITH INCREASED PRODUCTIVITY IN COAL MINING OPERATIONS Experience has also shown that a reduction of roof falls with resin bolting has resulted in increased production for many coal operators. Some typical examples with mines using resin bolting follow: ? Western Kentucky Mine - Resin bolting contributed to increasing production from 7000 to 11,000 tons per day, due to a 80% reduction in roof falls. This was accomplished in part by a reduction of 50% in timbering requirements and the reassignment of three roof fall cleanup crews to coal production. ? Pennsylvania Mine - Following resin bolting introduction the section showed a 50% increase in production. ? Central West Virginia Mine - Continuous miner production averaged 6 cuts per unit shift prior to resin bolting. Reduction of cleanup time, resulting from improved roof support with resin bolting, increased production to an average of 9 cuts per unit shift. PROPERTIES OF RESIN BOLTING SYSTEMS Several of the important properties of resin bolting systems which contribute to its improved performance are listed below: ? Full length anchored resin bolts and many resin anchored, point anchored bolts provide effective resistance to changing rock strata stresses throughout their length, thereby improving stabilization of rock strata over long periods of time. ? Individual layers of rock are anchored into a single high strength beam providing excellent resistance to vertical and lateral strata movement, the most common cause of roof failure. ? Moisture cannot corrode the fully grouted bolt. ? Has twice the pull strength of mechanical bolts (See Figure 1)

Jan 1, 1982

By Samuel P. Harteis, Eric S. Weiss

The National Mining Association and the Mine Safety and Health Administration requested that the National Institute for Occupational Safety and Health (NIOSH) conduct full-scale evaluations of a recently developed carbon fiber-reinforced polymer (CFRP) reinforcement technique for upgrading existing mine ventilation seals to withstand an explosion pressure of 50 psi or greater. The evaluation was conducted in the NIOSH Pittsburgh Research Laboratory’s Lake Lynn Experimental Mine (LLEM) near Fairchance, PA. The purpose of the evaluation was to determine the blast resistance of the CFRP reinforcement technique, designed to increase the strength of two types of existing 20-psi-rated in situ mine ventilation seals. Two candidate ventilation seals were selected to represent the 20-psi alternative seal designs typical of those used in mines prior to July 2006. Installed within the LLEM were (1) a 4-ft-thick pumpable cementitious foam seal using material with a designed 150- to 200-psi average compressive strength at 28 days and (2) a 24-in-thick, low-density cementitious block seal with a center pilaster and keyed to the floor and ribs. The materials necessary for the CFRP reinforcement technique were then installed on the outby (active) side of each seal, and the seals were subjected to explosion overpressures. Both seals with the CFRP reinforcement retrofit successfully withstood explosion pressures of 60 psi or greater during the full-scale evaluations in the LLEM.

Jan 1, 2008

By J. Richard Kyle

On page 1617, the author's box was incorrect. It should have read: J. R. Kyle, member SME, is an assistant professor of geology. Dept. of Geological Sciences, The University of Texas at Austin. Austin, TX. On page 1616, the italic line 22, beginning "Murray, R.C. ... " should have been deleted. On the same page, the first two lines (27 and 28) referring to Norris, A.W., 1965 . . . should have been deleted. Column 2 should have preceded column 1.

Jan 1, 1981

By Freeman Bishop

The Bureau of Mines is working on a long-term program to completely revolutionize mining-to create a mine-systems technology that integrates the need to recover minerals at low cost under safe and healthful working conditions while protecting the environment. Everyone should be brought into the planning process preceding each new mining development, the Interior Department urges, and Assistant Secretary Hollis M. Dole seems determined to push this kind of systems approach with everything he can move.

Jan 1, 1970

By Dorothy A. Canter

Three Federal programs exist for identifying significant environmental chemicals, including minerals, that should be tested for toxicological effects. Two programs are mandated by law and can lead to industry-funded studies; they are administered by the Environmental Protection Agency and the Agency for Toxic Substances and Disease Registry, respectively. The third is the National Toxicology Program, a Federally-funded testing initiative. This paper summarizes the three programs, describes their similarities and differences, and discusses their applicability to minerals.

Jan 1, 1991

This work describes preliminary laboratory testwork to study the relative leaching response to cyanidation and thiourea leaching of an oxidised low grade gold ore. The potential of an alternative lixiviant like thiourea to commercial processing of mine dumps is discussed by specific reference to selected case histories. It would appear that on the basis of the available published information, there could well be a case advanced for the acid thiourea leaching of sulphide concentrate tailings being subjected

Jan 1, 1994

By S. Jiansheng, H. Nakayama, D. Lu, A. Wang

ABSTRACT: New techniques and methods for 3D geo-mechanical model test are presented in this paper. The new model material NIOS with high density and low cost; the so-called DPSS (Discrete Principal Stress Surface) loading concept, the loading and monitoring system for the generation of the 3D initial stress field of the model test, also the special techniques and apparatuses for modelling the excavation of caverns located deep inside the model material, are developed and introduced. By adopting those new techniques, a very large 3D geo-mechanical model test with high comparability for a newly designed underground powerhouse has been successfully fulfilled. Key Words: 3D model test, underground group caverns, excavation process modeling. ZUSAMMENFASSUNG: Neue Techniken und Methoden für 3D geomechanischen Modellversuch wurden in diesem Artikel vorgestellt. Ein neues Modellmaterial mit hocher Dichte und niedrigem Preis, ein sogenanntes DPSS (Discrete principal stress surface) Ladenkonzept, ein Laden- und Überwachungssystem für die Erzeugung des 3D primären Spannungsfelds und überdies spezielle Techniken und Maschinen für das Ausbruch der tief in dem Versuchsmodell liegenden Kaverne wurden entwickelt. Bei Anwendungen dieser neuen entwickelten Techniken wurde ein sehr großer 3D Modellversuch mit großem Maßstab für ein geplantes unterirdisches Kraftwerk erfolgreich durchgeführt. Stichworte: 3D Modellversuch, unterirdischen Gruppekaverne, Ausbruchsmodellierung Résumé: le test de modèl de Nouvelles techniques et méthodes pour la géo-mécanique 3D est figuré dans ce papier. Le nouveau modèle de matériels NIOS avec la haute densité et le coût bas; la conception proposée de chargement DPSS (Discrete Principal Stress Surface), le système de chargement et de moniteur pour la génération de champs de stress initial du test de modèle, ainsi que les techniques et appareils spéciaux pour modeler les excavations de cavernes profondément localisées dans l’intérieur du matériel de modèle, sont développés et introduits. A travers l’adoptation de ces nouveaux techniques, le test de modèle de la géo-mécanique très large 3D avec la haute comparabilité pour actualiser une nouvelle étude de la centrale électrique sous-terraine a déjà accompli avec succès. Mots de clé: test de modèle 3D, groupes de cavernes sous-terraines, processus de modèle d’excavation

Jan 1, 2003