Search Documents

By Martin B. Schranz

Copper sulfate pentahydrate is recovered from the spent etchant waste stream of a printed circuit board manufacturing facility by cooling crystallization. The fluidized bed crystallizer contains submerged cooling surfaces which are bathed in a stream of air. The air bubbles provide agitation which improve heat transfer, reduce fouling and maintain crystals in suspension. The recently patented apparatus (US 5,523,064) has advantages when compared to a conventional surface cooled crystallizer including capital cost, ease of operation and production of larger more uniform crystals

Jan 1, 1997

By S. Ross, M. Mayhew

"Kirkland Lake Gold introduced battery equipped vehicles (BEVs) at the Macassa Mine in 2011. The fleet of underground BEV haulage trucks and loaders has grown over the years to over 30 units, the world’s largest, currently handling approximately 80% of the daily production tonnage. The inflow and outflow of air occur through a limited number of relatively small openings, which limits the air volume delivered to the underground workings. In addition to improving air quality, the reduced heat load generated by the BEV (when compared to diesel equipment) had a significant positive impact in the workplace. The use of BEV for material handling has enabled increases in production that would not have been possible using diesel equipment.INTRODUCTIONMacassa mine was developed as a track-drift access mine, with the most recent shaft (#3) sunk in 1986. A new mining complex, the South Mine Complex (SMC) was discovered below the 5025 foot elevation south of traditional mining areas, and the majority of mining now occurs in the SMC. The discovery of that zone has led to an internal ramp which is used to access the SMC and haul ore to #3 shaft.The amount of airflow that can be moved through the mine is limited by the existing infrastructure to surface. This amount was recently increased to near its practical maximum from 118 CMS (250 kCFM) to 151 CMS (320 kCFM).Both diesel and electric equipment are used at Macassa. Tethered Load-Haul-Dump Machines (LHDs) have been replaced with Battery Electric LHDs, due to their increased mobility and depth of the mine. Battery trucks continue to replace locomotives to transport both ore and waste to the shaft, as mining has transitioned from tracked levels to trackless level and haulage has transitioned from horizontal levels to an inclined ramp.EQUIPMENT FLEET AT MACASSAMost of the primary material movers utilized at Macassa Mine are battery operated. As the mine goes deeper the battery technology will continue to be critical to the success of the operations. With over 300,000 hours of proven operation success, the battery technology and equipment will continue to be a major part of Macassa’s future."

Jan 1, 2019

By Baozhong Zhao

In-situ vitrification (ISV) is a new technology used for treating radioactive, organic and inorganic contaminated soils. In this process, electricity is applied through electrodes buried in the contaminated soil to melt it and form an environmentally stable glass-like solid. The organic contaminants and volatile metals are vaporized during heating up, the non-volatile inorganic elements are dissolved and incorporated into the melt. In present full-scale operation, the ISV process can treat 4 to 6 tons of soil per hour at consumption of about 1000 kwh per ton of soil. In this study, various configurations of electrodes were examined in a mathematical model. The results may be used to optimize the ISV process.

Jan 1, 1994

By J. Shibata, N. Murayama, H. Yamamoto

As one of effective usages of wastes discharged in the non-ferrous metal industry, the syntheses of AlPO4-5 and hydrotalcite were carried out using aluminium dross as a raw material. AlPO4-5 is an aluminium phosphate condensate with properties of zeolitic materials and large pore size. Hydrotalcite is an inorganic anion exchanger and has a layered structure of complex hydroxide. They were synthesized in an autoclave at high temperature and pressure. Various physical properties such as crystal structure, surface texture, and specific surface area were measured. AlPO4-5 can be synthesized from aluminium dross under hydrothermal conditions at 180°C-200°C, and 3h. At the same time, AlPO4-34 and non-porous AlPO4 were also formed as by-products. The crystals of AlPO4-5 have a hexagonal structure. Lt is desirable to heat the reaction product at around 550 °C to remove tri-ethyl amine. The specific surface areas of the reaction product before and after heat treatment at 550°C were 17.9m2/g and 358m2/g, respectively. Hydrotalcite can be obtained by a co-precipitation method from the aluminium dross and waste MgCl2 solution discharged in the aluminium regeneration process. Small amounts of SiO2, Al2O3, and Fe2O3 remain in the reaction product as an impurity component. The interlayer distance of the obtained reaction product is about 0.3 nm. Hydrotalcite changes to Mg-Al oxide during calcination at 500 °C for 3h, and then hydrotalcite is formed again by a rehydration operation. The physical properties of the reaction products obtained from the wastes were very similar to those from fresh reagents.

Jan 1, 2004

By J. K. Brimacombe

Since the Peirce-Smith converter was introduced to the non-ferrous industry in the early part of this century, there has been a paucity of research on process-engineering aspects of the reactor such as gas injection. This paper reviews studies conducted at UBC over the last decade on gas discharge dynamics, high-pressure injection, bath slopping, oxygen/bath reaction kinetics and out-of-stack heat transfer within the converter. The ultimate objectives of this work have been to extend refractory life and to increase converter productivity.

Jan 1, 1985

By N. H. Coates

The Bureau of Mines designed, constructed, and operated an 18-inch- diameter, fluidized-bed combustor for highly caking coals to evaluate the method for possible application to power generation. In initial tests, combustion was carried on successfully, with carbon losses as low as 0.8 percent. Coal ash was not satisfactory as a bed material, but mullite proved to be acceptable. Overall heat-transfer coefficients from the bed (-20 + 50 mesh mullite) to a water-cooled tube were about 75 Btu/hr-ft2- °F.

Jan 1, 1970

By Jean-Christophe Gebelin, Mark Jolly, Samantha Jones

"The de-waxing process in investment casting is truly a black art which is carried out in a black hole - the autoclave. The process involves exposing wax, coated by a porous ceramic shell, to steam at a pressure of 10 bar and a temperature of about 180°C. The processes which then occur are truly multi-media and multi-physics. Steam condenses in the porous ceramic, wax melts and flows, the shells expand and sometimes crack. Why the shells crack is one of the most difficult questions asked in the industry.Modelling and validating the de-waxing process is not simple. The IRC at the University of Birmingham is attempting to model this process using Physica+ a code developed in the UK. This paper will present the latest results in this attempt to model one of the casting industries most intractable problems.IntroductionThe de-waxing process using an autoclave involves the following physical phenomena:· Flow of the steam in the autoclave;· Heat transfer from the steam to the wax, possibly through the shell;· Melting and flow of the wax.At the same time, other phenomena may occur, such as the flow of the steam through the shell, the condensation of the steam on the shell surface and on the wax pattern surface, the flow of wax the through the shell, etc ...This shows how complex the de-waxing process is from a physical point of view. The main defect that appears during this process is the cracking of the shell. Previous modelling work carried out by Snow [1] has shown that it is possible to predict the stress in the shell, making numerous assumptions. In this paper, the modelling to predict the state of stress in the shell that is currently in development at the University of Birmingham is presented together with the presentation ofthe physical phenomena to model and the assumptions used. The parameters that are needed in such models will also be discussed, and some experimental work undertaken at the moment presented."

Jan 1, 2001

By S. Sundarraj

The morphological transition between columnar and equiaxed structures is an important solidification phenomenon frequently observed in castings, especially complex parts with varying cross-section, The mechanical properties and the occurrence of defects such as hot tears are strongly dependent on the structure formed in the casting. Hence, it is important to understand the conditions leading to columnar or equiaxed structures. Although extensive work has been done in modeling solidification systems, almost all of the existing models are based on the assumption that the structure formed in the casting is either purely columnar or purely equiaxed. Prediction of the columnar-equiaxed transition (CET) requires a solidification model which accounts for the formation of both columnar and equiaxed structures, along with related microscopic and macroscopic solidification phenomena. In this paper a CET model is presented which: (i) takes account of both columnar and equiaxed structures, (ii) accounts for macroscopic heat transfer coupled with microscopic phenomena such as nucleation, growth and microsegregation, (iii) satisfies solute conservation, and (iv) is easy to implement in commercial finite element and finite difference software. The proposed model predictions of CET have been validated with available experimental results for a uni-directional solidification of an aluminum-copper alloy. A sensitivity analysis has also been carried out to determine the effects of various parameters on the CET model predictions. The model is being extended to other alloy systems and more complex geometries. This work will be published in due course.

Jan 1, 1996

By Richard D. Miller

This publication contains routine analyses and related source data for 350 natural gas samples from 19 States collected during calendar year 1362 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Helium Activity of the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus. Four previous publications have been made to present the results of 5,648 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1962. The first, Bulletin 486, 3/ contains analyses and data on 2,195 gas samples collected during the period 1917-47. Bulletin 576, 4/ the second publication, includes data and analyses for 1,575 samples collected from 1947 through May 1956. The third bulletin contains 1,444 analyses and source data of samples obtained from May 1956 to January 1, 1961.

Jan 1, 1964

By Richard D. Miller

This publication contains routine analyses and related source data for 350 natural gas samples from 19 States collected during calendar year 1962 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Helium Activity of the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus. Four previous publications have been made to present the results of 5,648 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1962. The first, Bulletin 486, 3/ contains analyses and data on 2,195 gas samples collected during the period 1917-47. Bulletin 576, 4/ the second publication, includes data and analyses for 1,575 samples collected from 1947 through May 1956. The third bulletin 5/ contains 1,444 analyses and source data of samples obtained from May 1956 to January 1, 1961.

Jan 1, 1964

By Dengfu Chen, Huabiao Chen, Yunwei Huang, Mujun Long, Youguang Ma, Lintao Gui

In the current work, a three-dimensional model coupling turbulent flow, heat and solute transport was developed to investigate the solute transport and redistribution in the mold of slab continuous casting where the Reynolds number is very high and the molten steel flows strongly. The conservation equations of momentum, energy and species for a multicomponent system which includes solute element C, Si, Mn, P, S were solved with the commercial software ANSYS Fluent. The parameters used in the model are based on the actual continuous casting. The fluid flow, temperature distribution and solute elements distribution were analyzed. Results showed that negative segregation occurred near the strand surface, and the species concentration reached a peak value at the solidification front during solidification. The segregation degree of solute element S is higher than the other solute elements because of its lower equilibrium partition coefficient. The species concentration in the liquid pool is homogeneous because of the turbulent flow effect.

Jan 1, 2015

By D. W. Rierson

Svedala has a ported kiln process, designed specifically for the direct reduction of pelletized or natural lump iron ores. The process is called ACCAR. This ported kiln technology has been coupled with Svedala's GRATE-KILN System, for iron ore pelletizing, into the GRATE-CAR System for the reduction of fine grained ore concentrates through the steps of agglomeration, induration and reduction in a single production line. Additional applications of the GRATE-CAR System include: the recovery, agglomeration and reduction of steelmill waste oxide fines and the use of minus 6mm size natural lump ores to produce a highly metallized pellet agglomerate. Svedala conducts tests to confirm certain operating parameters through process simulations of the GRATE-CAR process. These tests are conducted at Svedala's Process Research and Test Center, Oak Creek, Wisconsin. Svedala also assesses issues of process variables, heat transfer, equipment sizing, retention time and endothermic demand associated with iron ore reduction using natural gas or coal as the reductant. The purpose of this paper is to present the GRATE-CAR processing concepts, the commercial production line and the testing procedures associated with investigating potential raw materials.

Jan 1, 1997

By Joseph Licavoli, Paul Sanders, Yang Yang

"Al-Sc-Zr alloys form thermally stable L12 precipitates which provide high temperature strength. Although the overall fraction of L12 Al3Sc and Al3Zr may be increased by increasing scandium (Sc) and zirconium (Zr) content, such additions may increase primary phase fractions and do not produce desirable secondary phase morphologies. Rapid solidification techniques, such as melt spinning, increase solute atom concentration within the matrix. When the supersaturated matrix is aged, higher precipitate volume fractions at low Sc and Zr levels can be achieved improving high temperature strength. Melt spinning was used to rapidly solidify (107 k/s) a thin ribbon of Al-0.5Sc-0.4Zr at. %. The ribbon was compacted and extruded into 99.8% dense rods, and then aged using multi-step isochronal heat treatment up to 600°C. Precipitation strengthening was evaluated by ambient hardness measurement. The ambient hardness of melt-spun ribbon after precipitation hardening increased by 450 MPa (~67% increment) during isochronal heat treatment.INTRODUCTION Small Sc and Zr additions to aluminum improve strength and creep resistance above 300°C due to tri-aluminide precipitation of Al3(Sc,Zr) in L12 structures similar to ??, Ni3(Al,Ti) in nickel superalloy, but the Al3(Sc,Zr) particles have a Sc-rich core surrounded by Zr-rich shell (Figure 1). The Al3Zr shell limits atomic transport between the Al3Sc core and the matrix and reduces coherency strain. These factors reduce precipitate coarsening rate at elevated temperature (Bergner & Van Chi, 1977; Fujikawa, 1997; Knipling et al., 2011; Clouet et al., 2006).Figure 1. Simplified schematic model of precipitate Al(Sc,Zr) in Al-Sc-Zr alloy. Shell is rich of Al(Zr) intermetallic phase, particle core is rich of Al(Sc) intermetallic phase (after Voorhees, 2006). Numerous Al3(Sc,Zr) particles increase alloy strength and creep resistance as the precipitates impede dislocation glide and to a lesser extent climb. Previous work on ternary Al-Sc-Zr alloys show large strength increases versus binary Al-Sc, and Al-Zr alloys in Table 1."

Jan 1, 2018

By HENRY M. HOWEL

1. Introduction.-The first part of this papers treats of the causes and the restraining of piping in steel ingots; the second& considers the causes and the restraining of -segregation; and the third proposes certain precautions in engineering specifications concerning these two defects. Into their causes I have looked carefully, with the purpose of arriving at rational methods of restraining them, and at efficient ways of detecting. and measuring the harm which they cause, so as to benefit the public by reducing this harm at once effectively and with the least expense to the manufacturer, and therefore in the end with the least expense to the consumer. In Part I., I infer that the pipe is chiefly due to what I, call the virtual expansion of the outer walls of the ingot in the early part of the freezing. I find that the upper and smooth-faced part of the pipe probably forms while the interior is still molten, but that the lower, steep, and crystal-faced part probably forms in metal which is already firm. Of the five causes which may co-operate to limit the depth of the pipe, I find that three-blow-holes, sagging, and the progress of freezing from below upwards-are usually effective. I find that the pipe may be lessened by casting (1) in wide ingots,; (2) in sand molds, especially if these are pre-heated (this is rarely expedient); (3) at the tops instead of at the bottom; (4) slowly; (5) and with the large end up; (6) by the use of a sinking-head or other means of retarding the cooling of the top; (7) by permitting blow-holes to form; and (8) by liquid compression.) Most of these I consider in some detail, and in particular I dwell on the advantages of casting with the large end up, and I propose certain administrative arrangements to permit this.

Mar 1, 1907

By B. A. Wills

With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the very fine mineral particles in these ores. Not only is this expensive but it leads to greater losses in 'slimes'. In the early 1970's, 50% of the tin mined in Bolivia, 30% of the phosphate mined in Florida and 20% of the world's tungsten were lost in this way (Somasundaran, 1979). Gravity concentration techniques become unacceptably inefficient for particle treatment below 25-50µm, and even flotation fails in the ultra-fine range. Two approaches can be adopted to try to overcome this problem. The first involves increasing the efficiency of existing equipment or developing new slimes treatment processes. Gravity devices such as the Bartles-Mozley concentrator have been developed for this purpose and good recovery has been reported from 100µm down to 5µm. Such machines, however, have relatively low throughputs, so that large areas of plant space are generally required. Flotation is rapidly growing in importance for the treatment of ultra-fine minerals traditionally treated by gravity concentration.

Jan 1, 1986

By Alan M. Jessop

This paper discusses the distribution of frozen ground in the zone of discontinuous permafrost in relation to the pattern of surface temperature. The importance of understanding permafrost in relation to surface construction and open-pit mining operations is stressed.

Jan 1, 1972

By Edo Engel

Hot Blast Stove Technology has been developed to such an extent that low cost hot metal production for over 30 years without major repairs has become achievable, making the decision for a campaign length between 5 to over 30 years a design choice for the plant owner/operator. Some of the earlier examples of designs capable of such long campaign lengths are currently close to the 50th year of their running campaign. These examples are found especially in Europe and North America. Along the duration of these campaigns, repairs to subsystems such as burners, hot blast outlets etc. may be required. Depending on a plant’s up and down stream production capacities, the repairs may have to take place in the shortest possible time frame to minimize production loss. This article discusses an approach for intermediate repairs, executed while keeping the majority of the system at operating temperature.

Oct 30, 2017

By Antti J. Perala, Teemu J. Yli-Kovero

"Efficient use of land is constantly requiring more underground construction. Minimized execution time and disturbance to surroundings and nearby structures are essential benefits for all construction techniques. To meet the demands of a modern construction project, suppliers have to be able to provide high-quality and tailor-made products just on time. RD pile wall is a retaining wall based on drilled steel pipe piles which are connected to each other with special interlocking profiles. RD pile wall is a solution which enables penetration of overburden soil, dense fill layers including stones and boulders, and embedding into the bedrock in one single operation. Several test installations and laboratory tests have been made to develop the system and to test and improve the water tightness of the wall. Beside these tests, RD pile wall has also proven its reliability in almost 70 projects. Largest project so far has been Pasila Tripla project in Helsinki, Finland. A permanent retaining wall with surface area of 18,000 m2 (193,750 ft2), excavation depth of 21 m (68 ft) and over 17 m (56 ft) of water pressure was made with 711 mm (28”) and 406.4 mm (16”) pile sizes. Piles were delivered to site in one piece with lengths up to 33.5 m (110 ft).INTRODUCTIONExcavations in cramped city centers and in between of existing buildings and other structures are facing more and more challenges. Installation of sheet pile walls is often problematic or even impossible due to obstacles in ground from old structures and due to demand to extend the excavations to even deeper and harder soil layers. Also installations of secant pile walls are facing difficulties due to cramped construction sites and constantly tightening execution times.On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid- 1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall, was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers).PRINCIPLE AND MAIN BENEFITS OF THE METHODRD pile walls can be used in all soil conditions. Most beneficial the system is in extremely demanding soil conditions where the installation of traditional retaining walls is challenging or even impossible. The RD pile wall is a combination of drilled steel pipe piles and interlocking sections as shown in Fig. 1.Individual RD piles are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole (DTH) hammer using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings shown in Fig. 2."

Jan 1, 2017

The selective placement of coal strip mine overburden is examined. Physical end chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions of similar problems. Five mining methods already used in the industry, that are capable of selectively handling; waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons arc made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided.

Jan 1, 1981

By B. W. Frazier

Jan 1, 1882