Search Documents

By Stefano Baf

This paper describes the main technical and process solutions applied to the extrathick and wide slab caster built at Yingkou (Liaoning, P.R. of China), as well as all the features required to achieve the surface and internal quality targets.

Aug 16, 2017

By R Nicholson, N D. Cox, N W. A Lambert

"This paper reports on the long-term operation of a particle density meter (PDM) at the Bloomfield coal handling and preparation plant (CHPP). This unit has been operating continuously for over three years, providing real-time data to the operators to allow the monitoring of flotation circuit performance. PDM outputs include slurry density, solids concentration on both mass and volumetric basis, and particle density. Knowing the average particle density of a stream allows for the optimisation of the process in real-time.The calibration of the solids concentration measurement device proved very difficult as the factory calibration techniques and existing laboratory analysis did not give accurate or reliable results. The solids concentration device had to be re-engineered and a new calibration method developed that gave accurate and repeatable results. Independent verification of samples taken from the PDM was undertaken as part of the trial process.The operational reliability of the PDM was a major point of investigation. The initial installation of the unit revealed issues with large, misplaced material of up to 20 mm periodically entering the unit, leading to feed blockages. The presence of these misplaced, oversized particles in the flotation circuit was resolved by installing innovative automatic back flush systems on the PDM.From a plant perspective the PDM has been an invaluable instrument that has enabled irregularities in the flotation circuit performance to be identified, which sampling had not and could not readily identify. This was achieved by close monitoring of real-time tailings composition on a minute by minute basis over short and extended periods. Variations in the tailings stream with respect to particle density and solids concentration were traced back to other issues in the plant. In addition, the PDM has allowed cell optimisation with respect to reagent dose rate to be improved. The PDM with real-time feedback can negate the need for large sampling campaigns and analysis during plant optimisation programs.Citation:Lambert, N, Cox, N and Nicholson, R, 2016. Particle Density Meter, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 245–250 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Greg Yuriy

This paper discusses research carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in the field of discrete-event simulation of mine equipment systems and reliability assessment of these machinery using genetic algorithms. The AutoMod simulation package, from Brooks-PRI Automation Inc., is used in this research. It is a 3-D discrete-event simulation/animation software tool for creating realistic depictions of manufacturing and materials handling systems. Discrete-event simulation involves modeling of real-life systems based on variables and events which occur or change at distinct points in time. In our case, a two level, multi-drift sublevel stoping model was created in AutoMod for the simulation of the equipment fleet employed in the development cycle (drilling, explosives loading, blasting, materials hauling, ground support) of a typical underground mine in the nickel mining region of Sudbury in Ontario, Canada. The equipment primarily considered in the simulation is Load-Haul-Dump (LHD) vehicles (scooptrams), drills, explosives-loaders and roof bolters. The purpose of the simulation study is to assess the impact of equipment failures to mine?s production throughput. In more detail, using Mean Time Between Failures (MTBF) data of scooptrams derived from a reliability assessment model based on genetic algorithms, LHD failures are incorporated into the simulation model. These failures cause production interruptions to the development cycle and consequently loss of hauling capacity. This paper will indicate the significance of equipment failures to a mine?s production and suggest a methodology based on the combination of discrete-event simulation and a predictive reliability assessment model using genetic algorithms for the study and analysis of mine equipment systems.

May 1, 2003

By Paul J. Guay

This report presents the results of evaluating a longwall mining system specifically designed to extract a very deep web (60 inches or deeper) from a longwall panel. The report includes a productivity and cost analysis comparing the new mining sys-tem with a high capacity conventional longwall operation taking a 30-inch wide web. The analysis shows the new system will increase annual production 44 percent and decrease cost per ton off the face 21 percent. The report also includes conceptual drawings and specifications for a high capacity four-drum shearer and a unique shield type of roof support specifically designed for very wide web operation. The advantages and problems associated with wide web mining are discussed in general and as they relate specifically to the equipment selected for the new mining system. The study concludes by recommending that surface coal loading tests be conducted as the follow-on work.

Jan 1, 1978

By J Jardine

An improved ground support method for development intersections, wide spans and stope brows was implemented at Kanmantoo mine. The method uses a jumbo to simultaneously drill and install self-drilling anchors (SDAs) to depths from 4.5 m to 7.0 m. Resin is subsequently pumped into each SDA using a specially designed integrated tool carrier basket, with plating occurring within 10 mins due to rapid resin cure. This methodology means that SDAs can be installed rapidly due to reduced process steps and wait times with reduced hazards to personnel. Cablebolts are used extensively in underground mines to reinforce the ground in wide spans, such as at intersections and stope brows. The flexible cablebolt tendon allows for a long, continuous and high-capacity reinforcing element to be inserted into the rock. A common cablebolt installation practice at Australian underground mines that do not utilise a mechanised cable bolter, is for cablebolt holes to be drilled by a jumbo or longhole rig, hand installation and grouting by a service crew, then plate tensioning following a grout curing wait time of typically 12 to 24 hours. This process involves multiple separate labour-intensive work processes and results in reduced availability of priority headings. This paper discusses the development history of vertical SDA use in wide spans at Kanmantoo mine. The installation process is fully described, including aspects such as reliable in-hole coupling of SDAs, resin selection and pumping aspects. A cost benefit assessment, and a case for ground stability are presented to compare cablebolt use to SDAs in development intersections.

Mar 29, 2023

By W. Abdellah

Underground mine developments, such as haulage drifts and cross cuts, play a vital role in providing access to ore extraction areas for mine production. The stability of mine developments is thus of crucial importance during the life of a mine plan. Many Canadian mines use longhole mining methods or one of its variants. These methods require access to the orebody through mine developments such as haulage drifts and cross cuts on multiple levels. This paper examines the stability of mine development access intersections with respect to the planned mining sequence. A case study, the #1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario, is presented. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) was created for a development intersection situated 1.5 km below ground surface. The stability, or performance of the intersection, is evaluated in terms of the strength-to-stress ratio. The ratio threshold is set at 1.4 for temporary openings. Unsatisfactory performance is defined as a strength-to-stress ratio less than this threshold value. The performance of the intersection stability is evaluated at various modelled mining stages and the probabilistic method of analysis is then invoked to study the probability of unsatisfactory performance of the intersection. The results are presented and categorized with respect to probability, instability, and mining stage.

Aug 1, 2013

By Jonathan Peck, Jim Gray

"While the mine developer looks for bigger and better orebodies in countries offering lower risks to development capital, the opera-tor of existing mines is looking for bigger and better ways to use his existing resources. Mining operations today utilize a variety of stand-alone systems for planning and managing their operations. In both small and large mines, payroll, accounting, inventory, planning, and engineering requirements are met using a combination of manual and computer-based systems.Technical advances and new enabling technologies are changing how mines are doing business. PC-based systems are allowing small operations to join the larger mines in using advanced computer-based systems. Advanced monitors are being used in maintenance to track, predict and correct the health of production equipment. Production monitoring systems are used to measure the performance of operating equipment and personnel in real time. This detailed information on how much, where, when, and by whom is being used for proactive management and planning. Ultimately, this information can be used to optimize and control the machines’ activities, eventually leading to robotic and autonomous operation of mining equipment.As the use of technology increases in mining, specific information objectives are being met but other problems are being created. The life cycle of technology is small, and as current systems are replaced by newer ones, integration problems and additional end-user training are created. In addition, onboard monitoring systems can create large volumes of data, data which are frequently archived without being analyzed. Mine operators are also duplicating efforts applying new technologies in an effort to be more competitive, but in doing so are creating interfaces which are only compatible with their own facilities. As system development moved from the centralized mainframe computer to the PC environment, the fragmentation of these systems became more pronounced.To efficiently continue in adapting and utilizing advancing technology, the mining industry needs to develop a system architecture that readily integrates as many sub-systems as possible. This will provide a framework for existing system integration and design guide-lines for future development. The Total Mining System (TMS) concept will allow a network of stand-alone functional modules to be readily integrated with minimal effort. This paper will discuss some of the current technologies cur-rently in use in some surface mine operations.In addition, a description of the information system and communications requirements that will be needed to integrate these components in the future, will be discussed."

Jan 1, 1996

By E. Gaucher, D. C. Gagnon

"The paper refers to methods and concepts used in the computer treatment of banks of geophysical, geochemical and geological data, relating to the exploration of massive sulphides. In particular, a data bank of 400 drill holes on independent conductors can be used to calculate probability levels of intersecting a certain quantity of sulphides according to the characteristics of the conductor. Inversely one can, using the data bank and some cost assumptions, simulate and optimize the cost of intersecting a certain quantity of sulphides by selecting drill targets among conductors according to conductivity, magnetism or gravity. Problems of noise, inherent in any simulation, are illustrated in this paper by the results of a study of the nomenclature of volcanic rocks of 27 drill holes by forty geologists. Compilations of data banks are long and timeconsuming, and it would help to standardize to allow exchange of data. We believe that such efforts may result in the discovery of more mineral deposits and at a lower cost. The present study is supported jointly by SOQUEM The New Jersey Zinc Co. and Cominco Ltd."

Jan 1, 1973

By C. Matthews, A. Vo

Australia is one of the world’s leading exporters of bulk commodities and the extensive use of sampling equipment is key to the successful management of each mining operation. At the process plant, without a full understanding of the feed, product and tails, it is impossible to fully optimise the performance of the plant, such that the metallurgical balance is often open to error. At the port, a statistically correct, bias free and compliant sampling system is crucial to ensuring exported minerals are reflective of their true value and to avoid penalties. Over the last decade, as a result of the iron ore boom, there has been high demand for reliable, representative and standard compliant solids sample systems in Australia. This paper reviews several solids sampling applications at Australian mine sites, the challenges and experience gained and how the implementation of reliable representative sampling systems has provided better understanding of plant process performance, improved plant control and overall benefits to the operations. INTRODUCTION Mining is the primary contributor to the Australian economy with Australia ranking in the top 4 in economic resources for 21 primary industrial minerals in 2016 (Britt, et al., 2017). Australia is one of the world leaders in the export of the majority of its commodities including gold, copper and iron ore (Britt, et al., 2017). Therefore, a suitable and standard compliant sampling system is essential for evaluating plant performance and content verification. At the mine and at the port, the larger iron ore miners in Australia have developed stockpile models to predict the grade of their ore down to individual blocks of the stockpile. This allows the miner to create the right blend of material for sale to their customers and ensures they are not underselling their product or at risk of penalties for impurities or low grade. As an example, the average difference between the benchmark 62% Fe and low grade 58% Fe fines at the time of this report averaged US $20/tonne according to the Metal Bulletin Iron Ore Index (Fastmarkets MB, 2019). At a shipload of 180kt this would be a variation of US $3.6M. Whilst this is an extreme example, it highlights the economic importance of producing the correct grade product and a recognised representative sample of said product.

Jan 1, 2019

By E. G. King

In continuation of the study of thermodynamic properties of the common interoxidic compounds of ferroalloy elements, this report gives the results of low-termperature heat-capacity measurements and entropy evaluations of the monotungstates of sodium, magnesium, and calcium. Previous reports4 5/ of this laboratory dealt with low-temperature heat capacities, entropies, and heats of formation of the sodium vanadates. Heat-capacity measurements of the monotungstates of sodium, magnesium, and calcium (Na2W04, MgW04, and CaW04) were conducted throughout the temperature range 51° to 298° K. The entropies at 298° K. were evaluated and then combined with entropy data for the elements and oxides to obtain entropies of formation. This information is an essential part of the data needed for thermodynamic appraisals of chemical reactions of these substances. No similar data for any tungstate are to be found in the literature.

Jan 1, 1961

By Franziska Günther, Helmut Mischo

The calculation of costs for an underground mine, as well as the planning of the equipment and materials to be used, is a complex and time-consuming process. The estimation depends on a multitude of parameters, and all mining processes are interconnected. A novel tool has been developed that enables automated calculation of underground mines and allows for the comparison of the effects of changing individual parameters. Previously, changing individual planning parameters often necessitated a complete recalculation of the mine. The newly developed calculation tool provides an innovative planning aid that allows for more efficient and accurate mine planning and cost estimation. The tool enables the user to implement continuously up-to-data costs and prices. This allows for more accurate planning data and results. The underlying concept of the calculation tool, its implementation at a planned quartz porphyry mine in Germany, and the verification of the tool at an existing underground mine will be presented.

Feb 1, 2025

By Louis A. Panek, John A. Stock

A flat slot is created in rock to cause stress relief effects in a pair of hydraulic borehole pressure cells (previously installed in drill holes above and below the slot ) , which act as sensing devices . This relief is annulled by repressuring the slot by means of a flat hydraulic cell . The slot pressure at annulment is taken to be the existing ground stress at right angles to the plane of the slot . A number of trial installations in the rib of a mine drift showed that for a valid determination of ground stress the sensing devices that respond to relief and repressuring must be within a specified zone close to the pressure transmitter ; otherwise the indicated ground stress may be excessive . By using an additional pair of borehole pressure cells , installed a few feet away , the existing rock stress can be redetermined at intervals , irrespective of a change of stress intensity subsequent to the initial installation . Based on these findings , equipment and procedures have been developed that make possible the installation and operation of a permanent rock stress monitoring station for observing mining - induced stress changes . The station consists of a 12 - in - wide hydraulic pressure cell cemented in a flat slot and four 2- by 8 - in flat hydraulic pressure cells in nearby drill holes . All drilling for the installation can be done with an air leg drill and conventional bits . Once the installation is completed , all required information is obtained by Bourdon pressure gage readings . The apparatus is simple , relatively inexpensive , and reliable under operating conditions in a wet mine . Unlike most methods of rock stress determination , this scheme permits periodic remeasurement of absolute rock pressure over several years , without additional drilling or instrumentation . Similar to other flat slot procedures , stress measurements are obtained without making auxiliary tests to determine elastic

Jan 1, 1964

By W. McCombe, G. Remple, L. Zunti, M. Bernardin, L. Nightingale-Mercer

"The McClean Lake Mill is located approximately 700 kilometres north of Saskatoon, Saskatchewan, Canada and is operated by AREVA Resources Canada Inc. (AREVA). The mill was designed to process high grade uranium ores, and has been undergoing a multiyear expansion to increase its production capacity to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to processing high grade ores from the Cigar Lake Mine. During the metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit have a propensity to generate hydrogen gas during acid leaching. Hydrogen is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit. Uranium processing is further complicated by the fact that an oxidant in the form of oxygen gas or hydrogen peroxide is required to regenerate iron in the leach, which further increases the risk from hydrogen gas. During 2013 Hatch and AREVA designed and engineered a number of novel upgrades for the leaching circuit to mitigate the risk of hydrogen gas evolution in the process. Best in class technology was utilized in addition to control and operating strategy changes to ensure the leaching circuit can be safely operated with ores that can evolve hydrogen gas. This paper reviews the design concepts and modifications implemented on this unique and challenging project.INTRODUCTION The McClean Lake mill was originally designed to process high grade uranium ores, however until 2014 the average ore grade processed was 1%. The facility has been undergoing a multiyear upgrade and expansion to increase its production capacity from 12 to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to new high grade ores, averaging 18% U, from the Cigar Lake Mine. During the last round of metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit had a higher propensity to generate hydrogen gas during acid leaching than previous test work had indicated. Hydrogen gas is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit."

Jan 1, 2017

By B. Csoke

The Bond and the Hardgrove methods are widely used for the determination of the material?s grindability. Generally, the determination of the Bond work index of inhomogeneous materials can be carried out with high deviation using the conventional apparatuses and methods, because of the highly different grindability of components. This is more significant when the composite cement?s grindability is measured, which highly affects the design and operation of cement grinding mills. A possible solution can be the combined application of the Bond-method with the determination of the component?s weight ratio in the product and perform the Bond measurement until the steady state conditions of grindability coefficient (G) and chemical composition of the components are reached. To prove the applicability of the above mentioned idea systematic Bond and Hardgrove grindability tests were carried out of two phase composite materials. The experimental results showed that the application of the combined procedure is proven in order to have a more accurate and reliable calculation of the Bond work index of composite materials, especially when the components have significant difference in the grindability and concentration. The measurements also showed the possibilities and limits of the grindability test methods.

Sep 1, 2012

By Y Gu, R Fandrich

Traditionally, characterisation of the mineralogy and textures of ore and rock samples were based on observations of hand specimens and thin sections using an optical microscope. The extent of the data collection was limited by the available tools and thus variations in mineralogy and texture were generally not described by quantitative data. These qualitative to semi-quantitative approaches, even though well established over the years, resulted in variable observations and data sets. The data were unlikely to be representative of a sample and limited statistical validity meant the results could not be reliably used in modern digital mining design and planning. With recently developed SEM based quantitative mineralogy tools and the corresponding methodologies, ore textures can be quantified and compared numerically. The numerical data can not only enhance the understanding of an orebody in geological terms, but can also be used in the creation of metallurgical models for mine and mineral processing design and simulation. These capabilities provide valuable inputs to risk assessment studies and the evaluation of mineral projects.

Jan 1, 2007

By Casandra Gamez Gonzales, Angelina Anani

Copper, the newest addition to the critical mineral list, is an essential metal whose electrical and heat conductive properties label it as a vital mineral for the creation of renewable energy sources and the reduction of Greenhouse Gases (GHGs). However, despite copper’s leading role in the transition to sustainable energy and mining practices, the mining industry has faced various battles in the extraction of this valuable material. These challenges are based on mining’s negative reputation and extensive impact on the environment, nearby communities, and human rights. To ensure the survival of mining in the future and achieve mineral demands, an emerging topic that has initiated the revolution of the traditional sector into a more environment- friendly and transparent industry, is Environmental, Social, and corporate Governance (ESG). ESG has motivated companies to seek growth opportunities and standardize risk accountability and transparency based on its collective framework that creates, modifies, and implements local, national, and international standards. These standards focus on improving environmental, social, and governance issues faced by companies and their projects. ESG has served as a guideline that investors utilize to assess companies and promote sustainability, responsibility, and disclosure to create positive and balanced relationships with stakeholders and the environment. Nonetheless, concerns have been rising which state that ESG is negatively impacting the mining industry by targeting what fuels the industry and world: ore deposits and their resources. Therefore, this research focused on answering the following research questions: what are the impacts of ESG on the copper supply chain and how will stricter ESG standards affect future copper production?

Feb 1, 2024

By R. Nilsson

In the present work, an assessment of the sulphide capacities of a number of binary and ternary slag systems have been carried out in the light of a sulphide capacity model. The model is based on the expression: {CS- exp (-A G °/R T) ? ao2 / fs2-} where AGO is the standard Gibbs energy change for the above reaction, ao2 is the activity of oxygen ions and f, is the activity coefficient of the sulphide ion in the slag. In the present model, the ratio (ao2/fs2) is optimized for the experimental data available in literature. The systems assessed are the binaries MnO-SiO2, CaO-SiO2, Al2O3-CaO, as well as the ternaries CaO-Al2O3-SiO2 and CaO-MnO-SiO2. In the case of all these systems, the experimental data available in literature were complemented by measurements carried out at the Division of Theoretical Metallurgy. The sulphide capacities of some FeO- containing binary, ternary and quaternary slags are also examined. The potentiality of the model to estimate the sulphide capacities of complex slag systems from binary and ternary data is demonstrated.

Jan 1, 1996

By G. R. Waters

NMR360 is developing a suite of chloride-based metals extraction processes, with the first commercial operation scheduled for commissioning late in 2018. It is critical, therefore, that with the introduction of any new technology, that the circuits do not suffer from mechanical failures which will compromise the operation. Although chloride leaching is at atmospheric pressure and relatively low temperature, the main challenge is preventing corrosion, since the high proton activity makes even a small amount of acid behaves as though it were concentrated. An additional challenge in concentrated chloride circuits is the potential for solids precipitation. In this context, therefore, correct valve selection is crucial, and NMR360 has partnered with CGIS to ensure that the Severe Service Valves (SSVs) needed will perform over and above the definitions of the Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry. This paper outlines what the minimum requirements are for SSVs in chloride leaching applications, drawing on five decades of industry experience from one of Canada’s leading valve experts.

By Cesar O. Gomez

A procedure has been developed for mounting at random particles of mineral samples to be characterized using image analysis. The procedure is based on the generation of a random distribution of sample particles in particles of a diluent material. and the embedding of this particle mixture in an epoxy resin without disturbing the initial distribution. Two materials with atomic number similar to that of the epoxy resin were successfully used as diluents: activated charcoal and graphite. The proportion of diluent material to be mixed with the sample to have a large number of mineral particles in the field of view while keeping the occurrence of touching particles at an acceptable level was determined empirically. The randomization achieved with the procedure developed in this work was tested using as samples known mixtures of silica and pyrite particles of the same sieve class. The agreement obtained between the mass ratio of minerals used in the preparation of a particular specimen and that resulting from image analysis demonstrates that the procedure developed is successful in producing a specimen where the embedded particles are randomly distributed.

Jan 1, 1988

By Z. Ruetz

Portable X-ray fluorescence (pXRF) analysis has been widely adopted in the geochemical and environmental field as a cost-saving alternative to standard analyses. This paper outlines the efficacy of a method for indirectly quantifying organic copper content in solvent extraction circuits via stripping of the chelated metal with concentrated sulfuric acid in a single contact and subsequent pXRF aqueous analysis. pXRF analysis is common within the mining industry but presents unique challenges with liquid analysis, the most prevalent of which are briefly discussed. This method was developed specifically for mining operations with regional constraints and limited resources. Providing an in-field alternative to flame atomic absorption spectrophotometry and inductively coupled plasma optical emission spectroscopy, this entirely mobile XRF analysis method produces consistent and accurate results within minutes and at a fraction of the cost.

Jan 1, 2023