Search Documents

By F. J. Cuddeback

For low-head pumping of small quantities of water, the water jet, or hydraulic educter, has been used to advantage by Eagle-Picher Mining and Smelting Co. in the Tri-State district. Water-jet pumps are used for draining sumps and pockets up to 15 ft. in depth. They have been used very successfully when only moderate amounts of water are encountered in taking up bottom. A small, easily handled unit is desirable in this work, especially while opening and deepening a new stope. Small air pumps are convenient but can be used only on the day shift, when air is available. Obviously, a jet pump of smaller capacity but operating 24 hr. prevents lost time at the start of each shift. No tests have been made on their power efficiency, but admittedly it is low. However, for certain kinds of work this is offset by their handiness, low initial cost, low upkeep, and reliability. They will handle slime and sand without ill effect, and will continue to pump indefinitely on air. This foolproof 24-hr. performance has led to their continued use at some places even after electric pumps with better power efficiency could have been installed. The success of jet pumps depends largely upon a cheap source of high-pressure water. Owing to mine depths in the Tri-State district, pump pressures range from 100 to 150 Ib. per sq. in. In many mines it is common practice to handle the normal inflow water with triplex pumps ranging in size from 3 to 8 in. The pumps operate 24 hr. per day, and, in order to handle emergency conditions, are speeded slightly faster than necessary to pump the normal inflow. The sump level is governed by controlling the by-pass water with a butterfly valve and float. This method is somewhat wasteful of power, but permits the pumps to operate with a minimum of attention. Such an installation is visited once a day to check lubrication. Hence, if some of this water, normally by-passed to the main sump, were used to operate a jet pump, the power cost could be considered low regardless of efficiency. Figs. I and 2 show two water jets that have done satisfactory work. The one in Fig. 2, made up entirely of pipe fittings, may be of interest partially because of its novelty, but does better work than its appearance indicates. The pipe fittings for this jet as shown cost $2.20. Some improvement in its design may be made by cutting out the 135 by 1¼-in. reducer to a smoother taper as shown by dotted lines. A 3-in. suction pipe is sometimes used in order that the discharge may be as straight as possible. A 2-in. discharge line has been used frequently, but 3-in. pipe is used where several hundred feet of discharge is required.

Jan 1, 1946

By William H. Mount

St. Joe Minerals Corp. has a long operating history of utilizing rubber-tired, trackless mining equipment in its Southeast Missouri Lead Belt underground mines. The company's first completely trackless mine, Hayden Creek, was opened in 1952, employing rubber-tired drill jumbos, electric shuttle cars, and articulated diesel trucks. The trucks were comprised of a conventional scraper tractor unit matched with a rear-dump rock wagon. These machines featured the first true earthmover tires to be used underground by St. Joe. The articulated truck concept proved to be very successful, and constitutes an increasing portion of the underground haulage today. St. Joe's second completely trackless mine, the Indian Creek property, was opened in 1954; conventional 9.1-t (10-st) rear dumps were used for haulage. Main haul roads were designed to be wide and fairly level to accommodate speeds of 32-40 km/h (20-25 mph).

Jan 4, 1976

By N. M. Langdon

In considering the magnificent success of Mr. Gayley's bold experiment of applying dry blast to the blast-furnace, whereby a saving of 20 per cent. of fuel per ton of iron is effected, the question arises whether still further economy in fuel is possible, and, if so, how it is to be attained. The manner in which the heat generated in the furnace is utilized in the production of pig-iron may be determined, by the method of Bell and Gruner, for any furnace for which the necessary data are obtainable ; and the study of the operation, under various conditions, of a number of furnaces, for which such information has been worked out, should enable us to form some conclusion on the subject. The tables and calculations here given cover the operations of several furnaces reported in our Transactions ; also the two furnaces using natural and dry blast ill Mr. Gayley's experiment, for which the heat-equation has been worked out by Prof. Joseph W. Richards in his admirable discussion ' of Mr. Gayley's paper, The Application of Dry Air Blast to the Manufacture of Iron, and, finally, various hypothetical furnaces. The full list is as follows : A. Isabella furnace, with natural blast. B. Isabella furnace, with dry blast. The data stated for A and B in Table 111. are those given by Professor Richards, except that the heat-units are given for one unit of iron instead of 100 units, and some items of heat supplied, as stated by Richards, have been subdivided, the total being the same as given by Richards. (Columns A and B are introduced in Table 111. for comparison with C and D.)

Jan 1, 1910

By D Piason

Newstan Mine commenced mining operations in 1887 and has since undertaken extensive mining within the Young Wallsend, Great Northern, Fassifern, Borehole and West Borehole coal seams using a range of mining methods including board and pillar mining and longwall mining.Newstan Mine is planning to extend the existing mine workings using longwall and miniwall mining methods to produce up to 4.5 Mt/a of run-of-mine (ROM) coal for at least 25 years. The planned extension in the Main East and South West sections will involve developing new longwall panels and related mains headings. The new area contains higher specific gas emissions (SGE) than previously experienced at Newstan Mine. To achieve the optimum ventilation requirements for the longwall operation in this new area, a new ventilation shaft was designed to be constructed using the blind boring method in the South West Headings section.This paper presents the shaft design parameters and selection criteria for the construction of the new ventilation shaft, including the construction phase and the holing process to connect the shaft to the underground workings. The paper also discusses future ventilation requirements for Newstan Mine.CITATION:Piason, D, 2015. South-west ventilation shaft project at Newstan Mine, in Proceedings The Australian Mine Ventilation Conference, pp 229–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

As part or a programme to raise lead smelter capacity from 65.000 to 140.000 tons bullion per annum. one new 1000 sq. ft. updraught area sintering machine replaced eight small downdraught machines.The metallurgical specifications were based on and laboratory tests at Mount Isa. Existing practice filtering concentrate as part of the charge preparation system and discharging wet filter cake to mixing was retained. This dictated a hot return fines circuit to maintain the required feed moisture content at low return sinter ratios.The engineering specifications provided for cenlralized control of plant and process, minimum operating labour, high plant availabi;lity and highest standardsof hygeine. Crushing and conveying capacity was set to cater for the most optimistic level of sintering capacity.On start-up a number of major engineering and hygiene problems became apparent, in addition to normal teething troubles. These problems have largely been overcome and reliable operation. at less than optimum production rate is now being achieved.

Jan 1, 1968

By Xiaoyan Luo, Congcong Dai, Gaipin Cai, Xin Liu, Lu Zong

To overcome the difficulty of accurately judging the load state of a wet ball mill during the grinding process, a method of mill load identification based on the singular value entropy of the modified ensemble empirical mode decomposition (MEEMD) and a probabilistic neural network (PNN) classifier is proposed. First, the MEEMD algorithm is used to decompose the vibration signals recorded under different load states to obtain the intrinsic mode components, and a correlation coefficient threshold is used to select the sensitive mode components that characterize the state of the original signal. Second, singular value decomposition is used to obtain the singular value entropy. Finally, the load state of the wet ball mill is judged based on the magnitude of the singular value entropy. A characteristic mill load vector is constructed from the singular value entropies of the cylinder vibration signals recorded under different load conditions and is used as the input to a PNN, which then outputs the predicted ball mill load state; in this way, a load state identification model is established. Grinding experiments are presented to verify the effectiveness of the proposed method, showing that the method can accurately identify the load state of a wet ball mill. ()

By M. Moseki

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Metallurgy of Materials) degree This paper presents the research into melting of scrap for job creation purposes in rural areas. The research was done on behalf of Mine Recycling Services (MRS), the company that will implement the project. The project involves the research into available cost effective and easy to operate technology. The paper covers the experimental and theoretical work that was conducted. The results were used to determine the best equipment and method for melting and casting brass scrap.

Jan 1, 2002

By Paul J. Henkels

Synthetic gypsum is the calcium sulfate co-product of a number of industrial processes. Synthetic gypsum utilization as an alternative to the naturally occurring mineral continues to grow in the gypsum industry. In particular, flue gas desulfurization (FGD) gypsum produced by the electrical utility industry has had a significant impact and a far-reaching effect on the gypsum wallboard manufacturing industry. This paper will discuss the various synthetic gypsum sources verses natural gypsum and highlight issues of use in gypsum wallboard and related products.

Jan 1, 1999

lv. H. Blauvelt, Great Falls, Montana (communication to the Secretary): In his remarks on Mr. Stetefeldt's paper (Trans., xxiii., 587)) Mr. Goetz observes: " Trouble experienced with producers at Great Falls influenced me to try Taylor producers instead of those of Wellman. But recent reports show that the Wellman producers work better, besides coating nearly 50 per cent. less than Taylor producers of equal capacity. Indiana and Illinois coals cannot be used in the Taylor producers by reason of the large size and hardness of the clinkers which they form." I think that Mr. Goetz must have been misinformed regarding the work of this producer in Illinois. One of the large mauafacturing concerns in that State, the Illinois Zinc Company, situated at Peru, which uses a coal mined in the vicinity, tried one Taylor producer, some four years ago, in competition with those of an older type, which it had been using. As a result of this trial, the company has now thirteen Taylor producers, which have been in operation for about three years. A recent report from these works says that the Taylor producers have largely reduced the loss of coal through the grate, and have also improved the quality of the gas, as compared with that produced from the same coal in the producers of the older type. This Illinois coal is, perhaps, the worst in the country for making gas; since, besides containing from 20 to 40 per cent. of ash, it carries a large quantity of pyrites, so that the clinkers are large and extremely hard, and the capacity of the producer is most severely tested.

Jan 1, 1895

By T. W. Eddy

Research was conducted in which elemental mercury and its sulfide mineral (cinnabar) are removed from a copper sulfide concentrate by low temperature thermal applications. The goal of this research was to reduce, volatilize, and collect mercury vapor from concentrated smelter feed in a simulated drying environment while maintaining the chemical integrity of the residual. The study used synthesized concentrates composed of copper sulfide and mercury bearing minerals (such as cinnabar (HgS) or elemental mercury) to determine optimal residence times and temperature ranges.

Jan 1, 1996

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"The thermal decomposition and regeneration behaviors of wüstite were investigated by in situ high temperature X-ray diffraction (HT-XRD) under non-isothermal condition at heating rate of 4 K min-1 in vacuum ranging from 294 K to 973 K. Wüstite on heating decomposes to magnetite and iron up to 823 K, above which it exhibits marked tendency to regenerate. Investigation of thermal stability of the reaction system shows that the decomposition proceeds under kinetic reaction control while the regeneration is under thermodynamic control. Kinetics study based on the Coats-Redfern integral approximation method indicates that the decomposition reaction follows a Komatsu-Uemura model-based diffusion-controlled kinetics with activation energy of 32.860 kJ mol-1. The thermodynamics analysis of regeneration reaction demonstrates that wüstite regenerates at lower temperature than stoichiometric ferrous oxide.IntroductionOwing to its importance in preparing various magnetic ceramic/metal nanocompostites or nanocrystals with high values of coercivity for the application as recording media, wüstite (non-stoichiometric ferrous oxide) has been attracting the attention of scientists over a long period [1-6]. The thermal behavior of wüstite was investigated by several researchers and phase transformations due to thermal decomposition and regeneration of wüstite during the heating in a specific temperature range was observed [7-9]. In spite of wüstite being found to dissociate to magnetite and iron at temperatures lower than 848 K and then regenerates at higher temperature, a clear understanding of the reaction mechanisms is clearly lacking [9]."

Jan 1, 2012

By Timothy Stark

Blasters are usually strictly liable for injury or damage caused by flyrock (trespassory invasion) and blast-induced vibrations (non-trespassory invasion). The application of strict liability to non-trespassory invasions has resulted in significant litigation that has hampered the use of blasting and the blasting industry. Stark (2002) proposes that blasters should not be held strictly liable for non-trespassory invasions but should be liable only if their conduct is proven to be negligent. This change in legal standard was proposed because improvements in blasting technology over the last thirty years allow blasting to be conducted without substantial risk of harm to property and thus the amount of harm imposed by a blast can be related to the level of care exercised by the blaster. It is anticipated that a negligence standard will reduce the amount of litigation because a plaintiff will have a greater burden to overcome. To facilitate the acceptance of a negligence standard by a court of law, this paper summarizes the standard of care using the 1977 Surface Mining Control and Reclamation Act, extensive U.S. Bureau of Mines research, and current blasting techniques, such as blasting mats. It is important for the blasting industry to promulgate a standard of care so a judge can feel confident that blasting can be routinely and systematically controlled and if the legal standard is changed from strict liability to negligence a subsequent judge or jury will be able to evaluate the level of care exercised by the blaster. This paper also suggests that the industry and/or ISEE develop and disseminate a comprehensive standard of care that courts can use to further justify a change from strict liability to negligence and evaluate the standard of care.

Jan 1, 2003

By Atulya Verma, Samantha Espley, Nashel Kalaka

Numerical modelling simulations of proposed mining sequences are used to evaluate mining induced stress concentrations and their migration associated with the progress of mining. This analysis is a standard practice for most prospective mining projects at various levels of feasibility study. The studies are usually initiated at the beginning of the mining cycle, on a global scale, and are maintained and updated throughout the life of mine (LoM) to identify or address local issues and the required remedies as and when needed. Developments in numerical modeling techniques along with advancements in computing technology and data storage/management capacity have given rock engineers access to a huge volume of data that needs to be analyzed and assessed. The most common approach to numerically evaluate stress concentrations and migrations in underground mines is to select the points of interest in a given volume such as the back of an excavation or points within pillars around critical infrastructure, and plot the stresses or a derivative of stresses over time to represent life of mine concentrations and migrations of stresses. The problem with this approach is the sharp gradient of stresses close to excavation boundaries. Slight changes in the location of selected points can change the stress concentration and migration patterns substantially and all generalized statements about LoM risk can be challenged in one way or another. For global stresses, the most common current approach of data analysis is by viewing series of pictures representing stress contours. In this approach, it is easy to overlook some critical detail and/or be masked by personal preferences of contour/picture representation. To overcome the problem of representing and analyzing huge volume of stress simulation data, the authors, through their experience at different mining operations, developed a volume-based technique to reliably evaluate mining-induced stress concentrations and migrations. The volume-based approach is for risk-based assessments of adjacent regions in the rockmass, in and around planned stoping excavations. The volume of interest is the entire ore body that is planned to be mined, but it could be just a part of the ore body depending on the specific use case. The risk identifiers are the induced stresses as compared to the strength of the rockmass. Over the LoM, the risk identifiers are tracked versus the corresponding excavation ratio of the zone. This approach is very effective in identifying the stages of mining that are contributing the most to the mining induced stress risk and the results can be used for proactive planning and mitigations measures such as alternative mining sequences, or stope sizes, or extraction methods. The approach has also been very successful in application at mature mines, particularly in assessing the re-initiation of mining in zone that has been dormant for some time. The volume-based approach allows for an assessment of the current state of the rockmass and the identification of future risks when planning resumption of mining activities.

Jan 1, 2023

By Ryo Sasai, Takeshi Itakura, Haruki Imaizumi, Hideaki Itoh

"Emission of industrial wastewater containing harmful oxoanions is one of the serious problems on account of its toxicity and the environmental pollution, especially caused by boric, phosphinic, arsenic and antimonic species. In this study, we developed a novel treatment technique of such polluted-water by hydrothermal mineralization. The treatment is “Geomimetic” method for precipitating oxoanions in aqueous media as natural ore resources by using hydrothermal treatment with calcium salts mineralizer. The treatment made it possible not only to detoxify the polluted-water, but also to recover the calcium minerals such as Ca2B2O5·H2O, Ca5(AsO4)3(OH), etc. Concentration of each ion in treated-water was lower than that of effluent standard in Japan. Moreover, the residual concentration of each ion was independent of the initial concentration, but it depends only on the solubility of the formed mineral under hydrothermal condition. Therefore, the hydrothermal treatment could be recommended as one of the treatment techniques of polluted-water.IntroductionVarious oxoanions such as boron and arsenic oxo-anions have high toxicity against human health and the environment. They are important resources, however, for plating or advanced material manufacturing industries[1-3], from which the wastewater containing these oxoanions is generated every day. An appropriate treatment is often required for industrial wastewaters to attain national effluent standards of Japan (NESJ, B: 10 mg/dm3, As: 0.1 mg/dm3). On the other hand, there is no production of arsenic and boric resources in Japan, and they are expected to be recycled. Therefore, the establishment of a system for the removal and recycling of arsenic and boron from wastewaters is of global significance.Several methods to remove them from aqueous media have been already reported by using adsorption[4], electro-coagulation[5], membrane separation[6-8] and biological techniques[9]. However, these methods have the following problems because of their stability in water. (1) Removal yield is low, especially for tri-valent arsenite ion (AsIIIO3 3-) and borate ion. (2) The applicable concentration range is narrow. In addition, the used adsorbents or collected residues after treatments are sill hazardous wastes, so that they must be treated by a proper method. But, it is very difficult to convert them to recyclable resources at most industrial plants. These problems are caused by the difficulty to recover these oxoanions as stable solid precipitates with low solubility in water. The establishment of recycling system of these hazardous compounds will be one of the world-important issues, especially, in Japan, which is poor in natural resources. On the other hand, compounds that contain high arsenic concentrations and are insoluble in water, are often found in natural minerals, for example, as haidinglite (Ca(AsO3OH)·(H2O) or Johnbaumite (Ca5(AsO4)3(OH)). This fact suggests that nature has an ability to produce insoluble As-bearing minerals. Similar phenomena can be found in case of boron, antimony, etc."

Jan 1, 2008

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

This study presents the results of the mineralogical characterization of Ti-Zr ore from the Jiboia deposit, located in the municipality of Brejo Grande, Sergipe State, Brazil. The goal is to identify the main Ti, Zr, and REE carrier phases in the different particle size fractions in order to subsidize the development of a cost-effective processing route for the production of heavy minerals concentrate. The mineral resources are estimated at 31.5Mt @ 3.5% of total heavy minerals (THM) for the Jiboia Ti-Zr deposit, of which 5 Mt @ 3.39% THM were classified as measured and indicated. The mineralogy of the heavy mineral concentrate recalculated to 100% is represented by 22% pseudorutile, 20% ilmenite, 15% zircon, 5% rutile, 2% monazite, and 36% gangue. The ore minerals are preferably concentrated in the 150 × 53-μm granulometric fractions, which represents 80% of the THM and only 27% of the ROM (Run-of-Mine) ore. Therefore, by cutting the ore to 150 μm, it is possible to discard 73% of the ROM mass and recover 80% of the THM, including 100% of the zircon and monazite which are the most valuable minerals present in the heavy mineral concentrate. The global recovery of THM starts to decline rapidly in the fractions finer than 106 μm and the mass disposal (tailing) does not follow in the same proportion. Higher zircon contents in the concentrates of the fractions finer than 150 μm imply a significantly lower recovery of heavy minerals like ilmenite, pseudorutile, and rutile that make the fractions coarser than 150 μm.

Jan 9, 2024

By J. W. Matousek

The heat content of the waste slag from a typical smelting operation methods for estimating the thermodynamic properties of smelting slags, to include: -- heats of formation -- heat capacities (specific heats) -- heat contents -- melting temperatures -- heats of fusion The techniques are illustrated with the analyses of a nickel reverberatory furnace slag from Copper Cliff, an iron-making blast furnace slag, and a "lateritic" slag from a ferronickel operation in Colombia.

Jan 1, 2007

From 1999 to 2008 rock related accidents accounted for 75 fatalities, nearly 6,000 injuries and almost 14,000 incidents (Pappas and Mark, 2011). Clearly this shows that rock related safety on coal mines remains a serious issue and more effort is needed to address this hazard. This paper reviews support design considerations and monitoring needed to improve rock related safety in room and pillar coal mines in the USA. From the present study design considerations continue to evolve and improvements in technology and a better understanding of failure mechanisms and methods to prevent these failures from occurring are in place. At first glance, the design of safe and efficient underground openings appears simple until the designer begins to realize the complexities and variability of geometries, geology, loading and stress influences, support designs and other factors such as corrosion and economics. Ultimately the goal of all designs is to ensure that it can be completed safely, last for the duration of the design life and it is economically feasible.

Aug 1, 2013

By T. Kerr, C. Mattich, J. Wilson

"In refractory gold concentrates, gold is occluded in sulphide minerals preventing efficient cyanide leaching. Hence, roasting is used to oxidize sulphur and organic carbon, the latter being necessary to minimize recovery loss through the preg-robbing effect. In 2009, Outotec commissioned the circulating fluidized bed roaster at Syama gold mine in Mali. Since 2013 Resolute and Outotec have been implementing improvements to the roaster performance with the capacity increasing from 8000 t/month in 2013 to above 13,000 t/month in 2016, while achieving a residual sulphide sulphur and organic carbon contents of below 0.1 wt.% and 0.4 wt.%, respectively. Thus a gold recovery in the CIL of above 90% is attained. In 2016, Outotec audited the Syama roaster. The analysis resulted in the Low Carbon Roaster (LCR) upgrade concept which (i) allows re-processing of calcine dust from the spray cooler and ESP after pelletization and (ii) allows the roasting of a further fine-organic carbon rich feed, i.e. de-slime circuit tailings. The LCR upgrade aims to reduce organic carbon to <0.2 wt.% and increase roaster-leaching gold recovery by >3%. Project development included extensive testwork. The LCR process is expected to become operational during FY 2019.INTRODUCTION Double refractory sulphide ores exhibit the characteristics of gold locked within pyrite grains, in the presence of preg-robbing natural (organic) carbon. Hence, to achieve high recovery during subsequent processing steps, i.e. cyanide leaching, oxidation of sulphide sulphur is required, producing a porous calcine by way of a roasting step. This allows for the gold contained within the pyrite grains to be accessible during cyanide leaching. Furthermore, it is necessary to oxidize the organic carbon. Oxidizing the organic carbon is essential as gold recovery loss occurs as a result of gold-cyanide complexes being adsorbed on organic carbon, this phenomenon is termed as preg-robbing (Miller et al., 2016). The gold absorbed on the organic carbon is lost, reporting to the tailings stream. Hence, the aforementioned oxidation of sulphide sulphur and organic carbon is the process goal. Nonetheless, the latter must occur at a controlled temperature which is concentrate/ ore specific, since the pores of the produced calcine should not sinter, as this makes the gold contained in the calcine less accessible during leaching, leading to gold recovery loss. The tight temperature control requirement is a decisive factor in the choice of a Circulating Fluidized Bed (CFB) as the roasting reactor, due to the excellent mixing characteristics of the CFB which results in temperature homogeneity of (+/-10°C). Roasting of double refractory ores, as described above, can be included in the flowsheet after comminution and grinding, a process termed as whole ore roasting, or by including a flotation circuit termed as concentrate roasting. Roasting the flotation concentrate results in less solid flow, increased sulphide sulphur grade and organic carbon content resulting in a higher heating value and higher gold content. A typical composition of the Syama ore and concentrate is given in Table 1. Ore average values presented correspond to the period 2015, while concentrate values are typical for the flotation performance throughout the period 2012–2015."

Jan 1, 2017

By W. G. Fischer

Basic laboratory tests on trona and the surrounding shales initiated the Rock Mechanics program. The stress-strain curve, modulus of elasticity, Poisson&apos;s ratio, the uniaxial rock strength, Mohr&apos;s envelope, the biaxial stresses at failure, and creep were investigated. A series of underground problems were then approached using this information and various field measuring devices, most of which were developed by the Bureau of Mines. Initially, stress concentrations near mine openings were evaluated using the stress relief technique. This required an accurate determination of the pre-mining stress field. Later, stress concentrations associated with the cave line were studied. After about 30 stress reliefs over an appropriate time interval the effects of one type of mining could be compared against another. The microseismic technique was used to investi- gate a possible application of warning devices near the cave line. A study of mine reorientation was made. Problems related to the shape and size of pillars and barriers were studied. The effectiveness of roof bolting patterns was examined. Control of roof stresses was attempted. A new system of mining in heavy ground has been developed using the information secured in the Rock Mechanics program. Without this system, mining in more than one instance would have been next to impossible. Indeed, from this one discovery alone, the Rock Mechanics program has paid off in improved safety as well as in dollars. The Westvaco trona* mine is located near the town of Green River in the southwestern corner of Wyoming. It is owned and operated by FMC Corp. on land leased from the US Government, the State of Wyoming, and the Union Pacific Railroad. A conventional room and pillar system is being used, (Fig. 1) with complete removal of the pillars during final mining. Return air bleeders surround

Jan 1, 1964

By M. S. Bickers

Prior to 1970, the environmental liabilities associated with mine construction and management were few. Mostly, they were aimed at health and safety matters. At that time less than two dozen codes were incorporated into the engineering design and they were somewhat static and well known by the engineering designers and managers. These codes issued by governmental agencies and professional associations are listed in Table 1

Jan 1, 1988