Search Documents

By J. Handin

Triaxial compression tests with independently applied external confining pressures and internal pore pressures show that the ultimate compressive strengths of representative oil well cements are nearly linear functions of effective pressure — the difference between external and internal pressures on the jacketed cylindrical specimens (to 15,000 psi). The strengths are little affected by the test temperature to 350F (not to be confused with the curing temperature). At an effective pressure of 15,000 psi, strengths are in the rage of 30,000 to 50,000 psi, comparable to those of sedimentary rocks under similar conditions. The cements become very ductile even under low effective pressures; permanent shortenings of 30 per cent or more are attainable without rupture. INTRODUCTION Since the pioneering work of Richart, Brandtzaeg and Brown1 on the failure of cement under combined compressive stresses, it has been recognized that ultimate compressive strength is greatly enhanced by the application of confining pressure. More recently, Mc Henry2 showed that the strength of concrete was a linear function of the effective pressure (the difference between the external confining pressure on a jacketed specimen and the internal fluid pore pressure), at least for a range of 0 to 1,500 psi. The effect of temperature had not been investigated, and no previous systematic triaxial compression testing of naterials used for oilwell cementing seems to have been done. The present work was suggested by the late J. hi. Bugbee3 who stated that "consideration of the common application of high-pressure hydraulic fracturing to the initial completion or recompletion of wells, and the large pressure drawdowns in some producing wells, particularly those in abnormally high-pressure gas-condensate reservoirs, raises the question of what is a suitable cement strength for various completions. The intuitive belief exists that cement strength need be no greater than formation strength. Tests should, however, be conducted at downhole conditions." The ultimate compressive strengths of rocks penetrated by the borehole must rise several fold with increasing depth.4 This marked enhancement of strength is due to the influence of the effective pressure, the total weight per unit area of the overburden less the hydrostatic pore pressure. (The effect of temperature due to the geothermal gradients is relatively small for depths to 30,000 ft.) .A significant comparison of the strengths of rocks and cements at downhole conditions requires knowledge of the confined compressive strengths of cements as well. EXPERIMENTAL PROCEDURES The theory and technique of triaxial compression testing are fully discussed in earlier reports.4-6 Briefly, cylindrical specimens 1-in. long and 0.5-in. in diameter are jacketed in thin copper tubes of negligible strength, placed in the test chamber and subjected to an external confining pressure of kerosene and loaded axially by the piston at a strain rate of 1 per cent per minute. Pore pressures of water (or kerosene) are applied independently through the hollow piston and are maintained constant during the shortening of the specimen, Tests at sensibly 0 pore pressure are arranged so that any free water in the cement can escape to the atmosphere. (If egress of water were denied, pore pressure would rapidly attain the value of the external confining pressure because of reduction of pore space.) The test chamber can be heated for high-temperature experiments. Unless otherwise noted, the cement samples were air dried for about a week. Recorded during a test are pore and confining pressures, shortening and axial differential force (total force less the product of the confining pressure and the area of the piston). True stress-strain curves are constructed by dividing the measured differential force by the actual cross-sectional area of the specimen at a given

Jan 1, 1966

By J. B. Wagstaff, R. A. Buchanan, J. F. Elliott

High speed photography through blast-furnace tuyeres showed coke particles moving rapidly. Model studies showed a raceway was formed and gave quantitative results which were correlated with actual blast furnaces. Another study showed the similarity between hanging and the flooding of a packed column. This was explored by models. THE combustion zone before the tuyere in an iron blast furnace is a vital region because here are generated: 1—most of the gases on which the furnace depends to carry out its basic operation of reducing iron ore to the metallic state, and 2—the major fraction of the heat required in the nearby regions of the furnace for the various reduction reactions, the fusion of the slag, and the melting of the iron. Since the greater part of the coke is consumed in this region, the descent of the burden must be greatly affected by the characteristics of the tuyere zone. This region then would seem to be a profitable field for study. Fortunately, a view into this important zone is available to the operator through the tuyere peep sight. Here he sees relatively dark pieces of coke "dancing" in the blast. What he sees is of considerable help in interpreting the behavior of the furnace at a given time but the very rapidly moving particles and the intense radiation obscures what is happening very deep in the zone. This investigation was initiated in the hope that a better understanding of the combustion region could be obtained by using a high speed camera with a maximum speed of 3000 frames per sec. It seemed the best practical method of "slowing down" this characteristically violent action within the highly luminous field. Model studies and tuyere probing also have been used to aid in explaining the observed phenomena. Above the combustion zone, but below the fusion zone, there is probably a region in which the coke is comparatively stationary. Here are zones in which the gases must flow up through the granular bed counter to descending liquid slag and metal. There is no easy way to observe this zone in a blast furnace, but model studies have been of some help in explaining the nature of the zone and the laws governing the flow of the fluids involved. The whole problem is difficult and involved and any approach to a complete solution may require long investigation. This preliminary report has been written, therefore, because it is believed that appreciable progress has already been made that would be of interest to others. Tuyere Studies, Chemistry and Kinetics It is well known from the early work of Kinney and coworkers1,2 that combustion of carbon before the tuyeres appears to occur in two zones: Zone A: C + O, = CO2; AH77°F. = — 14,108 Btu per lb of carbon [I] Zone B: CO2 + C = 2CO; H77°F = + 6,183 Btu per lb of carbon [2] Zone A (Fig. 1) is close to the tip of the tuyere and zone B is somewhat farther back; there being a transition region in which both reactions occur. It is interesting to estimate the rate at which coke is burned before a tuyere with a wind rate of 90,000 cfm in a modern furnace having 18 tuyeres. Approximately 0.55 lb of carbon is consumed by eq 1 per tuyere per sec. A like amount disappears by eq 2 for a total consumption of 1.11 Ib per sec per tuyere. Assuming the coke is 85 pct C and has a bulk density of 30 lb per cu ft, this figure can be converted to a total of 1.30 lb of coke with a bulk volume of 0.043 cu ft disappearing per sec per tuyere. At the temperatures prevailing in the combustion zone (according to Kozlovich,³ he maximum is about 3400°F), the rate at which carbon is con-

Jan 1, 1953

By H. Bartholomew, L. Bernstein

Experirmental bonds of Ag-In SLID to gold, copper, nickel, Kovar, Dumet, nickel-plated molybdenum, ALL-Pt vrzetallizing on ceramic, and nickel-plated Mo-Ti metallizing on Al2O3 ceramic have been made and exalnined. Metallographic taper sections were made of all bonds for Phase identification. In addition, failuve temperatltres were determined for bonds heated undev shear load. Sowe bonds were subjected to electvon-probe microanalysis. The ternary SLID system Ag-In-Sn was similarly evaluated. Plwtonticrogaphs and electron-probe data are discussed and related to over-all phase diagrams , diffusion effects, and wetting properties of the liquid. The rates of diffusion andor compound formation of gold, silver, and copper in indium and In-Sn liquids are found to descend in that order, as measured by the relatzve thickness of phase layers in the interfaces of bonds made at 200to 400°C. It is concluded that the SLID process enables one to produce bonds which are stable at high temperatures, after having been fabricated at low temperatures, and meet most requirements for application in interconnection, silicon bonding, or hermetic sealing of electronic devices. In a previous publication by one of the authors, the theory and principle of SLID bonding in simple binary systems was discussed. SLID bonding can be defined as a joining process using a preform with a laminated structure: a low-melting material clad on a high-melting core. During the bonding cycle a metallurgical transformation occurs such that the resultant structure can withstand, without reliquefying, temperatures higher than those at which the bond was made. The phases present in the joint interface region are high-melting compounds or, if equilibrium is reached, solid solution. Properties will depend on the phases present, ultimately approaching those of the solid substrate core of the SLID preform. The high-temperature strength of bonds made in these systems was correlated to phase identification in the interfacial bond regions from metallographic cross sections and electron-probe X-ray microanalysis data. When complex electronic components are assembled, multiphase systems result at the interfaces of bond regions. In these ternary and higher-order systems very little diffusion and phase-diagram data is available with which to predict the nature of the interfacia1 region that will result from conventional fabrication processes and subsequent field use of the component. Clarke and Rhines did early work in the field using the Al-Mg-Zn system as a vehicle. Guy and co-workers studied a portion of the Cu-Zn-Ni system and some mathematical4 and general5 aspects of multiphase diffusion. irkald' and coworkerse recently studied diffusion in the Cu-Zn-Sn system. No diffusion studies have been made on ternary systems directly applicable to this investigation but some phase diagrams are available: g-u-n, u-i-n, and CU-i-n. I) DESCRIPTION AND EXPERIMENTAL PROCEDURE The elements Au, Ag, Cu, Ni, In, and Sn are found in alloy systems commonly used in fabricating and assembling electronic components. Reference to the appropriate phase diagrams9 and the previous publication will indicate that the binary systems of any of the two low-melting elements, indium and tin, with any one of the other four higher-melting elements are capable of producing SLID bonds. It is not unreasonable to assume that any ternary or higher-order alloy system containing at least one of the elements gold, silver, copper, or nickel and one or both of the elements indium and tin could be used to produce bonds which are stable at high temperatures, after having been fabricated at low temperatures. Indeed, the liquidus contours and isothermal sections of those phase diagrams available7 do so indicate. The parameters affecting the bond and the equipment used in evaluating the bond were described in an earlier paper.' The current investigation used the

Jan 1, 1967

By R. E. Ogilvie, J. I. Goldstein

The a and y solubility limits in the Fe-Ni phase diagram have been redetermined at temperatures above 500°C. Both a diffusion-couple and a quench and anneal technique were used. The solubility limits were measured with an electron-probe micro-analyzer. The nickel concentration at the phase boundary is increased below 700°C and the a solid-solubility range is much larger than had been previously measured. The solubility limits are also extrapolated to 300°C. It is suggested that the solubility of nickel in a FeNi reaches a maximum in the temperature interval 400o to 500°C. THE equilibrium diagram has been of great use in the field of meteoritics, where the phase relations between kamacite (a) and taenite (?) in metallic meteorites can be described by means of the Fe-Ni diagram. The study of metallic meteorites by electron-probe microanalysis has cast some doubt on the accuracy of the presently available Fe-Ni diagrams.1, 2 Recent thermodynamic studies of the Fe-Ni system also suggest that the diagram may be in error.3 For these reasons the high-temperature (800o to 500°C) part of the diagram was redetermined. INTRODUCTION The currently accepted Fe-Ni diagram is that of Owen and Liu.4 Above 910°C, there is a region of complete solid solubility, ? (fee). Below 910°C, the a (bee) phase is stable in pure iron. The effect of increasing amounts of nickel is to stabilize the y phase. The phases that form when Fe-Ni alloys are heated or cooled bear little relation to the equilibrium diagram. If an alloy is cooled from the y state and held at a temperature within the a + y field, no evidence has been found for the occurrence of the y - a transformation.5 If the alloy is cooled to low enough temperatures the y phase breaks down into a supersaturated bee phase called a2. In fact, in alloys over 27 pet Ni the y phase is retained at room temperature.6 The a, phase has the same composition as the original y. The temperature at which a2 forms, the M, temperature, has been determined experimentally.' A state of equilibrium can be approached by cooling below M, to form a2 and then reheating the alloy into the two-phase region of the diagram. The y phase will then begin to precipitate out of the a2 phase and grow. The growth of the phase, however, is quite slow. Using the interdiffusion coefficients -Da of Goldstein et al.,8 it is estimated that it takes about 1 year to grow a 10-µ-wide region of ? at 700°C in a 5 pet Ni alloy. Owen and Liu4 used the technique just described to form the equilibrium phases. The phases present were determined by means of X-ray analysis. The accuracy of their diagram depends on the number of alloys available near the phase boundary at a given temperature. In this study two different techniques were used to determine the a/a + ? and ?/a + ? solubility limits. The inherent accuracy of both techniques was greatly improved over that used by previous investigators because the phase-boundary compositions were measured with an electron-probe microanalyzer. PROCEDURE The two methods used to determine the Fe-Ni diagram are the diffusion couple (D.C.) and the quench-and-anneal (Q.+A.) techniques. In the first method, diffusion couples whose diffusion path goes through a two-phase region of the phase diagram were used. A description of the technique used for making the diffusion couples has been described in a previous paper.' After the diffusion treatment a discontinuity in the resultant concentration vs distance profile was measured. The nickel concentrations in the a and ? phases at the interface of the discontinuity are the solubility limits of the a and ? phases in the phase diagram at the diffusion temperature. If the interface com-

Jan 1, 1965

By N. A. Warner

Dense cylindrical specimens of artificial hematite were reduced in hydrogen over a range 0-f total pressures between 0.1 and 1.0 atm and temperatures between 650" and 950°C. Hydrogen reduction at a total pressure of 1.0 atm in the presence of a chemically inert diluent and reduction in hydrogen/water mixtures were also studied Znter.face movement during reduction was followed using metallographic techniques. Substantiu1 partial-pressure gradients are shown to exist in both the gas film and the reduced iron layer. The results are consistent with a mixed-control mechanism involving an interaction of gaseous-difusion effects with a first-order reversible chemical reaction at the iron/wüstite interface. Over the hydrogen-pressure range of 0.1 to 1.0 atm, the rate is not directly proportional to the hydrogen pressure in the bulk gas stream. Nitrogen dilution of the reducing gas masks the true effect of hydrogen partial pressure by influencing the effective molecular dif-fusivity and gives an apparent first-order relationship. The transport of hydrogen and water vapor across the iron layer is consistent with molecular gaseous diffusion rather than a Knudsen diffusion mechanism. ALTHOUGH the literature on the reduction of iron oxides is very extensive, it is only comparatively recently that a definite quantitative model for the reduction of hematite has been proposed. This development has been largely due to the work of McKewan. An extensive literature review of previous work has recently been compiled by Themelis and Gauvin. Exclusive control by gaseous diffusion in the reduction of hematite has been recently advocated by Kawasaki and coworkers.' Although the results of the latter workers are of considerable practical significance, the extreme porosity (approximately 30 pct) of their specimens precludes their application to a kinetic evaluation of the reduction of dense polycrystalline hematite. The salient features of the kinetic model used by McKewan for the gaseous reduction of dense hematite at temperatures in excess of 560°C (when FeO is stable) are: 1) The reduction is a topochemical reaction taking place through 'the series FeO/FesO4/FeO/ Fe; 2) The gas-solid type of reaction takes place only at the FeO/Fe interface and the internal reduction: FeO proceeds by solid state diffusion; 3) The iron layer formed is quite porous and offers negligible impedance to gaseous diffusion; 4) The rate-controlling step in the reduction is a chemical process occurring at the Fe/FeO interface. In view of the relatively fast reaction rates involved when hematite is reduced in a stream of hydrogen, it seemed possible that the simplifying assumptions of negligible diffusional resistance in both the bulk gas phase and the reduced iron layer could introduce serious errors in the interpretation of experimental reduction data. The present work was initiated to elucidate the effect of gaseous diffusion on the reduction rate and to determine its possible influence in the formulation of the reaction mechanism at the metal/oxide interface. EXPERIMENTAL Procedure and Apparatus. Dense cylindrical compacts of artificial hematite were prepared by sintering pressed compacts of reagent-grade ferric oxide, containing 99.6 pct FezO, in air at 1200°C for 80 hr. The resulting compacts had a final porosity of less than 2 pct and a height and diameter of approximately 1 cm. Variations in sintering atmosphere from air to pure oxygen, in sintering time from 20 to 80 hr, and temperature from 1150" to 1250°C had no effect on the subsequent reduction behavior. The reduction of the samples took place in a vertical tube furnace in which was placed a 1-in. transparent silica tube. The 24-in. heated length

Jan 1, 1964

By A. D. McMaster, M. L. Gimpl, N. Fuschillo

There is interest in the use of rhenium metal films as resistive elements in thin-film circcits, and already some zvork has been done using er)aporated rhenium films. It has been found that rheniim films protected from the atmosphere by an evaporated layer of silicon monoxide show excellent electrical stability. Unprotected films, however, are subject to aging- effects, notably the increase in electrical resistivity as a function of time. This phenomenon can be understood as primarily one of oxidation of the thin films. This paper is concerned with the study of the oxidation and crystallization behavior of such unprotected films. It has been found that the oxidation rates are a function of the substrate temperatures used during the deposition of Lhe metal films. The strictures observed in the films are correlated with the film resistivities and some data are presented to establish the existence of the various types of oxides of rhenium. ThERE is some interest in the use of thin films of rhenium metal as resistive elements in monolithic, thin-film integrated circuits. Some work has been done using evaporated films and it has been found that such films, if protected from the atmosphere by an evaporated layer of silicon monoxide, show excellent electrical stability up to temperatures of 500"." Rhenium films unprotected from the atmosphere tend to age and the electrical resistivity of the films increases as a function of time. Rhenium films, of the order of <100A thick, prepared by electron-beam evaporation techniques are found to oxidize very readily when exposed to dry air at room temperature. It would seem, therefore, that this aging phenomenon could be attributed to the oxidation of the metal films. In this investigation, the oxidation and crystallization behavior of thin films of rhenium evaporated onto silicon monoxide substrates were studied as a function of the substrate temperatures used during the evaporation. The films were examined using electron-microscopy and electron-diffraction techniques. EXPERIMENTAL RESULTS Rhenium metal was evaporated onto suitable prepared substrates which were heated to various temperatures. The evaporations were performed in a vacuum of approximately 5 x 1CT5 torr. The evaporation was carried out at a rate of approximately 10A per omin. The final film thickness was approximately lOOA and the resistance ranged from 5000 to 10,000 ohms per square. The substrates used for supporting the metal films were made by evaporating 75A of silicon monoxide onto freshly cleaved mica. The silicon monoxide film was then floated off the mica by immersing the composite in water. The film could then be picked up on a clean nickel grid. Silicon monoxide substrates were chosen because of their similarity to quartz and glass substrates commonly used for making thin-film resistors. Fuschillo, Gimpl, and McMas-ter have also shown that silicon monoxide films have only minor structural changes at temperatures up to 800°C. This fact simplified the interpretation of any changes observed in the electron micrographs or electron-diffraction patterns obtained from the deposited rhenium films. After the evaporations were completed, the substrates were cooled to room temperature, except where noted differently, before the coated substrates were removed from the vacuum system. All aging of the deposited films was done in a desiccator. The evaporated films were examined in an electron microscope equipped with a hot stage that would permit continuous observations of the samples up to temperatures of 1000°C. RESULTS A series of electron micrographs of the rhenium films deposited on the silicon monoxide substrates are shown to Figs. 1 to 3. In all cases, the metal films are approximately 100A thick and the micrographs were taken 1 hr after the deposition was completed. here was no apparent structure in the films deposited on the substrates held at the higher temperatures. The

Jan 1, 1967

By J. B. Coher, M. B. Bever

COLD work destroys long-range order, as was first observed by Dehlinger and Graf.1 Dahl2 showed that the mechanical disordering caused by cold work produces changes in those properties that are affected by long-range order. The existence of order has a marked effect on tile manner in which an alloy deforms and therefore on its mechanical properties.L&apos; The relation between order and deformation behavior however, is only beginning to be understood. Seemann and G1ander4 suggested that cold work reduces an ordered alloy to a kind of gruel of antiphase domains. According to Cottrell,5 superdis-locations and pairs of dislocations in a slip plane connected by a strip of anti-phase domain boundary provide deformation mechanisms which do not change the state of order. In general, however, slip may be expected to produce new domain boundaries and destroy order if dislocations move on intersecting planes or cut through existing domain boundaries. The yield strength of an ordered alloy may pass through a maximum with decreasing domain size.5"7 The reduction of domain size resulting from cold work may, therefore, lead to a maximum in strength properties. Flinn8 suggests that dislocations can climb by short-range diffusion during deformation and thus can generate domain boundaries not only on slip planes, but also on other planes which will be those with the lowest domain-boundary energy. It has long been known that the rate of strain hardening of an alloy in the ordered state is larger than in the disordered state.3&apos;9 Also the slip bands in ordered CU3, AU10 and Ni3Mn" are finer than in the disordered alloys. The stress which causes initial yielding in Cu,Au passes through a maximum with decreasing domain size.6&apos;12 A maximum has also been observed in the hardness of ordered Ni3Mn as a function of strain.&apos; These observations suggest, but do not prove, that domain size reduction occurs during deformation. According to Fisher13 slip destroys short-range order and thus the strength of an alloy is related to the degree of short-range order present. Rudman and Averbach14 and Averbach et a1.,15 demonstrated that cold work reduces short-range order in copper-gold and gold-silver alloys. Destruction of long-range and short-range order by cold work implies slip on an appreciable fraction of planes. Yielding of an alloy in which short-range order exists or antiphase domain boundaries are present should be discontinuous because the first dislocations moving across the slip plane meet with the largest resistance.5 Such discontinuous yielding has been observed in CU3AU6,16 and Cuzn.l7 This phenomenon, however, can also be explained by mechanisms not involving order.b The published investigations of the effects of cold work on alloys with long-range or short-range order have not been covered thoroughly in reviews of order-disorder phenomena. These investigations, therefore, will be listed here. They have been concerned with strength properties> 2,3,6,8,9,12,16-21 electrical resistivity,2,4,18,19,21-26: thermoelectric power, magnetic properties,2,18,21,26 and X-ray strain&apos;1,2,14,15,27,28 The slip systems and the appearance of the microstructure after deformation in ordered and disordered alloys have also been investigated. 6.10.ll,l7,23,29,30 The alloys used in these investigations were copper-gold. 1-4,6,9,10,14,16,18 23-26,28,29 copper-zinc. L7. 19. 20,30 nickel-manganese,2 11,21 iron-aluminum. iron-nickel,&apos; copper palladium,4,18,22 gold-silver.4,18,22 and palladium-silver-copper.4 In the work reported here. the changes in properties of polycrystalline Cu3Au were investigated as functions of strain in wire drawing and rolling. Specimens were heat treated before deformation

Jan 1, 1961

By J. Brett, S. Friedman

A study of the diffusion of nickel into both fibrous and recrystallized 0.065-in.-diam silica-alumina doped tungsten wire at 1200°C has been conducted. The diffusion profiles were determined by chemical dissolulion of successive circumferential layers and spectro-photometric determination of nickel in the etchant. It was shown that the diffusion of nickel into tungsten is markedly structure-sensitive. No significant amount of nickel could be introduced at 1200°C into tungsten which had first been recrystallized at temperatures of 2300°C, leading to an upper limit estimate for the bulk diffusivity of nickel in tungsten of 10-11 sq cm per sec at 1200°C. However, nickel did diffuse into initially fibrous wires, caused re crystallization, and was alsays present at the advancing recrystallization front. The accumulation of nickel in an initially fibrous region ceases when the recrystallization front arrives. The characteristics of the resulting diffusion profiles are explained in terms of the relation between diffusion processes and micro structural changes. WHILE it is well-known that the presence of nickel and certain other metals causes low-temperature recrystallization of the cold-worked fibrous structure of doped tungsten,&apos;&apos;&apos; the character of the phenomenon is not well understood. Recently it was shown that the recrystallization reaction can be induced at low temperatures by the presence of solid nickel on the surface of doped wire, but not by exposure to nickel vapors.3 Once recrystallization was initiated, a continued source of nickel was required for propagation of the recrystallization front. The phenomenon appeared to be a complicated solid-state reaction since, in addition to the change in structure of the tungsten from fibrous to equiaxed grains, diffusion of nickel from the surface into the recrystallized and fibrous structures was occurring with possible chemical reaction between nickel and tungsten at the surface and interaction of nickel with the dopants which ordinarily stabilize the fibrous structure within the wire. The objective of the present work was to study the diffusion of nickel into fibrous and recrystallized tungsten structures in order to clarify the relationship of the diffusion process to nickel-induced recrystallization. Studies of interdiffusion in the Ni-W system4"7 have been principally concerned with the mobility of tungsten in nickel. Information on diffusion of nickel in tungsten is meager, and there seem to be no studies of the mobility of nickel in tungsten which elucidate the structural aspects of the phenomenon. The present experiments were designed to determine the diffusivity of nickel at 1200°C in fibrous tungsten, in large-grained tungsten prerecrystallized at high tem- perature, and in tungsten recrystallized at 1200°C due to the presence of nickel. Although the concentration profiles were determined in these experiments, unexpected changes in boundary conditions or complex diffusion paths complicated the analysis of these profiles so that the interpretation could not be readily expressed in terms of simple diffusivities. EXPERIMENTAL PROCEDURE The experiments were conducted on Sylvania 0.065-in.-diam silica-alumina doped commercial tungsten wire, hereafter designated as ordinary doped wire. A special lot of 0.065-in.-diam silica-alumina doped low-nickel wire was also used. Impurity analyses of the wire are given in Table I. The experimental design is shown in Fig. 1. All heat treatments were conducted in vacuum. Two groups of ordinary doped wire were prepared for diffusion with nickel. One group in the as-received (fibrous) condition was elec-tropolished, nickel-plated, and annealed at 1200°C for 20 and 40 hr, or was exposed to nickel vapor at 1200°C for 20 and 40 hr. The second group was recrystallized to an equiaxed grain structure at 2300°C for 3 hr, electropolished, nickel-plated, or exposed to nickel vapor for anneals at 1200°C for 20 and 40 hr.

Jan 1, 1969

By S. Korman, S. B. Tuwiner

THE purpose of this study is to investigate the effect of agitation upon the flotation of chal-cocite. It is believed that the concentration of collector which is required to produce a water-repellent surface upon the mineral is determined among other things by the rate of collector diffusion through an impeding film of more or less stagnant fluid. Its thickness depends upon the intensity of agitation. In the first part of this study a method is developed for determining the thickness of the fluid film upon a polished surface of synthetic chalcocite. The film thickness is then determined as precisely as possible under three readily reproducible condi-tions of agitation intensity. These determinations serve as a quantitative evaluation of agitation. In Part 2 it is demonstrated that in solutions of lime at PH 10.5 and in the absence of air or dissolved oxygen the concentration of collector required to develop water-repellency upon the surface in any given time is a function of the fluid film thickness, and that after about 10 min the relation becomes linear. This points to the possibility that the collector ions may be involved in a diffusional process through the fluid film. In Part 3 it is shown that where air is present more collector is required to produce water-repellency than for the case in which air is excluded. Next, it is shown that for the latter case the most minute amount of sodium sulphide suffices to preclude development of water-repellency. Both oxygen and sulphide are in a sense, therefore, depres- sants for chalcocite in a lime solution at PH 10.5. When oxygen and sulphide are present simultaneously there is a region of minimum critical collector concentration for water-repellency which is very markedly lower than the concentration where oxygen alone or where sulphide alone is present. Moreover, this minimum appears to be identical with the collector concentration which is required where sulphide and oxygen are both excluded. This would appear to indicate that in certain ranges of concentration of oxygen and sulphide, each cancels the effect of the other. The range of concentration of solution for this effect in solutions saturated with oxygen is a function of the agitation intensity. Thus we are led to believe that a chemical reaction involving sulphide and oxygen occurs at the surface of the chalcocite. Part 4 of this study is a further development of this idea and some of its consequences from an electrochemical standpoint, while in Part 5 the disappearance of sulphide from pulps of several minerals is noted with an indication that both dissolved oxygen and the mineral are necessary, the reaction being catalytic or pseudocatalytic. Part 1. Determination of Fluid Film Thickness The Fluid Film Concept: The hindrance to the diffusion of collector to the surface of the chalcocite is a barrier of stagnant fluid in the vicinity of the surface. It is the same barrier that limits the rate of transfer of heat, the rate of solution of dissolving crystals, or any of the other rates pertaining to chemical engineering unit operations in which the film resistance to diffusion plays a principal role.&apos; Fluid films are present upon the surface to an extent which varies with the geometry and intensity of agitation. They result from the fact that in the region within the fluid near a surface, motion is entirely parallel to it. From the standpoint of transfer to or away from the interface the effect is as though the fluid were stagnant. Outside of the film, movement of the fluid may be streamline or turbu-

Jan 1, 1951

By M. J. Pool, with Appendix by Larry Kaufman, R. W. Krenzer

Thermodynmic properties of the Cu-Mn system have been deterrrzined in the temperature range 973" to 1273°K by measuring the vapor pressure of manganese in equilibrium with alloys of compositions varying from 0.13 to 0.91 rnole fraction manganese using the Knudsen effusion technique. Activities of manganese calculated from the measured vapor pressures show large positive deviations. Calculated heats and entropies of mixing are positive with a maximum occurring at approximately 0. 7 mole fraction manganese. ThE investigation of thermodynamic properties of binary systems involving transition metals is of considerable interest at the present time. The incomplete subvalency electron levels of transition metals lead to unusual behavior in some alloys, and considerable information can be obtained by determining the thermodynamic characteristics of these systems and relating the thermodynamic behavior to observed physical properties. The Cu-Mn system, shown in Fig. 1,&apos; provides an example of an alloy system in which the determination of the equilibrium phase diagram and various physical properties has received considerable attention, but very little work has been done on measurement of the thermodynamic properties. Elemental copper and manganese have comparable electronegatives, atomic sizes, and cohesive energies, but differ in crystal structure. They form a continuous series of solid solutions only at high temperatures and the structure varies in a continuous manner from fcc at the copper-rich end to fct at the manganese-rich end.&apos; The purpose of this investigation was to measure the vapor pressure of manganese over a series of Cu-Mn alloys and from these values determine the thermodynamic properties of the binary system. Vapor pressure measurements were made in the temperature range 973" to 1273"K, remaining within the solid-solution region for each alloy studied. EXPERIMENTAL PROCEDURE The relative thermodynamic properties of solid Cu-Mn alloys were determined from vapor pressure measurements by means of the Knudsen effusion tech- nique. Several discussions of the theory can be found in the literature. In the case of copper and manganese, it is assumed that manganese is the only component subliming, so the vapor pressure of manganese over the various alloys can be determined directly by measuring the weight loss of the effusion cell. This is a valid assumption since the vapor pressure of manganese is about four orders of magnitude higher than the vapor pressure of copper in the temperature region of interest. The vapor pressure of manganese over the alloys at any given temperature is then related to the weight loss of the effusion cell per unit area per unit time. An upper limit of 1.5 x 10"s has been measured for the ratio of polyatomic to monoatomic molecules for manganese vapor in equilibrium with solid manganese at 1180°K, so it was assumed that manganese vapor is monoatomic. The effusion cells, fabricated from high-purity alumina, are 26 mm high, 18 mm OD, and have a wall thickness of 1 mm. Three different sized holes of 2.03, 2.54, and 3.18 mm diam were drilled in the lids from the inside face to minimize chipping, and the lids were then slip-cast onto the cells to provide a gas-tight seal. Alumina was selected for this particular application both because of its resistance to thermal shock and reaction with manganese vapor. In the ideal case, the orifice of the effusion cell should have a knife edge so that effusion through the orifice

Jan 1, 1970

G. D. Kneip, Jr., and J. 0. Betterton, Jr. (Union Carbide & Carbon Corp., Oak Ridge, Tenn.)—The authors have contributed to the theory of zone melting by considering the effects of the solidification of the final zone on the distribution curves for the finite length bar. However, they do not consider in sufficient detail the restrictions imposed by the particular metals involved. Eq. 4 has the analytical solution which is equivalent to Pfann&apos;s&apos; equation for normal solidification of the final zone. For distribution coefficients less than one, it is apparent from this form of the equation that, as the solidification approaches completion, the concentration attains extremely large values which are inconsistent with the density of physical materials. The necessary restrictions then are that the solute concentration cannot exceed the density of the alloy, or more frequently, the solubility limit in the solid phase. Secondly, the distribution coefficient cannot be constant from 0 to 100 pet solute unless the liquidus and solidus coincide over this whole region. It would thus be more correct to impose limits on the solubility such as would be indicated by a typical eutectic diagram. Furthermore, in this case the assumption that the distribution coefficient remains constant is more likely to be realized. Eq. 4 should then be replaced by the following C,,(x) =k/L-x [ ?11 3 C11 (x)Ddx - ?11 4 Cn(x)dx= k[Cn (L-l)/k] [ L-x/l]x-1 L-l = x = L-l [kCenterlie/Cn (L-l)]1/k-1 The typical shape for the distribution curve in the final zone is indicated schematically in Fig. 12 for the simple eutectic case. The solidification proceeds according to Pfann&apos;s&apos; expression until the concentration reaches the maximum solubility in the solid phasc. At this point, the concentration changes abruptly to the eutectic composition and remains at this value for the duration of the solidification. The width of the flat region, and the back reflection of this effect into the concentration curve on subsequent passes, depends upon the ratio of the eutectic concentration to the original concentration, upon the distribution coefficient, and upon the number of passes. Similar effects on the concentration curves in the first zone length would be expected in many systems for which the distribution coefficient is greater than one, and where the maximum solubility is not too much larger than the original concentration. The discussers agree with the authors that the assumption that the liquid is uniform in concentration should be considered with caution. Kneip and Better-ton&apos; have shown, however, that in floating zone refining of zirconium, using induction heating, the distribution of iron agrees with theory which assumes a uniform liquid composition. Hence, in this case, the experimentally realized distribution coefficient agrees with the present phase diagram within the experimental uncertainty. L. Burris, Jr., C. H. Stockman, and I. G. Dillon (authors&apos; reply)—The authors are happy to have received the comments of G. D. Kneip, Jr., and J. 0. Betterton, Jr., which provide additional insight into the zone refining process. It is true that the equations developed are inapplicable if the solute solubility in the solid phase is exceeded. However, this restriction on the use of the equations was clearly stated in the paper. A closer approach to

Jan 1, 1957

By R. F. Domagala, D. J. McPherson

Iodide zirconium was combined with calculated amounts of ZrO2 or master alloys and arc-melted. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat treated specimens permitted construction of the binary phase diagram from zirconium to ZrO2. Oxygen additions to zirconium raise the transformation temperature as well as the melting point. Features of the diagram include the peritectic formation of beta, the formation of alpha directly from the melt, an intermediate phase ZrOB with a&apos; range of homogeneity, and a eutectic between alpha and Zr02. PHASE relationships in the Zr-0 system were determined in the range 0 to 66. 7 atomic pct 0 (ZrO,). Arc-melted alloys were annealed at temperature levels between 600" and 2000°C. Determination of the phase boundaries was accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to determine solidus curves, and X-ray diffraction work was employed to study the lattice parameters of the a solid solution and the phase ZrO,. Experimental Procedures Westinghouse "Grade 1" iodide zirconium crystal bar (approximately 99.8 pct pure) was employed for the investigation. This material is substantially free of the impurity inclusions characteristic of most zirconium metal. Previous work has shown it to be the most satisfactory grade for phase diagram studies. The zirconium crystal bar, as-received, was coated with corrosion product from autoclave tests by which its grade designation is determined. The bars were sand blasted lightly, pickled for 1 min in a 20 pct HN0,-5 pct HF aqueous solution, rinsed in water and acetone, and dried. The bars were rolled to about 1/32 in. strip, cut into 10 in. lengths, and pickled again. The material was sheared to approximately Y4 in. squares, cleaned with acetone, and stored for use. Two pounds of specially prepared "chemically pure," and 100 grams of spectrographic grade ZrO, were obtained for the preparation of alloys. The "Specpure" ZrO, was obtained from Johnson, Mat-they Co.. Ltd.. and Titanium Alloy Manufacturing Div. of National Lead Co. supplied the other grade of oxide. The "chemically pure" material (henceforth referred to as C.P. ZrO,) was used for the preparation of all alloys employed in the determination of phase relationships. A limited number of alloys were prepared with the "Specpure" oxide to recheck certain phase boundaries. Analyses of the two grades of oxide are given in Table I. The C.P. ZrOI was received in powder form, not suitable for arc melting. Therefore, this material was compressed to wafers 1 in. in diameter and about Vn in. thick. These were segmented and stored for use. The "Specpure" material, in the form of small granules, was suitable for use in the as-received condition. A nonconsumable electrode arc-melting furnace was used to prepare alloys. A water-cooled copper crucible and tungsten-tipped electrode were employed. The material was placed in the crucible and rapidly melted under a protective atmosphere of helium gas by striking the arc on a tungsten stud and directing it upon the charge material. Details of operation, including drawings of this type furnace, have been published.&apos;

Jan 1, 1955

By F. V. Lenel, J. A. Dromsky

The influence of thermal and mechanical treatments upon the elevated-temperature stability, the microstructure, and the mechanical properties of aluminumaluminum oxide alloys is investigated. Compacts from atomized and flake aluminum powders were sintered at temperatures just below the melting point of aluminum in a vacuum of 10-4 Torr for several hours and were then hot-extruded. During this treatment the hydrated oxide present on the surface of the powder particles decomposes, the water vapor produced reacts with the aluminum forming additional oxide, and the hydrogen developed is removed by diffusion to the surface. Extrusions of compacts so treated are stable at temperatures up to the melting point of aluminum and do not form blisters and internal defects typical of extrusions from untreated powder. Electron micrographs of extrusions from unsintered compacts show long parallel oriented platelets typical of the IN previous investigations1,2 the properties and structure of aluminum alloys were described which had been produced by cold compacting aluminum powder and then hot pressing and extruding the compacts. Both the structure and the properties of these alloys differ significantly from those of commercially produced aluminum-aluminum oxide alloys. When commercial alloys are produced, they are given a sintering treatment in air at about 600°C between cold compacting and hot pressing.3 During this treatment the hydrated oxide, which forms the coating on the aluminum-powder particles from which the alloys are prepared, is decomposed.4 The chemically bound water which is released reacts with the aluminum and forms aluminum oxide and hydrogen. Most of the hydrogen is eliminated by hydrated oxide skins on the original powder particles, while the oxide particles in extrusions from sintered compacts are broken up. The strength of extrusions from treated powder is somewhat lower, but their ductility is considerably improved over that of extrusions from untreated powder. The slip-trace patterns on electron microgvaphs of extrusions which had been strained in tension before replication indicated that the grain size of the extruded alloys was approximately the same as that of the original powder particles. Coarse-grained alloys were produced by severe cold work and annealing of the extrusions. They have significantly lower room-temperature strength, but about the same ductility as the vacuum-sintered fine-grained alloys. The size and shape of oxides in the coarsegrained alloys is similar to those of the fine-grained alloys, but the particles are somewhat more uniformly distributed. diffusing to the interior or exterior surfaces of the compact, but it is difficult to eliminate all of it because the solubility of hydrogen in solid aluminum is very low even near its melting point. Extruded alloys which are not sintered before hot pressing and extrusion appear quite sound upon metallo-graphic examination, but develop severe surface blistering and internal fissuring when they are heated to elevated temperatures after extrusion. Fissures and blisters have been observed even in commercial alloys which had been sintered in air, although they are much less severe.&apos; Because of the importance of this sintering treatment it was studied in this investigation in a modified form, using vacuum sintering rather than sintering in air, to insure more complete elimination of occluded hydrogen. The technique is described and the effect of the treatment upon the structure of the alloys is documented. It has been known for some time that extruded aluminum-aluminum oxide alloys are very finegrained, but an exact delineation of grains in electron micrographs has not been possible. In the conventional metallographic-etching techniques etchants attack the interface between the second-phase particles and the matrix in the alloys much

Jan 1, 1964

For all the attention given to mining activities in Central and South America, Mexico, Indonesia and Papua New Guinea, it is sometimes easy to forget the activities taking place in one of North America&apos;s most important and largely untapped regions -Alaska. The Alaskan minerals industry employed about 3,406 people during 1995. That is a 23% increase from - - 1994. It also contributed about $719.8 million to the state&apos;s economy during 1995, a 10% increase. During the past few years, Alaska has seen significant increases in exploration and mining activity. Fairbanks Mining, an arm of Cyprus Amax, began producing gold during 1996 at its Fort Knox Mine, as did Nevada Goldfields&apos; Nixon Fork gold mine. Kennecott&apos;s Greens Creek lead-silver-gold mine also reopened and USMX began operations at its Illinois Creek gold mine. In addition, several impressive exploration projects were under way in Alaska. Placer Dome reported good results at Donlin Creek project in southwest Alaska. Likewise, Newmont Exploration is getting serious about its True North gold project. And Nerox is nearing production at its Jonesville coal project in Alaska&apos;s interior. In November, about 400 miners gathered in Anchor- age for the Alaska Miners Convention. Throughout the conference and exhibition, attendees listened to updates on these precious- and base-metal and coal exploration and mining operations. They also learned that the state wants more miners to head north and help develop its natural resources. Alaska is ripe for a smelter The mining industry -Alaska&apos;s miners in particular - has a powerful ally in Sen. Frank Murkowski (R-AK). He is the chairman of the Senate Energy and Natural Resources Committee. During his luncheon address, Murkowski said it appears that it is economically feasible to extend the Alaska Railroad to northwest Alaska, taking advantage of the large coal and hard-rock mineral tracts in the Ambler mining district. He also renewed his push for building a major smelter in Alaska to process ore that would come from the Ambler mining district. Murkowski believes that Alaska&apos;s economy can be expanded by extending the railroad from Nenana to the Point Lay coal fields to open coal development. Along the way, the railroad would pass through the Ambler district, helping to develop the hard-rock deposits. An outgrowth of this additional mineral development, Murkowski said, could be a new smelter in Alaska. It could use power from the Tyee hydroelectric facility near Wrangell or from the Makushin geothermal project near Unalaska. Either site, he added, offers access to plentiful, relatively low-cost power, at tidewater to facilitate ore deliveries to the Pacific Rim. The Congressional Research Service has determined that there are enough mineral deposits and coal beds to make it possible to finance the extended railroad, he said. The 1,200-km (744- mile) rail extension would cost about $4.2 billion. The North Slope of Alaska contains up to 3.6 Tt (4 trillion st) of coal, Murkowski said, that contains less than 0.25% of sulfur and less than 4% moisture. It aver- ages 12,300 Btu in heat content. "That is a tremendous resource," he said. The Ambler mining district, meanwhile, has at least eight identifiable hard-rock deposits, Murkowski continued. These contain zinc, lead, copper, nickel, chromium, tin, barite, gold and silver. "All eight of these can generate ore concentrates at rates similar to Red Dog&apos;s cur- rent 725 ktla (800,000 stpy)" of zinc, he said.

Jan 1, 1997

By S. H. Moll, R. E. Ogilvie

The investigation of solid-state diffusion phenomena may lead to much information concerning binary alloys. In particular, a study of the concentration gradients present in multiphase diffusion couples can lead to the determination of the solubility limits of the single-phase fields in the phase diagram. The specific concentration gradient which results from the heat treatment of a diffusion couple depends not only upon the time and temperature of diffusion, but also upon the number of phases existing in equilibrium at the diffusion temperature. Such concentration gradients possess sharp discontinuities whose terminal points correspond to the solubilities existing at the limits of the two-phase field in the phase diagram at the diffusion temperature. In general, there will be a discontinuity in the concentration curve for each two-phase field which exists in the phase diagram between the concentration limits of the couple. A number of investigators have analyzed the gradients present in multiphase diffusion couples. 1-8 The iron-titanium phase diagram exhibits a y loop in the temperature range from 900" to 1400°C, and the limit of the a + y field lies at some composition which is less than 1 wt pct Ti for any temperature. It was felt that a diffusion study could yield values not only for the diffusion coefficients involved, but also for the chemical solubilities in the phase diagram. The concentration gradients were analyzed by an X-ray absorption technique developed by Ogilvie.6 The absorption of a monochromatic X-ray beam is measured in steps parallel to the diffusion direction and the resulting intensity gradients are transformed into concentration gradients by applying the laws of X-ray absorption in a binary system. This technique has been applied by ogilvie6 to the systems Ni-Au, Cu-Au, Fe-Cr, and Ni-Cr; by Gelles7 to the systems Be-Fe, and Be-Ni and by Hilliarde to the system Al-Zn. Linear X-Ray Absorption Analysis—The use of X-ray absorption analysis as a tool for determining concentration gradients arises from the fact that the beam is absorbed according to the quantity and species of elements present in the sample and not according to their state of aggregation. This method is more advantageous than the chemical analysis of machined layers since it is less time consuming and less expensive and can analyze a very small area. IF a homogeneous binary alloy (A + B) is analyzed with two different monochromatic X-ray beams I0(2) and lo(2) the following relation between the transmitted intensities, the intrinsic absorption coefficients of A and B for the two different radiations and the weight fraction of each element may be derived.&apos; In (I/Io) (a+b) xa(u/p)a(2) + xb(u/p)8(2) Eq. [1] is independent of specimen thickness and density, but requires that either element A or B possess an absorption edge between the wavelength limits of the two monochromatic beams. I, is evaluated for each radiation by measuring the transmitted intensity through a varying number of foils of a suitable absorber. A plot of the natural logarithm of the transmitted intensity as a function of the number of foils, when extrapolated to zero foils, yields the value of I,. If a plot of the ratio in Eq. [ I] is calculated as a function of xA, then a master curve results. From

Jan 1, 1960

By J. W. Wolfe

The Benedict-Webb-Rmbin equation of state was used in digital computer programs to make rapid determinations of natural gas equilibrium phase compositions. Mixture components were the nine hydrocarbons, methane through heptane. Comparative tests were made with data from field separators, plant exchangers and literature sources. For most tests made, the B-W-R equations predrcted component K-vallles, mixture enthalpies and phase aensities within tile accuracy of available correlations for rune-component mixtures: significant deviations were noted when mixtures contained components heavier than heptune. INTRODUCTION Rapid, accurate methods for calculating the properties of hydrocarbon mixtures are needed for predicting the behavior of natural gas processes. For example, because of the common use of two-phase separation methods in gas proccssing, calculations must be made for the density and composition of equilibrium vapor and liquid phases. In addition, predictions must often be made for the temperature and pressure changes associated with the flow of single- and two-phase natural gas fluids through heat exchangers, chokes and turbines. The complex nature of non-ideal mixtures makes rigorous calculations for these natural gas properties difficult and time-consuming. Natural gas properties have conventionally been determined with generalized data correlations. These correlations, such as the K-values presented in the NGAA Equilibrium Ratio Data Book, are usually based on some average property of the mixture and have proven to give satisfactory estimates for the properties of most oil and gas systems. Digital computers, however, have not only increased the utility of these correlations, but also have made practical the use of equations of state for calculating the properties of natural gases. Potentially, if basic pure component data are available, all the desired thermodynamic properties of mixtures can be derived from a single equation of state describing the mixture. Currently. the best equation of state for describing the behavior of pure, light hydrocarbons over single-and two-phase regions, both below and above critical pressure, is that of Benedict. Webb and Rubin.&apos; The equation contains eight constants which are determined by empirically fitting the equation to pure-component PVT data. Benedict and his co-workers presented the clevelopment of their equation as early as 1940.2 The B-W-R equation is a modification of the Beattie-Bridgeman equation of state and gives better PVT predictions than the Beattie equation at densities above the critical density. Benedict et al. made the equation applicable to mixtures by relating the mixture constants to composition and the constants for pure compounds. These authors, in a serics of articles in 1951,&apos; showed the accuracy of the B-W-R equation when applied to light hydrocarbons and their simple mixtures, and demonstrated the equation&apos;s utility for making vapor-liquid equilibria calculations. Since its inception, the B-W-R equation has been the subject of many papers. Numerous additions and modifications have been proposed,&apos;-&apos;,"&apos;-&apos;:&apos; the purpose of most being to improve the equation&apos;s ability to predict PVT properties of specific mixture systems. In 1959, Opfell, Pings and Sage summarized much of the work on the B-W-R equation in their book on equations of state." Since natural gases are primarily mixtures of light hydrocarbons, the B-W-R equation is a natural choice for an equation of state to compute both phase equilibria and thermodynamic properties of natural gases. Consequent-

Jan 1, 1967

By S. Korman, S. B. Tuwiner

THE purpose of this study is to investigate the effect of agitation upon the flotation of chal-cocite. It is believed that the concentration of collector which is required to produce a water-repellent surface upon the mineral is determined among other things by the rate of collector diffusion through an impeding film of more or less stagnant fluid. Its thickness depends upon the intensity of agitation. In the first part of this study a method is developed for determining the thickness of the fluid film upon a polished surface of synthetic chalcocite. The film thickness is then determined as precisely as possible under three readily reproducible condi-tions of agitation intensity. These determinations serve as a quantitative evaluation of agitation. In Part 2 it is demonstrated that in solutions of lime at PH 10.5 and in the absence of air or dissolved oxygen the concentration of collector required to develop water-repellency upon the surface in any given time is a function of the fluid film thickness, and that after about 10 min the relation becomes linear. This points to the possibility that the collector ions may be involved in a diffusional process through the fluid film. In Part 3 it is shown that where air is present more collector is required to produce water-repellency than for the case in which air is excluded. Next, it is shown that for the latter case the most minute amount of sodium sulphide suffices to preclude development of water-repellency. Both oxygen and sulphide are in a sense, therefore, depres- sants for chalcocite in a lime solution at PH 10.5. When oxygen and sulphide are present simultaneously there is a region of minimum critical collector concentration for water-repellency which is very markedly lower than the concentration where oxygen alone or where sulphide alone is present. Moreover, this minimum appears to be identical with the collector concentration which is required where sulphide and oxygen are both excluded. This would appear to indicate that in certain ranges of concentration of oxygen and sulphide, each cancels the effect of the other. The range of concentration of solution for this effect in solutions saturated with oxygen is a function of the agitation intensity. Thus we are led to believe that a chemical reaction involving sulphide and oxygen occurs at the surface of the chalcocite. Part 4 of this study is a further development of this idea and some of its consequences from an electrochemical standpoint, while in Part 5 the disappearance of sulphide from pulps of several minerals is noted with an indication that both dissolved oxygen and the mineral are necessary, the reaction being catalytic or pseudocatalytic. Part 1. Determination of Fluid Film Thickness The Fluid Film Concept: The hindrance to the diffusion of collector to the surface of the chalcocite is a barrier of stagnant fluid in the vicinity of the surface. It is the same barrier that limits the rate of transfer of heat, the rate of solution of dissolving crystals, or any of the other rates pertaining to chemical engineering unit operations in which the film resistance to diffusion plays a principal role.&apos; Fluid films are present upon the surface to an extent which varies with the geometry and intensity of agitation. They result from the fact that in the region within the fluid near a surface, motion is entirely parallel to it. From the standpoint of transfer to or away from the interface the effect is as though the fluid were stagnant. Outside of the film, movement of the fluid may be streamline or turbu-

Jan 1, 1951

By B. K. Gorain

"Mining of low grade deposits along with the necessity to design and operate flotation plants with high throughput presents unique metallurgical and environmental challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life of a mine.Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy, the need to use poor quality water such as brackish or sea water, reduce environmental impact from the process, integrate flotation with hydrometallurgy to maximize precious metals recovery, escalation of capital and operating costs, use of unproven technology and constant use of larger equipment, high ore variability, worldwide constraints on resource availability and an ever increasing need for reliable metallurgical input to financial models to evaluate economic viability of projects.The need to develop effective solutions to these problems in a short time frame is becoming a key to the success of any new project and for sustaining the profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial with the need for a more lateral thinking along with strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex flotation problems.INTRODUCTIONThere are various challenges to successful development of mineral resources. Most of the ore bodies being developed worldwide are of lower grades requiring high throughput to be economical. Many of these lower grade ore bodies have significant occurrences of deleterious and penalty elements that could render a deposit unworthy of development unless there are technological solutions to process them economically in a sustainable manner with minimal environment impact. Even in a high metal price scenario, the economics for some of these low grade ore deposits is marginal. From a metallurgical perspective, these ore bodies have complex mineralogy and use of any off-the-shelf technology is not always effective. Development of innovative processes are often required, which is expensive, time consuming and sometimes risky.This paper will provide a broader perspective on the steps involved in solving flotation problems for operating plants and for greenfield development projects. In addition, some of the key challenges in flotation of complex low grade ore bodies along with the economic benefits in developing solutions to these problems will be presented."

Jan 1, 2013

By Francis Kendorski

The Skyline #3 Mine of Canyon Fuel Company in Utah was planning longwall mine development adjacent to and downdip of older mine workings known to be flooded. Barrier pillar geometries and widths were proposed by mining company personnel. Hydraulic conductivity testing suggested that the general characteristics of the local coal seam, dikes, and faults are only weakly conductive and that leakage through the barriers, if any, would be minor. The mechanical performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods and (2) numerical stress modeling. Comparison of the proposed design, with the range of barrier widths derived from the empirical methods, served as a first-order check on the adequacy of the proposed design. Numerical modeling was used to evaluate conditions site-specific to the Skyline #3 Mine and barrier geometry. Models were developed to quantify the relationship between barrier width and the abutment stresses onto the future workings. The models were also used to estimate the stress distribution within the barrier pillars. The hydraulic performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods for hydraulic impoundments, (2) empirical method estimates of seepage through coal barrier pillars, (3) numerical hydrogeologic flow modeling, and (4) numerical strain modeling. Using the techniques described above, and based on relevant industry experience, underground observations, knowledge of local geologic conditions, hydrogeologic measurements, and analytical results, the level of geomechanical risk associated with the barrier design as proposed was considered low and the level of hydraulic risk was considered moderate. The largest uncertainty that remained was the possibility that unfavorable geologic structures, such as faults and dikes, would act as conduits for leakage of impounded water into the new workings. Although the study indicated only minor steady-state leakage would occur through a small number of known structures, the presence and full leakage potential of threatening structures in the barrier could not be reliably known until the barrier was mined. One longwall panel has been completed adjacent to the barrier with no evidence of water flow even in fractured zones. Thus, as predicted by the modeling and analysis, it appears that abutment stresses imparted on the barrier during mining did not substantially alter the natural hydrogeologic characteristics, or leakage potential, of the barrier. The longwall coal mine water-barrier pillar design and performance are considered a success.

Jan 1, 2007

By T. J. DeMull

More than 1.81 mt (2 million tons) of low grade ore have been heap leached at the Alligator Ridge mine. Since inception of leaching in 1980, several modifications have been made to ore agglomeration, heap construction, and leach operation practice. These modifications have improved the percolation rate of the ore and the rate of gold extraction from the ore. Changes made in each of these areas are described and the effects of the changes are discussed.

Jan 1, 1984