Search Documents

By T. W. Guy

DURING the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators' Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, cur-dried moistures, or oven-dried moistures. For most of the reports it was necessary to esti-mate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the. products should be meas-ured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they some-times include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture.

Jan 1, 1938

By E. DeGolyer

The problem of good engineering practice and. of good conservation practice in oil production is that of keeping gas in solution. This can best be done by producing a field as a water-drive field. Some degree of water drive is believed to be present in most fields but in the past most fields have been produced too rapidly to allow water drive to be effective. Ultimate recovery should be So per cent greater for fields produced by water drive over that from gas-expansion fields. Wide spacing will permit fields of low-degree water drive to be produced effectively as water-drive fields. INTRODUCTION NEGLECTING all the complicated scientific and technical argument that leads to the conclusion, the solution of the problem of good production practice, of good engineering practice, and of good conservation practice in oil production is to keep gas in solution. This can best be done by producing fields at a rate low enough to make effective the water drive, which exists, it is generally believed, to a degree great enough to be made effective in more than 80 per cent of the fields of the United States. Oil is being so produced in the Ten Section field of California; the Hobbs field of New Mexico; the Yates, Hastings, Friendswood, Anahuac fields and the main sand of the Conroe pool, in Texas; the Magnolia pool in Arkansas, and doubtless in many other pools. The measures of success in the efforts to achieve the solution of the problem are the maintenance of bottom-hole pressure and the prevention of an increase in gas-oil ratio. Some decline from the original bottom-hole pressure and the production of some gas are essential. A pressure gradient from the reservoir to the well is necessary and at least as much gas must be produced as that in solution in a barrel of oil. Once the optimum pressure and the gas-oil ratio have been established, they should be maintained. How common is water drive in oil and gas pools? General opinion is that some degree of water drive is almost universal. Theoretically, this conclusion appears to be a sound one. According to our present understanding of the processes of sedimentation, we would expect to find all sands or sandstone charged with connate water unless it had been displaced by some other fluid, such as fresh water percolating into the beds at the outcrop, or oil and gas, or gas only, in reservoirs. The fact that the original pressure of the fluid system in most reservoirs is approximately that of the hydrostatic head of water for the corresponding depth indicates that the sands are charged with water, and common experience in drilling into the extensions of the porous zones beyond the reservoir is to find them watercharged. The very fact that oil and gas pools have substantial pressures in their original undisturbed state indicates either that a reservoir is a rigid, closed system, a con-

Jan 1, 1941

By K. K. Kelley

This work is both a revision and an elaboration of Bureau of Mines Bulletin 371, which was published in 1934 and included data available to October 1933. During the intervening years, a large number of new experimental, high-temperature, heat-content data have become available through continuous, systematic efforts of the Pacific Experiment Station of the Bureau of Mines and the Laboratory for Inorganic and Physical Chemistry of the University of Groningen (Netherlands), coupled with various individual investigations at many institutions. In addition, calculations from spectroscopic and molecular constant data have been extended and applied to a wide variety of gaseous substances. This bulletin purposes to collect and correlate all available high-temperature heat-content and specific-heat data for inorganic sub-stances and to formulate tables and algebraic expressions for their representation. It is hoped in this manner to remove some of the tedium of thermodynamic calculations for industrial metallurgical research workers and engineers who often have available only an inadequate library in this field. It is expected also that this bulletin will have value to those teaching courses in metallurgical and chemical thermodynamics.

Jan 1, 1949

By M. Frenzel, D. Ebert, K. Bachmann, A. D. Renno, R. Möckel, J. Gutzmer, J. Krause

With the increasing demand for metalliferous and mineral raw materials and the consequent depletion of the global natural resource base, the possible utilization of secondary raw material sources is receiving more and more attention. In the present study, we present results from a detailed vanadium deportment study of three basic oxygen furnace slag (BOS) samples known to containing elevated bulk concentrations of vanadium. Complementary analytical methods that were used to quantify the abundance and composition of V-containing phases include SEM-based automated mineralogy, X-ray fluorescence analysis, and X-ray powder diffraction as well as electron probe microanalysis. The vanadium deportment was quantified using Monte-Carlo simulations of the data obtained from automated mineralogy and electron microprobe analysis. The total V concentrations identified by XRF are between 1.7 and 2.2 wt.% V. The most important hosts of vanadium are larnite-, brownmillerite- and portlandite-solid solutions. In two samples Ca carbonates also significantly contribute to the V deportment, while wuestite, lime, and native iron do not contribute significantly to the vanadium deportment. A thorough consistency check identifies considerable uncertainties in the density of the V-bearing phases as the most likely reason to explain remaining discrepancies between measured and calculated V values.

Oct 14, 2023

By Mark Colwell

As per most other earth science engineering problems, the underground coal geotechnical environment and the way in which roof and rib support interacts with the rock mass are complex issues. While the problem should not be oversimplified (i.e., the dominant failure mechanisms or critical data input parameters should not be ignored), without question judicious simplification is at the heart of all good engineering design. Engineers play a vital role in supplying the world with solutions and products; however it is crucial that engineers make practical and readily useable contributions. One way to ensure this is to employ simplification in the engineering process.

By M-d-N. Gagnon, P. Okono, Y. Bergeron

In the mining industry, decisions regarding the type and number of comminution tests to be completed typically rely on geologists? observations and conclusions when studying drill cores. Given that these decisions are based on visual observations, they are essentially approximate and often inaccurate from a comminution viewpoint, causing a sizeable margin of error in estimating characterization test needs. Consequently, companies are often forced to perform more tests than necessary, requiring a significant quantity of material, and accruing significant costs. Recently, a new device, called the Hardness Index Tester (or HIT), was developed, offering users a low cost in-house mechanism for estimating the comminution parameter A*b and the Bond Ball Mill Work Index at any mine site, with potential applications on fragments up to 25 mm from drill core. In late 2016, Agnico Eagle Mines Limited initiated a trial to investigate if having an HIT device installed in a core repository would make it possible to identify the different rock properties more accurately and determine the number and type of comminution tests required. The application of the HIT was not to replace the standard comminution tests, but rather to generate a high number of comminution and geomechanical parameters for the rock mass. Ultimately, the objective would be to determine the uniformity of the rock mass and, therefore, easily distinguish any potentially problematic zones. With this method, the appropriate number of standard tests could be determined, making the HIT not only an excellent complement to the standard laboratory tests, but also an indispensable device for a geometallurgical characterization. This paper presents the results from the HIT trial using samples from the Odyssey Project, which is a Mine Canadian Malartic property.

Jan 1, 2017

By L. Yuan, J. H. Rowland

"In 1995 and 2003, the U.S. Mine Safety and Health Administration (MSHA) conducted surveys to determine the number of atmospheric monitoring systems (AMS) that were being used in underground coal mines in the United States. The survey reports gave data for the different AMS manufacturers, the different types of equipment monitored, and the different types of gas sensors and their locations. Since the last survey in 2003, MSHA has changed the regulation requirements for early fire detection along belt haulage entries. As of Dec. 31, 2009, point-type heat sensors are prohibited for use for an early fire detection system. Instead, carbon monoxide (CO) sensors are now required. This report presents results from a new survey and examines how the regulation changes have had an impact on the use of CO sensors in underground coal mines in the United States. The locations and parameters monitored by AMS and CO systems are also discussed.IntroductionThe last survey conducted by the U.S. Mine Safety and Health Administration (MSHA) on atmospheric monitoring systems used in underground coal mines in the United States was in 2003 (Francart, 2005). A total of 146 active mines were surveyed. The survey report states that since 1995 there had been a steady increase in the use of atmospheric monitoring systems in underground coal mines as the technology of carbon monoxide (CO) sensors was improved by manufacturers. Atmospheric monitoring systems had become more reliable, and some CO sensors could be purchased with the capability to discriminate between the CO produced by a fire versus CO produced by diesel equipment. This increase in reliability had reduced the number of false alarms and the response time. The faster response time to a developing fire allowed miners to take the necessary action to put out the fire or exit the mine.At the time of the last MSHA survey, some mines still used point-type heat sensors to detect the presence of a fire on conveyor belts. This detection method works by measuring the temperature of the air around the sensor. As a fire starts to develop, smoke and hot gases are produced from the combustion process, and the air is heated up. Once the air and gases reach a designated temperature detected by the point-type heat sensor, a fire alarm signal is generated. Studies have shown that the response times for detecting the presence of a fire using CO sensors are much shorter than when using point-type heat sensors (Conti and Litton, 1995)."

Jan 2, 2018

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By L. F. Willmott

The production operation of a Kerpely gas producer at Louisiana, Mo., is described. This unit, originally designed for airblown operation was modified to permit using oxygen in the blast in place of air. The first runs J for test purposes, were made in June 1950. After this, seven production runs were made and these are the subject of this report. Total gasification time was 245 days. In each run, Nut or Pea coke or mixtures of both at a rate varying from 1,700 to 2,300 pounds per hour was converted with oxygen and saturated steam to produce synthesis gas - primarily carbon monoxide and hydrogen -approximating a predetermined rate of 80,000 to 95,000 cu. ft. per hour and a predetermined hydrogen-carbon monoxide ratio, The requirements per 1,000 std. cu. ft. of (CO + H2) were 21.6 to 30 pounds of coke, 213 to 267 std. cu. ft. of oxygen, and 3L4 to 47.B pounds of steam.

Jan 1, 1955

By Liming Yuan

Three-dimensional computational fluid dynamics (CFD) modeling is conducted to simulate spontaneous heating in a large-scale coal chamber with a forced ventilation system. Spontaneous heating is modeled as the low-temperature oxidation of coal using kinetic data obtained from previous laboratory-scale spontaneous heating studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. The water vapor transfer and the effect of heat of wetting are not modeled. The CFD model is validated by comparing simulation results with test results from U.S. Bureau of Mines experiments conducted in the coal chamber. The model predicts lower temperatures in the early stage but agrees well on the induction time for spontaneous heating. The effects of airflow rate and order of reaction on the spontaneous heating process are also examined. The calibrated CFD model is found to be useful for predicting the induction time for spontaneous heating in underground coal mines.

Jan 1, 2009

By Robert E. Wood

Engineers have known for some time that the efficiency of filtering iron ore concentrate slurry can be significantly improved by pre-heating the slurry ahead of the filters. However, heating such large quantities of dense slurry by conventional means has proven to be inefficient and high-maintenance. Recently though, submerged combustion was considered by Altos Hornos de Mexico SA (AHMSA), an integrated steel producer in the state of Coahuila, Mexico, as a means of pre-heating their iron ore concentrate. The company toured many iron ore facilities in Brasil and Labrador, reviewing their heating processes, and concluded that submerged combustion could provide a competitive advantage through operational efficiency and lower capital cost than steam boilers. Inproheat was retained by the company to design and manufacture a SubCom slurry heating system to heat 403 m3/h of iron ore concentrate slurry from 25°C to 60°C. The 60GJ/h SubCom system consists of five natural gas combustion chambers mounted in an iron ore concentrate storage tank. The system features a heat recovery unit whereby the exhaust gases are used to preheat the incoming slurry stream, giving the system an overall thermal efficiency of 95%. As a result, the steel company expects to realise significant improvements in filtering efficiency which will enable them to increase the capacity of their pelletising plant without installing additional filters.

May 1, 2010

By Norman] [Seldle

This report describes the development of a mine machinery training system from initial conception through a task and skill analysis, a training system analysis, implementation of a prototype system, and initial validation of the prototype system. The objectives of the training are to improve safety and productivity simultaneously via complete, thorough training. A task and skill analysts was executed for shuttle cars, continuous miners, cutters, loaders, face drills, tractors, and scoops. The prototype training system is for shuttle car operator training.

Jan 1, 1976

"1 INTRODUCTIONThe use of nondestructive testing (NDT) methods to evaluate the integrity of Augered Cast-in-Place (ACIP) and Drilled Displacement (DD) piles has been a subject of significant debate among engineers, contractors and NDT practitioners. This guideline document will illustrate the importance of reviewing all available information in conjunction with the NDT records. ACIP and DD piles have unique properties that must be considered when using a specific NDT method. Any evaluation of the integrity of an ACIP or DD pile must also include a thorough review of the detailed pile installation records and the site specific soil conditions. Long or theoretical descriptions of the methods have not been included in this publication. More detailed information about these NDT methods including their theoretical and historical backgrounds can be found in DFI’s Manual for Non Destructive Testing and Evaluation of Drilled Shafts (2004). Additional information can also be found in the more comprehensive textbook Nondestructive Testing of Deep Foundations by Hertlein and Davis (2006).1.1 PurposeThe intent of this guideline is to provide practical guidance for the proper interpretation of NDT results on ACIP and DD piles. Short descriptions of the main integrity methods available are provided along with several examples of how to use all of the information available to make sound engineering judgments about the results. This publication is a state-of-the-practice guideline to promote accurate engineering evaluations.For engineers inexperienced with NDT, these guidelines provide sufficient background information on NDT methods to help understand the limitations of the testing, assess the results presented to them, and formulate appropriate questions. This is particularly important for engineers charged with the responsibility to determine from those results what, if any, consequences there may be on the performance of the structure under construction."

Jan 1, 2016

By J. H. Potgieter

The method used to assess the reactivity of lime was evaluated to gauge it usefulness as a quality control tool. The effect of particle sizes, different lime and water masses for a fixed s:l ratio and the same for various s:l ratios on the reactivity values obtained, were investigated. An attempt to introduce the amount of grit produced during the slaking reaction as an additional measure of limeís quality and reactivity, proved to be unsuccessful. It was also found that the relative amount of lime slaked during the different tests was independent of the reactivity value of the lime. The investigation confirmed the usefulness of the accepted test procedure as are liable method to measure the reactivity of lime, despite various reservations expressed from a theoretical point of view.

Jan 1, 2002

By Ewan Selers, Gary Cavanough

Drilling automation technology is well advanced and automated drill rigs are in use at a number of operating mines. This is not the case for the other drill and blast processes due to significant technical challenges to overcome. These challenges, with regard to the current “on bench” practices, include placing the initiators, loading the explosive and connecting up the initiation system. Although difficult, these challenges will be solved with engineering advances.

Jan 1, 2016

By R. C. Buehl

[Improvements in refractories for high-temperature service have made possible the use of higher temperature in many processes. Consequently, it sometimes is desirable to use gases heated above 1,600° F., and for moderate rates of gas flow, there gases can be heaters best with pebble heaters. Pebble heaters of the stationary-bed type in which the chanber was lined with mullite brick and pebbles of pure alumina served as the heat-exchange medium have been used recently to heat the air blown into an experimental blast furnace4/ These pebble heaters worked well and made it possible to use air temperature up to 2,500° F. at the tuyere of the furnace. Since little has been published on this type of gas heater, a review of the construction on employed and operating data should assist in selecting applications and designing units.]

Jan 1, 1953

By F. E. Bash

IN recent years, there have been a number of experiments conducted to determine the rates of heating and cooling of various sizes and shapes of steel ingots. Up to date, however,-most of the published data has dealt with small sized ingots, the largest being an 18-in. (46 cm.) cube, the data on which was presented before the Iron and Steel Institute in May, 1918, by E. F. Law. It is due to thus lack of information on the rate at which large ingots absorb heat and come to temperature that the heating- practice varies so widely in different plants. One of the questions over which there is much debate is the proper rate of heating of large ingots for forging and the time actually required for the center of a mass of steel to come to forging temperature. As a continuation of experiments described by M. E. Leeds1 and at the request of Mr. G. R. Norton of the Sizer Forge Co. and Mr. R. C. Drinker of the Emergency Fleet Corpn., the test described in this paper was carried out on a 24-in. (61 cm.) round ingot and the rate of heating and cooling determined under regular production conditions. The ingot had been partly forged at one end but, on developing a flaw, had been scrapped so that it was available for test. The size and shape of the ingot and its position in the furnace are shown in Fig. 1.

Jan 9, 1919

By J. G. Speight

Laboratory studies indicate that autogenous heating of low-rank coal can be prevented by a prior treatment which involves immersing the coal for short (5-15 min.) periods in an inert liquid at temperatures between ~ 350° and 400°C. Such "carbonization" effectively reduces the accessible pore volume of the coal to levels at which heat generation through subsequent sorption of moisture and oxygen is too slow to cause significant temperature rises in a stockpile. In addition, this treatment also irreversibly removes most of the moisture held in the raw coal and raises its calorific value by as much as 10-12%.

Jan 1, 1973

By Morton Corn

The U. S. Federal Coal Mine Health and Safety Act of 1969 placed limits on the permissible concentration of airborne respirable coal mine dust. Evidence exists which suggests that the effects on health of respirable coal mine dust may depend on both host factors and dust properties other than concentration. Dust particle size, shape, density, specific surface area and chemical composition are among the dust parameters of interest in an epidemiological investigation of coal workers' pneumoconiosis and coal miner exposure to mine dust. The purpose of this investigation was to develop and demonstrate the feasibility of techniques to determine selected properties of respirable coal mine dust. An approved underground horizontal elutriator which samples air at 36 cfm was designed, fabricated and utilized in this study to collect respirable coal mine dust in three mines representing the Pittsburgh, Lower Freeport and Lower Kittanning coal seams. Analytical procedures for measurement of respirable dust sample particle size, density, random projected area, total surface area and chemical composition are presented. Results of analyses of three samples collected in each mine are presented. Up to five full work shifts of sampling were required to accumulate approximately five grams of respirable coal mine dust in each sample. Statistical tests were applied to determine the significance of differences between properties of dust samples collected in the same mine and between arithmetic mean values of dust properties representing three samples collected in each mine. A comparison was also made between

Jan 1, 1972