Search Documents

By J. E. Chilton

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro-chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1-to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light-emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 2010

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed. Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By J Deraisme, P Epinoux, O Bertoli

"Société le Nickel exploits the Dôme lateritic nickel orebody at its Tiébaghi operations in New Caledonia. The site geology has an obvious bearing on recovery and metallurgical performance, with controls that are extremely complex at all scales, including lithology, oxydo-reduction conditions, mineralogy and multivariate geochemistry. In this context, establishing an adapted recoverable resource estimation method that is efficient and transparent proves an interesting challenge. The method must address the key notions of: support effect – the exploration data set can only warrant the estimation of large panels of 20 × 20 × 3 m3 that are much larger than the selective mining units (SMUs) of 5 × 5 × 3 m3 information effect – the selection at the production stage uses estimates based on information that is much denser than that available for mine planning.The problem is rendered more complex in this type of deposit by the fact that the additive variables used for the estimation (metal accumulation and ore tonnage) are not the ones used to establish the selection at the mining stage (ie the nickel grade of SMUs, which is the ratio of accumulation on tonnage). Eventually, the selection criteria not only involve Ni grades, but also other elements such as Al2O3, Fe2O3, MgO and SiO2.The solution presented in this paper is to construct an SMU multivariate simulation in the saprolitic horizon and construct an efficient post-processing aimed at producing multivariate recoverable resource estimates. The efficiency constraints imposed by the number of blocks to be simulated (1.5 million) lead to resorting to direct block simulations. The underlying multivariate discrete Gaussian model, which had its validity tested beforehand, is put to good use to mimic the selection process that happens at the mining stage by offering the ability to simulate a composite value located at random within each block.The paper also presents the application of a scenario reduction algorithm to pick a representative subset of a few simulations to help appraise the risk attached to the downstream (reserve optimisation and mine sequencing) phases of the project. The original version of the paper (see Deraisme, Bertoli and Epinoux, 2014) used an early version of the scenario reduction plug-in (named S2RM) built in Isatis® software, where measuring the distance between the initial set of scenarios and the reduced set was based on Ni only. The implementation presented here is for the second generation of S2RM, where measuring the distance between the initial and the reduced set of realisations is based on all study variables. The benefits of the measure adapted to the true multivariate nature of the problem are highlighted in this updated version of the paper.CITATION:Bertoli, O, Deraisme, J and Epinoux, P, 2014. Multivariate block simulations of a lateritic-type nickel deposit and post-processing of a representative subset, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 99–108 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By T Mattiske

The Fimiston Open Pit (commonly referred to as the æSuper PitÆ) is a part of the Kalgoorlie Consolidated Gold Mines Pty Ltd (KCGM) operation in Kalgoorlie-Boulder. KCGM manages the Fimiston Open Pit, the Mt Charlotte underground mine, the Fimiston Mill and the Gidji Roaster for its Joint Venture Owners, Newmont and Barrick Australia. KCGM produces up to 850 000 ounces of gold per year. The KCGM operations are located on the historical Golden Mile on the outskirts of the City of Kalgoorlie-Boulder, about 600 kilometres east of Perth Western Australia. This traditionally underground mining centre has been worked since 1893, yielding in excess of 50 Moz of gold from ore with an average head grade of 10 g/t. This represents approximately ten per cent of the gold produced in Australia and one per cent of the gold produced in the world. The Fimiston Open Pit is essentially an aggregation of what were known as the Judd, South, Paringa, Croesus/Eclipse, Central, Brownhill, Drysdale, Morrison, North and Horseshoe pits into one continuous large-scale operation. The old Fimiston Underground Operations (included the Main, Croesus, Chaffers, Lake View, and Perseverance shafts) were also located within the area of the Fimiston Open Pit. The underground operations closed in 1992 due to high mining costs.

Jan 1, 2002

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed, Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By Keith Heasley

This paper is a retrospective on the development, application, and enhancement of the LaModel program from a personal perspective. The narrative starts with an explanation of the objectives behind the original development of the program and then introduces some of the unique and very practical features of the program. Next, a demonstration of how LaModel was advantageously used to model stresses and displacements in a multiple-seam mining situation with highly variable topography is presented. This is followed by the details of a number of the major enhancements and expansions of the program over the years. A back-analysis of the Crandall Canyon Mine collapse is then briefly presented, along with the associated development of a recommended calibration procedure for the critical input parameters to LaModel. Finally, some of the present research areas are briefly described, and future enhancements are introduced.

Jan 1, 2011

Newcrest Mining Limited (NML) owns and manages the Ridgeway Gold Mine (RGM) located outside Orange in the state of New South Wales. RGM is a new underground sublevel caving (SLC) operation that is ramping up production to 4 Mtpa. The success of the SLC method at RGM is strongly influenced by production drill and blast practices. Distinguishing features of the Ridgeway SLC operation include choke blasting against broken rock, drawpoint brow preservation, loading of blastholes with different in-hole bulk emulsion densities, precharging of production rings and routine drawpoint fragmentation assessment. These areas are described in the context of RGMÆs required blasting objectives, production drilling and charging activities and innovative practices.

Jan 1, 2002

Subsurface development requires some geotechnical conditions and challenges. Most of then are related to the compatibility between tunnelling system and surrounded ground conditions, and design criteria. Design criteria usually involve lining pressure and ground control of displacements. In order to fulfil these requirements, geotechnical parameters have to be obtained as well as construction aspects have to be taken into account for predicting the tunnel behaviour. The Brasilia Metro is presented as a case history illustrating the geotechnical conditions and challenges for its implementation. It is 42 km long, including tunnels excavated in collapsible porous soils by the New Austrian Tunnelling Method. The Brasilia porous clay presents some characteristics, which may lead to large deformations due to structural collapse. Empirical methods were calibrated for collapsible porous soils and then applied to predict tunnelling-induced settlements. Settlements due to soil structural collapse modify completely the expected settlement profile, increasing their values from the tunnel crown to the ground surface. Consequently, surface settlement trough volumes were also greater than the ground losses around the tunnel. In this case history, structural collapse of porous soils played an important role and must have been taken into account to predict correctly the settlement trough and profile. Numerical simulation has shown that settlement magnitudes due to structural collapse are strongly dependent on the soil stiffness reduction after collapse and the extent of the collapsible zone.

Jan 1, 1999

By Marcelo de Oliveira, Antoine Allanore, Dennis P. Chen, Davide Ciceri

Potassium fertilizers (potash) are mined in a handful of countries in the Northern Hemisphere. Potash is either expensive or unavailable to the farmers of the Southern Hemisphere. Alkaline alteration of K-feldspar rock (ultrapotassic syenite) in autoclave in the presence of Ca2+ generates a mixture of K-bearing calcium-aluminum-silicate-hydrate (C-A-S-H) minerals that potentially can be used as an alternative local fertilizer. This work investigates the effect of processing temperature (200 °C, 220 °C, and 230 °C) and time (from 0.5 to 3.0 h) on pH, mineralogy, and elemental availability of the C-A-S-H mineral mixture. Increasing temperature results in an increased conversion of K-feldspar and increased content of both the mineral tobermorite (Ca5Si6O16(OH)2·4H2O) and amorphous phase in the resulting C-A-S-H mixture; increasing time results in an increased conversion of α-dicalcium silicate hydrate into tobermorite. The amount of K leached from the mixture is relatively constant across all processing conditions. Hydrothermal alteration in autoclave of K-feldspar-bearing rocks such as ultrapotassic syenite permits the synthesis of a potential potassium fertilizer which alkalinity and mineralogy can be tailored according to soil requirements.

May 22, 2020

By V. Jovicic, J. Likar

The knowledge of the geological sequence and hydrological conditions in the area of portals was the basis for the design of the entry of the highway into tunnel Trojane. Mudstone, claystone and sandstone dominate the rock layering, which is tectonically reworked and contains structural anomalies. The complexity of the sequence makes it impossible to survey all the relevant features along the full 3km length of the tunnel. Sudden and frequent transitions between litological sequences impose potential instabilities and make the excavation of the tunnel particularly difficult. The initial survey established the zones of potential failures. These were monitored using topographic survey and inclinometers with an aim to make further geotechnical analyses more reliable and adjusted to the ground conditions. The analyses of the wall construction and the results of the monitoring showed that the design of the retaining wall was adequate. La connaissance de la séquence géologique et des conditions hydrologiques dans l'aire des portails a été la base pour la planification de l'entrée de l'autoroute dans le tunnel Trojane. Le schiste, l'argilite et le grès dominent la couche rocheuse qui est tectoniquement transformée et contient les anomalies structurales. A cause de la complexité de la séquence, il est impossible de revoir toutes les particularités le long des 3 kilomètres de la toute longueur du tunnel. Les transitions soudaines et fréquentes entre les séquences lithologiques imposent l'instabilité potentielle et font l'excavation du tunnel particulièrement difficile. La revue initiale a été établie sur les zones où il existe l'éboulement potential. Elles étaient contrôlées à l'aide de la revue topographique et de l'inclinomètre pour que les analyses géotechniques suivantes soient plus sûres et adaptées aux conditions du sol. Les analyses de la construction des murs et des résultats du contrôle ont montré que la planification du mur réteneur était correspondante. Der Autobahneingang in den Trojane Tunnel war projektiert auf Basis von der Kenntnis der geologischen und hydrogeologischen Bedingungen in dem Portalgebiet. Das Gebiet besteht aus dem Tonstein und dem Sandstein. Die Schichten sind tektonisch verformt und sind deswegen sehr heterogen. Die anfaenglichen Untersuchungen haben die Zonen von den potentiellen Bruechen definiert. Weitere geotechnische Analysen waren fitted an reale geologische Bedingungen durch das Monitoring der potentiellen Bruchzonen, welches aus den topographyschen Messungen und Inklinometerdaten entstand. Die Analyse des Wandbaues und die Resultate von dem Monitoring haben erwiesen, dass die Wandprojektierung entsprechend war.

Jan 1, 2003

By E. Pourjenaei, P. Ghobadi

High Pressure Grinding Roll (HPGR) is efficient equipment in comminution process. HPGR could be a good option for preparing ball mill feed at the first stage of grinding due to its high efficiency and low energy consumption. Closing with a screen, these mills are utilizing as one of the principle parts in mineral processing industries, especially for iron ores. Recently, HPGRs are working as primary mills at 4 developing lines in Gol-e-Gohar Iron Ore Processing Complex, Iran. Different mechanism of particle crushing in compare to the other tumbling mills makes the HPGR as certain equipment with its own particular controlling parameters. Hydraulic pressure, roller speed and level of material inside feeding hopper are the most important variables influencing grinding efficiency of the HPGR. To figure out how they impress the process and operation situation, different industrial tests were carried out and the best result (d80 about 8 mm for HPGR discharge) was achieved at 180-190 bar pressure (P), 300 rpm speed (S) and 50% of hopper level (L). It is worth noting that this finding has been observed through past pilot test too. We also used design expert method (DX7 software) to develop the best design and analysis the test results, as well. According to the mechanical restriction of HPGR and process limitation in the plant (based on the industrial results), we adjusted value of each parameter in a logical range. Therefore, 20 industrial tests were conducted, as DX7 recommended, and the various impacts of the parameters and their interaction were identified based on statistical analysis. As the authors expected, it was revealed that after presser, roller speed is a critical variable because of its significant role in residence time of the particles between the rollers. The function below has been determined to explain the relation between different parameters and the response.

Jan 1, 2018

By K Muller, T Oosthuizen

Blast exclusion zones are instrumental in protecting equipment and personnel. When there is no constraint in footprint, the exclusion zone can be enormous, practically eliminating the hazard of flyrock. Unfortunately, this may not always be the case and in many circumstances the blast design needs to be altered to suite such scenarios. When a conservative design approach is taken, it could completely eliminate any form of ejection, whether it is from the free face or the bench itself. The degree to which typical flyrock models describe fragment motion through air with ballistic flight equations are not justified when such a high level of control is applied. This paper examines various methods of risk analysis and suggests an approach to be used for controlled blasting.The outcome of principles discussed in this paper can be seen in video form (Mavmedia, 2014).CITATION:Muller, K and Oosthuizen, T, 2015. Should the blast exclusion zone be based on a qualitative or quantitative analysis? A practical implementation conundrum, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 425–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By B. L. Bessinger

Because of a, work stoppage at the Carlsbad plant, IMC faced the challenge of operating a 24-hour-a-day mine and plant with inexperienced maintenance and production crews. This is an underground mining operation, using the room-and-pillar mining- method. The mine was entirely, mechanized with conventional equipment, was hoisting an average of 13,539 tons off ore per 24 hours, and employed a, mine maintenance group of 100 men. The 100-man, mine maintenance group was equally divided between mechanics and electricians. In re-forming this maintenance group, two main objectives were to be achieved (1) a general upgrading off the intelligence level; and (2) the elimination of craft lines for greater flexibility.

Jan 1, 1966

By Heng Yi

The salt lake brines that lithium is extracted from have high chloride levels making the brine very corrosive to stainless steel extraction column internals. This is a significant problem in column scale-up to industrial production. Two types of corrosion-resistant ceramic internals, the hybrid ceramic internal and ceramic plate, were designed and tested under pilot conditions for future industrial application in this field. The hydrodynamic results (Yi et al. Ind Eng Chem Res 56 (4):999–1007 (2016), [1]) show that holdup of hybrid ceramic internal is higher than that of ceramic plate by around 50%, while Sauter mean diameter when using the hybrid ceramic internal is smaller than when using the ceramic plate by around 30%. This results in a larger mass transfer area, hence better mass transfer efficiency for the hybrid ceramic internal. Axial dispersion and mass transfer parameters are also examined (Yi et al. Ind Eng Chem Res 56(11):2049–3058 (2017), [2]). The results show that the column with hybrid ceramic internals has 50% lower axial dispersion coefficient and 50% higher mass transfer coefficient, leading to higher mass transfer efficiency. The transfer unit height of the column using hybrid ceramic internals can be as low as 0.2 m, showing very good efficiency. This is promising for near-future applications. Two-phase computational fluid dynamics (CFD) models have been developed for the two columns with ANSYS FLUENT commercial software. CFD successfully predicts the higher holdup and lower axial dispersion coefficients for the hybrid sieve plate pulsed column as measured in the experiments, and the cause for the difference in performance has been explained with information from CFD.

By R. W. Van Dolah

An important function of stemming used to confine explosives in shot holes in underground coal mines is to minimize the chance of ignition of firedamp or coal dust by the detonation products. Until 1952, the Bureau of Mines approved only the use of fireclay or similar incombustible material for stemming permissible explosives. At least 2 feet of stemming were required except in holes less than 4 feet deep; in such short holes the stemming was required to be half the depth of the hole. Over the years, several special stemming devices have been proposed in the United States as substitutes for fireclay. Many economic and safety advantages were claimed for these devices, but only one approved device has been marketed in this country. Bureau requirements for stemming explosives in coal mines were modified at that time to permit the approved stemming device to be used as a substitute for the required fireclay.

Jan 1, 1961

By Igor Kuzymin, Isaak Maximov, Iuriy Akkerman, Galina Aksenova, Valentina Sentemova, Nataliya Trubechkova

"The Russian Federation possesses large reserves of oxidized ferruginous quartzites. These ores are currently mined together with magnetite ores and are stockpiled on account of unavailability of an efficient processing technology. This paper presents the results of investigations performed on the ores from the largest oxidized ferruginous quartzite deposit located in the Kursk Region iron-ore basin of Russia. The objective is to produce concentrate with iron content at least 66% and silica content within 5%. A processing technology was, developed under laboratory conditions, which included ore preparation, wet magnetic separation in weak and strong fields and reverse cationic flotation with addition of caustic soda, dextrin and Lilaflot 811M (alkoxy propylamine) collector from Akzo Nobel. The developed technology produced iron recovery concentrate with iron content of nearly 67%, and that of silica - 4.1%, iron recovery into concentrate being 72.6%."

Jan 1, 2014

By Minjun Tang, Jianfeng Zhou, Feng Chen, Linjiang Qing, Xiaolei Song, Yufeng Guo, Tao Jiang

"Reduction swellability index (Rsn and low temperature reduction disintegration index (RDI) of vanadium-titanium magnetite oxidized pellets are harmful to the processing of ironmaking, for example, causing serious gas permeability, decreased yield, higher coke ratio and more furnace dust. Thus, the improvements of RSI and RDI of vanadium-titanium magnetite oxidized pellets were investigated in this paper, including the pretreatment of raw material, additives of dolomite or boric acid, pellets treated in chloride solution and so on. The results showed that damp milling as pretreatment and boric acid added in pelletizing were conducive to the RSI which decreased 5% and 7% respectively, while they were not efficient enough in improving RDI. Dolomite was efficient in improving RSI, but had negative effect on RDI. There was no evidence to show that RSI and RDI would be improved when pellets were treated in chloride solution. Pursuing this further, the mechanism of those improvements were investigated.IntroductionIn the world, vanadium-titanium magnetite utilization is investigated around how to recover iron, titanium, vanadium, and divided into blast-furnace method and non-blast-furnace method according to respective characteristics. Blast furnace method [1, 2] can recover iron and vanadium effectively, but Ti02 cannot be recycled. Non-blast-furnace methods include rotary kiln-electric furnace method, pre-reduction electric furnace method, reduction- grinding method and sodium vanadium-rotary kiln-electric furnace method and so on. [3-7]Comparing to the Non-blast-furnace method, the method of blast furnace smelting has been put into industrial applications. And it has the following advantages: First of all, effective recycling iron and vanadium; Second, technical problems of high titanium slag in blast furnace smelting; Third, it has mature technology in blast furnace smelting."

Jan 1, 2013

By Megha Patel

"The objective of this project was to investigate the application of Prompt Gamma Neutron Activation Analysis (PGNAA) technology to provide real-time on-belt elemental analysis of feed ore in base metal sulphide processing, in this case at the Mount Isa Mines Zinc-Lead Concentrator Heavy Medium Plant (HMP). After initial exploratory testwork proved successful, a Geoscan On-Belt Elemental Analyser was retrofitted onto the existing HMP feed conveyor. Dynamic calibration of the Geoscan was conducted based on laboratory XRF analysis results of the HMP feed conveyor hammer autosampler samples from May to November 2013. Comparison of the Geoscan results to the laboratory XRF analysis results during and after dynamic calibration indicated the technology had acceptable accuracy to be incorporated into HMP process control. The variation between the two sets of data includes all primary sampling, sample preparation and XRF analysis errors as well as the Geoscan errors themselves. The Geoscan instrument precision must be calculated separately through a duplicate sampling campaign and independent laboratory analysis before extending the scope of its range of application beyond HMP process control. The expected benefits of integrating the Geoscan real-time data into HMP process control are optimised HMP metal recovery, improved cost efficiency and improved stability of the downstream processes (milling and flotation). Utilisation of the Geoscan will also enable improved feedback to mines on grade control and dilution, and provide additional information on individual ore types when fed as campaigns to HMP."

Jan 1, 2014

By A Golsby

Both primary and secondary ventilation is important in underground mining. Secondary ventilation refers to the provision of ventilation to development ends, stopes and services facilities, which constitute secondary circuits tapped off the primary circuit or main through flow of air.An unbalanced primary and secondary combination can cause re-circulation, which is inefficient and potentially hazardous. These inefficiencies extend into operational and other considerations, such as power.Most cost justification analysis covers capital and physical consumables. These analyses are often not comprehensive or holistic. This case study is an example of ‘how to holistically justify’ a secondary ventilation circuit and optimise it to meet all stakeholder needs.This paper particularly addresses the following:how to account for all stakeholders in a secondary ventilation cost justificationthe secondary ventilation componentsthe cost justification outcomes and how to measure themsome of the sensitivitiesthe stakeholdershow to present the justification to meet the stakeholder needssecondary ventilation cost justification.CITATION:Golsby, A, 2015. Secondary ventilation as a value proposition – a case study, in Proceedings The Australian Mine Ventilation Conference, pp 49–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D Hope, D Mitchell, B Metcalfe

In recent years there has been a major change among mining companies in their mining methods. This has been driven by the need to increase shareholder value and optimising the value from an operation. With this understanding there has been a need for all producers to become more efficient in their mining processes. An analysis of the coal losses at Mount Thorley Operations indicated that the major losses were in the dragline section of the mine due to coal damage from throw blasting. This damage was evident after the removal of the overburden by the dragline.Coal and Allied Mount Thorley Mine in partnership with Orica Explosives developed a process to reduce the coal loss associated with the throw blasting of Mt Thorley. Orica provided its specialised knowledge and experience in the drilling and blasting area and combined this with the local mining knowledge and expertise of Mount Thorley Operations personnel to conduct the project. This partnership reduced coal loss in excess of 50 per cent whilst maintaining targeted dragline productivity.

Jan 1, 2001