Search Documents

By B. Samanta, S. Bandopadhyay

Ore grade modeling of a placer gold deposit is considered a challenging problem even today. Typically, gold-bearing deposits show extremely erratic and unpredictable grade variation. This is principally because of isolated occurrences of gold metal within a few high-grade pockets. Because of sporadic fluctuation of high-gold-grade distribution, the overall spatial continuity of the deposit becomes poor. This type of variation is often described by a lognormal or highly skewed frequency distribution, and the spatial continuity of the deposit is characteristically represented by a variogram model that exhibits a high nugget component. Further complicating the matter is the sparse availability of drillholes to capture such erratic variation. Due to the prohibitive cost of drilling, gold grade and reserve estimations are typically carried out using insufficient exploratory data. Use of a traditional estimation technique on limited data often produces an unreliable ore grade model. Kriging and its nonlinear variation, lognormal kriging, are frequently used in gold deposit modeling (Rendu, 1979; Journel, 1980); however, kriging is flawed by the smoothing effect. Moreover, though kriging is known to be globally unbiased, it is not free from conditional bias. As a result, if a deposit is modeled using the traditional kriging technique, a high-grade zone can be predicted to be a low-grade zone and vice versa. Predicting high grade as low grade results in a missed opportunity to exploit profitable ore. On the other hand, prediction of low-grade ore as high-grade ore might result in financial loss for a mining operation. Thus, the use of kriging for ore grade mapping of a gold deposit may not be recommended. Estimation techniques (including kriging) can produce an estimate with minimum error in a minimum-error variance sense. However, no matter which estimation technique is used for grade modeling of a highly erratic deposit like gold, the error margin is bound to be high. Therefore, any grade prediction made for an unknown location is associated with high uncertainty. Since various mine-planning operations, including derivation of grade tonnage curve, pit design and economic analysis of the deposit, are based on estimated grade rather than true grade, a mining project evaluation that depends upon estimation will be subject to considerable risk. Thus, the successful design of a mining project not only depends upon accurate grade estimates, but also upon accurate assessment of uncertainty, for predictive grade is equally important. Although the kriging standard deviation is used as an indicator of uncertainty for prediction, it is flawed by characteristics related to a data-independence property. This study, therefore, investigates the stochastic simulation technique of conditional simulation for ore grade modeling of a placer gold deposit at Nome, Alaska. It is expected that the research will provide a better solution to ore-grade deposit modeling than the kriging technique because (1) conditional simulation preserves spatial continuity as well as reproduces the data histogram, thus avoiding the smoothing problem; and (2) generation of multiple realizations helps to accurately quantify the uncertainty about grade values in the deposit.

Jan 1, 2009

By S-E. Vandat

The goal of this work was to select an appropriate electrode for dummy load of diesel engine in fully salt-water in the DESA factory. The electrochemical corrosion rate of general structural steel, commercial pure aluminum and cathode copper calculated as weighting, volumetric and commercial in fully salt-water by city power. After several tests and then applying the fuzzy logic method, it was determined that general structural steel is the best selection for this purpose.

Jan 1, 2005

By A. G. Jackson, Mark D. Benedict, Steven R. LeClair, Yang Cao, David M. Conrad

"Electronic Prototyping (EP) represents a new and powerful medium that many in science and technology view as the research paradigm of the future. Actually, EP has many handles, sometimes referred to as simulation-based design involving more long term objectives such as virtual reality, but regardless of the 'spin', the direction of EP is an enhanced visual paradigm to enable a new set of tools for engineers and scientists alike. Tools to not only automate, visualize and compute otherwise intractable problems but to enable augmentations of our ability to perceive that which is interesting and new -""a virtual version of a process"" [1] prodding us on the pathways of materials and process discovery.IntroductionActually there are many reasons to apply sensors to materials, such as smart or adaptive materials/structures, and new materials synthesis/processing [1], only some of which are motivated by improved product quality and/or productivity. Although U.S. Air Force applications of sensors to materials processing represent but one of many perspectives, hopefully it is a perspective which will engender new ideas and insights in addressing future challenges in materials research. To provide context and establish need for future sensor applications in materials processing, we will utilize on one of several Air Force vistas or '21st-Century' objectives."

Jan 1, 1997

By K. Boakye, T. Newman, P. Bláha, M. B. Toelle

"This paper presents a quarry optimization plan using a block model and an in-house development quarry scheduling and optimization software (QSO Expert) to help improve quarry operations at Crystal River. The Crystal River Quarry is an underwater quarrying operation that barges limestone via the Gulf of Mexico, as the main source of raw material to a cement plant in Theodore, Alabama. To improve the quarry operation, an evaluation was completed to optimize the quarry planning and extraction procedures of the quarry. In order to achieve this, additional exploration drilling campaign was implemented, a new block model was re-calculated and the latest version of QSO Expert software was used. The primary economic impact is a higher recovery of limestone reserves; sustainability of resources, corresponding longer quarry life. Secondarily as the limestone is mined underwater and stockpiled above water, drainage reduces moisture content achieving direct cost reduction on limestone shipping. In addition, a considerable reduction in operational cost was achieved due to a significant decrease in consumption of electrical energy, reduced dragline maintenance costs and reduced dragline movements within the operation. INTRODUCTION Holcim is a Swiss-based global building materials and aggregates company. Founded in 1912, the company expanded into France and then throughout Europe and Middle East during the 1920s. In 1922, Holderbank, as the company was then known, expanded beyond the Swiss borders into France. By the end of the decade Holderbank held stakes in Belgium, Germany, the Netherlands, and Egypt (Holcim History 1912-2012) Positions in Lebanon and South Africa soon followed.. Holder bank later expanded in North America in the 1950’s. In the late 1970s and early 1980s, Holderbank continued its expansion in Latin America, Asia and Spain for the first time. The company expanded into Eastern Europe and experienced a boom in Spanish construction preceding the 1992 Summer Olympics. By 1986, Holderbank was the world's largest cement manufacturer. In the 1990s, the company consolidated its European holdings as the American market drove growth. Expansion into Eastern Europe and Russia continued (Holcim History 1912-2012). In 2001, the company changed its name from ""Holderbank Financière Glaris"" to Holcim (short for Holderbank ciment) (Holcim History 1912-2012). Holcim expanded by purchasing Aggregate Industries entering into the United Kingdom for the first time. That year, the company also expanded into India by acquiring a stakes in The Associated Cement Companies (ACC) and Ambuja Cement Eastern. In 2008, Holcim became the largest shareholder of China's Huaxin Cement with a 40% stake. In 2009, they acquired Cemex Australia. In 2014, Holcim and Lafarge announced they had agreed to terms on a ""merger of equals"" valued at nearly $50 billion in 2015. The new company LafargeHolcim based in Switzerland has a manufacturing capacity of 427 metric million tons a year."

Jan 1, 2017

By Isabela Costa Mendes Peres

As soldas dissimilares de liga de níquel 182 são utilizadas em usinas nucleares para conectar tubulações de aço inoxidável com componentes fabricados em aço de baixa liga. O procedimento envolvido na soldagem dissimilar pode modificar as propriedades do material, o que afeta diretamente a junta soldada no sentido de aumento da probabilidade de incidência do processo de corrosão. Neste trabalho foi realizado a soldagem dissimilar de corpos de prova dos aços de baixa liga e aço inoxidável austenítico AISI 316L com as ligas de níquel 82 e 182. Estudou-se o comportamento frente à corrosão da junta de solda de liga 182 em ambientes ácidos contendo NaCl e Na2S2O3 empregando-se técnicas eletroquímicas. Ensaios de polarização anódica potenciodinâmica foram utilizados para caracterizar o comportamento de corrosão localizada do material. Os resultados mostraram que o comportamento eletroquímico da junta de solda está relacionado com o aporte térmico e a presença ou não de oxigênio no meio.

Aug 8, 2018

By Anja Pfennig, Thomas Böllinghaus, Marcus Wolf

During CCS components are exposed to a corrosive environment and mechanical stress which results in corrosion fatigue and is inevitably followed by the lifetime reduction of these components. The lifetime reduction of the cyclically loaded high alloyed stainless injectionpipe steel AISI 420C (X46Cr13, 1.4034) constantly exposed to highly corrosive CO2- saturated hot thermal water is demonstrated in in-situ-laboratory experiments (T = 60 °C, brine: Stuttgart Aquifer, flow rate: 30 l/h, CO2) in an environment similar to the on-shore CCS-site in the Northern German Bassin. In-situ tension-compression experiments were established simultaneously along with electrochemical measurements using a newly designed corrosion chamber in a resonant testing machine at a frequency as low as 30 – 40 Hz. In addition technical CO2 was introduced into the closed system at a rate close to 9 L/h. S-N plots, micrographic analysis and surface analysis of the fracture surface are demonstrated. X46Cr13 (surface roughness Rz = 4) reached the maximum number of cycles (12.5 x 106) at stress amplitude of 173 MPa producing a low scatter range of 1:3.5. Hydroxide and siderite layers were found on pits and crack surfaces. No typical fatigue limit exists. Pit corrosion prior to crack initiation may be identified as failure cause.

Jan 1, 2016

By Thomas Niehoff

"Oxyfuel combustion systems are state of the art for many melting operations. Airfuel systems have been stepwise modified to oxygen enrichment, oxygen lancing and oxyfuel. Every change of the melting process will have consequences with regards to emissions and energy usage. The uniqueness of many operations requires unique skills to resolve potential issues. This paper will give some examples of how airfuel systems can successfully be converted to oxyfuel.IntroductionOxyfuel technology – meaning the combustion of fossil fuels such as natural gas, oil or coal with technical oxygen instead of air for industrial melting or heating processes is widely used in many industries these days. Even though oxygen production, storage and handling has been state of the art for decades other opinions exist. Often oxyfuel is regarded with fear and potential hazards like: “Oxygen makes the process too hot.”, “Oxygen will melt away the refractory.”, Liquid oxygen is dangerous.”, “Oxygen will cause explosions.”, ……etc.Typically a more detailed discussion about a specific industrial process and how oxygen can be applied in a safe and economic way the seeming issues go away."

Jan 1, 2010

By Roger Francis

There is increasing use of acid leach extraction methods at elevated temperatures and pressures by the mining industry. In many locations there are limited supplies of fresh water, and waters with higher chloride contents must be used, making conditions more corrosive. The fluids downstream of the main autoclave are hot, acidic, oxidizing and contain chlorides and present a challenge to the mining community to ensure reliable operation. Zeron 100 is a high strength superduplex stainless stee, that offers high corrosion resistance at a cost effective price. The paper presents a combination of laboratory data and service experience, particularly in the aggressive fluids found in downstream processing.

Jan 1, 2010

By Xuewei Lv, Yuelin Qin, Guibao Qiu, Chenguang Bai

"Blast furnace slag (BF slag), is the main by-product in the ironmaking process, which contains large amounts of sensible heat. To recover the sensible heat, this paper described the hot experiments which were carried out in a rotary multi-nozzles cup atomizer, where the molten BFS was transformed into granules without water impingement; subsequently, a new method-pyrolysis the printed circuited board (PCB) with the hot BFS particle, was proposed for recovering the sensible heat in this study. The gaseous products were analyzed by gas analyzer. The residual of the PCB was analyzed by FT-IR and XRD respectively, and the obtained slag particles were analyzed by XRD.The results showed that it is a feasible process of pyrolyzing PCB powder with the hot BFS particle. The sensible heat of hot BF slag could be converted to chemical heat and a large amount of combustible gas could also be generated during the process.IntroductionDue to the rising of the product cost of blast furnace iron (BFI) and the increasing public awareness of environmental problems, the steel industries have to focus on the energy saving and emission reduction. Blast furnace slag (BF slag) is a byproduct from blast furnace exhaust temperature of 1450°C or so, is a high-quality waste heat resources. In China, the steel industry produces approximately 220Mt ofBFS per year, and the enthalpy of those slags is approximately equivalent to 13.3% of the whole energy consumption in the ironmaking process[!]. It can be seen, recycling waste heat is an important way of energy saving for iron and steel enterprises. The molten slag was treated by conventional water quenching method without any recovery of heat in spite of its huge potential. Also, the water quenching process consumes a plenty of water, pollutes the air and water[2]. Additionally, the extra energy is necessary for the drying process of slag to produce cement. As a kind of secondhand resource which can be reused, the BF slag contains a large amount of sensible heat. To recover the sensible heat of BF slag, three key problems should be considered, which refer to ( 1) the dry granulation of BFS without consuming water, (2) how to recover the heat of slag particles efficiently, (3) how to use the slag particles after heat recovery."

Jan 1, 2012

By M Yahyaei, P Knights, M S. Kizil, J Qu

Digital Twins (DTs) are transforming business operations across many industries through their accurate representations of physical entities enabled by IoT technologies.

Sep 1, 2024

By M. M. Tilman

The Bureau of Mines conducted research to determine the feasibility of strengthening experimental magnesium-base sheet alloys by strain softening induced by controlled cold rolling followed by selective heat treatment. Relatively small alloying additions having potential for producing strain softening were selected from metals that are readily avail-able. Tensile properties comparable to minimum properties of the most commonly used magnesium-base sheet alloy AZ31B, in the H24 condition (strain-hardened and partially annealed), were obtained in an Mg-IMM (mischmetal)-O.5Mn alloy after strain-softening rolling followed by heat treatment. Tensile properties of the experimental alloys in certain conditions are also compared with minimum tensile properties of other standard magnesium sheet alloys. Incidental to the principal objectives, apparent superplastic behavior was observed in three experimental magnesium-base alloys containing MM, MM plus manganese, and MM plus zirconium.

Jan 1, 1985

By Nikhil Dhawan, Shrey Agrawal, SHAILA MIR

The current study investigates the effect of microwave processing on low-grade banded iron ore using charcoal, coking coal, and non-coking coal. Charcoal showed better microwave heating response at low temperatures, and the coals exhibit better heating response at higher temperatures. Low carbon dosage ~ 12% is sufficient to generate concentrate with 61.8% iron grade and ~6% for 94.8% iron recovery comprising of magnetite phase suitable for iron-making applications. The process separation efficiency of ~ 95% is achieved at 6% carbon dosage and decreases with an increase in carbon due to formation of the fayalite phase. The metallization degree showed a strong dependency on reductant dosage and achieved amaximumvalue of 22.7%at 18%charcoal. The comparison of ore with pure iron oxide and the synthetic mixture of iron oxide indicated that the underlying bonding due to banded structure enhances the Joule heating during microwave irradiation and thereby aids in attaining higher temperature and better separation.

Sep 21, 2020

Discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.61-71, consisted of a written comment by Wood P.L. that a larger battery would be the only way to secure reliability

Dec 1, 1916

By A R. Bye

The mining industry is facing some key challenges that provide a compelling case for geometallurgy initiatives. Over the last 30 years, the average grade of Australian orebodies being mined has halved while the waste removed to access the minerals has more than doubled. In the last eight years, the industry’s energy consumption has increased 70 per cent while multi-factored productivity has fallen 24 per cent. The paper documents a broad range of industry case studies which demonstrate strategies for gaining value from geometallurgy.The mining industry constantly faces the key questions of how significant ore variability is on mine valuation and how would knowledge of the variability change the mining schedule, mine to mill design and operation. Using case studies the paper describes the methods used for incorporating mineral extraction attributes into orebody models and their technical integration into daily operation as well as mine planning optimisation. While pit optimisation from a fully attributed geometallurgical model highlights areas of opportunity and risk it is shown that during the scheduling phase of mine planning that significant value can be added. The benefits from these projects included reducing geotechnical and environmental risk, improving mine to mill performance, option analysis and quantified cash flow risk. There is growing acceptance within the minerals industry that ‘realistically assumed modifying factors’ defined by a competent person/s are not sufficient to mitigate the risk of funding mining ventures. Geometallurgy is moving away from factored ore reserves to data-rich block models providing reliable information for mining, metallurgical and environmental considerations.

Sep 5, 2011

By R. C. Miranda

The purpose of this work is to present ?state of the art? mass balances closing strategies in ore treatment plants. It presents a brief history of difficulties and challenges ahead. The current methodology is based on usage of an expert system, which seizes and filters the plant data, analyzes situations of equipment stops and mostly instruments failures. It is still possible to internally create a strategy to check the data of an instrument failure. The system is coupled to software with a Lagrangian model of mass balance closure that receives the pre-treated data. Thus, the data goes through filtering and reconciling processes to generate a reliable mass balance of the ore treatment plant. This made possible to obtain a system that is able to tell the real productivity of a ore plant through reliable mass balances. Residence times on equipments are critical to the balance, thus, they require good logic to eliminate errors due to the characteristics of non-steady state. Among the next challenges is the inclusion of a ?soft sensor? as a replacement of an instrument required for mass balance closure.

Sep 1, 2012

This report, authorized by a subcontract with the Crouse-Hinds Company per Section 1.1.3b of Contract Number H0220065 Amendment Number Six, and the consent of the Contracting Officer, documents the results of an investigation to develop solid state ballasts for Lucalox high pressure sodium lamps. The ballasts were to be used in the modified and new portable and machine-mounted lighting systems designed by the Crouse-Hinds Company, per Tasks I through IV of Contract No. H0220065.

Jan 1, 1976

By William C. Cooley

[ ]

Jan 1, 1975

By J J. L du Plessis, S Viviers, G Ratner

Escalating electricity costs are one of the biggest operational cost drivers in mining. The trend to use high-powered auxiliary fans delivering increased airflow to meet the dilution requirements of diesel equipment, together with the reliance on ducted systems rather than traditional flow-through systems to ventilate areas, increases the overall energy requirements of ventilation systems. To manage and reduce electricity costs energy management systems can be implemented, inefficient operating units can be replaced and the operation of energy-consuming components of ventilation systems can be optimised.This paper describes the process followed to design and develop an energy-efficient axial flow auxiliary fan. The fan-targeted design was based on static pressure and volume flow rate requirements incorporating higher overall fan efficiencies. A brief overview of the results is given, including the aerodynamic design procedure using computational fluid dynamic (CFD) analysis. The mechanical design criteria used, including stress analysis on the rotor and designs to improve the vibration levels of the fan, are also presented. Through this study it was demonstrated that the aerodynamically designed rotors using profiled and twisted blades improve the total fan efficiency considerably when compared with some of the older-generation fans using cambered plates. The latter were typical in the mining sector in South Africa at the time of the study where average overall fan efficiencies of standard cambered fans less than 63 per cent and some of the older-generation cast aluminium blades have peak overall fan efficiencies of about 65 per cent. Peak overall fan efficiency of more than 80 per cent was achieved by using the described design and development process. Additional benefits are that the fans are quieter due to the better aerodynamic design and have a longer operating life due to reduced vibration levels.In conclusion, the use of CFD to develop fans to deliver the required volume flow at the required pressure allows quicker design turnaround time. It furthermore allows the ventilation engineer the option to specify a specific fan and is not limited to an off-the-shelf catalogue fan. It thus allows engineers to purchase a fit-for-purpose energy-efficient fan. The introduction of reliable fan control systems may, however, still result in the biggest cost benefit for underground mines.CITATION:du Plessis, J J L, Ratner, G and Viviers, S, 2015. Design and development of energy-efficient secondary axial flow fans, in Proceedings The Australian Mine Ventilation Conference, pp 337–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By B. Arvidson

Computer-controlled machine sorting may, if properly applied, have a dramatic effect on overall economics of a mine operation. Radiometric and photometric sorters have been used for many years and new developments will be reported, such as a sorter for fine particles and a conductivity/magnetic sorter. Application examples with emphasis on precious metals will be given. Economics for some of the projects will be reviewed and discussed. Sorting underground is shown to be particularly attractive, but machine sorting would be profitable in most cases based on savings in transportation and milling/beneficiation costs only.

Jan 1, 1987

By Luther W. Bahney

(San Francisco Meeting, October, 1911.) LIME is the alkali that is almost universally added to the solutions in the cyanide process of gold- and silver-extraction for maintaining the so-called, protective" alkalinity. It is produced by the burning of limestone. The value of lime for this purpose depends upon the percentage of calcium oxide contained, which is determined by three factors : 1, purity of the limestone used; 2, degree of the burning-temperature and the period of burning; and 3, length of time of storage of burned material and the condition stored, and whether it has been damp or wet during the storage. These three factors render uncertain the quality of lime bought in the open market. In the United States, lime bought from reliable manufacturers, who thoroughly burn a pure limestone and deliver at once to the consumer from the kilns, may be of a fairly-high and uniform composition ; but in Mexico and Central America, where it is purchased from many small producers, who often start with a poor grade of limestone and burn it in small crude kilns with as little fuel as possible, the quality of the product is quite variable. In consideration of the foregoing, it is apparent at once that there is a great need for a rapid technical method for the valuation of the lime to be used in a cyanide-plant. The determination of calcium by the gravimetric method, with the necessity of determining also the proportion of carbon dioxide, silica, and iron, requires too much time, and is usually out of the question for an isolated plant unequipped with a skilled chemist and, the necessary apparatus. The calculating of all the calcium so found to calcium oxide, although sometimes done, is manifestly very inaccurate.

Nov 1, 1911