Search Documents

By J. Hanslovan, R. H. King

An investigation of the feasibility of shielding low-voltage trailing cables in underground coal mines is described. Both laboratory and under¬ground installation results are presented. The main objective of shielding is to reduce the electrical shock hazard; however, several problems will be encountered by mine operators who install shielded cables. Parameters related to such items as purchasing, splicing, troubleshooting, safety, and reliability are discussed. Some of these problems can be minimized by changes in cable constructions and shuttle-car reeling-device components. Both SH-C and SH-D constructions are considered.

Jan 1, 1979

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal.

Jan 1, 1989

By Qixiang Y

The strength of coal mass saturated with gas is an essential parameter in studying the mechanism of gas and coal outburst,and its prediction method. Up to now, there has not been a method for determining the strength of coal mass saturated with gas.This paper describes a new method whereby the strength of in-situ coal mass can be determined and stored continuously and automatically. The simulation results obtained in the laboratory indicate that the new method allows a fast, reliable, inexpensive and convenient determination of the strength of coal mass.

Jan 1, 1992

By Chris Mills

The role of gravity separation in the mineral industry is briefly considered in perspective. The mineralogical and laboratory approaches to gravity process design are examined with emphasis on process technology selection. The equipment available for small scale and pilot test-work is discussed, particularly in regard to scale-up and the acquisition of reliable, accurate data. Transposition of performance data from pilot scale to plant scale is explained. The available types of full scale gravity separation equipment are discussed with emphasis on large high-capacity units. Plant layout and selection of ancillary equipment are considered.

Jan 1, 1978

By Martin Bolesta

The use of strata injection as a means of stabilizing brittle and heavily stressed ground as well as faulted zones is now state-of-the art technology. Users are obliged to select the right combination from a wide range of injection products and equipment in order to ensure that the operation will be a success. Laboratory tests and a fundamental understanding of the technical aspects of injection products not only help in drawing up the correct injection procedure but have in fact become indispensable for planning the most reliable and cost-effective solution.

Jan 1, 2001

By R. D. Leitch

From time to time the Bureau of Mines has received requests from persons who wish to destroy unwanted explosives, and although the information that follows has been accumulated from sources considered reliable,4/ the. Bureau of Mines assumes no responsibility for accidents that may result from following the suggestions offered. Explosives to be destroyed may be fresh material from damaged packages, usable material for which there is no further need, or material that has deteriorated either from natural aging or from improper storage to the point where it is unfit for use.

Jan 1, 1945

Coal Mining machinery has undergone enormous changes in design and complexity of controls in the past 10 years. Specialised, high productivity equipment has been manufactured in Australia, in sufficient volume, to satisfy the local mullet needs.Local manufacturers face greater challenges from overseas competition, as well as increased customer demands to improve machine performance, productivity, quality, reliability and safety. In order to meet these demands now and in the future, it will be necessary to review work practises, and restructure production and quality systems to incorporate the latest principles and philosophies.

Jan 1, 1991

Large quantities of combustible materials are often found in underground metal and nonmetal mines, with support timber predominating. Wood lagging and timber, wires and cables, brattice cloth, hose, paper products, cardboard cartons, and wooden containers are additional combustible materials commonly found in underground storage areas. Shorted or overloaded electrical cables, worn sockets and plugs, spontaneous combustion, careless smoking, and welding and cutting are common fire ignition sources. Inexpensive, reliable fire detection and suppression systems are available to provide early warning and to extinguish fires that originate in underground storage areas.

Jan 1, 2011

By H. J. Booss

THERE is a considerable lack of data on thermody-namic properties of hard-metal alloys. Only two papers 1,2 give mean values of specific heat in an unknown temperature range; more recently the author3 gave more detailed information on the mean specific heat in the temperature range from 20" to -190° C.. EXPERIMENTAL 1) Method—Experimental procedure followed a method suggested by Oelsen and coworkers.4 It requires samples of some 100 g of weight. The time of measurement is prolonged (30 min) but one run allows the measurement of a lot of positions on the heat-content curve. Results4 were found to be in good agreement with "best values" given by kelley,5 Kubaschewsky and Evans,6 etal.

Jan 1, 1960

By K. R. Vost

"In situ" measurements of the surface heat transfer coefficient in underground airways by K. R. VeST,* B.Se. (Glas.), M.Se. (N.S.W.) (Visitor) Few "in situ" measurements have been made of the surface heat transfer coefficient in mine airways despite the importance of this coefficient in determining the heat flow into the ventilating air. In this paper, the values obtained at various air velocities and the comparisons of these values with theoretical values are given. Examples are also given ofthe errors which would result if rock surface temperatures were obtained by extrapolation from temperatures further into the rock without taking into account the time delay which occurs before a given change in air temperature reaches the points from which extrapolation is carried out.

By William H. Hamilton

Tunnel-driving capabilities in terms of feet per hour have advanced several hundred percent in the last century. Indications are that this capacity will double each decade for the next three decades. These future improvements will be made possible by a greatly increased need for underground excavation and the awareness of industry of its own latent capabilities. The factors of most interest to any potential user of a tunneling machine are those making possible an increase in production. The first and most obvious factor, and probably the one that has created the excitement and interest of most people, is the increase in boring rate through faster rock fracture and improved support systems. Boring rate can be increased by more horsepower in the form of increased thrust, torque, and cutterhead speed, and by better cutters and cutting methods, better material-handling systems, and better ground-control systems. All of these items are extremely important and are the basis of much discussion and effort by everyone concerned with the excavation of tunnels by machine. The second factor, just as obvious and equally important as an increase in boring rates, is "increase in production through better utilization of the tunneling machine and related equipment," which means a reduction in downtime through greater reliability of equipment. Mechanical rock attack is presently capable of cutting hard rock at 5 fph and soft rock at more than 20 fph. In current practice, however, this advance rate is maintained for less than 50% of the shift time. I predict that tunnel-driving contractors and their supporting manufacturers of tunnel-boring equipment will provide machinery that will maintain these advance rates for more than 90% of the shift time. This increase in effective production will be due to the increase in reliability of the tunneling machine and tunneling system components. Such a percentage increase in utilization of the tunneling equipment is just

Jan 1, 1970

By C. P. Lazzara, Y. Miron, A. C. Smith

This report presents a U.S. Bureau of Mines study to identify the causes of self-heating events beneath the floor of a deep underground coal mine. Mine samples from both heated and unheated areas were examined by various techniques, including visual, microscopic, thermal, chemical, and instrumental tests. The combined results led to the conclusion that pyrite (FeS2) oxidation was the prime cause of the beatings. However, adiabatic oven tests of selected samples did not indicate the effect of the pyrite on the self-heating process, probably because of the experimental conditions. A fast, simple procedure to assess the concentration of pyrite in the mine samples was developed, utilizing the reactivity of the sample with an aqueous solution of hydrogen peroxide (H2O2)

Jan 1, 1992

By M Lewis, A Cook

This paper is based on the technology and functionality of a Modular Mining IntelliMINE« system which is a real-time decision-making tool. The IntelliMINE« system, incorporating Dispatch, is a fully Integrated Mine Management System. Measuring, quantifying and analysing the performance of mining is considered a fundamental and strategic step towards changing the nature of technical and operational decision-making at the majority of international mining corporations. Successful implementation of electronic data capture devices and computerised tools have enabled many mining operations to improve their competitive position with an improvement in the utilisation of the key assets, mineral resources, capital mining equipment and human resources. Real Time Mine Management Systems are designed to direct the emphasis away from collecting data and focus decision makers on the real issues with well-presented and reliable information. The systems provide a common stream of information to enable senior management, operations, maintenance, technical and process plant staff to make complementary decisions based on reliable, accurate and timely data. The mine asset information tools focus all employees on performance and give them feedback on their area of responsibility. The resulting tangible benefits can be delivered in different forms depending on the mining method, ore type, workplace culture and the current competitive position. Typical areas of improvement reported by system users are:reduction in capital expenditure on mining equipment fleets; more effective planning and budgeting parameters and procedures; increased control over ore-extraction and processing; increased employee accountability and organisational performance; and improved co-ordination between planning, operations, maintenance and processing. These improvements can be delivered in different forms depending on the status of the mine and commodity markets. In times of market oversupply and low commodity prices, the benefits can be delivered to the bottom line in terms of reduced cash costs, reduced capital and operating resources to maintain constant production. In times of market expansion, existing capital resources will be more productive delivering increased production and revenue. Mine management systems have the potential to transform a traditional mine operation into a learning organisation with an improved understanding of the critical performance issues and enable development of relevant strategies to continually identify and eliminate operational inefficiencies. The effectiveness of each strategy and operational change can be accurately monitored and its success (or otherwise) will be quantified. The latest downturn in the world metal prices has forced many mining companies to focus on cost reduction and productivity improvements as a means of remaining competitive. Maintenance represents a significant proportion of the overall operating costs in the mining industry. A structured proactive maintenance approach such as Reliability Centered Maintenance (RCM) can achieve significant cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled, thereby reducing costs and interruptions to production.

Jan 1, 2000

By Glenn C. Reed

This report is one of a series based upon investigations made and being made within the Missouri River Basin in Montana by engineers of the Bureau of Mines , Albany Branch , Mining Division . These investigations are made primarily to provide preliminary information to the Department of Interior agencies and to others concerned with planning the proposed Federal power development within the Missouri River Basin . The present report has been designed to permit public distribution of factual data obtained . The field investigations were made during the late fall of 1947 and the summer of 1948. Information on mineral occurrences in several areas in Sweet Grass County also are included in this report because of their close proximity to Park County . Practically all known metallic mineral deposits within Park County were investigated ; some nonmetallic mineral deposits also were investigated. The investigations of the metallic mineral deposits in Park County cannot be considered complete ; some long inactive mines and prospects on which little or no information is of record may have been missed . Many of the underground openings , especially at the long inactive properties , no longer are accessible ; consequently , much of the information regarding history their and development necessarily has been obtained from available Federal and State publications .

Feb 1, 1950

By L. B. Pankratz

Enthalpies above 298° K were investigated for four crystalline sodium borates by copper-block drop calorimetry. Determinations were made to 1,200° K for NaB02, 1,003° K for Na2B407, 1,005° K for NaB305, and 1,046° K for Na2Be013. No phase transitions or other thermal anomalies were found. The enthalpy determinations, when combined with known heats of formation at 298° K and other supplementary data, enabled the calculation of the heats and free energies of formation of the compounds to their melting points. Values of relative enthalpies, entropies, heat capacities, free energy functions, enthalpies of formation, free energies of formation, and equilibrium constants of formation were tabulated at even temperatures.

Jan 1, 1971

By J. Weng

The equations of heat conduction are numerically solved for two kinds of artificial freezing- mechanical freezing and liquid nitrogen freezing. A two dimensional finite difference model simulating the freezing field is developed. The procedure introduces a way to simulate the effect of latent heat released when water transforms from liquid to solid. The procedure also produces a way to calculate the harmonic mean of heat conductivity used when dealing with heterogeneous material. The theoretically derived temperature distributions in frozen soil are given and compared with measured data. An analysis made on the thermal design in shaft freezing. The average temperature of frozen soil is calculated by using numerical integration. The regularity of development of frozen soil radius is revealed and given in an appropriate mathematical model.

Jan 1, 1984

By C. F. Jr. Nagel

THIS paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. HEAT TREATING Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this improvement may be illustrated by the typical properties of duralumin (Table 1). It is essential that the material be in the wrought condition in order to obtain maximum heat-treatment effects.

Jan 1, 1927

By P Barrette

The manual gravimetric drying moisture determination methods currently employed by most mineral processing plants fail to provide timely and accurate information required for automatic control. The costs associated with transporting and handling concentrates represent a major portion of the overall treatment price. When considering the cash flow of a mining operation that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, any tool that provides real-time feedback on the process is vital (Edwards, RP 1994). The introduction of an on-line moisture sensor would become a welcome addition to the process control field instrumentation package now applied. A novel on-line determination system for ore concentrate moisture content would replace the tedious manual procedure. Since the introduction of microelectronic-based control systems, operators have strived to reduce the treatment costs to the minimum. Therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the æwish listÆ of mineral processors since the problem has always been that you can only control what you can measure, (Konigsmann, 1990). Today, the task of moisture determination is still done by the classical technique of loss in weight utilising uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of seven to nine percent, but controlling the moisture content below eight percent is a difficult task with a manually controlled system. Many times, delays in manually achieving reliable feedback of the moisture content results in the moisture varying from five to twelve percent before corrective actions can be made. This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper introduces and describes a unique and promising novel on-line moisture sensor employed for mineral processing de-watering applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimisation of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarise the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content. The commercial model of the equipment is described with the features and benefits to the users summarised.

Jan 1, 2003

By Jeanne A. Zimmer, Andrew B. Cecala, Edward D. Thimons

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U. S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations. INTRODUCTION Face ignitions are a concern for many U. S. longwalls and will continue to be until better control technology can be developed or until reliable and accurate knowledge can be provided as to when an explosive concentration is present. Figure 1 shows the number of reported U. S. underground longwall ignitions from 1980 to 1990. The number of longwall panels have remained relatively constant over this time period with 89 reported in 1980, compared to 96 in 1990. In spite of technological improvements in mining over the past decade, no significant reduction in the number of longwall face ignitions has occurred. One factor contributing to this is that the U. S. coal industry is mining gassier seams causing methane liberation rates on the average to be higher (Trevits, 1991; Grau, 1987). Another factor is the development and implementation of more reliable, heavy-duty longwall face systems that are generating higher production rates and higher methane liberation rates. Additionally, the average panel width in 1991 was 714 ft; a 44 pct increase from 1980 when faces averaged a width of 495 ft (Merritt, 1992). Increases in panel width also impact total face methane emissions. [ ] There have been substantial advances in control technology in the areas of methane drainage, methane containment, and methane dilution. In some mines, efforts to drain methane in advance of mining have proven effective, but geological conditions often preclude this approach (McCall, 1984; Ely, 1989). In other cases, ventilation air quantities of over 100,000 ft3/min and face velocities of over 1,000 ft/min have been implemented on longwall panels. Other operations have implemented anti-ignition spray systems which use water sprays behind each cutting bit to quench the hot streaks created from cutting noncoal materials (Courtney, 1990). Other control techniques, such as the modified shearer clearer system and ventilated drum, have been used to increase the amount of turbulence and ventilation around the cutting drums, thus reducing methane levels (Cecala, 1986; Divers, 1987).

Jan 1, 1993

By John P. Dolan, Charles A. Einarsen, GiIman A. Hill

his paper discusses how the following formation characteristics can be determined mathematically from drill-stem test pressure charts: true formation pressures, effective permeability of the entire section tested, well productivities, wellbore damage, and possible detection of barriers (faults, pinchouts, etc.). This paper also presents a practical method for im-mediate determination of eflective permeability and well-bore damage from successful double shut-in pressure tests. A list of recommendations for improving the reliability of drill-stem rest pressures is also presented. INTRODUCTION A drill-stem test is a temporary completion designed to sample the formation fluid and to establish the possibility of commercial production. Early pressure recording devices were used merely to verify proper operation of the testing tool. Until recently the accuracy of the pressure gauges has been insufficient for any reliable quantitative use of the recorded pressures. In view of the need for more reliable formation evaluation and as a result of the recent interest in exploration work employing the concept of hydrodynamic en-trapment,1,2,3,4 better pressure recording gauges are now in use. These devices can record pressure within 1 per cent above 1,000 psig and can detect differential pressures as low as 1/2 psig. In addition to formation pressure, several other reservoir characteristics can be determined from DST charts; namely, well productivity, formation permeability, wellbore damage, and the possible existence of bar- riers (faults, pinchouts, changes in permeability, etc.). This paper presents a practical method to interpret DST pressure charts for formation pressures and many other reservoir properties, a method that has been developed in analyzing approximately 4,000 DST charts during the last five years. The techniques used are a composite of published articles on drill-stem testing5,6, together with well-known pressure build-up analysis methods. THEORY It has been shown7,8 that the following equation may be used for analysis of pressure build-up curves: Po - Pw = 162.6 qu/kh log ( to + ?/?) .....(1) When this equation is applied to the curves obtained in drill-stem testing, the assumptions and boundary con-ditions are more nearly realized than in conventional flow and build-up tests on producing wells. Zak and Griffen9 have recently discussed in detail the use of this equation in analyzing DST charts. One of the problems with DST curves is the lack of reservoir data for precise analysis. Therefore, it is necessary to develop empirical rules and field methods for analyzing DST charts in quantity. For this reason, the empirical methods presented in this paper have been developed, and their derivation is found in Appendices A and B. METHOD USED FOR ACCURATE READING OF DRILL-STEM TEST CHARTS In order to apply the pressure build-up theory to DST charts, it is necessary to obtain a digitized expression for the pressure and time data recorded by the pressure gauge. These data may be either provided by the service company or interpolated by projecting a

Jan 1, 1958