Search Documents

By Nathan W. Iverson, David S. Graham, Paul J. Axtell

"The Highway 53 relocation project in Virginia, Minnesota, involves construction of a very tall bridge across a currently inactive iron ore mine pit. The inactive pit is partially flooded and serves as the community’s drinking water source. The 1,132-ft long new bridge is a three-span, plate girder structure. Two intermediate, approximately 200-ft tall piers are located within the pit.The foundations for the two piers consist of groups of 30-in diameter piles which, despite the contradiction in terms, are essentially very large micropiles. Extremely challenging and highly variable subsurface conditions exist at the site, ranging from uncontrolled iron ore mine waste fill to some of the hardest rock on earth that can also be highly fractured and abrasive. Despite the conditions, large diameter (30-in) micropile foundations up to 175 ft deep were successfully installed using down-the-hole hammer methods and full-length permanent casing under an extremely aggressive construction schedule.Full-scale foundation load testing using the Statnamic rapid loading method was also conducted in support of the design and construction but under a separate pre-design phase contract. This paper describes the unique aspects of this foundation project, including design, construction, and load testing of the large micropiles.INTRODUCTION AND BACKGROUNDIn 1960, a segment of Trunk Highway 53 (TH-53) in Virginia, Minnesota, was built on land owned by iron ore mining interests. As part of the roadway easement agreement, Minnesota Department of Transportation (MnDOT) was to be given notice three years prior to termination of the easement. In 2010, MnDOT received notice that the mining interests wished to access the ore. Through negotiations in 2010, MnDOT and the mining interests agreed to a 2017 date for abandoning the existing section of roadway. During this period, MnDOT needed to procure project funding, satisfy environmental permitting requirements, and acquire new right-of-way to permanently reroute TH-53 and keep it open to traffic. This was no easy task due to the existing mine pits surrounding the area.The E-2 alignment option shown in Fig. 1 was ultimately selected for the rerouted highway in 2014. The new highway segment includes a three-span bridge across the currently inactive Rouchleau Mine Pit. The inactive pit is partially flooded and serves as Virginia’s drinking water source. The 1,132- ft long new bridge is a three-span, plate girder bridge. Two intermediate approximately 200-ft tall piers are located within the pit. Fig. 2 is a conceptual rendering of the bridge."

Jan 1, 2017

By K. E. Barnes

"The “Jameson Cell” flotation cell was developed at Mount Isa Mines in the late 1980’s to address deficiencies in our flotation column installations. Early base metal installations had a variable record. The test work and trials showed they made an improvement metallurgically when operated correctly, but performance of the early installations was hindered by a range of operational and maintenance issues. The installations needed to be more robust, and we needed a better understanding of how to successfully integrate the cells into the plant flow sheet.During the 1990’s, Jameson Cells had great success in coal fines flotation and organic removal in SXEW applications, and became the standard in these applications in Australia. These installations improved the cell design and materials of construction and the cell flow sheet design, to make it low wear with self-regulating control, producing good performance with little operator input.These improvements have enabled a fresh look at the use of Jameson Cells in base metals. Recent new installations have shown significant benefits in “hybrid” circuits, that combine the best features of both Jameson Cells and conventional flotation cells, achieving better overall circuit performance in a smaller footprint than either technology could do by itself.Case studies of successful base metal applications are discussed, using size-by-size mineralogical performance to explain the improved circuit performance. The new methods of flow sheet test work design are also described."

Jan 1, 2006

By L. R. Plitt

A new simple correlation has been developed to evaluate the performance of classifiers. The new correlation has been tested on existing data from 150 different hydro-cyclone classification tests. It is shown that this model provides a meaningful improved method of mathematically describing the classification process.

Jan 1, 1971

Minerals processing operations use a significant quantity of fossil carbon to provide energy and as reductant. Greenhouse gas emissions from the use of this fossil carbon contribute to the global increase in anthropogenic CO2 emissions to the atmosphere. In the spirit of fostering thinking about a step change in this situation, this paper explores opportunities for the use of sustainable carbon from biomass sources in a range of mineral processing operations. The exploration shows that many common processes are contenders for fossil carbon replacement and that feasible scientific research by minerals processing technologists would add to deeper understanding of the potential for a sustainable bio-carbon based industry. It is also shown that there are many dilemmas on the social, environmental and economic fronts to be solved before a biomass based industry could become a reality.

Jan 1, 2004

By Y. H. Liu

Several foaming aluminum samples of different density were prepared in a semi-industrial scale experimental system. Their properties such as the energy absorption characteristics, mechanical properties, heat conductivity and acoustical properties were measured. The results showed that the foaming aluminum with a density of 0.5 to 0.6 g/cm3 has the best energy absorption and this makes it suitable as the ensuring bar of the automobiles and also as a cushion material for the engine. The foaming aluminum with a density of 0.25 to 0.4 g/cm3 has the best acoustical properties and heat conductivity resistance, which is suitable for the door filling material, the ceiling and the partition of the car engine.

Jan 1, 2003

By J. P. BONARDI, William F. Boericke

BOULDER COUNTY, Colorado, ranked during the war years and until the end of 1918 as one of the foremost tungsten-producing districts of the world. In 1919 production fell off drastically, due to heavy importations of foreign ores from China, Burma and South America. So large were the imports that even after the enactment of a protective tariff in 1922 of 45c. per lb. on tungsten metal, equivalent to $7.14 per unit (201b.) of tungstic acid? (WO,), the stocks of metal in this country were extensive enough to supply the demands of industry, and prevent general resumption of mining by domestic producers. Even today there are only two producers in the Boulder district though at one time as many as twenty separate companies were in operation. About the same ratio holds for other tungsten-producing districts in the country, including California and Nevada. Total consumption of tungsten concentrate in terms of 60 per cent WO2 in the United States amounted to approximately 3790 tons in 1928, according to Frank L. Hess.' Of this amount, domestic mines contributed 1290 tons, and the rest, 2500 tons, was imported. Yet in 1917, with tungsten concentrate selling at $20 per unit, the Boulder district alone produced 2707 tons, indicating the effect of enhanced ore price upon production. It is believed by American tungsten miners that, given a sufficiently high tariff, all the demands of industry can be met by domestic production without placing a prohibitive burden on consumers. For instance, in steel manufacturing the percentage of tungsten entering into the manufacture is so small that, ?regardless of cost, it can constitute but a small fraction of the cost of steel to the buyer.

Jan 1, 1929

By G. A. Irdi

An automated method of microscopy for determining the pyrite size distribution on two base coals that were crushed to 28 mesh x 0 has been developed. Polished epoxy-bound coal pellets were prepared and examined by a Zeiss IBAS image analyzer utilizing a program developed from provided software. Pyrite size distribution determination is considered a necessary first step in pyrite characterization that could lead to successful predictions, by microscopy, of a coal's theoretical pyritic sulfur removal. Our research efforts to date have indicated that the IBP-S can be a reliable instrument for determining pyrite size distribution in crushed coal. A program was also developed to convert pyrite size data to a weight basis for comparisons to the results from chemical analyses. The problems encountered in our research and their solutions will be presented in the discussion.

Jan 1, 1986

This paper deals mainly with the modernization in the coal loading system at the loading piers of the Dominion Coal Company, Ltd., Sydney, Nova Scotia. The history of the operation is briefly outlined, and the construction of the Company's new pier is described in considerable de-tail. Particular attention is paid to the bins and conveyors, and to the loading tower. The paper concludes with a description of the S.S. Cape Breton Miner, built specifically for the coal trade, and the unloading facilities at Lakeview, Ontario. Coal Shipping at Sydney C OAL from the mines operated in Cape Breton by the Dominion Coal Company, Limited, has been shipped from the International Piers, situated on the east side of Sydney Harbour, for over sixty years. There were three piers, of which two were active-ly used in the shipping of coal until 1964. Nos. 2 and 3 were high piers about 600 feet long, of wooden construction throughout. They were founded on' rock-filled cribs and creosoted piles driven into the harbour bottom, and each had two decks which carried standard-gauge railway tracks.

Jan 1, 1965

By G M. Tranell, M Tangstad

The CO2 footprints in the production of Mn-ferroalloys and silicon/ferrosilicon are correlated with the fossil carbon consumption. The CO2 emissions may be reduced in the Mn-ferroalloy process by increasing the degree of prereduction and reduction of carbonate materials, while the silicon/ferrosilicon process is optimised based on silicon yield. By changing the fossil reductant into biogenic reductants, the global warming potential will be decreased even more. Even if the reductants are biogenic reductants, there will still be a global warming potential (GWP) in eg the electrode consumption and the CH4 emissions in the charcoal production. To reduce the use of fossil reductants there are also more disruptive technologies like the use of H2 that at least for the silicon production is on a very low technology readiness level (TRL). Using metallothermic processes will reduce the use of carbon but requires carbon neutral metal reductants. Electrowinning can have low CO2 emissions, and the electrowinning of pure Mn is a technology of high TRL. Salt and oxide electrolysis is under investigation for both Mn and Si production however the research is still on a low TRL. The use of CCS/CCU (carbon capture storage/utilisation) is a part of obtaining carbon neutral processes. Last, the energy mix used for these energy demanding processes is discussed.

Aug 21, 2024

By J. H. East

"INTRODUCTION .Very little information regarding coal mining in Spain has been published in the American technical press, and few people realize the extent of this industry or the conditions under which coal is mined. The information in this publication was collected in 1945 and consists of personal observations in Spain, statistics, and other data of a, general nature obtained from official sources.Spain produces bituminous coal, lignite and anthracite, but the total tonnage mined is less than the national requirements. Before the war, an appreciable tonnages coal was imported from Great Britain under the Anglo-Spanish treaty, which rebated import duties and effectually prevented competition from any other foreign source. The war stopped the major part of the important of British coal and caused rapid expansion of the domestic sources, but this was not sufficient to supply the industrial demand. Coal that formerly was not acceptable to industry because of quality is now mined and marketed. The Government, allocates the better-grade bituininous coal to the various industries in accordance with the national importance of the work in which they are engaged; for example, the railroads are allotted 100 percent of their requirements, but cement companies can obtain only 25 percent.The Government offered to inducements to increase the production of coal of any class, but the larger part of the increased tonnage obtained was in inferior grades; as a result, the lignite production was taxed, while a bonus was paid for bituminous-coal production in excess of the 1942 tonnage.The anthracite and bituminous-coal areas were severely damaged during the Civil War and many experienced miners migrated to the lignite mines in eastern Spain. This has resulted in an acute shortage, particularly the Province of Oviedo where the most important bituminous-coal deposits are located."

Jan 1, 1947

By J. B. McKay

It is the purpose of this paper to present an initial report on the construction and operation of the Fluo-Solid roaster at the property of Campbell Red Lake Mines, Ltd., Balmertown, Ontario. The roaster prepares for subsequent cyanidation the bulk flotation concentrate obtained from four hundred tons per day of gold ore. The mill flow-sheet 'includes jigging and amalgamation; flotation; cyanidation of flotation tailing; and roasting followed by cyanidaition of flotation concentrate plus amalgamation tailing. Overall mill recovery for the year 1950 was 90.2 per cent. Recovery possible by straight cyanidation of this ore would not exceed 80 per cent. The ore contains considerable arsenopyrite and pyrrhotite as well as pyrite, with lesser quantities of nickel, zinc, and copper minerals. The mineralization is for the most part extremely fine. The roaster first went into operation on August 7th, 1949, and at the end of 1950 it had roasted 10,916 tons of concentrate. The average recovery of gold from calcine during that period was 94.86 per cent in the primary stage of calcine cyanidation. The average assay of calcine residue from primary cyanidation for the entire period was 0.37 oz. per ton. Both laboratory tests and plant metallurgical balance calculations indicate a further recovery of approximately 10 per cent of this 0.37 oz. when the calcine residue is again cyanided, in the flotation tailing cyanidation circuit.

Jan 1, 1951

By William J., Coulter

IN the early days of Colorado mining, between 1880 and 1900, when Leadville, Kokomo, and Robinson were boom mining camps, the entire area around Climax for a matter of fifteen miles was overrun with prospectors, so the mineralized outcrop at Climax was not unknown. The principal interest in minerals during this period was in gold, silver, and lead, and since the Climax outcrop showed none of these it drew little attention. Geology played an important part in bringing prospectors to the very edge of the Climax deposit. The Mosquito fault, which crosses near the base of Bartlett Mountain, continues as an important geological structure, at least as far as Leadville some twelve miles distant, and at the base of Bartlett Mountain the vertical throw on the fault is estimated to be between 2000 and 5000 ft. The sedimentary beds known to the Leadville district are all present on Bartlett Mountain to the north of the Mosquito fault, which cuts them off abruptly, and exposes the Pre-Cambrian rocks that underlaid them, so the prospectors, who were searching for gold, silver, and lead in the sediments

Jan 1, 1946

By Shuie Li, Taibai Li, Tao Hu, Zhongjie Wang, Xiang Ge

As one of the main power sources, lithium-ion batteries (LIBs) will continue to be applied on a large scale in the future market. Commercialized LIBs cathode materials contain various valuable metal elements including Li, Co, and Ni. The development of green and efficient recycling technology is essential. Deep eutectic solvents (DESs) have recently emerged as a new class of green solvents that could potentially be applied for the LIBs recycling industry due to their capability to leach the active materials without the introduction of environmentally hazardous reagents as used in conventional hydrometallurgy process. Considering the rapid progress, a critical review focusing on the progress and fundamentals about the overall efficiency has practical significance for the further advancement of this field. Herein, we briefly introduce the overall process of using DESs for LIBs recycling and specifically focus on the efficiency of each step. Current fundamental understandings and new experimental approaches to enhance the efficiency of the leaching process, the extraction process, and reusability are summarized. We expect this review article to inspire scientists to use DESs as powerful tools for advancing the frontiers of LIBs recycling.

Jul 30, 2022

By K. E. Stanfield

This report presents the results of analytical studies made on two series of oil-shale samples from the Mahogany ledge of the Green River mine the character of the various grades of oil shale that are being mined and processed into shale oil and refined products at the Bureau of Mines Oil-Shale Demonstration Plant at Rifle, Colo. The analytical work was part of a synthetic liquid fuels program being conducted at the Petroleum and Oil-Shale Experiment Station, Laramie, Wyo. The 16 oil shales ranG6d in color from a gray brown ( or a sample that assayed 10.5 gallons of oil per ton to a very dark brown for a sample that assayed 75.0 gallons of oil per ton. In general, the samples were similar as to the types of organic and inorganic matter that they contained but varied widely in the amounts or these constituents. The principal constituents were calcite, dolomite, illite, and yellow organic material, while the minor constituents were quartz, feldspar and plagioclase feldspar, pyrite, marcasite, analcite, opal, black organic material, and small woody fragments. Some micro-fossils, spores and pollen grains were found also.

Jan 1, 1951

By J. L. Fitch, B. G. Hurd

The presence of gypsum in samples subjected to standard core analysis introduces serious errors in the measurement of water saturation and porosity. The magnitude of these errors, depending upon the type of analysis procedure used, has been evaluated experimentally and theoretically. Water-saturated pore volumes determined by vacuum distillation or retort procedures may be too high by as much as 48 per cent of the volume of gypsum present. The maximum error in this value determined by Dean-Stark extraction with toluene is 36 per cent of the gypsum volume. If pore space is measured by a Boyle's law type porosimeter the maximum erorr due to gypsum is 38 per cent of the original gypsum volume present. The conscientious core analyst may eliminate the errors caused by gypsum by either of two methods. He may apply suitable corrections for the water of crystallization removed from gypsum, or take special precautions to prevent dehydration of gypsum during core cleaning and alzalysis procedures. These alternatives are discussed and methods for obtaining reliable core analysis data are proposed. Gypsum (CaSO4 . 2H2O) occurs as a common mineral in many of the world's sedimentary basins. In addition to its presence as primary bedded evaporitic deposits, it is often found as secondary replacement zones and pore-fillings in host rocks. That it may cause false indications in porosity, both on neutron logs and in standard core analysis, has been generally recognized. False porosity interpretations from neutron logs result because the chemically bound water in gypsum attenuates neutrons as effectively as free water. Errors in core analysis result when gypsum is dehydrated prior to or during the analysis. Vacuum retort procedures used by many laboratories to determine fluid saturation and porosity effect a complete removal of water of crystallization from gypsum. The crystal water, distilled and collected with free water from the sample, is counted as water-sat11rated pore space. Dehydration of gypsum results in a decrease in volume occupied by calcium sulfate and a corresponding increase in pore volume. Thus, if gypsum is dehydrated by sample cleaning and drying procedures, subsequent porosity measurements with gas expansion or compression instruments will be high. The qualitative effect of gypsum on porosity determinations by retort procedures was discussed in a recent article by Bynum and Koepl3. They concluded that since false porosity was interpreted as being water saturated, determinations of oil content were not affected. Others in the industry, however, have pointed out that porosity values are often used with values of water saturation determined independently, e.g., from electric resistivity logs in making reserve estimates. Values of water saturation calculated from the formation resistivity using the Archie equation, S4= are actually low if values of are high due to gypsum. In this case, false porosity values due to gypsum could cause serious errors in calculations of oil-in-place. This investigation was made to determine quantitatively the effect of gypsum on porosity values determined by different core analysis procedures. EXPERIMENTAL PROCEDURES Dehydration of Gypsum The extent and rate of removal of water of crystallization from gypsum under conditions encountered in core analysis procedures were studied. Taken for the experiments were three types of relatively pure, naturally occurring gypsum, viz. selenite, satin spar and massive gypsum. Although all samples probably contained trace chemical impurities, each type lost the theoretical amount of water upon complete dehydration. An automatic recording thermobalance, similar to one described by Mauer2, was used to obtain dehydration rate data for samples heated in dry air. Water

By Clarence A. Wright, JAMES T. NORTON, JAMES G. PARMELEE

The object of this paper is to give to mining companies and to all others who are interested some idea of the possibilities in the treatment, by differential flotation, of lead-zinc ores of the Coeur d'Alene region and other districts. The purpose of these investiga.. tions is not to evolve a differential flotation process that would replace present methods of gravity concentration but rather one that could be applied to the relatively fine material and slime produced in the mills and treated unsuc_pessfully by gravity methods or by flotation. It is expected, of course, that the products to be obtained by differential flotation would be of much better grade than those now produced by flotation in the Coeur d'Alene mills. In view of the fact that it has been difficult to obtain representative samples of flotation feed from the mills, owing to the necessity of shipping the material wet and free from oil or other foreign matter that might be deleterious to the differential separation of the sulphides, the writers have felt justified in running flotation tests with the mill feeds in order to ascertain whether a differential separation of the sulphides could be effected. However, two different lots of flotation feed were tested for differential flotation, and the results of tests of one of these are given in this report. It is hoped that it will be possible later to test out the flotation feed for differential flotation on a large scale in some of the mills. This paper covers part of the investigations carried on by the United States Bureau of Mines in cooperation with the Idaho Bureau of Mines, the University of Idaho, and certain mining companies of the Coeur d'Alene region. Although the results of the tests included in this report are not to be considered final, they indicate possibilities and may suggest others leading to a solution of the problem of separating lead and zinc sulphides by differential flotation in the treatment of certain ores.

Jan 1, 1921

By John M. Gordon

DURING and after 1949, various groups of British mining engineers came to the Dominion Coal Company, Limited, at Sydney, N .S., to see at first hand the Dosco MINER ( 1). These visits culminated in 1952 with the ordering of four Dosco Miners by the (British) National Coal Board on an experimental basis through their Experimental Expenditure Funds. Others are now on order. The first machine was delivered in February, 1953, and, after slight alterations to suit the different power supply, the machine was made ready to work. Due mainly to the size of the machine, new rules and regulations governing its operation had to be put into effect and it was not until April, 1954, that the machine was put underground. It started to produce in June of that year. The three others were delivered early in 1955. The authors were sent to England by the Dominion Coal Company to install and demonstrate these machines and to work with the Coal Board engineers to- further interest in the machines in the British coal fields .

Jan 1, 1956

By F. F. Sharpless

ARRIVING at Davis Junction, after leaving Portland, we expected to wait for an hour and a half, but found the superintendent of motive power of the Southern Pacific, Mr. Williams, waiting for us with a car, and were immediately taken aboard this and whisked off to Sacramento. After dinner, we were taken to the railroad shops to see their work in reclaiming scrap steel. We saw them draw off the slag from the electric furnace, and later make a casting. At about 11 o'clock, we took the train for Reno. A delegation of the Nevada Section, with Mr. Kirchen and Mr. Rives at its head, met us at the station. Immediately after breakfast, we started for the property of the Comstock Mines Co., where General Bulkeley Wells was to be our host. We had a de-lightful ride out to the mines and through the old city of Virginia, or through what was left of that old city, reaching General Wells' camp at about 10:30. This contains the newest thing in cyanidation and a remarkably fine iron and concrete mill building. After a trip underground, we were called to luncheon, where about 250 sat down. The afternoon was spent in the mill, and we were taken to Gold Hill, which is a part of Virginia City, for dinner, again as the guests of General Wells, who made a consummate toastmaster. Governor Emmet Boyle was the first speaker; he was followed by President Dwight, and then came President William Sproule of the Southern Pacific. A song, "The Engineer," was followed by Senator Key Pittman, Professor Jones of the State University, Mayor Stuart of Reno, and ex-Senator Charles Hend-erson. The president of the Western Pacific and the president of the Pacific Coast Line were there, also many notable operators of Nevada and California.

Jan 11, 1922

By P T. Stoker, A Allman, D P. Carville

Classification of mineral resource estimates is one of the most important responsibilities of the Competent Person. In recent years, classification decisions have been driven more by the detailed block-by-block attributes generated by the now widely applied geostatistical estimation methods, and less by a general geological overview. This is increasingly resulting in æspotted dogÆ outputs, in which blocks of Inferred Resources or unclassified material separate blocks of Measured and/or Indicated Resources, or individual drill holes are surrounded by annuli of Measured and Indicated Resource blocks. Not only are such outputs potentially misleading, since they ignore fundamentals such as continuity of geology and mineralisation between drill holes and the imprecise nature of resource estimation, they can also cause substantial problems for engineers undertaking mine designs and estimating ore reserves, particularly for underground mines. Competent Persons for mineral resources must keep in mind the purpose of their work, and should use their experience and judgement to avoid or smooth out æspotted dogÆ classifications, providing a result commensurate with the level of geological and resource estimation confidence. For their part, ore reserve Competent Persons must understand the resource estimation and classification process, and should question resource classifications that are not consistent with the level of geological and resource estimation confidence.

Jan 1, 2006

By John S. Anderson

The need for fuels and minerals in this country is estimated to double, triple, or even quadruple by the end of the present century. Even assuming more recycling of scrap metals and some priority allocation of energy, as has been done, for instance in war time, the projected increase in the nation's population and ever-increasing wants of that population will require vastly more minerals than are now being produced. Since mineral ores are being mined at lower grades, and since all minerals, including fuels, are having to be mined from deeper deposits, the amount of surface land to be disturbed will, inevitably, be increased. We cannot depend on foreign sources to supply all the extra requirements, since the non-U.S. population is increasing, in most cases, faster than our own. Furthermore, starting from a lower base, their mineral needs may accelerate more rapidly than ours. Restrictions on exports may be applied in foreign countries, if it appears that remaining reserves are not sufficient to fill the national needs. In vice; of the opposition which the mineral industry is receiving, as has been well described at these sessions and elsewhere, what can we, as mineral producers, anticipate as regards our ability to continue to operate, to sway nothing of expanding production? Although not minimizing the problems involved, it seems obvious that, except under emergency conditions, the country cannot tolerate a reduction in the available

Jan 1, 1971