Search Documents

By Gaby Steinbach

A novel synthesis is described for the preparation of supported gold catalysts for low-temperature CO oxidation. The novel route is a variation of the inverse co-precipitation method and requires amphoteric metal hydroxides, with zinc and aluminium hydroxides chosen. Catalysts were prepared by inverse co-precipitation (ICPa) and by the novel route (ICPb) and tested for CO oxidation at 60ºC. Preliminary results showed the novel route to be superior to ICPa; the catalysts prepared by ICPb showed higher catalytic activities. The effect on catalytic activity of parameters such as pH, calcination temperature, washing of precursor and calcined catalysts and ageing was investigated. A preparation pH of 9 and a Zn to Al mass ratio of 3 proved to be optimal. It was possible to remove residual chloride by washing thereby enhancing catalyst performance. Ageing and Mg citrate addition were also shown to improve catalyst performance. Characterization of the catalysts revealed that better activities were obtained when the support was more crystalline and had a higher surface area. The presence of carbonate-containing species in the support decreased catalytic activity. 197Au Mössbauer Spectroscopy revealed the presence of Au3+ when catalysts were heat-treated at temperatures of 200ºC and below. Catalysts calcined at 400º had 75% of the gold present as Au0, with the remaining gold present as Au3+.

Oct 1, 2003

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-A1 alloys has been measured up to the solubility limit for formation of aluminum nitride using the Sieverts method. The activity coefficient of nitrogen decreases slightly with increasing aluminum content in the range of 0 to 4 wt pct Al. Based on a nitride composition, AlN, the standard free energy of formation of aluminum nitride from fhe elements dissolved in liquid iron has been determined to be: ?F" = -59,250 + 25.55 T in the range from 1600º to 1750ºC. The solubility of nitrogen in liquid iron alloys and the interaction of nitrogen with dissolved alloying elements in liquid iron have been the subject of a number of research investigations.' Most of this work, however, has been reported for concentrations well below those necessary for the formation of the alloy nitride phase. Data in the concentration region near the solubility limit of the alloy nitride, particularly for systems exhibiting stable nitrides, are important in evaluating the denitrifying power of various alloying elements. They are also useful in determining the stability of a given nitride if it is to be used as a refractory to contain liquid iron alloys. In view of the importance of aluminum as a deoxidizing agent in commercial steelmaking and the fact that its nitride, AIN, is a highly stable compound and has merited some consideration as an industrial refractory, the following investigation was undertaken. The use of the Sieverts technique provided a measurement of the equilibrium nitrogen solubility in liquid Fe-A1 alloys as a function of nitrogen gas pressure up to 3.85 wt pct A1 in the temperature range of 1600º to 1750°C. The values obtained by the Sieverts method were checked by means of a quenching method in which liquid iron was equilibrated with an A1N crucible under a known partial pressure of nitrogen gas, and the solubility of A1N in liquid iron determined by chemical analysis. EXPERIMENTAL PROCEDURE The theoretical considerations involved in determining the solubility product of a solid alloy nitride phase in liquid iron by measuring the point of departure of the nitrogen gas solubility from Sieverts law have been discussed by Rao and par lee.' The principal problem is to determine the variation of nitrogen solubility in an alloy as a function of the pressure of nitrogen gas over it with sufficient precision to establish the break point in the curve at the solubility limit of the alloy nitride phase. A fairly large number of data points are required to do this. A second problem is the determination of the composition of the precipitated solid nitride phase. This is necessary in order to define completely the thermodynamic relationships. The Sieverts apparatus used to make the nitrogen solubility measurements in this investigation is of essentially the same design as that described by Pehlke and E1liott.l The charge materials were Ferrovac-E high purity iron supplied by Crucible Steel Co. and 99.99+ pct pure aluminum. Recrystal-lized alumina crucibles were used, and were not attacked by the liquid alloys. The hot volume of the system which was measured for each melt ranged from 46 to 50 standard cu cm and was found to decrease linearly with decreasing pressure and with increasing temperature. The temperature coefficient of the hot volume at 1 atm pressure of argon gas was essentially constant for all experiments at a value of -6 X 10-3 cu cm per "C. The melt temperature was measured with a Leeds and Northrup disappearing filament type optical pyrometer sighted vertically downward on the center of the melt surface. The temperature scale was calibrated against the observed melting point of pure iron taken as 1536°C. The emissivity of all melts was assumed to be that of pure iron, taken as 0.43. The charge weights ranged from 110 to 140 g and the range of aluminum contents covered was from 0 to 3.85 wt pct. Aluminum additions were made as 12 to 15 wt pct A1-Fe master alloys previously prepared in the system under purified argon. The compositions of the master alloys were checked by chemical analysis and found to be in agreement with the charge analyses. Vertical cross sections of the master-alloy ingots were used as charge material for the equilibrations in order to minimize the effect of any segregation which might have occurred during solidification of the master alloys. Determinations of the solubility product of

Jan 1, 1964

By R. H. Kolb

A long term project at Shell Development Co.'s Exploration and Production Research Laboratory has been the improvement of the accuracy and the ease of BHP measurements. As a result of these efforts, two complete and separate systems have now been built for the automatic logging of BHP variations. The first of these is a small-diameter instrument suitable for running through production tubing on a single-conductor well cable. During the development of this instrument, as much emphasis was placed on providing a high degree of usable sensitivity and repeatable accuracy as on obtaining the advantages of surface recording. The second system combines the benefits of automatic, unattended recording with the convenience of a permanently installed Maihak BHP transmitter.' THE CABLE INSTRUMENT For many years the standard instrument for BHP determination has been the wireline-operated Amerada recording pressure gauge or one of several other similar devices. This gauge records on a small clock-driven chart carried within the instrument, and although relatively precise readings from the chart are possible, they are difficult to ob-tain. a Both the maximum recording time and the resolution of the time measurements are limited by chart size, and when a slow clock is required for long tests, the precision of the time measurement is often inadequate. Since it is impossible to determine the data being recorded until the gauge has been returned to the surface, wasted time often results when a test is protracted beyond the necessary time or when it is terminated too soon and must be re-run. Clock stoppage or other malfunctions which would be immediately apparent with surface recording remains undetected with down-hole recording; the test is continued for its full term with a consequent loss in production time. As new uses for subsurface pressure data evolved, the shortcomings of the wireline instrument became increasingly apparent, and the concurrent development of a surface-recording pressure gauge and the associated high-pressure well cable service unit' was undertaken. Description of the Instrument Because of its ready availability and advanced degree of development, the Amerada bourdon-tube element was chosen as the basic pressure-sensing device. This element converts a given pressure into a proportional angular displacement of its output shaft, and a suitable telemetering system was designed to measure accurately the extent of this displacement and to transmit the measurement to the surface and record it. The telemetering system furnishes a digital record printed on paper tape by an adding machine-type printer. The present arrangement provides a resolution of one part in 42,000 over the angular equivalent of full-scale deflection, giving a usable sensitivity of better than 0.0025 per cent of full scale. An additional refinement simultaneously records on the tape the time or the depth of the measurement, also in digital form. When the instrument is placed in operation, an adjustable programer can be set to initiate a read-out cycle automatically at selected time intervals. When subsurface pressures are changing rapidly, readings may be recorded as frequently as once every 10 seconds; when pressures are more nearly stabilized, the period between readings may be extended to as much as 30 minutes. Because the instrument is surface-powered as well as surface-recording, the maximum period of continuous logging is (for all prac. tical purposes) unlimited. The subsurface instrument is a tubular tool, 1 1/4-in. in diameter and 6.5 ft in length, operating on 12,000 ft of conventional 3/16-in. IHO logging cable. The transmitting section, mounted above the bourdon-tube element in place of the regular recording mechanism, contains no fragile vacuum tubes or temperature-sensitive transistors. This unit has been laboratory-tested to 1 0,000 psi and 300°F and has performed dependably during a number of field operations. The down-hole transmitting arrangement can be fitted to any standard Amerada pressure element, regardless of range and with no modification of the element itself. Calibration To obtain a repeatability commensurate with the sensitivity and resolution of the instrument, it was necessary to develop a special calibrating technique. The manufacturers of the Amerada recording pressure gauge claim an accuracy of only 0.25 per cent of full scale, which is a realistic figure for normal calibrating and operating procedures. An exhaustive investigation was made of the errors inherent in the bourdon-tube element, itself, independent

By Robert E. Charles

Much has been said about digital computer control of metal and mineral ore dressing processes, but little has been done. This pa- per discusses what practical use can be made today of a digital computer in an ore concentrator and how such application can be made successfully. A hypothetical, but commercially common, grinding and flotation circuit is presented in terms of analog measurements which can and are being made in existing plants and a centralized computer control system which is reasonable in terms of today's technology. Dangers and possible disadvantages of such an approach are discussed as well as estimated benefits. Possible future benefits are presented in terms of improved control technology. Development of new measuring devices is not considered as a criterion for computer benefits. The control systems described have been utilized successfully in existing ore dressing operations. However, the degree of success or failure of analog systems is generally left to the interpretation of management rather than absolute analysis. Many factors affect the economic operation of a mineral recovery circuit such as size of facility, flow sheet design, number of operating personnel, percent of recoverable mineral in the ore body, loss to tails, and haulage rates. In existing mills where little or no instrumentation has been used, it is extremely difficult to prove or disprove the advantage of analog control systems on one mill line versus its sisters due to the lack of standards and the lack of ability to separate final products by ton.

Jan 1, 1969

By G. H. Miller

With the recent advances which have been made in science and technology and the increased use of mathematics in this area, the question of the best mathematics courses for a mining engineer to take is of major importance. The question becomes even more difficult to answer due to the recent increase in the number of different mathematics courses in the last two decades offered by the mathematics departments. Therefore, the National Study of Mathematics Requirements for Scientists and Engineers (NSMRSE) was designed to provide some answers to these questions. Approximately 10,000 scientists and engineers were selected for the Study, These individuals were placed in two categories: (1) The Awards Group, recipients of national honors or awards and those recommended by the members of the Board of Advisors as having national and international reputations in their areas of specialization and (2) The Abstracts Group, persons exceptionally productive in their research, based on the number of journal articles listed in the last five years in the Engineering Index, Scientific and Technological Aerospace Reports, Chemical Abstracts, Biological Abstracts, and the Physics Abstracts. The NSMRSE Course Recommendation Form and the Instruction and Course Content Sheet were constructed with the aid of the Board of Advisors and other consultants. For the Study, 40 courses were selected by the mathematical consultants. In order to make sure that the basic content of the mathematics courses was the same for all respondents, a brief resume of each of the 40 courses was given. The NSMRSE Course Recommendation Form consisted of seven sections. These sections were as follows: Section 1, 38 different specializations; Section 2, orientation of work (applied through theoretical); Section 3, highest degree obtained; Section 4, place of employment (academic, nonacademic); Section 5, administrative capacity (administrative or nonadministrative); Section 6, age groups (five-year intervals). Section 7 contained the 40 courses which were to be marked according to five categories: (1) Course Length, 3 to 36 weeks; (2) Applied-Theoretical Orientation, a five-point scale; (3) Course Level, freshman through graduate; (4) Knowledge of Course; and (5) Use of Course Content in Work. The Analysis The report of the data is based on the replies received from 44 mining engineers. This group was part of the Awards and Abstracts Group for all engineers. The resume of the recommended courses is reported in quintiles (upper fifth to lower fifth), since recommendations of this kind are not precise. The results of the Study are based on recommendations of the most active research men in engineering in the U.S. today; therefore, the reader should realize that these course recommendations represent an upper bound of mathematics requirements for the Ph.D. in both undergraduate and graduate work. Conclusions and Recommendations 1) Mining engineering students who plan to be active research specialists should take all those courses which are "very highly recommended" (80-10070) and "highly recommended" (60-79.9%). Those courses in the upper two quintiles and recommended by most mining engineers are: first-year calculus, third-semester calculus, elementary differential equations, applied statistics, and machine computation. Courses of "moderate recommendation" (40-59.9%) are: vectors, intermediate ordinary differential equations, the first course in partial differential equations, elementary probability, and linear programming. 2) The great majority of mining engineers indicated that they prefer a course which is concerned primarily with applications. Only the standard courses such as first-year college mathematics, calculus, differential equations, and advanced calculus received a recommendation for 50% theory and 50% practice. Therefore, all mathematics courses given to mining engineers should contain many applications and little theory. Engineers in both the applied and the combination (ap-plied-theoretical) groups indicated a definite need for applications in all courses. 3) In general, recommendations were for mathematics courses to be given for short intervals of time such as 3, 6, or 12 weeks. Only the standard courses mentioned previously received the usual one-semester or one-year recommendation. Therefore, it is of value to combine several related courses into a one or two-semester course so that the mining engineering student could acquire important mathematical knowledge at an early date in order to prepare him for his research. 4) There was little use for the newer courses in modern mathematics such as the functional analysis sequence, the modern algebra sequence, and the group theory sequence. In addition, there were uniformly very low recommendations (0-19.9%) for multilinear algebra, complex variables, mathematical logic, special functions, integral equations, approximation theory, analytic mechanics, integral transforms, and geometric algebra. Therefore, these courses should be given a low priority. 5a) Comparisons among mining engineers with different backgrounds showed that the combination ap-plied-theoretical group recommended more mathematics than the applied group. 5b) There was little difference in recommendations between the administrative group and the nonadminis-trative group. 5c) Analysis of age groups showed that those in the lower age groups gave significantly higher recommendations to courses such as the first course in partial dif-

Jan 1, 1971

By D. T. McMurray

INTRODUCTION Shabanie mine, situated some 180 km east of Bula¬wayo, has been a producer of chrysotile asbestos for more than 50 years. The ore bodies occur in serpentinized dunite, which overlies talc-carbonate schist. A zone of relatively competent rock of varying thickness occurs between the schist and the ore bodies, which are gen¬erally less competent. The hanging wall of the ore bodies is economic, and the hanging-wall serpentine carries a variable subeconomic amount of fiber. It is important to note that, in general, the ore body competence is less than that of the foot and hanging-wall formations. Historical After surface operations ceased, cut-and-fill stoping was used to win ore from underground; this was success¬ful until the increasingly stoped-out area caused insta¬bility in the stope pillars and back. Consequently, dur¬ing the early 1950s, a gradual change to cave-mining methods was made, the ore being won by hand lashing in drawpoints, situated in the basement of the stope blocks, and passed through orepasses under gravity to the haulage level some 13 m below. About this time, interest was focused on the sub¬level caving method in use in Swedish iron ore mines: it was felt that it might be applied economically to the Shabanie ore bodies. Accordingly, in 1958, an experi¬mental stope block was laid out in which sublevel inter¬vals and extraction tunnel spacing were 9 m. The tun¬nels (ring drilling drives) were oriented on strike-in contrast to the Swedish system, in which crosscuts that retreat from hanging to footwall are used. The advantages of the method were quickly appre¬ciated by the operating personnel and, despite the in¬evitable teething troubles pertaining to the introduction of any new mining method, it was not long before sub¬level caving was providing a high proportion of the mill feed. The disadvantages also became apparent at an early stage, however, and, from that time to the present, continuing modifications have been made to mining lay¬outs in an effort to improve ore recovery. GENERAL DESCRIPTION OF METHOD The mine is served by a vertical hoisting shaft, in which two skips, a man cage and a service cage, provide adequate capacity for production requirements. The rock hoist is a Ward Leonard control hoist, in which two electric motors drive a common gearbox. The man winder is driven by an a-c motor. Several auxiliary shafts provide secondary egress and intake and return ventilation. Main haulage levels are above (Fig. I a and b). Blasthole fan patterns are drilled by drifters of 100 mm bore, drilling 41-mm holes; when a sufficient strike length has been drilled, a slot is cut in the upper¬most sublevel and the rings are broken into the slot. Initially, a limited tonnage is drawn, since it is essential to ensure that the hanging wall caves behind the retreat¬ing stope face. Once this has been established, maxi¬mum tonnage can be drawn, as described later in this chapter, under the heading "Draw Control." The broken rock is loaded by 0.14 and 0.20-m3 load¬ers into cocopans (rocker-dumping type of tipping truck), which are hand trammed to orepasses, discharg¬ing on the haulage where 11-t electric trolley locomo¬tives haul 3.95-m3 Granby cars to the main shaft bins. As is evident from Fig. 1, the layout is simple, the block is brought rapidly into production, there is a high degree of selectivity and flexibility, and the result is a low-cost high-productivity mining method. DEVELOPMENT Main haulages are developed at 3.2 x 3.2 m, and once the service winze connections have been completed the development of the sublevels is undertaken. The footwall drives are cut first, to obtain access to the block. These ends are of the standard section, 2.4 x 2.8 m, and from them crosscuts at intervals of 70 m are driven through the ore body to the hanging wall. These crosscuts are used to supplement the geo¬logical information previously obtained from diamond core drilling, and they provide additional and more de¬tailed data on fiber percentages and lengths, structural features, and other relevant criteria which are used to build up the geological assessment of the area and to classify it in terms of the geomechanics rock classification (Laubscher and Taylor, 1977). The crosscuts also allow the necessary orepasses to be sited conveniently so that tramming distances from the loading points are not excessive. Development Drilling Once the skeleton development has been completed, the extraction headings are developed at 2.4 x 2.4 m as shown in Fig. 1. Standard development practice is to use crews of a machine operator and his helper, equipped with air-leg mounted jackhammers, to drill rounds of 1.8 m with integral tungsten carbide tipped drill steel. The round drilled is a normal drag round, as shown in Fig. 2, but considerable attention is paid to the drilling of the perimeter holes to use effectively the

Jan 1, 1982

By J Price, M. R. Geer, H. F. Yancey

COAL mine operators recognize coal as an abrasive material, because the wear of drilling, cutting, and conveying equipment is reflected as a cost item for replacement of parts. Similarly, industrial consumers of coal experience abrasive wear on all coal-handling equipment. Operators of pulverized fuel plants are doubtless most keenly aware of the abrasiveness of coal, because under the high contact pressures developed between coal and metal in pulverizers, abrasive wear is increased many fold. Moreover, experience in operating pulverized fuel plants has demonstrated that some coals are much more abrasive than others. Hardgrove' stated that maintenance costs entailed by the wear of grinding elements is often a more important variable than the cost of the power required to pulverize different coals. Craig2 also reports that one coal may cause pulverizer parts to wear several times faster than another. It is apparent, therefore, that those concerned with pulverizing coal could profitably employ a method for estimating the abrasiveness of different coals, just as they utilize standard tests for thermal value, grindability, and ash-fusion temperature to assist in selecting the most suitable and economical coal to use in a particular plant. The objective of this investigation was to develop a test procedure that would be suitable for general use in estimating the abrasiveness of coals. However, few, if any, of the standard tests now used for evaluating the properties of coal are the product of a single investigation or the result of a single investigator's efforts. Rather, in each case, a testing procedure was devised by one investigator, used by others on a wider variety of coals, and finally refined completely as the result of the joint efforts of a number of interested people. Thus, the test procedure for estimating abrasiveness developed in the course of this work may not be refined sufficiently in its present form for general use, but it may serve as the starting point from which an acceptable test procedure can be developed. The method has been used thus far on only about a dozen coals, and there has been no opportunity to attempt a correlation between experimental results and actual plant experience. Only wider use of the procedure by other investigators and correlation with plant experience can determine to what extent the method will have to be modified to render it suitable for general application. Test Method Although the literature contains no record of an attempt to devise a method for estimating the abrasiveness of coal that could be used industrially, several investigators have tested properties of coal that are closely related to its abrasiveness. The abrasiveness of a material generally is considered to be related to its hardness, and hardness tests for coal have been employed by Heywood,' O'Neill," and Mathes. Also, the resistance of coal to abrasion, a property that presumably is related to the abrasiveness of coal, was measured by Heywooda and by Simek, Pulkrabek, and Coufalik.2 11 these investigators tested only individual pieces of coal. Since coal is a heterogeneous material having components of varying properties, tests of this type can yield results having little more than academic interest. Only a test method that utilizes a representative sample of coal can give results that are useful industrially. The abrasion tests used for various other materials have been considered for adaptation to testing the abrasiveness of coal. The tests used for metals,7-9 paving and flooring,'" and rubber," cannot be used because coal is not sufficiently abrasive.~ The present experimental work was begun before World War II and was conducted by three research fellows"'" working under a joint agreement between the University of Washington and the Bureau of Mines. After a great deal of preliminary work with a variety of apparatus and materials, a test procedure was developed which consisted of rotating a test disk 2Yz in. diam in a steel mortar containing the coal sample. The shaft carrying the test disk at the lower end and a 100-lb load on the upper end was free to move vertically. The bed of coal in the mortar was kept fluid by low-pressure air admitted through a port near the bottom of the mortar. Measurable wear on an Armco iron disk could be obtained in this test procedure, but, despite extensive efforts to eliminate them, several major disadvantages remained in this test method. First, with most coals the amount of wear on the iron disk did not exceed a few milligrams. Second, a single type of disk was not applicable for all coals. A smooth iron disk gave satisfactory results with both bituminous and sub-bituminous coals, but hardly any wear with anthracite or coke. A disk having studs or projections gave more satisfactory abrasion losses with anthracite and coke and presented no operating difficulties with free-burning bituminous and sub-bituminous coals. It could not, however, be used with caking coals because these coals formed a

Jan 1, 1952

By Ross C. Anderson, William I. Weisman

THE manufacture of anhydrous sodium sulphate or salt cake from natural deposits in the United States has been in general somewhat of a marginal undertaking. Competition from foreign sources and from large quantities of byproduct sodium sulphate produced domestically in the manufacture of hydrochloric acid and other chemicals has existed and continues. For example, most of the sodium sulphate produced is a byproduct or co-product in the manufacture of hydrochloric acid through the reaction of sodium chloride with sulphuric acid. In recent years, many manufacturers of rayon have installed equipment to recover sodium sulphate from waste spin bath liquors; today this is an important source. Before World War II large quantities of sodium sulphate were imported from Germany. In 1949 imported material from Europe again appeared on the domestic market. Natural sodium sulphate from Canada in substantial quantities also enters the United States markets. Despite this kind of competition, numerous attempts have been made to exploit various natural deposits of sodium sulphate in this country, but only a very few of these have survived economically over a period of years. One of these few operations is the plant of the Ozark-Mahoning Co. located 13 miles south of Monahans in West Texas. Several factors contributing to the successful life of this plant may be summarized as follows: 1—Geographical location. Monahans is reasonably close, freightwise, to the Kraft paper mills in Texas, Arkansas, and Louisiana; the Kraft paper industry is the greatest consumer of sodium sulphate in the United States. 2—Availability of natural gas as low cost fuel. Proximity of the natural gas fields of West Texas has been a tremendous asset, as the availability of low-cost natural gas is to all industry throughout the Southwest. 3—The nature of the deposit. The occurrence of sodium sulphate brines in southeastern New Mexico and West Texas has been very well described by Lang,' who writes that the brines are found in the Castile formation of the Delaware basin. Here weathering has altered the anhydrite so that a relatively porous gypsiferous zone overlies a dense impervious mass of anhydrite. This porous zone provides traps where percolating ground waters that have picked up soluble salts may lodge. These traps or pockets are the natural brine reservoirs exploited at Monahans. Although several hundred wells have been drilled, currently some 25 wells serve to supply brine to the plant. All are within 1 1/2 miles of the plant and are conveniently tied together by an electric power system serving electric motors driving the pumps. Having the raw material in the form of a brine which can be pumped from shallow wells makes possible much simpler and more efficient handling than if it were in form of solids. By contrast, other deposits of sodium sulphate, such as those in Arizona, Nevada, and North Dakota, are in the form of the solid minerals, thenardite and mirabilite, which present somewhat more of a mining and mineral dressing problem.' The largest producer of sodium sulphate from natural sources in the United States is at Searles Lake, Cal., and there a brine also is utilized. 4—Water. Substantial quantities are needed for cooling towers and for operation of gas engines. An area underlain with brine is not a promising source of fresh water, but fortunately, after a long search, an adequate supply was found nearly two miles from the plant. It may be appropriate to discuss briefly the grades of sodium sulphate offered on the market. Salt cake is the name usually applied to the grade of sodium sulphate used by the Kraft paper industry. It may be a low analysis byproduct, 95 to 97 pct sodium sulphate, with as much as l 1/2 to 2 pct residual acid, or it may be a natural product. Usually salt cake is considered a low grade product, but a great deal of a higher grade of material is marketed under this name. The specifications for glassmakers' salt cake are somewhat higher than those of the paper industry, usually requiring 98 pct sodium sulphate. Technical anhydrous sodium sulphate is a high grade material and usually exceeds 99 pct sodium sulphate. It finds the biggest market in the textile industry and is used as a builder in some synthetic detergents. Glauber's salt, Na2SO4. 10H20, is usually of high purity. Preferred for some uses, it normally has been recrystallized from an anhydrous salt. A unique manufacturing process has been developed at Monahans. This process results in the production of an exceptionally high grade of salt cake, and qualifies for nearly all uses, including many which specify the technical anhydrous grade. All of the finished product, which is very white, passes a 10-mesh U. S. Standard screen, and is retained on a 200-mesh U. S. Standard screen. It is over 99 pct Na2SO4 with main impurities being sodium chloride and magnesium sulphate. Iron content is less than 0.01 pct. As mentioned, the raw material at Monahans is a brine drawn from wells. Attention was first attracted to this location because a so-called alkali

Jan 1, 1954

By D. H. Gieskieng

THE advent of curved jaw crusher wearing plates made an approach other than segmental layout analysis desirable for prediction of capacities. For some time it had been known that the drawing board capacities of crushers using these plates had to be considerably modified by complicated experience factors to achieve agreement with results. Because these apparent capacities could be readily increased severalfold by minor crushing chamber shape changes, it was necessary that the utmost precaution be taken in predicting capacities of jaw plates modified for nonchoking, special wear characteristics, or any other reason. To this end the laboratory and field tests outlined by the author in a previous paper1 were made on Blake-type jaw crushers. The results of these tests were summarized in a simple first degree equation applicable to crushers using either straight or curved jaw plates. This equation first outlines the maximum capacity potential of a given crusher, then reduces this figure in accordance with installation circumstances by means of a realization factor. It was found subsequently that this equation, with the addition of an eccentric throw factor, is applicable to standard types of single-toggle or overhead eccentric jaw crushers as far as maximum capacity potential is concerned. However, these crushers have realization factor curves somewhat different from those outlined for the Blake type. While this paper is concerned principally with standard type single-toggle crusher capacities, the evaluation of data obtained with these machines is simplified by comparative reduction to the 10 x 7 in. Blake-type equivalents upon which the summary of the preceding paper was made. Convertibility of data from one type of crusher to the other also tends towards confirmation of both. The agreement of these data is sufficient to be considered complimentary. Consequently the feed factors, f, previously reported for Blake crushers are slightly adjusted to an average with the single-toggle crusher results. Blake-type equation: C = f.d.w.y.t.n.a.r [I] Single-toggle type equation: C = f.d.w.y.t.n.a.e.r [21 where C is the capacity in short tons per hour through the crusher, f is a feed factor, dependent upon the presence of fines in the feed, and the surface character of the jaw plates used. Values of f : Smooth Plates Corrugated Plates With normal fines 0.0000414 0.0000319 Fines scalped out 0.0000368 0.0000252 Large pieces only . 0.0000312 0.0000215 d is the apparent density of the broken product in pounds per cubic foot. (If the true specific gravity of the feed is known, 40 pct voids may be assumed and d becomes 37.4 times sp gr). w is the width of crushing chamber in inches. y is the openside setting of the crusher, in inches. In the case of corrugated jaw plates it is measured from the tip of one corrugation to the bottom of the valley opposite. t is the length of jaw stroke in inches at the bottom of the crushing chamber. It is the difference between open and close-side settings. n is rpm, or crushing cycles per minute, a is the nip-angle factor. It is unity for 26" and 3 pct greater for each less nip-angle degree. A nip-angle of 20" has an a value of 1.18, and an angle of 30" has an a value of 0.88, see Fig. 1. r is the realization factor. It is unity for perfectly uniform choke feeding and usually less for actual operating conditions according to the method of feeding used and the probabilities of hang-ups involving the size of feed and crusher opening. Approximate values are given by the curves in Fig. 2. These values are further reduced by intermittent feeding, e is the throw or diameter of gyration of the single-toggle crusher eccentric in inches. As evident in Fig. 1A, variation of feed size will generally have little effect on nip-angle if both jaw plates have flat areas. Jaw plates having continuous curvature, as in Fig. 1B will have different nip-angles, depending upon the size of feed. For test work as described in this paper this effect was accounted. For general compilation of capacities for average feeds it is suggested that the nip-angle be taken at the various settings computed, at an arbitrary level, such as is indicated in Fig. 1C. Data Evaluation To bring the Blake and single-toggle type crusher capacity test results to common terms for evaluation, all data are converted to terms of 10 x 7 in. Blake-type performance at conditions of 100 lb per cu ft, 10 in. chamber width, 250 rpm, 0.65 in. stroke, 3-in. openside setting, and 18° nip-angle. (The nip-angle of the 10x7 in. Blake is 18° at 3-in. setting.) The single-toggle crusher performances are also divided by the eccentric throw to bring this effect to unity. As outlined,' laboratory and field tests made on Blake-type crushers ranging from 10 x 7 in. to 60 x 48 in. were summarized along the foregoing conditions of speed, stroke, etc. This resulted in groups of data which correspond to feeds with fines, feeds

Jan 1, 1952

By L. T. Larson

The spectral reflectivity of zirconium in light of 441 to 668 nanometers (nm) wavelengths and air immersion has been determined. Bireflectance and apparent-angle -of-rotation measurements show zirconium to be optically isotropic when examined in light of approximately 484 nm wavelength. There is a direct relationship between bireflectance and the tilt of the basal pole of zirconium from the surface normal. This relationship allows the determination of the spatial orientation of the basal pole of an individual single crystal within a coarse-grained poly crystalline section to within± 2 to 3 deg for angles of basal pole tilt from 0 to 90 deg. In recent years considerable attention has been given to the quantitative determination of optical properties of opaque minerals by use of vertically incident, plane-polarized light. In particular, Cameron' and Cameron et a1.2 have developed criteria for the identification of a large number of anisotropic ore minerals based upon measurement of the apparent angle of rotation and the ellipticity or phase difference of the reflected light. It was shown by Larson and Pickle-simer3 that apparent-angle-of-rotation measurements may also be used to determine crystallographic orientations of grains of noncubic metals. In particular, it was shown that the basa.1 pole orientation in space of zirconium grains can be determined to ±3 deg for those grains with basal pole tilts of 10 to 90 deg from the plane of the section. Another, even more widely studied, optical property is reflectivity. cameron4 has commented upon measurement of the reflectance of plane-polarized, vertically incident light and Bowie and Taylor5 have made such measurements an integral part of their system of ore-mineral identification. Leow6 has reported on the spectral reflectivity of molybdenite and has used reflectivity values to calculate refractive indices and absorption coefficients. Cameron7 has made use of reflectivity values to ascertain aniso-tropic ore mineral symmetry and Piller and v. Gehlen8 have evaluated sources and importance of errors in reflectivity measurements as applied to calculation of optical constants. cambon9 has shown that reflectivity measurements using vertically incident, plane-polarized light are useful in the investigation of metals and in the identification of phases present in alloys. Bronson10 has made preliminary measurements on the optical anisotropy of beryIlium and Mott and Haines11 have published qualitative data on the intensity of light reflected from sections of bismuth, tin, and aluminum when these metals are microscopically examined under crossed polarizing plates. Koritnig12 has correlated the reflectivity of homogeneous solid solutions with their chemical compositions. From the above work and investigations in progress by this author, it is apparent that accurately determined values for the reflectance of vertically incident, plane-polarized monochromatic light from carefully polished surfaces of noncubic metals can prove useful in identification, composition determinations, and crystallographic orientation applications. Finally, reflectivity values, when measured in two media of differing refraction index and related to standards whose spectral reflectivities in these media are known, can be used to calculate optical constants such as refractive index and absorption coefficient. These constants may prove of use to those concerned with problems of electron band configuration. This paper reports the spectral reflectivity of zirconium measured in light of 441 to 668 nanometers (nm) wavelengths and air immersion. It also gives maximum bireflectance values for a prism section of zirconium in these wavelengths and shows how bire-flectance may be used to determine the crystallographic orientation of zirconium single crystals. Because of the lack of information on the reflectivities of the standards in oil immersion, no attempt is made to calculate the refractive indices or absorption coefficients although it is recognized that such values may be of fundamental importance. METHOD Single crystals of zirconium were cut by electro-discharge machining from a single-crystal rod grown from iodide bar by an electron-beam zone-melting process.13 The crystal sections were mounted in cold-setting epoxy resin and mechanically polished to a plane, uniform, bright surface. Each crystal was then chemically polished in a 26/26/43/5 mixture (by vol) of water, nitric, lactic, and hydrofluoric acids to remove the mechanically damaged and smeared surface layer. Final polish was obtained by electropolishing at 30 v in a bath of methyl alcohol and perchloric acid (98/2 by vol) at -70oc.14 Reflectivity measurements were made using a photometer system designed and developed at Oak Ridge National Laboratory and described in detail by Larson.15 Briefly, the reflectivity measuring system consists of a reflecting microscope; a double-beam, null-balancing photometer array; a mechanically driven microscope stage; and a direct X-Y readout of the reflectivity of the specimen relative to its orientation on the microscope stage. The measuring photometer receives its signal from the specimen through a slotted Wright occular placed on top of the photovisual head of the microscope. The reference photometer receives light through a flexible glass "light pipe" from a mirror in the reflecting system of the microscope. Monochromatic light is attained through use of interference filters (15-nm half-peak width pass bands) placed in front of a stabilized Vickers 12 v, 100 w, tungsten-filament, quartz-iodide lamp.

Jan 1, 1970

By A. K. Mukherjee, J. E. Dorn, J. D. Mole

Investigations were carried out on the effect of polyslip on the strain hardening of aluminum single crystals. The orientations investigated were those lor which the tensile axis was in the [001], [111], [112], and [012] directions plus another for which the Schmid angles for {111}(110) slip were 1 deg. The experimental data were analyzed on a model based on the intersection of dislocations with particular emphasis on the effect of polyslip on the activation volume for inter-section. It is shown that the rate of strain hardening inreases for those orientations wherein attractive dislocation intersections occur and that those orientations which produce the greater number of such intersections exhibit the greater strain hardening. Good correlation of the data is obtained with the concept that attractive junctions, as proposed by Saada, Play an important role in accounting for the rate of strain hardening. EXISTING concepts on the nature and cause of strain hardening in fcc metals have been deduced principally from experiments on the deformation of single crystals under single slip. The effect of crystal orientation on the shapes of the stress-strain curves for single slip have been summarized by seegerl and more recently by Clarebrough and Hargreaves.2 Tensile specimens whose axes fall near the center of the [001]-[011] line of the standard triangle of the stereographic projection exhibit the longest range of easy glide (Stage I) and the lowest rates of linear hardening (Stage 11) whereas specimens whose axes lie near fie [001]-[111] line of the standard triangle have limited or no easy-glide range and exhibit somewhat higher linear strain-hardening rates. Specimens whose axes lie near the [001] or the [ill] poles do not exhibit easy glide and have the highest rates of linear hardening. Kocks3 has shown that the highest rates of linear hardening Occur under Polyslip when the tensile axis coincides with the [111] or the [ 001] pole. Since the rate of strain hardening is sensitive to specimen orientation and the incidence of polyslip, these relationships might help to discriminate between various dislocation models for strain hardening in fcc metals. Previous attempts to analyze the effect of orientation on strain hardening,1"3 however, did not provide a unique answer to this problem. Consequently the present investigation was undertaken wherein additional data, particularly that for the effect of polyslip on the activation volume for intersection, was also determined in order to provide more complete information on the details of strain hardening. Whereas analyses of these data reveal that several recommended models for strain hardening are at variance with the facts, good correlation of the data is obtained with the concept that attractive junctions4 play an important role in accounting for the rate of strain hardening. I) EXPERIMENTAL APPROACH seegerl demonstrated that slip in fcc crystals at low temperatures is dependent on thermally activated intersection of glide dislocations with forest dislocations. This has been confirmed by tests on single crystals of aluminum by Mitra, Osborne and Dorn5 and on polycrystalline aluminum by Mitra and Darn.' Thus in accord with Seeger's theory, the shear strain rate, ?, below a critical temperature, T, is where .V is the number of points of contact per unit volume between forest dislocations and glide dislocations, A is the area swept out per successful intersection, b is the Burgers vector, v is the frequency of vibration of the segment of the glide dislocation undertaking intersection, U is the activation energy for intersection, k is Boltzmann's constant, and T is the absolute temperature. For aluminum, which has an extremely high staeking-fault energy, the constriction energy is negligibly small and therefore the activation energy decreases practically linearly with the stress according to as will be recomfirmed later, where Uo is jog energy at the absolute zero, G and Go are the shear moduli at the test temperature T and O°K, respectively, L is the spacing of the forest dislocations, t is the applied shear stress for slip, and tGo is the stress field that must be surmounted athermally.

Jan 1, 1965

By P Staples, G Lane, S Morrell

The design of semi-autogenous grinding (SAG) mill based comminution circuits for the treatment of competent ores, similar to those at Geita and Boddington, involves the same process of sample selection, test work, data analysis and data modelling/interpretation as that used for 'average' competency ores. However, over the past couple of years a number of issues have arisen that are common to the design of circuits for the comminution of 'highly' competent ores. The impact of these issues on project viability is generally more pronounced when treating hard ores than average to soft ores due to the greater impact on capital and operating costs. The issues encountered have included: standard test procedures have been modified; test equipment has worn or been damaged; different procedures yield different data and varying interpretation; and modelling and empirical calculations have been based on poor benchmarks, or used incorrectly in the case of JKSimMet, yielding misleading outcomes. The purpose of this paper is to present, discuss and clarify some of the issues associated with conducting test work and designing comminution circuits for the treatment of 'highly' competent ores in order to reduce thelevel of conflict arising from interpretation and application of test work data. Specifically, the issues associated with the bond crushing (impact) and rod work indices measurement, the various SAG mill specific energy tests, and the interpretation of the resulting data will be discussed in the context of case studies.

Jan 1, 2009

By H. J. Morel-Seytoux

Methods of predicting the influence of pattern geometry and mobility ratio on water flooding recovery predictions are discussed. Two methods of calculation are used separately or concurrently. The analytical method yields exact solutions in a convenient form for a unit mobility ratio piston-like displacement. A few typical pressure distributions, sweep efficiencies and oil recoveries are presented for various patterns. For non-unit mobility ratio, one may resort to a numerical method, such as that of Sheldon and Douherty. 1,2 Because the domains of applicability of the analytical and numerical techniques overlap, the exact solutions provide estimates of the errors in the numerical procedures. The advantages of the analytical and numerical methods can be combined. To develop a numerical technique as independent of geometry as possible, the physical space is transformed into a standard rectangle. The entire effect of geometry is rendered through one term, the "scale-factor", derived from mapping relations. The scale factor can be calcu-lated from the exact unit-mobility ratio solution for the particular pattern of interest. By this means recovery performances for arbitrary mobility ratio con be obtained for many patterns. A sample of tesults obtained in this manner is presented. INTRODUCTION Pattern geometry and mobility ratio are two major factors in making a waterflood recovery prediction. Because assisted recovery has become increasingly important to the oil industry, pattern configuration and mobility ratio also assume a greater significance in the assessment of the economic value of recovery projects. The influence of pattern geometry and mobility ratio in shaping a recovery curve and on the other quantities of interest to the reservoir engineer is the main subject of this paper. Much effort has already been spent on estimating quantitatively the influence of either pattern or mobility ratio or both on oil recovery. The literature reports many investigations of this nature. 3-9 However, many results or methods of recovery prediction presented in the literature cannot be considered fully satisfactory. Even for unit mobility ratio and piston-like displacement, where analytical solutions are available, the literature shows discrepancies. For non-unit mobility ratio, the divergence in the results is extreme. For infinite mobility ratio in a repeated five-spot, depending on the investigator, the sweep efficiency ranges from 0 per cent to 60 per cent. With respect to the influence of pattern on recovery, only the repeated five-spot has received much attention. Other confined patterns and pilot configurations have received very little attention. Two calculation methods are presented in this paper, either separately or concurrently: the analytical method of potential theory and the numerical method of finite-difference approximation. The analytical method is more restricted in scope than the finite-difference method, but it has the definite advantage of providing exact solutions within its range of applicability. If a unit-mobility ratio piston-like displacement is assumed, the analytical approach is possible. A few typical results are reported in this paper; the detailed description of the general method and of a great variety of results will be the subject of other articles. Fornon-unity mobility ratio, we must resort to a numerical scheme. The numerical technique is that which was described by Sheldon and Dougherty.l,2 It is not limited to piston-like displacement. However, mainly single interface results will be presented here. Because the respective domains of applicability of the analytical and the numerical method overlap, useful comparisons of exact and numerical solutions can be made for a variety of patterns. The advantages of the analytical and numerical approaches can be combined. The reason for the success of this analytical-numerical approach can be summarized in the following two points: 1. The numerical solution for arbitrary mobility ratio can be programmed most efficiently when the physical space in which the displacement actually takes place is transformed into a standard shape; and 2. This can be done with remarkable simplicity whenever an analytical expression for the pressure

Jan 1, 1966

By M. S. Safarzadeh

Over the last fifty years, the treatment of enargite concentrates has not received much attention primarily because of the availability of other clean concentrates suitable for processing with existing smelting and/or leaching technologies. As traditional copper ores have become scarcer, copper-arsenic ore deposits have garnered more interest. Arsenic release is a significant concern during the treatment of enargite by pyro or hydrometallurgical methods. Enargite is also very refractive in standard leaching procedures. Thus, economical treatment options for enargite concentrates are needed. Preliminary experiments have shown that the acid-bake leach process could be adapted and used for the treatment of enargite concentrates. In this study, low-temperature (100-400 ºC) sulfuric acid baking of an enargite concentrate followed by water-leaching has been evaluated. The results indicate the thermal transformation of enargite to copper sulfate during sulfuric acid baking, with most of the arsenic being released from the concentrate into the gas phase for baking at 400 ºC. The condition for maximum copper extraction (~100%) from the concentrate was found to be 400 ºC, sulfuric acid amount of 0.5 mL/g of concentrate, and 2 h baking time. Part of the arsenic was captured in the form of arsenopyrite (FeAsS). XRD analysis proved the presence of some arsenic in the form of claudetite (As2O3) in the baked concentrate. Acid baking of pure enargite behaved in similar fashion.

Jan 1, 2012

By Rajamani R. K.

The design of tumbling mills has progressed from the Bond work index concept of the 1950s to the population balance concept of the 1980s and then made a quantum leap forward with the discrete element method in the 1990s. The failure of a SAG mill at the Grasberg mine site set in motion the inquiry into the role of shell lifter geometry on the profile of the charge motion within the mill. Quickly, it became evident that this could only be accomplished by tracking individual motion of ore particles and grinding balls and not by study of en masse motion of the charge that had been established previously. The discrete element method (DEM) which was prevalent in the civil engineering literature at that time proved suitable to tackle this simulation problem. In 1991, the two dimensional simulation of laboratory scale mills was validated with the DEM. Later this simulation method evolved into ?MillSoft?? a simulation software package for the design of lifters in ball and SAG mills. MillSoft?simulations proved that cataracting charge motion is not conducive to the life of lifters. The old rule of thumb that the number of shell lifter rows should equal twice the diameter of mill in feet was shattered by simulation results. Instead, the number of rows equal to the diameter of the mill in feet, providing that the lead angle of lifter is around 25 degrees, was established as being more optimal. This bold design change was first implemented and tested by Mark Sherman at Alumbrera Mines in Argentina. Two 36-ft SAG mills responded extremely positively to the design change. This success was immediately repeated at Collahuasi, Pelambres and other mines in South America. The design change has so far exceeded expectation that there is not a single SAG mill around the world today that does not employ a relief angle on its shell lifter. The DEM method has advanced in the hands of the author, mining companies and universities, notably in Australia and South Africa. Today, three-dimensional simulation of charge profile and slurry transport is a standard in the design of mills. There is strong pursuit of a virtual comminution machine with DEM in Australia. In South Africa, an experimental method known as positron emission tracking is emerging as a method for tracking particles in grinding mills. The computational burden of computing with millions of particles in three-dimensional simulations has been eased to less than a day with a technique known as GPU computing. Keywords: DEM method, GPU computing, SAG mill, tumbling mill simulation, discrete element method

Sep 1, 2012

By Liu Wei

In order to make clear the dissolving characteristic of the chrysocolla (CuSiO3?H2O) in the ammonia-ammonium chloride solution, a thermodynamic model of the chrysocolla (CuSiO3?H2O)-ammonia- ammonium chloride-water system is established using the exponential computation method based on both mass balance and charge balance equations. The equation group of the thermodynamic model is solved by the MATLAB Soft on PC. The condition which is favorable for dissolving high concentration of copper in solution is making out. The stable area of chrysocolla (CuSiO3?H2O) and the condition of chrysocolla (CuSiO3?H2O) converting to atacamite (Cu(OH)1.5Cl0.5) is also studied. A group of experiments are designed to validate the veracity of the results of the thermodynamic calculation.

Jan 1, 2010

By Zhou Wenbin

In this paper the mechanical properties of high carbon equivalent cast iron for automobile brake discs were analyzed through thermal analysis curves. Experiment results show that the mechanical properties have a strong correlation with thermal analysis curves and an effective way to predict the mechanical properties of high carbon equivalent cast iron was proposed based on the features of thermal analysis curves.

Jan 1, 2010

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By Ailton da Silva Ferreira

Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of curaua fibers. Both TGA and DTG curves were analyzed to determine the effect of the curaua fiber on the thermal resistance of the composites. It was found that the curaua fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.

Jan 1, 2010

By Rameshwar Sreenivasan

This paper presents a sustainability analysis of Selective Laser Sintering (SLS) from an energy standpoint. Data of electrical power consumed by the system over an entire build were acquired using a LabVIEW 8.6 circuit. The power drawn by individual subsystems was also measured, and an energy balance was performed. These data were then used to arrive at a Total Energy Indicator of the process with the help of a specific type of Environmental and Resource Management Data (ERMD) known as Eco- Indicators, which indicates the level of sustainability of the process.

Jan 1, 2010