Search Documents

By I. Gombköto

To sustain the growth of industrial production necessitates the increasing of the amount of processed mined raw and secondary materials. As a side effect of raw material production, the amount of tailings material, - coming from mineral processing operations ? increases as well. Using wet technology, these tailing materials are generally transported and stored with the water used for previous operations. This habit could lead to dangerous situations. Enough to remember the disasters had happened to the last decade, safe tailings operations need to remove as much water from the solid as possible. Environmental, technical and economical needs should meet, therefore using a technology combining these specific needs could be necessary. Paste technology was introduced generally into tailings operations at the last ten years, as an answer to the call of the above mentioned challenges, however there are still many questions to answer within the frame of using it. The Institute of Raw Materials Processing and Environmental Process Engineering of the University of Miskolc has been dealing with mechanical process engineering, especially by the support of the EU project TAILSAFE Contract nº EVG1-CT-2002-0066 and the NKFP 3A/068/2004 Hungarian fund extensive research has been carried out about paste technology. Different test methods and materials were applied. Tested tailings materials were as follows: different fly ashes from coal power plants from Pécs ? Hungary, Gyöngyös ? Hungary, Neyvil ? India, different Croatian ashes, hazardous waste incineration plant ashes from Dorog ? Hungary, different kind of sands from Hungary, fine glass sand from Fehérvárcsúrgó ? Hungary, flotation ore processing tailing from Gyöngyösoroszi ? Hungary. Different additives, as gypsum, bentonite and cement were tested as well. The applied test methods were as follows: physical material testing (laser sizer, piknometer, different microscopes), X-ray diffraction analysis, settling columns, the three measuring pipes tube viscometer (16~27 mm pipe diameter), a hydraulic test loop with different pumps (40~53 mm pipe diameter, 0.2~4 m/s average slurry velocity range, 0%~52 % volumetric concentration range), rotational viscometer, Cassagrande yield locus tester and the slump cone test. This paper summarizes and systematizes the results of the aforementioned research as well as reports about the developed paste pipe transport design method based on the fine suspension ? coarse mixture model. The paper also reports about a systematic experimental series with different materials to establish criteria when high concentration suspensions behave like paste.

Jan 1, 2014

By F. Dakubo

"Solvent extraction of copper pregnant solution (PLS) obtained from ammonium peroxodisulfate assisted leach was modeled using response surface methodology. Mixing speed, pH, reagent concentration and organic to aqueous (O/A) ratio were selected for testing. A pitched blade mixer was used in the experiment. Mixer speed contributed significantly to copper extraction significant, while pH had minimal effect on copper extraction. The response model developed has an R2 = 0.97 and Adeq precision of 28.3. A parallel kinetic comparing study using a straight blade Rushton turbine in a turbulent regime of mixing showed no difference (p-value =0.308) between peroxodisulfate assisted leach PLS and conventional ferric/sulfuric acid leach PLS- the power draw data support this conclusion. INTRODUCTION High arsenic chalcopyrite concentrates are a problem to the smelters all over the world due to high arsenic gas emissions during smelting. Therefore leaching is often the alternative for extracting the copper in these concentrates if dilution with low arsenic concentrate is not possible. High-pressure autoclave leaching is used. Alternatively, the use of stronger oxidants such as peroxodisulfate has been proposed [16, 18]. There is a concern brought up by the hydrometallurgy community about the faith of the organic extracting reagent coming into contact with stronger oxidant residue in the pregnant leach solution (PLS) and hence the efficiency of such extraction process. This work, therefore, looks to answer such concerns. PLS generated from leaching of chalcopyrite concentrate with the peroxodisulfate ion was used in this solvent extraction experiment. As a liquid-liquid extraction, solvent extraction involves contacting the aqueous PLS with organic extractant via mixing. Mixing is known to increase the interfacial area for mass transfer by decreasing the diffusion path length (Jussi et al.1997). EXPERIMENT Instruments and Reagents Reagent grade Acorga 5910 reagent was used in the experiment was supplied by Cytec (Current name Solvay), Ammonium peroxodisulfate and sulfuric acid were reagent grade obtained from Amazon. Apparatus The solvent extraction tests were carried in a 2000 ml plastic cylindrical reactor equipped with four 0.5” baffles. In the hypothesis test, the reactor was a 4000 ml cylindrical reactor with four 1” thick baffles arranged evening in the reactor. Comparison between peroxodisulfate and ferric leach PLS via hypothesis test"

Jan 1, 2018

This paper describes techniques that have been used at RixÆs Creek Colliery to control blast vibration from throwblasts that face a residential area 4 km in front of the face. The paper describes blast design, face control including laser profiling, selective loading of blastholes after borehole camera surveys, and techniques used to assess the effect of burden variation, the cumulative effect of drilling and delay sequence, and the effects of meteorology.

Jan 1, 2001

By X. H. Li, F. Xie, Q. Zhang, Z. H. Shen, S. Mao

"There is abundant rare-earth element(REE) in our country, but it is very fragmented in the earth's crust, and it is very difficult to mining or mining cost is extremely high. There are few of industrial value rare-earth deposits. There is a lot of concomitant rare-earth deposits, and the comprehensive utilization value is high. There is very rich carlin-type gold resource, associated with a certain amount of REE in the southwest of Guizhou province. In order toutilize comprehensively the resources, this paper conducts the study on the occurrence characteristics of REE in the ore. By the chemical analysis, the gold grade is 3.35g/t, the organic carbon 0.81%, the total REE 0.022%, which is a high carbon fine disseminated gold ore. By the optical microscope and XRD analysis, the major minerals are quartz, pyrite, calcite, limonite, arsenopyrite, mica, kaolinite, clay minerals, etc. In addition, there is a large amount of carbonaceous materials, such as organic carbon, graphite, which is harmful on leaching of gold. By the scanning electron microscopy analysis, there are thorium, lanthanum and neodymium, ytterbium, persimmon and other REE in the ore. Gravity separation shows that REE could be enriched to lighter material mainly, which indicates that REE disseminate closely with lighter materials.INTRODUCTION Carlin-type gold ore is important gold resource in the world, which are mainly distributed in Nevada and its vicinity, as well as the two Golden Triangle of Yunnan, Guizhou, Guangxi and Sichuan, Shanxi, Gansu province in China(Su W.C. et al.,2009; Xia G.X.,1996).Guizhou carlin-type gold ore is the second largest gold resource in the world(Muntean J L et al.,2011), distributing along the southwestern margin of the Yangtze plate, mainly mineralizing in the neopaleozoic-early mesozoic(Xie Z J et al.,2017). Many large gold deposits have been found in southwest in Guizhou in twentieth century, such as Zimuyou,Getang, Lannigou, Shuiyindong and Laowanchang gold deposit, and so on, and the gold reserves reach over 100 tons(Xia Y. et al.,2009).There is a certain amount of rare-earth resource in the carlin-type gold ore in the southwest in Guizhou province, and the current researches might mainly focus on characteristics of REE from the angle of geological mineralization(AnanyevY.,2015), not from the angle of separation and enrichment."

Jan 1, 2018

By Emery Chilton, Charles Taylor, Mark Senk, Linda McWilliams

Three-axis ultrasonic anemometers are used to study airflow in the NIOSH ventilation gallery where ventilation in an underground mine is simulated. In this study, performance characteristics of this anemometer are evaluated and the effects of sensor orientation and sampler location on flow readings are examined. The study results provide guidelines for more effective use of the ultrasonic anemometers in the ventilation gallery.

By Nur Hossain

Analysis of Linear Elastic Fracture Mechanics (LEFM) parameters via the Virtual Crack Closure Technique (VCCT) has been obtained for SENT specimens of AM6OB magnesium alloy. It is found that the ratio of initial crack length to initial monotonic plastic zone size is one of the critical factors in establishing the limit of using LEFM concepts. If this ratio is below a certain limit (i.e. when crack lengths are small in comparison to the plastic zone size), loss of similitude stress intensity factor range would occur. This ratio, therefore describes the limit below which the use of LEFM would no longer be admissible. In this study, the above limit was established for AM6OB magnesium alloy. In addition, fatigue crack propagation tests were conducted to ascertain the fatigue response of the alloy and determination of the coefficients of Paris model.

Jan 1, 2010

By C. L. Popp

The scope is to address issues confronted by parties in the mining industry such as: Mine planners, survey and engineering departments, field teams and subcontractors. Describing approaches and best practices for assembling a project team to identify and create modeling requirements and to implement beneficial results. 3D Machine Control and Guidance tools continue to reduce project risk and attract quality resources with skill sets new to the earthmoving industry. These tools increase production, reduce rework and help with government permitting.

May 1, 2013

By A. E. Torma

In recent years the copper industry has gained considerable economic stability. An essential part of this industrial wealth is attributable to the successful application of bio-mediated heap and dump leaching techniques in the recovery of copper from low-grade resources. This study evaluated the leachability of a chalcopyrite conlentrate using naturally occurring mixed culture of predominantly Thiobacillusferrooxidans and Thiobacillus thiooxidans. For the effects-of pulp density, the overall reaction rate constant (k) and the order of reaction (n) have been determined to be 1.93 h-1 and 1.36, respectively. Cyclic voltammetric measurements revealed that intermediate reactions are involved in the chalcopyrite oxidation. Using the Price approach, it was shown that the dissolution of chalcopyrite is solid state diffusion controlled.

Jan 1, 1992

By J. P. Thomson

Magnesium alloys are steadily improving their market share as structural components especially in the transportation sector. Therefore, there is a great deal of interest from the automotive and the metal casting industry to develop viable economic casting processes for magnesium-base alloys. This paper summarizes the preliminary results on the continuing projects within CANMET-MTL on casting processes such as gravity and low-pressure casting in sand molds, permanent molds and lost foam.

Jan 1, 2004

By Rouzbeh Afsharhasani, Moses Karakouzian, Brandon Kluzniak

"The Vegas High Roller is the centerpiece of a new development parcel adjacent to the Las Vegas Strip. At a height of 550 feet, the High Roller is currently the tallest observation wheel in the world. The design team conducted a geotechnical site investigation to characterize the alluvial soils and cemented layers encountered and to provide foundation design recommendations for the observation wheel, boarding platform, and temporary structures needed to erect the wheel structure. This paper presents a case history of the geotechnical design process, including development of a ground model and design parameters, high-strain dynamic axial load tests, and settlement monitoring during construction. Results indicated that design parameters were conservatively assumed and that the majority of the axial load was transferred to a near surface caliche layer, thereby resulting in insignificant settlement of the foundation system.IntroductionThe engineering of the Vegas High Roller is similar in concept to that of the London Eye and the Singapore Flyer. The wheel has 28 cabins, each with a capacity of 40 persons. The top point of the structure is 550 ft above ground level at the site.A geotechnical site investigation program was undertaken and subsequent analyses were performed to provide foundation recommendations for the observation wheel legs, boarding platform columns, and temporary structures directly associated with construction of the observation wheel."

Jan 1, 2017

By L. A. Nazarova, M. Vandamme, L. A. Nazarov, R. I. Rodin

"The paper describes a new method of interpreting the “canister test” data for the quantitative estimation of gas-kinetic parameters of coal bed based on the developed model of gas emission from coal sample placed in a sealed container. The model accounts for grain-size composition of the sample, initial gas content S, as well as coefficients of diffusion D and mass transfer ?. The inverse coefficient problem is formulated to find S, D and ??from the data of pressure measurements in the sealed container. It is shown that the inverse problem is uniquely solvable if the pressure is dropped during the experiment. The method has been tested using the data from an underground coal mine in the Kuznetsk Basin.Based on the poroelastic model of a coal bed and Khristianovich’s concept about origination and evolution of the filtration zone F in the neighborhood of a degassing borehole the authors considered the corresponding direct problem on rock mass geomechanical state. It was offered interpretation method for data on pressure measurements in a plugged degassing borehole allows evaluation of the diffusion coefficient, the horizontal component of natural stress field and parameters of F. The related inverse problem of the mixed type is formulated, and the cost function is constructed. The analysis using synthetic input data has shown that the cost function has a number of local minimums arranged on the same straight line, one of the minimums being the inverse problem solution. INTRODUCTIONPre-mine degassing is an integral part of coal mining. It allows mitigation of induced accidents in mines (coal and gas outbursts, rock bursts) (Guide, 1990; Malyshev & Airuni, 1999; Seidle, 2011) and also furnishes an alternative and ecology-friendly energy source—methane (Rice, 1997; Nambo, 2001). Choosing an optimized pattern of degassing boreholes, as well as estimating degassing time and amount of gas recovered requires data on gas-kinetics indices of coal beds out of which the key parameter is a gas content S. According to the latest guidelines for coal mines in Russia (Ruban et al, 2012), mining is allowed if S in a coal bed section is under 7 kg/m3."

Jan 1, 2015

By M. A. Bartkoski

Today?s surviving companies are being pushed to a heightened level of excellence due to market changes. Therefore, new business strategies must be explored. This paper offers a sequenced plan to retool, empower, and organize the entire team for a common goal. Integrity Process is an operating system that is very comprehensive and is integrated in every part of the business. It relies on a detailed prevention concept intertwined with accountability that produces individual efficiencies and team effectiveness. Integrity Process focuses on the importance between working from commitment motives versus compliance fears. The results are balanced in priority and truly yield a win-win for the owners, management, workforce, and the community. Integrity Process can and is being used in any industry that is challenged to optimize the relationship between people and process.

Feb 23, 2014

By S Talu, E Savage, S Howe

Major falls of ground, strainbursts, airblast and mudrush events are the major hazards in block caving environments, resulting in both safety and financial consequences and losses. Rio Tinto mines have developed strategies to reduce the likelihood of these events occurring. However, until recently, there have been no tools available to monitor and manage these hazards in real time.Mira Geoscience and Rio Tinto have collaborated to develop real-time geohazmaps to monitor and manage major cave hazards. These geohazmaps are used by mine planners to integrate multiple hazard parameters that contribute to form a combined hazard rating.The benefits of implementing geohazmaps include safety and cost improvements through the early identification of potential locations for major events. These cost savings are realised in the design phase, where development and critical infrastructure is located in areas of lower hazard rating. Additional improvements can be achieved by taking the hazard level into consideration when planning the production and development schedules and ground support design.CITATION:Talu, S, Savage, E and Howe, S, 2016. Geohazmap implementation in block cave mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 817–822 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A. Anani

The goal of hot mix asphalt (HMA) design is optimal material blending to meet Superpave specifications. HMA cost minimization has being modeled as linear programing (LP) (Awuah-Offei et al 2011) and mixed integer LP problems (Brown et al, 2012) and solved with commercial software such as LINDO and CPLEX. Often these software, which are designed to solve general optimization problems, have licenses that cost thousands of dollars. The objective of this study is to develop a novel solution algorithm to the HMA optimization problem presented by Brown et al. (2012), which will negate the need for expensive commercial packages and is specific to this problem. This novel algorithm is based on the branch and bound algorithm for solving mixed integer problems. The algorithm is incorporated into a software package with an easy-to-use graphical user interface. The developed algorithm is validated using a real-life HMA problem. Using this solution algorithm will save companies thousands of dollars, otherwise used to purchase software licenses.

Feb 23, 2014

By Atul Kurnar

In the present research a two-cell polymer electrolyte membrane fuel cell stack (PEMFCS) with SS-316 bipolar plates has been tested. Different flow field designs were studied and a modified multi-parallel channel design is proposed. The stack is stable within ±3 mV even after 1000 hours of continuous operation, indicating efficient water management and effective removal of any metal ions from the stack. Also no iron is detected in membrane electrode assembly (MEA) by EDAX analysis after 1000 hours of cell operation. Results indicate that high operating pressures beyond 138 kPa didn't significantly increase the performance of cell, however added much to the pressurization cost of the system. Tests at different temperatures showed that at temperatures below 80°C, external humidification could be completely removed. The prototype stack is also tested under variable load conditions simulating highway-driving schedule. The experimental efficiency of PEMFCS is 48%, which is in good agreement with the model predicted efficiency of 53.8 %. Results show that 59% of the total losses are due to ohmic polarization in the cell. Further analysis on applications of the stack in automotive transportation system is in progress.

Jan 1, 2002

By O Arafat, R E. McIvor, K M. Bartholomew

It is well known in the industry that good classification system performance is vital to efficient ball mill circuit performance. But what is meant by good classification system performance, and how is it achieved? Unfortunately, the perceived complexity of classification systems, and the day-to-day time demands placed on the practicing metallurgist, all too often put the low-hanging fruit of classification system optimisation in the ‘I’ll do it later’ basket. Additionally, lingering confusion about basics such as the relationship between circulating load ratio and ball mill circuit performance makes the optimisation objective seem nebulous to both plant metallurgist and designer.Some of this confusion can be eliminated by taking a step back from the overwhelming detail of sharpness of separation curves, circulating load ratios, cyclone feed pressures, vortex and apex sizes etc, and focusing on the purpose or function of the classification system – to apply mill power to particles that need further size reduction! The classification system efficiency (CSE) metric captures how well the classification system is performing its function with two quick and easy size distribution analyses.Once CSE is understood and implemented as the optimisation criteria, well-tested methods for improving CSE can be implemented and quickly measured at plant scale to give confidence that the right change was made.This paper will describe CSE and how it is measured in practice. Next, a guide for improving CSE through manipulation of design and operating variables in the classification system will be provided. Examples and case studies will illustrate the gains in ball mill circuit efficiency that can be achieved by maximising CSE.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2018. A guide to maximising ball mill circuit classification system efficiency (CSE), for operators and equipment designers, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 553–558 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Mathilde Guilpain

A wide variety of plants are able to extract nickel (Ni) from soils and accumulate this metal in their foliage. Hydrometallurgical processes have been developed to recover Ni in the form of metal or salts, starting from the plant A. murale. They include: (1) a combustion step, to obtain ash containing 15–20% Ni; (2) a leaching step; and (3) purification. That whole flowsheet has been thoroughly investigated, and the processes scaled up to the pilot scale. Another strategy is presented here, consisting of recovering Ni without burning the plant. Ni can be extracted from the dry plant by water leaching, but the leachate is a multi-element solution from which Ni has to be separated. Selective precipitation of Ni hydroxide is not possible since Ni is bound to organic ligands. In this work, the plant leachate is processed by adsorption on the chelating resin DOWEXTM M4195. The results showed that Ni was selectively retained whereas the other main cations were not. Nickel could be recovered at the elution step. This methodology needs to be further investigated but these initial results are very encouraging and open the possibility of Ni recovery by agromining.

Projections of coal reserves in Central Appalachia are essential for long-term planning in the region. Annual production is declining in some states, such as Virginia, and mineable reserves for the Central Appalachian Coalfield are challenged by difficult geological, mining, and market conditions. In order to project coal mining longevity in this region, interviews with mining companies were conducted to assist in the determination and assessment of technical and economic factors that impact coal seam mineability. This information was applied to seam and coal reserve data developed by state and federal governments. The results were carefully analyzed to determine the effects of various factors on the overall mineable coal reserve base.

Jan 1, 1998

By Luis Amendola

El presente texto señala el proceso de diagnóstico e implementación de gestión de activos físicos en la producción de las operaciones mineras para aumentar su capacidad, al tiempo que elimina las pérdidas y aumenta la eficiencia en las operaciones. Para ello, se utilizó la metodología 3P+ PAM, donde se establece un punto de partida de forma científica y de negocio para definir cuáles serán las acciones que se deben ejecutar para alcanzar la meta y las buenas prácticas en la gestión de activos físicos de la empresa.

Sep 1, 2014

By S. Isaac

The networks of interdependencies between elements in building projects, referred to as the project topology, are often complex and difficult for project teams to comprehend. It is hypothesized that a graphbased model of the project topology can be based on existing data in Building Information Models (BIM), facilitating the application of graph-theoretic algorithms to analyze this topology. The objective of this study is to propose an outline for the synthesis of BIM and graph theory. This synthesis is expected to contribute to the development of new tools for representing, managing and analyzing the design of building projects.

Aug 1, 2013