Search Documents

By J. P. Caulfield

THE Hudson Bay Mining and Smelting Company's underground mine at Flin Flon, Manitoba, has in the past been serviced by two working shafts-the North Main shaft, and the No. 3 shaft. The North Main shaft is used to hoist the total production from under-ground, and handles the greater part of the mine supplies and crews. The shaft is five-compartment design, rectangular in cross-section, and is equipped entirely with steel shaft sets from the surface to the finished depth of 2,210 feet. Hoisting equipment in the surface plant will not permit the North Main shaft to be extended below its present finished depth. The No. 3 shaft, located approximately 2,300 feet from the North Main shaft, is used primarily as a ventilation shaft, and for hoisting lower-level development waste to the 390 level, where this material is used as mine fill. The No. 3 shaft is of standard rectangular design, timbered with 8-in. by 8-in. creosoted fir sets, hung on 6-foot centres. From the surface to the 1,430 level, the No. 3 shaft consists of three 5 ft. by 5 ft. compartments, and below this level to the completed depth of 2,300 feet, the shaft is increased to four compartments. To service the mine and to expedite development below the 2,210 level, a one and one-half compartment winze was sunk from the 2,210 level to a depth of 766 feet, or approxima tel y the 3,000 level.

Jan 1, 1941

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining I research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and, the results are described in this report.

Jan 1, 1983

By David C. Lynch

FeCl3 particulate of 10 to 100 um in diameter was reacted with radicals produced in an oxygen plasma at pressures between 1 to 20 Torr. The particulate, in a fluidized bed, was positioned above the plasma to avoid over heating the oxide product which is known to lead to crust and clinker formation[ 1 ]. Reaction between the iron chloride and the gas phase occurred at temperatures between 66 and 226 °C. Oxygen radicals react with the surface material to a depth of approximately 2.5 4m. Surface material, analyzed with a x-ray technique, indicates that the maximum amount of FeCl3 reacted on a weight basis was found to be approximately 67%. More typically, 40 to 50 wt% of the chloride was reacted within 30 minutes to 1 hour.

Jan 1, 1996

By W. William Culver

James Douglas became known in the nineteenth century for two reasons fundamental to his mining career: (1) his experimental work with copper hydrometallurgy, and (2) his grasp of the idea that the quantity of copper ore matters more than the quality. On the first reason, there is a moment for any technology that’s critically important—when it moves from an area of scientific interest to one that companies are founded on. This paper examines the original 1869 Hunt and Douglas Copper Process in the context of science and engineering as they were in the 1860 and 1870s. It was a “humid” process, developed at Quebec’s Harvey Hill Mine. Chemically, the Hunt and Douglas vat leaching process succeeded, but not the original companies using it. On Douglas’ understanding of ore quality versus quantity, luck had it that the first company to field test the Hunt and Douglas Copper Process was in Chile. The Hunt and Douglas patent made that transition from experimental model to operational plant in 1870 when the Compañia de Minas de la Invernada was organized in Valparaíso. As a joint-stock company, Invernada spread the risk of investing in the revolutionary, but untested, Hunt and Douglas Process. The company brought Douglas to Chile as a consultant in 1871. His experience with hydrometallurgy, combined with what he learned about the copper business while in Chile, set him off on a career in metal mining that both surprised Douglas and made him wealthy.

By David Porter, Nathan Rouse

The implementation of presplit perimeter control in underground mining as a method to decrease dilution yields positive benefits throughout the current and future mining cycles. A case study to understand the benefits of reducing overbreak and underbreak in a cut and fill mining cycle was performed to quantify the reduction in backbreak. The study was performed in a control section of the mine where a presplit perimeter control design was utilized for a length of heading. This control heading was then compared to the existing standard blasting design within the same mining zone. The comparison included multiple aspects of the mining advance including overbreak, dilution of waste, dilution of Cemented Rock Fill, bolt counts, and cycle times. Once mining in the control section was completed and mining commenced in adjacent headings, blast damage due to blast design could be quantified.

Feb 6, 2023

By W. H. Ryback

When a fire or explosion occurs in an underground coal mine, the atmosphere guickly becomes irrespirable. Highly irritant smoke and toxic levels of carbon monoxide and dioxide are produced, and consumption of oxygen by the fire or blast can reduce its concentration below that needed to support life. Work parties entering such a hazardous atmosphere for rescue or recovery operations are required to use, as their primary respiratory protection, a fully self-contained breathing apparatus of at least two hours duration. Apparatus used in this role has primarily been of the closed circuit rebreather type, using pressurized oxygen storage and chemical removal of expired carbon dioxide. Typically, commercial self-contained breathing devices for mine rescue have been heavy, bulky, and uncomfortable to use. The McCaa apparatus, long the industry standard, represented the best art available when it was First designed in 1926. It weighs 41 Ibs., protrudes about six inches above shoulder height, and provides breathing gas at temperatures up to 120° F. More recent designs, such as the Drager BG174A and Scott Rescue-Pak, using modern light weight materials and fabrication techniques have improved on all parameters of the McCaa to some extent. It was the intent of the Bureau of Mines, acting under the authority of the Coal Mine Health and Safety Act of 1969, to fund the development of a new self-contained breathing apparatus which would incorporate the best available technology and serve as a benchmark for future commercial designs, as the Bureau-sponsored McCaa had 45 years previously.

Jan 1, 1974

By G. S. Beaumont

This report presents a programme of work to demonstrate the use of a surface-based centralised computer control system for the remote monitoring and control of underground conveyors in a US coal mine. The system selected for demonstration was the 'Dynalink' Micro MINOS system which is manufactured by Hawker Siddeley Dynamics Engineering Limited. The site selected was Barnes S Tucker Lancashire No. 20 Mine located near Carrolltown, Cambria County, Pennsylvania. The system concept, operating and application software was designed and developed by the. British National Coal Board. The report describes the selection of the site, specification of the system requirements, commissioning, operation and evaluation of the system under typical US mine operating conditions. Experience with the system, based primarily on the system reliability and performance of conveyor control, was favourable. Mine management personnel felt that the system had successfully achieved its objectives and were keen to expand monitoring and control to other activities.

Jan 1, 1986

By Anastasia Xenaki, Edmundo Laporte, Antonio Nieto, Jesus Castillo Gomez, Oscar Velasquez

It is particularly challenging for the mining industry to create and implement an efficient and adaptable mining innovation model to secure the continuous improvement of processes and products via technology. Human resource departments must play a vital role in shifting the mining culture, enabling these new classes of digitally skilled professionals to manage the mining operations of the future. This paper proposes the implementation of a concept based on the 5S mining innovation model ((a) Nieto, 2019), in a coal mining project in Central Asia, Mongolia. Practical and empirical evidence suggests that the model could serve as a roadmap to developing technologies and methods for the mines of the future.

Feb 1, 2023

By R. H. Fernald, C. D. Smith

When the United States Geological Survey began operations at the coal-testing plant erected at the Louisiana Purchase Exposition at St. Louis, Mo., in 1904, it had already outlined a comprehensive plan for the systematic study of coals, lignites, and other mineral fuels with reference to their suitability for particular purposes and the methods by which they could be utilized most efficiently. Recognizing the need of information on the relative economy of producer gas as compared with steam for power purposes and the lack of comparable tests of American coals in the gas producer, the Geological Survey undertook investigations of the merits of different coals as producer fuel for the purpose of promoting efficiency in the utilization of the nation's fuel supplies. These investigations were carried on at St. Louis, Mo., and, later, at Norfolk, Va., and Pittsburg, Pa. The aet of Congress approved May 16, 1910, transferred the fueltesting work being carried on by the Geological Survey to the Bureau of Mines. This bureau is conducting producer-gas tests at P~ttsburg, Pa., and is publishing and distributing reports relating to all the fuel tests made by the Survey. These investigations into the possibility of generating producer gas in a commercial way for power purposes from the various fuels of the country have been associated with steaming, briquetting, coking, and other tests, all of which supplemented an examination into the nature, extent, and distribution of the fuels. The tests have all been made with carefully selected representative samples and carload lots of materials procured specially for the purpose by experienced collectors.

Jan 1, 1911

By M P. Murphy, C M. D Barton

When developing a new underground mine, the geological interpretation that guides the mineral resource is crucial to the preparation of a reliable ore reserve. In preparing a robust geological model to underpin a resource estimate, practitioners must weigh the comparative risk of accepting a relatively wide-spaced drill hole pattern, versus a more close-spaced pattern that ensures a high local geological confidence for mine planning but may have an exponentially increased time and monetary cost. This paper details the authors’ investigations into the geological uncertainty of IGO’s Odysseus Deposit, which is approximately 645 km north-east of Perth, Western Australia. At Odysseus, the komatiitic nickel sulfide mineralisation is irregularly cross-cut by nickel-barren pegmatites that have intruded and offset its thick ultramafic orebodies. These pegmatites generate significant uncertainty in the precision of Odysseus’ resource volume and tonnage estimates, as well as the subsequent quantification of pegmatite mining dilution in its ore reserve. To quantify the geological uncertainty in the pegmatite interpretations, IGO’s mineral resource practitioners prepared several geological risk studies over the Odysseus North lode, which is the lode most affected by the pegmatites. These studies included categorical conditional simulation of the pegmatites, preparing implicit geological models with alternative algorithms, trialling a machine learning application to prepare a maximum likelihood geological model, and finally assessing the early results of the pre-production close-spaced drilling to these different models. To assess the precision of the different single-outcome models, the authors’ compared the estimated pegmatite content of each model to the range of possibilities modelled by categorical conditional simulation within the planned stopes at Odysseus North. An estimation confidence score for each modelling method was then prepared for each alternative single-outcome modelling method. From these studies IGO concluded that a close-spaced drill pattern is essential at Odysseus, supporting the view of the Competent Person in 2017 who proposed a 25 m drill spacing in areas affected by pegmatite which had been partially classified as Inferred.

May 24, 2023

By D. McCarthy

This paper discusses the process involved in developing an optimum method of treating and removing heavy metals from water that have leached out from the native rock -prior to discharge back into the environment. Also designed into the system is a manner to stabilize the metals removed as a precipitate, so that they can be disposed of as a non-hazardous waste.

Jan 1, 1992

By A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effect of underground mining conditions on the activation of automatic sprinkler heads. Sprinklers were exposed to liquid fuel fires in a rectangular tunnel at airflows of 0, 45, 90, 150, and 250 m/min to determine the effect of ventilation and fire size on the time to activation. As the airflows were increased, the time to activate the sprinklers for a given fire size increased. Also, as the fire size increased, the activation time decreased. Temperature profiles of the tunnel showed that the maximum temperature near the roof was shifted downstream as the airflow increased. Experiments to determine the effect of rated activation temperature and response time index (RTI) value on activation time showed that the time to activate increased with increasing activation temperature, and decreased with decreasing RTI value. Exposure to the mine environment showed little effect on the activation times in large-scale experiments, and no significant effect in laboratory experiments. The results showed that airflow can have a significant effect on the activation times of automatic sprinklers. This needs to be considered in the design of effective sprinkler suppression systems for ventilated areas.

Jan 1, 2010

By Mario Gerards, Marco Steinberg, Jan Huben

"Wet high intensity magnetic separation or WHIMS is a widely used technical process for the recovery of magnetic susceptible iron ore particles, mostly for fine and ultrafine grain sizes. The JONES® WHIMS - Wet High Intensity Magnetic Separator, has been used for many years and in countries all around the world. This paper outlines the physical principles utilized for the separation inside the unit, as well as some of the recent changes and developments on the design. It will also give an outlook on the theoretical potential of different alternative yoke materials. The aim of this paper is to analyse the suitability of different yoke materials to improve the equipment. This will be done comparing the magnetic and mechanical parameters and analysing availability and price to find the best compromise regarding cost and benefit. As far as the different kinds of materials are concerned, a special material has been identified as suitable during the comparison exercise. After running the economical calculations, especially with respect to the reduction of the total power consumption of the equipment, a tremendous reduction of the total power consumption has been determined. In addition, to the theoretical exercises and due to the promising results of the same, the Pilot Unit P 40 of the JONES® WHIMS has been manufactured with the special material in order to get practical results as well. Finally, this paper outlines the theoretical and practical results focused on the power consumption. The results are showing that the total power consumption can be reduced tremendously. Hence, the way for a new generation of JONES® WHIMS - environmentally friendly - has been paved."

Jan 1, 2014

By M. E. Tyrrell

Research objectives were to determine the reasons for erratic behavior of semisilica horizontal zinc retorts in service; to investigate potential corrective measures including the possible utilization of more refractory materials in the retort body; and to delineate laboratory tests suitable for process control in the manufacture of retorts. Correlation of laboratory test results and data supplied by the cooperating smelters indicated that structural failures due to thermal shock and laminations in the retort body are largely responsible for the erratic behavior of horizontal zinc retorts in service. The most promising modifications made in the retort body and evaluated on a laboratory scale included finer grinding of the plastic clay fraction, substitution of mullite grog for calcined fire clay and grain alumina for silica, plus the use of an organic binder. Lamination-free extrusions having excellent thermal shock resistance were prepared from a mixture composed of 50 percent low-silica Missouri plastic clay through 100 mesh, 25 percent mullite grog through 6 mesh, and 25 percent alumina through 100 mesh. The mix was pugged under 28-inch vacuum with 1 percent ligno sulfonate binder in 12 percent tempering water. Laboratory tests suitable for process control in the manufacture of retorts are described.

Jan 1, 1969

These proceedings consist of an introduction, nine descriptive papers, and a summary. The first paper is an overview of the respirable dust research program, the second paper describes the Mining Enforcement and Safety Administration's proposed changes in the respirable dust enforcement program, and the third paper describes respirable dust measurement. The remaining papers, by Bureau and contractor personnel, describes methods of reducing the amount of respirable dust to which coal miners are exposed. Of the six methods of reducing exposure to respirable dust described, two are methods of preventing or reducing the amount of respirable dust raised during mining operations, two are methods of collecting or removing dust after it has been released into the mine atmosphere, 2nd two describe methods that are combinations of prevention and collecting .

Jan 1, 1977

By L H. Warren

The types of equipment available for generating a plasma have been reviewed. The efficiency and potential of the plasma generating equipment used in performing extractive metallurgical reactions have been determined. A general classification of the reactions that might be per-formed in a plasma has been proposed. Experimental work done on extractive metallurgical plasma reactions, heat transfer between the plasma and solids, and the quench of the products of plasma reaction has been summarized. From the preliminary results it appears that the high-intensity are or the transpiration-cooled anode plasma torch offer the most promising areas for further research. C ONSIDERABLE world-wide research effort is currently being devoted to the development of processing technologies which employ the new high-temperature generating devices that have appeared over the past few years. The plasma flames produced by these devices offer the potential for subjecting materials to any single gas or mixture of gases at temperatures up to 20,000°K. With these conditions available, many reactions in extractive metallurgy,

Jan 1, 1965

By R. D. Smith

The Bureau of Mines (BOM) evaluated the technology, capital investment, and annual operating costs of emission control for further reductions of lead in ambient air at the East Helena, Montana, smelter, and the Glover, Herculaneum, and Buick smelter-refineries in Missouri. This study seeks to analyze the technology available to the domestic primary lead industry for attempting to further reduce lead emissions below 1985 levels. Through enclosure of concentrate unloading and handling areas and all lead-processing buildings, followed by venting these enclosures to the atmosphere through baghouses and the application of appropriate local controls, emissions can theoretically be reduced by a total of 2,424 pounds of lead per day from 1985 levels at the three Missouri operations. Using conventional technology, aggregated additional capital costs of $250,014,000 and annual operating costs of $18,507,800 are estimated for the four operations, resulting in a total cost of $0.063 per pound of refined lead. Continuous drossing techniques would assist in meeting OSHA standards in process areas. Continuous drossing would change capital and operating costs to $258,344,800 and $16,104,700, respectively, for a total cost of $0.062 per pound of refined lead. First quarter, 1986 open market price for refined lead was $0.184 per pound.

Jan 1, 1986

By Robert S. Sanford

In April 1948, the Bureau of Mines was requested to evaluate the graphite deposit' known as the Benjamin Franklin and Just mines in Chester County, Pa. After preliminary investigation, it was recommended that the Bureau core-drill, trench, and sample the deposit and make beneficiation tests on the ore. During the first and second World Wars, flake graphite was in short supply, and a number of deposits in the United States were exploited. In 1942, the Defense Plant Corporation, through its lessee, the Benjamin Franklin Graphite Co., purchased 70.263 acres of graphite-bearing land and built a complete mining and milling plant with a capacity of 300 tons of crude ore per 24-hour day at a cost of $426,250 (Plancor No. 1254).

Jan 1, 1949

By David L. Veith

This Bureau of Mines bibliography of U.S. and Canadian literature pertaining to revegetating coal-mined lands contains 805 references published from 1977 to 1984. Each reference is evaluated by keywords, providing the reader with a means of rapidly sorting through the references to locate only those dealing with the coal mining region and subject of interest. All references are annotated. Other sources of information are given, including Office of Surface Mining (OSM) and State reclamation agencies and other published bibliographies.

Jan 1, 1985

By J. B. Rosenbaum

This report presents new findings and consolidates previously published data to provide a single reference containing a concise and comprehensive description of the Bureau's work on electrolytic chromium. Two separate systems for electrolytic-chromium recovery were developed, one designated as the oxidized system the other as the reduced system. The electrowinning of chromium metal follows the dissolution of chromium from the ore or from ferrochrome and its separation from gangue and metallic impurities. Chromite was first solubilized by pressure digestion at slightly elevated temperatures in an oxidized acid solution using Na2Cr2O7 as an oxidizing agent. Later it was found that a sodium-free electrolyte was preferable, using return-cell anolyte containing H2SO4 and Cr03 as the oxidizing agent. Gangue materials were separated from the soluble metallics by filtration; and, after the Cr+3 had been stabilized, the metallic impurities were separated as crystalline ammonium salts by vacuum crystallization.

Jan 1, 1957