Search Documents

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018

By G Byrne

Long-term water management is typically ignored in mine closure planning. A review of 73 mine closure plans dating from 2007 to 2013 shows that, on average, relinquishment is proposed to be achieved in 11 years. A separate review of 57 mines in actual closure shows that only five have so far achieved relinquishment with an average closure period of 14 years after production cessation. The remaining 91 per cent of sites in closure have an average closure duration to date of 21 years - and still going.A common issue among those sites in closure is water management, with a further common issue being acid and metaliferous drainage (AMD). Of the closure plans that were reviewed only one site had allowance for long-term (&gt;50 years) of water treatment. Of the sites in actual closure 25 per cent have reported that they expect such long-term water treatment, with many acknowledging that in perpetuity treatment is probable.Clearly there is a gap between what is being allowed in closure plans and the reality of closure. There are a number of factors leading to the optimism of the closure plans, including unrealistic assumptions, pressures to reduce closure cost provisions and the technical complexity of many AMD issues.Long-term water management is a reality that needs to be acknowledged and addressed. If addressed early in the mine life cycle the impacts for mining companies can be reduced.CITATION:Byrne, G, 2013. Long-term water management - the forgotten legacy of mine closure, in Proceedings Water in Mining 2013 , pp 163-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By H. J. Heinen

The Bureau of Mines, investigated a cyanidation-carbon adsorption technique for extracting gold from arsenopyrite concentrates. Agitation leach experiments were conducted on 85-pct-minus-35-mesh gravity concentrates containing 21.8 oz gold and 6.4 oz silver per ton. Results obtained in leaching the concentrates showed that 96.9 pct gold and 90.7 pct silver extraction could be achieved in 96 hours of agitation. Gold and silver were recovered from the resulting pregnant solution by exposure to granular activated carbon in a countercurrent system. Carbon loadings of 2,556 oz of gold and 502 oz of silver per ton were achieved. These loadings are significantly higher than heretofore thought practical.

Jan 1, 1980

By Mustafa Akser

Dwindling economic deposits of rutile (TiO2) prompted research on recovering it from secondary sources. One such resource is in Southwestern Turkey feldspar mining rejects that contain 5%-6% TiO2 mostly rutile. Previous studies could only upgrade the TiO2 to 36% TiO2 grade, claiming that the leftover flotation reagents on the surfaces of rutile and host minerals detrimentally affected upgrading of the rutile. As a potential remedy to this concern, a laboratory sample (from an operating feldspar mine in Milas, Turkey) was first caustic scrubbed, then air calcined at 400°C to evaporate the oily reagents. Subsequent physical separation of rutile included wet screening, gravity, magnetic, and electrostatic separation technologies. Such processes indeed improved the grade of the rutile concentrate up to 83 % TiO2 Low recovery of the TiO2 (<20%), was attributed to lack of full liberation of rutile, even at 125x44 micron range; interference with impurity minerals such as sphene and zircon; and simply the process inefficiency in upgrading the fine grains through conventional separation technologies for heavy minerals.

Jan 1, 1999

By S. K. Sharma

The Bureau of Mines&apos; Tuscaloosa Research Center is conducting research to develop a basic understanding of solid-liquid separation in order to improve the dewatering of fine particle slurries. In the present investigation capillary suction time (CST) of kaolin slurries was determined. The average specific resistance of the cake was also determined by fitting the CST data to the theoretical equations used in this paper. The experimental data were analyzed by a powerful computer-based method, chemometrics, that uses statistical techniques to remove error and to find the number of physically significant factors contributing to the data. Results showed that two significant factors explain the CST data.

Jan 1, 1991

By Hsing Kuang Lin

Ferric chloride leaching w.as applied to a complex sulfide ore from Tok, Alaska to dissolve zinc, lead, silver and copper. Gold in the leaching residue, as well as in the ore, is found to be refractory to the conventional cyanidation process. Roasting, pressure oxidation and elemental sulfur removal followed by cyanidation were tested to improve gold dissolution. Also tested were thiourea leaching and high-pressure cyanidation. The readsorption of dissolved gold by carbonaceous matter in the chloride leaching residue was analyzed. Based on the experimental results, factors causing difficulty of gold dissolution from the leaching residue are discussed.

Jan 1, 1989

By R. L. Hopkins

Fifteen alkyl cycloalkyl sulfides and three dicycloalkyl sulfides were synthesized to provide reference compounds in the search for these classes of sulfur compounds in crude oils. In synthesizing sulfides by alkaline alkylation the order in which the reactants were added was shown to determine the yield and purity of the product.

Jan 1, 1966

By Xiao Jian Li, Dai Xiong Chen, Jian Wen Yang

In one kind of lead and zinc bearing polymetallic ore containing secondary copper, the characteristic of low sulfur, high zinc, and particularly the existing of secondary copper minerals can lead to lead concentrate with high content of zinc because the dissociation of Cu2+ in the grinding process may have an activation influence on sphalerite. Considering its process mineralogy analysis, a new process of seperation of lead and zinc has been put forward. The experiments focused on the analysis of the advantages and disadvantages of the inhibition effect of traditional adjustment reagent + zinc sulfate on activated sphalerite compared with new organic inhibitor, polysaccharide xanthate. According to the numerical calculation and test results, a reagent system of polysaccharide xanthates is developed, which has a good inhibition effect on Cu2+ activated zinc minerals, achieving high-efficiency separation of lead and zinc. A new reagent system and flotation process was developed under optimal conditions. Under the condition of the run-of-mine ore containing 2.37% Pb and 12.48% Zn, lead of 67.69% grade and lead concentrate with the recovery rate of 86.06%, zinc of 60.32% grade and zinc concentrate with the recovery rate of 96.15% were achieved.

Jan 1, 2014

By Chas. F. Jackson

This paper is a tabular compilation of data contained in a series of information circulars dealing with mining methods and costs at a large number of mines in the United States and some foreign countries. There circulars have been published from time to time during the years 1929 to 1934 inclusive. From time to time, as enough data became available in these circulars, other circulars and. bulletins have been published in which the data bearing upon different phases of nine operation were summarized, discussed, and analyzed. The present paper is a compilation of data on costs of drifting and crosscutting contained in earlier circulars, .designed to assemble this information in a convenient form for reference without attempting lengthy discussion of details of drifting and crosscutting practice. For such details the reader is referred to the circulars on individual mines.

Jan 1, 1935

By Magnus Evertsson, Haijie Li, Erik Hulthen, Mats Lindqvist

"The static and dynamic models for autogenous (AG) and semi-autogenous (SAG) mills have been studied for decades. Though the effects of mixing soft and hard ores in a mill and their interactions are not widely investigated. To develop a general numerical model for AG/SAG mills, a dynamic model has been introduced, and its capability to simulate multi component ore breakage has been examined and compared with previous publications. The simulation results show that the dynamic model can cover a range of milling conditions and is able to simulate complex scenarios with soft and hard ores. The dynamic model discussed here could provide substantial potential for the controlling and optimization of the comminution circuits. INTRODUCTION In the last decades, efforts have been devoted to studying the comminution circuit due to their high energy consumption. The energy directly spent in minerals comminution was about 2% globally in the year 2000 (Maurice et al, 2003). As one important part of the comminution process, AG/SAG mills are widely used for primary grinding in minerals processing. AG/SAG mill models include static and dynamic models (Kojovic et al, 2012; Yu et al, 2014; Yu et al, 2017; Liu and Spencer, 2004; Salazar et al, 2009). Many static models have been well validated over the past decades, but they are all based on steady state assumptions. Even though plants experience a steady-state condition under certain circumstances, it can be inaccurate to simulate the system by static models under all circumstances (Asbjörnsson et al, 2013). The advantages of a dynamic model are apparent that it provides more information and insights both inside the mill and through interactions with other machines in terms of pebble crushers, conveyor belts, screens and so on. In many mines, the multi-component grinding is inevitable, and the ratio of hard and soft components in the mill strongly affects mills operation and performance. Bueno (Bueno et al, 2010; Bueno et al, 2013) studied the effects of blending hard and soft ores in AG/SAG mills and used them to update the JKSimMet toolkit which was a steady state plant simulation software. However, due to the complexity of the particle interactions such as multi-component breakage function, appearance function, in mill transportation, there has been no dynamic AG/SAG mill models developed yet for simulating multi-component."

Jan 1, 2018

By Martin S. Oudenhoven

This Bureau of Mines report presents the results of a microseismic study conducted in the Climax block cave mine at Climax, Colo. Rock noises created by caving were monitored and their sources located during a 3-month period. A planar array of seven accelerometers, located above the block of ore being caved, detected the rock noise. A computer was used to calculate the location of the microseismic activity, using a traveltime difference method. The accuracy of these locations was estimated to be ±20 feet. An analysis of the data taken during the recording period showed a concentration of microseismic events located in the wall of the cave panel. This concentration of events was found to occur in a "high-silica" geologic forma-tion that cut across the caving panel approximately 200 feet behind the undercut.

Jan 1, 1973

By U. S. Chattopadhyay

The estimated requirement of the nation by the year 2020 is approx. 80 Mt of steel and more than 0.2 million MW installed capacity of the electricity, thereby increasing the consumption of the coking and non-coking coal, which is expected to be in tune of about 75 Mt & 500 Mt respectively. One of the major deleterious factors in achieving the goal is the deteriorating quality of the feed coal used in both steel and power industries. Indian coking coals, in general, are typified by high ash, high inert (both organic and inorganic), low rank, low reactive macerals content, heterogeneous petrographic make-up, inferior coking properties and poor amenability to washing, thereby necessitating suitable washing measure. Coke-based steel industries in India require washed coking coal containing ash % varying between 17-19. The situation demands taking on immediate challenges to fill up the gap between the requirements and supply of coking coal. This paper reviews the R&D attempts in this laboratory and throws light on the key measures as long-term solution to the problem. Search for alternative source of coking coal, like LVC coal and their judicious preparation technology. The low volatile coking coal (LVCC) constitutes about 50% of the total coking coal reserves in India. These coals are characterized by high raw coal ash content (37 to 40%) and very difficult washability potential. If these coals are treated in the existing washeries, which are generally 2 or 3-product systems, the cost of clean coal is high as the byproduct sale value is low. It has been proposed to produce a new type of by product, which enjoys high demand and good coking properties.

Sep 1, 2012

By Bradford P. Simser

The theoretical capacity of various ground support components can be misleading, especially in bursting ground where the failure mode is often in the retainment system. Wire mesh screen seams often peel open rather than breaking the wire strands, fractured rock often un-ravels around the bolts rather than breaking the bars. If a weak link(s) in the system fails prematurely, then the potential capacity of the system may never be fully realized. Underground observations are used to show how some support systems behave in the field. Various combinations of wire mesh screen with friction bolts, rebar, modified conebolts, cablebolts, shotcrete and mechanical rockbolts are considered. A short case history is used to contrast the performance of ?just-intime? development in a high stress faulted area versus a tunnel subjected to multiple stress changes in a similar environment. The latter proved to be a serious ground support problem when the well developed fracture zone around the opening was subjected to dynamic loading from a large seismic event causing a severe rockburst. In such cases an improved mining strategy may be more relevant than higher capacity support systems.

Feb 1, 2008

By N. S. Dalal, X. Shi, V. Vallyathan

"Electron spin resonance (ESRJ spectrum of the hydroxyl (· OH) radical spin adduct with .the spin trap 5,5-dimethyl-1-pyrrolintt-N-oxide has been obtained in suspensions of freshly ground quartz particles. The concentration of the spin adduct (and hence of the • OH radicals) increases with the amount of grinding. The dust's potential for the generation of the· OH radicals is maximum when fresh (i.e., immediately after grinding) and decreases to 50% in about a day on storage in air. Studies involving metal chelates .indicate that the • OH radical formation involves mainly the silica surface and H20 rather than the Fenton reaction. The results suggest that hydroxyl radical reaction(s) could be important in the lipid peroxidation and fibrogenicity by quartz dust, particularly .in acute silicosis. INTRODUCTIONIn this paper we report on our electron spin resonance (ESR) detection of the formation of hydroxyl (·OH) radicals in aqueous suspensions of freshly crushed quartz particles. This work was undertaken with a view to find possible clues to the role of free radicals in the pathogenesis of quartz-induced fibrogenicity, commonly known as silicosis. We noted that while silicosis is one of the major health hazards in coal and mineral industries, the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still poorly ·understood (Reiser and Last, 1979; Singh and .Rahman, 1987). It is generally thought, nevertheless, that the action of quartz particles on the biological membranes is the starting point of the silicotic process (Parazzi et - al., 1968). A possible clue to the mechanism of the membrane damage by quartz particles, in terms of the role of oxygenated free radicals, is suggested by the following observations. A suspension of quartz particles in contact with alveolar macrophages has been reported (Gabor et al., 1975; Koike et al., 1982) to initiate an enhancement of lipid peroxidation, defined broadly as the oxidative deterioration of polyunsaturated components of lipids. Hydroxyl (· OH) radicals are known to be capable of peroxidation by abstracting hydrogen atoms from cell-membrane lipids (Halliwell and Gutteridge, 1985) and of initiating lipid peroxidation in lysosomal membranes. (Fong et al., 1973). Arong other lines, it is known that exposure of cell membranes, fatty acids, and unsaturated food oils to ionizing radiation, which generates· OH radicals, causes rapid peroxidation (Halliwell and Gutteridge, 1985). Thus • OH radicals (and also other oxygenated species such as Oi, 10 2, and H20 2) might be expected to play a role in the toxicity of quartz. Earlier studies of the aqueous chemistry of quartz suspensions have reported detection of H2O 2 (Kalbanev et al., 1980), implicating the formation of ·OH radicals as transient species. However, we are not aware of any report of the detection of • OH radicals in quartz reactions, and thus the present study was undertaken. Since it-is known that, because of their high reactivity (hence short lifetime) in aqueous media, the • OH radicals cannot be detected via ESR directly (Finkelstein et al., 1980; Buettner, 1982) we have used .ESR combined with the spin-trap methodology (Finkelstein et al., 1980) for studying the· OH formation. The results show that· OH radicals are indeed formed in aqueous suspensions of freshly ground quartz; thus pointing to ·a possible new clue to the cytotoxicity of freshly formed quartz particles and thereby to silica fibrogenicity."

Jan 1, 1988

By R. G. Reddy

Viscosities of alkaline metal oxide-silicate melts were estimated using our previously developed mathematical model. The structural based model considers depolymerization effects and related breakdown of the silicate network structure, on the addition of metal oxides to the melt. The developed expression: n =4.9x10 9 NO 0 T ½ exp(E/RT) poise was used to calculate the viscosities of various binary silicate systems such as, CaO-SiO,, MgO-SiO, and MnO-SiO,, as a function of temperature and composition. Excellent agreement was obtained between the calculated and experimentally determined viscosities.

Jan 1, 1991

By M. Kataoka, Y. Obara

It is known that compressive strength and tensile strength of rocks vary significantly with specimen size. Rocks are composed of crystals and grains in a fabric that includes flaws such as microcracks, grain boundaries and pores. As the likelihood of including severer flaws becomes greater for a larger specimen, the strengths are small. On the other hand, the size effect in the fracture toughness of rocks has not been made clear until now because there are few studies focused on it. In this paper, Semi- Circular Bend (SCB) test was performed using Kimachi sandstone with various specimen sizes. A shape of the specimen is a semi-circular disc with an artificial notch. The specimens were prepared with various thickness t and radius r as the following two groups; t was changed from 10 to 37.5 mm with r = 37.5 mm in the specimen of group (a), and r was changed from 12.5 to 150 mm with t/r = 0.8 in the specimen of group (b). As a result, there was no significant change in the fracture toughness with different t. On the other hand, the fracture toughness increased with increasing r and converged on a certain constant value in a range larger than approximately 70 mm of r. Consequently it was clear that the size effect in the fracture toughness of the sandstone exists.

Jan 1, 2015

By Sharon L. Eyer

"FTIR spectroscopy is employed to define mineable ore deposits based on exploration samples. The RAMBO (Robotic Assessment of Mineable Bauxite Ore) technology is operating successfully at an alumina refinery in K winana, Australia, for assessment of a number of critical ore attributes including available alumina, extractable organic carbon and total iron. Classical methods of analyses for these properties require laboratory-scale digestion of alumina ore (bauxite) or XRF analyses.Multivariate calibration is used in the RAMBO system to generate robust mathematical models that are able to estimate classical data from FTIR spectral data. Furthermore the models can highlight regions of ore that are relatively unusual. Unusual ore may be investigated for potential impacts on refinery processes well in advance of mining.The components of the technology are described and some results for an example application (bauxite) are presented. Challenges and difficulties are discussed. The potential to apply the technique to process control is introduced."

Jan 1, 1999

By Morris M. Fine, Norwood B. Melcher

It is out of the question, at this time, to select any one prereduction process as superior to the others. It is apparent that several share a basic similarity and that within the groups listed in Part 1, the reduction vessel is sometimes the only significant variable. Claims as to the virtues of one machine over another are difficult to substantiate: one may be rapid, another thermally frugal. Based on published data, however, all seem to be performing adequately. It would appear that processes based on carbonized pellets are most applicable to foundry iron at low production rates. Adaptation to large scale manufacture of blast furnace hot metal or to agglomeration of fine concentrates at the mine site is much less likely.

Jan 8, 1966

By Richard A. McIvor

"All mine shaft conveyances in Canada and most of the United States that are supported by a single hoist rope or attachment point and used for transporting persons are required by regulation to be equipped with safety catches and mechanisms. These safety mechanisms, commonly called safety dogs, are designed to stop and hold a free falling conveyance, with a full personnel load, in the event of a hoist rope or attachment component failure. The conveyance’s safety mechanism must be tested under dynamic conditions before it is used to transport personnel. This paper will discuss free-fall testing and it’s results on conveyance free-fall tests performed in the test tower at INCO Limited, Sudbury, Ontario.Topics covered will be free-fall tests on various wood types such as B.C. fir, Karri wood and Trusjoist MacMillan Limited Parallamwood (PSL), comparison of deceleration rates versus free-fall velocity and the influence of safety dog tooth design on deceleration rates."

Jan 1, 1996

By Ernest L. Bradley

A positive pressure ventilation system, augmented by a dewatering well curtain and underground longhole drilling, provides effective ventilation and radon control at EXXON Minerals Company&apos;s Highland Underground Mine in the Southern Powder River Basin of Wyoming. Testing different types of bulkheads, sealants, and bleeder systems has led to improvements in the basic ventilation system. Continued testing of new or different materials and equipment is expected to lead to further improvement in the ventilation program. Effective training of both miners and supervisors is essential to maintaining and improving ventilation techniques. This paper addresses the ongoing ventilation program and experience to date at the Highland Uranium Mine.

Jan 1, 1979