Search Documents

By G. A. Reinhardt, H. J. Cutler

ThE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4-in. (14.5 cm.) square bloom to a 3/4-in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900" to 950' C. and cooling slowly in mica. The test bars were tempered by heating to 825' to 875" C., quenching in water, and drawing to 515" to 535" C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. UlTimate Strength.. Elongation, Lb. pER Sq. In. PEE Cent.. in 4 In. Not LeEs Than Annealed specimens.............. 78,230 to 92,450. 18 Tempered...................... 120,000 to 149,350 9 After experience on this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850" to 900" C. and cooling in still air; the annealing, in heating to 850" to 900" C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were: yield point, pounds per square inch minimum, 44,800; ultimate strength, pounds per square inch, 89,600 to 112,000; elongation, per cent. in 2 in. not less than 17. Difficulty was encountered as soon as work on this material was started. Many precautions and refinements were instituted but it was found very difficult to secure the required elongation.

Jan 1, 1920

By W. H. Forbes

The prevention of accidents from falls of roof and coal requires a considerable amount of personal judgment , for conditions are different even in adjoining working places in the same mine , and conditions may change from hour to hour even in the same working place as the coal is shot down and loaded . Experience has shown that many men can not or do not exercise enough care to protect themselves from injuries ; moreover , where the foremen have been made directly responsible for the safety of the men under them , accidents from falls of roof and coal have , in many instances , been reduced as much as 50 per cent . There is now no question that careful , constant , and intensive supervision is essential in preventing acci- { dents and more especially accidents of this class . Falls of roof and of coal account for approximately 50 per cent of all coal mine accidents and annually result in the death of approximately 1,000 men and cause lost - time injury to approximately 50,000 men . These and other accidents are recurring with little or no diminution , usually not because of the lack of knowledge of safe and dangerous practices , or of the technique of safety , but largely because of the lukewarm interest of major executives in safety or the failure of mine officials to formulate and to enforce common - sense rules and regulations . When failure is the outcome of a sincere attempt of the managing officials to teach safety to the miner , the fault may usually be attributed to misguided effort . Various solutions for the problem of eliminating accidents from falls of roof or coal have been suggested , some of which are : Standard system of timbering for the specified mining districts ; departure from the room-and - pillar system to a more concentrated system of mining ; more intensive supervision - that is , 1 section foreman for every 25 loaders instead of 1 section foreman for 75 , 80 , or even more loaders the practice in most mining districts . - However , investigations conducted by the writer at numerous mines operated by a number of mining companies in several districts show that employees and officials alike are inclined to work under loose and unsupported roof , relying solely on the " drummy " sound and on their judgment and experience as to whether the roof will stay in place for one hour or for several hours . With but few exceptions , men who had been injured by falls of roof or ccal or were found working under loose and unsupported roof , admitted that they knew of the possibly unsafe condition , but it was their opinion that the roof or coal was not loose enough to fall for some time .

May 1, 1931

By Robert F. Shurtz

This paper discusses and compares methods of statistical analysis of the information relating to the evaluation of an asbestos deposit. From a study of 10-ft. lengths of drill core, the separate effects of visual evaluation errors were determined, as well as the deviations between evaluators and the deviations produced by a slight displacement in the center lines of the check drill holes. The importance of careful statistical analysis of such information is stressed.

Jan 1, 1966

By R. K. Borden

Rio Tinto is committed to proactive mineral waste and acid rock drainage management. Corporate requirements are closely aligned with the GARD Guide principles of early geochemical characterization and prediction followed by selection and implementation of management strategies to prevent or minimize ARD. Each operation is required to design and implement an ARD and Mineral Waste Management Plan. Successful implementation of the plan requires commitment at all levels of the company, from senior management, to geologists, mine planners, environmental staff and equipment operators. Examples of the successful integration of ARD management strategies into mine operations are cited from several mines.

Jan 1, 2011

By Harold J. Bennett

The purpose of this study was to develop methods for the financial evaluation of mineral deposits. This includes the selection of the best alternative mining and processing methods and production rates. This was done by performing a financial evaluation through computer simulation using sensitivity and probabilistic risk analysis. The criterion used to measure the relative advantages of these investment and operating alternatives is the discounted-cash-flow rate of return. Included is a description of the theory and methods used in the probabilistic analysis approach, which is based on the premise that the expression of a range of values in establishing an estimate for a parameter is more realistic than the choice of a single value. Numerous simulations are made using randomly selected values of the input parameters resulting in a frequency distribution of the rates of return and their relative probability of occurrence. The sensitivity analysis method is described and combined with the probabilistic analysis to interrelate mineral reserves, capital investments, operating costs, and production rates. The ability to vary these input parameters on successive runs has permitted the selection of the best alternative mining and processing methods and production rates for a given mineral deposit. For illustrative purposes the evaluation of a mineral deposit was performed using three alternative mining and processing methods at three different quantities of resources and various production rates and prices. The computer program used in this analysis was written in FORTRAN II for maximum compatability and should run without modification on most computers having BK (8,000-word) core memory, a card reader, and printer (120 characters per line).

Jan 1, 1970

This report describes Phase I of the project --Development of a Mechanized Scaler --performed by Battelle, Pacific Northwest Laboratories for the U.S. Bureau of Mines. The objectives of Phase I were to 1) assess the needs of the industry as related to mechanized scaling; 2) conceive, evaluate and select mechanized scaler concepts; and 3) prepare preliminary designs of the selected machine concepts. To assess the scaling needs of the industry, we reviewed both U.S. and foreign literature, evaluated U.S. scaling accident statistics, reviewed existing mechanized scaling equipment, performed a series of mine visits and telephone interviews with mine operators, and assessed the applicability of a loose-rock detection system. The literature review identified over 25 scaler-related articles. However, little of the information could be used directly in the conceptualization and design portions of the project. Three articles did supply information on a number of machines used in Europe, along with statistics describing their effect on mine safety. For example, the French reported a 50% reduction in the total number of scaling-related accidents and a full 80% reduction in the number of lost-time injuries in the Lorraine mining district.

Jan 1, 1981

By Yunsheng Yao, P. Golledge, A. D. S. Gillies

In order to investigate the explosibility of sulphide mineral dusts, sulphide ore samples were collected from five underground metalliferous mines in Australia. The mineralogical and chemical composition of the dust samples was analysed by X-Ray Powder Diffraction and Atomic Absorption techniques. Simulated post detonation fumes were produced and used in dust explosibility tests to examine the influence of the fumes on sulphide dust ex- plosions. These tests were conducted in a 20 Litre Siwek Explosion Chamber with measurement and control system that is regarded as a standard testing system worldwide for dust explosion studies. The dust mineralogical composition and dust explosibility tests indicated that the content of sulphur can not accurately predict the explosibity of the sulphide dust. The percentage content of pyrite in the sulphide dust can be a relatively reliable diagnostic criterion in evaluating the risk of sulphide dust explosions in the mining of a massive sulphide orebody. The hybrid explosion tests demonstrated that the post detonation fumes from ANFO not only decrease the lower explosion limit of the sulphide dusts, but also increase the severity of the dust explosions. The explosion pressure reaches its peak value when the fumes content in the explosion chamber is about 20 per cent by volume

Jan 1, 1997

By C. Richard Tinsley

Like most minerals, coal is inherently a demand-limited commodity. The very sedimentary nature of its occurrence implies greater availability potential than demand. But this situation is overridden by economics among fuels, between coals, and within coal blends. Such considerations make coal forecasting a very hazardous profession indeed. THERMAL COAL If one thought that the lead times involved with a mining project were very long, one has obviously not been exposed to the planning process in the electric generation business - a process seriously confounded by shifts in load growth, environmental pressures, capital intensity, security of fuel sourcing, inter-fuel economics, and so on. But as a general rule, the near-term forecasts for thermal coal can reliably be based on a bottom-up, plant-by-plant analysis. Cement plant conversions can also be reasonably estimated next in order of reliability, although they have a much wider spectrum of coal qualities and fuel sources to choose from with a notably higher tolerance for sulfur and ash. Finally, industrial demand can be assembled from the estimates for conversions by pulp/paper plants, chemical plants, etc. The industrial sector is harder to estimate, since it may involve small boilers or dual-fired units. Assessing demand in the Pacific Rim is relatively a straightforward process in the near term because the major importing countries are all located on the Asian continent with either negligible or very minor (yet stable) indigenous coal production, (itself often operated on a subsidized basis). Furthermore, all imports are seaborne. These major importers are Japan, Korea, Taiwan, and Hong Kong with Thailand, Singapore, and Malaysia up-and-coming consumers. The suppliers to this market all have substantial reserves to back up decades of exports to these countries. Australia, the US, Canada, South Africa, China, and the USSR dominate the supply side. The second oil-shock of 1979/1980 has convinced the importers that reliance on oil can be expensive and eminently interruptible. Thus, they are determined to diversify away from oil' to nuclear and coal for generating electricity and for coal for other purposes where possible. This trend is seen to continue even in the face of the oil glut worldwide and oil-price reductions in early 1982. But the importers are also convinced that reliance on one coal source and, in particular, one infrastructure route for the coal chain from mine to consumer can be equally expensive and interruptible. Strikes in the US and Australia; excessive demurrage at certain ports; relegation of coal to a lower priority on multiple-use railroads in the USSR and China; and concern over escalation on high-infrastructure or high-freight coal chains are among the risks worrying the importers. As a consequence, Pacific Rim thermal coal purchases are being allocated among supplier nations, between ports, and within each country. An example of Japan's shift away from Australia and toward the US and Canada is shown in the estimates in Table 1. But the confidence of the import estimates deteriorates sharply beyond the plant conversion timetables and construction schedules in the near term. If part of the second generation of coal-fired power plants can handle lower-energy coals, the field of suppliers could widen to accept sizeable tonnages from Alaska, Wyoming, Alberta, or New Zealand resources. These supply sources generally have some infrastructure or freight advantage to compensate for their lower quality and to compete on a delivered energy-unit basis. These also offer diversification in sourcing. And the possibility of coal liquefaction in Japan further widens the sourcing network. A great number of Pacific Rim coal forecasts have been generated, especially for Japanese thermal-coal imports which are expected to grow strongly in the 1980's. Since the Japanese themselves have not yet settled their energy policy, the exact numbers are hard to call. Nevertheless, at 50 million tonnes of imports in 1990, Japan would consume 50-60% of the total Asian thermal coal imports as shown on Tables 2 and 6. The next most important consumers are the "island" nations of Korea, Taiwan, and Hong Kong (see Tables 3-5). All three are embarking on power plant developments usually with captive unloading facilities, capable of accepting more than 100,000-dwt vessels. Korea, with no-indigenous bituminous coal, is not especially enamoured with US coals, which are deemed too heavily loaded by freight and infrastructure costs -- up to 70% of the delivered price. Thermal coal contracts are presently split to Australia (70%) and to Canada (30%). Korea Electric Power Co. is already considering second-generation boilers capable of burning lower-quality coals than the present standard. Korea does burn domestic anthracite.

Jan 1, 1982

By M. Kaitz

A continuing discussion in both the petroleum engineering and economic literature is directed to the difficulties encountered in the use of discounted cash flow rate of return (DCF) as a measure of investment worth. Although useful in most Instances, DCF has been criticized because it is time-consuming in its trial-and-error solution, theoretically invalid, not adaptable to cash flow streams yielding multiple return solutions and not entirely reliable in selecting between mutually exclusive investments. The theoretical invalidity of DCF stems from the reinvestment assumption implicit in the calculation that earnings are reinvested at the DCF rate. The emerging consensus of the economic literature is that the net present value or the present worth of the net cash flow stream (discounting at the average opportunity or cost of capital rate) is more correct and reliable. Other criteria proposed have been ratios of net present value divided by initial investment or by present value of all investments in a project. All of these criteria are simple to determine and explicitly assume a reinvestment rate for [he income generated by a project. This paper develops and discusses a theoretically valid profitability criterion which is simple to compute and retains the appeal of a percent return on investment. It is called "percentage gain on investment" or PGI. It measures the gain an investment is expected to realize over like capital invested in the average opportunity and explicitly considers reinvestment potential. Why add another Concept to the large array of investment criteria now available, any one of which, or perhaps a combination of several, appears to embrace the form's (or individuals) objectives? The answer is that not one of the existing criteria provides both a readily comprehensible and theoretically valid measure of risk coverage that has general application. The proposed PGI does fulfill these requirements. INTRODUCTION An ancient expression warns that "one must yield to the times" — there are better ways of doing things. A review of the petroleum engineering and economic literature on one topic alone, measurement of investment worth, certainly is witness to this truth. In use for a number of years, the DCF has recently received attention, directed mainly to its theoretical invalidity. Several alternatives to DCF have been proposed to provide a valid, simply determined criterion to describe investment worth and to overcome the criticisms previously mentioned. This paper introduces another method called percentage gain on investment (PGI) and is proposed as but one of several yardsticks that should be used in making investment decisions. MEASURES OF INVESTMENT WORTH This paper will consider only those criteria which give weight to the time pattern of future earnings. These criteria are usually compared with an average opportunity rate or cost of capital of the firm to judge the relative worth of the investment. For purposes of demonstration, a 9 percent average opportunity rate will be used throughout this paper. Implicit in the DCF calculation is the assumption that earnings are reinvested at the DCF rate. Some argue, though, that there is no reinvestment assumption,' that the DCF rate is simply that maximum rate of interest one can pay on the investment over the life of the project and break even. The determination of DCF is accomplished by discounting the net cash flow stream at that rate (DCF) which will yield zero. The question is: why should reinvestment potential be explicitly considered in calculating return on investment or other criteria measuring economic worth? Perhaps the answer lies in consistent or equal treatment of future cash flow. It appears entirely illogical to give different present worth value to $1 received, say, 10 years from now, which is the circumstance resulting in comparing projects with different DCF returns. In fact, $1 received in 10 years has the same value regardless of which project generated the income. DCF return thus favors investment projects which are expected to provide early income as compared to those providing long-term income. Not surprisingly, the controversy on reinvestment assumption is an old one. Hoskold' discussed this same problem in 1877. He considered the future income from mineral properties as an annuity or a series of fixed future payments. (As will be demonstrated, his equation can be modified for variable income.) Prior to Hoskold, the value or what one could pay for the mine, was determined with the use of standard, single-interest tables. Here is what Hoskold said with regard to these tables. "This table, and others of its kind, to be found in most works on annuities, is constructed correctly according to

By L Dyer, G. J. Wilkie, P. Walters, B Tadesse, L. Keeney

Grade Engineering® is a term trademarked by the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) and includes five key levers for upgrading ores and rejecting waste prior to expensive downstream comminution and mineral processing. These five levers include natural deportment, induced deportment, bulk sorting, particle sorting and gravity separation. Over the past ten years, CRC ORE has progressed a range of technologies that exploit these levers from laboratory proof of concept through to large scale demonstration and validation. This paper details the work carried out by CRC ORE and Curtin University for assessing the amenability of an ore for its natural deportment and particle sorting attributes in an Integrated Screening and Particle Sorting (ISPS) Grade Engineering® process. ISPS is seen as a preferred method for Grade Engineering® as compared to individually operated unit operations as the benefits of each can be complementary. Furthermore, it is suggested that integrating the two levers has two important impacts: 1. Firstly, there is a risk that isolated particle sorting test results will be misinterpreted as being representative of the full sample without considering the mass balance impact of high-grade material that might have been lost in the fines fraction. This fine fraction will not be detected through the particle sorter. 2. Secondly, and potentially of more valuable impact, is that the opportunity may exist to upgrade the feed first through determining if there is a concentration of high grade to the fine (or coarse) fraction which can be separated through screening. Undertaking screening in the preparation stage of the particle sorting process will enable analysis and separation of the fine or coarse fractions of a rock mass. The result of this study provides the mining industry with an independent framework for undertaking an Order of Magnitude (ISPS) Grade Engineering® assessment on a range of constituent ore types. Keywords: Grade engineering, particle sorting, grade by size fractionation

Jan 1, 2020

By Carlos G. Levi

"The principles involved in the rapid solidification of supercooled metal droplets and existing numerical models are reviewed. The limitations of these models for studying alloy solidification are discussed in terms of the effects of alloying elements on the relevant heat transfer, thermodynamic and kinetic parameters. Analysis of the enthalpy-temperature diagram reveals how the extent of rapid solidification is hindered by the addition of solute. A solidification model incorporating thermodynamic and kinetic relationships into a Newtonian heat transfer formulation is used to analyze the thermal history and concurrent solute redistribution during recalescence. IntroductionIt is well acknowledged that microstructural evolution during solidification is intimately associated with the thermal history of the liquid-solid interface. Structural parameters like chemical homogeneity, morphology and size scale of the phases can be related to the interfacial temperature and velocity. These in turn change by the interaction of the interface with the thermal and solutal fields in its neighboring environment.The thermal history of powder solidification can be conveniently described on the enthalpy-temperature diagram for a pure metal shown in Figure 1 and discussed in detail elsewhere [1). A system can conceivably follow any path of decreasing enthalpy in the supercooled region of Figure 1 (~ < 1), starting at the nucleation temperature (oN < 0) on the liquid line, and ending at some point on the solid line. A vertical path represents an isothermal transformation, of which a limiting case is solidification without significant barriers to nucleation and growth, with the interface at the equilibrium temperature TM (path one in Figure 1). A horizontal path represents isenthalpic (or adiabatic) solidification whereby the system could form an amount of solid proportional to the initial supercooling of the liquid without further heat loss to the environment. A liquid that can completely transform to solid under adiabatic conditions is said to be ""hypercooled""."

Jan 1, 1986

By J. N. Van der Merwe, M. Mathey

"The development and mechanical characterization of coal-crete, a composite material generated from coal fragments and some binder material, is described in this paper. Coal debris was obtained from a colliery in South Africa. The binder used in the study basically consists of cement and water, and further ingredients are added to the mixtures, such as sand, fly ash and polymers, in order to investigate alterations of the mechanical properties of coal-crete.Results from over 220 mechanical tests on coal-cretes with various binder mixtures give consistent trends for the material’s behaviour. Linear relationships are suggested between the uniaxial compressive strength, Young’s Modulus and the indirect tensile strength of the coal-crete.It is shown that mechanical properties comparable to coal can be achieved. Coal-crete is therefore suitable for physical modelling of mining situations in experimental studies and for use as backfill in underground coal mines. The latter application is particularly attractive when refuse coal is used as aggregate material. The indicated trends in this study may be used as a guideline for individual coal-crete design needs. However, some uncertainty remains as to the influence of particle shape, size and gradation, coal rank and age of the coal-crete. These aspects are recommended for further research."

Jan 1, 2015

By B. Panton, J. Carvalho, E. T. Brown

"A major consideration in the design of high capacity tiedown anchors for dam, bridge and tower foundations is the tensile resistance of the rock mass to pullout, typically as a result of overturning moments or hydrostatic uplift. Rock mass pullout capacity for installed anchors is developed from the tensile strength and fracture propagation properties of intact rock, the orientation and physical properties of the discontinuities and anchor confinement at depth. The typically assumed, but generally conservative, design approach is to calculate anchor pullout capacity using the dead weight of a uniformly shaped inverted “cone” with an assumed initiation point and breakout angle. In some cases, some tensile or shear strength is considered across the area of the assumed pullout cone, however, these strength estimates are based primarily on based on limited historic testing data, empirical relationships for rock mass strength developed for other applications, and engineering judgement.As an alternative to the current foundation anchor design method, this paper presents a new approach to the rock cone pullout problem using Discrete Fracture Networks (DFN) combined with numerical simulations. The simulations presented in the paper investigate the influence of fractures in a synthetic rock mass on ultimate anchor strength. In addition, the global influence on fracture network statistics on rock mass pullout failure is also discussed and it is contended that some of the aleatory and epistemic uncertainty inherent in the design of rock anchors can be reduced by considering fracture statistics in anchor design."

Jan 1, 2015

By Jardine G, Woodall C

The Henty Gold Mine, located in Western lasiuania use, uuiusatise solutions to effectively manage a mining operation in an environmentally sensitive setting and has been presented with several environmental awards. Fill is required as part of the mining method to provide passive ground support, minimise rock exposure and ensure maximum recovery of the small but high-grade orebody. The use of the whole portion of leach residue in the backfill reduces the surface tailing disposal requirements. Therefore, High Density Paste Fill (HDPF) has been selected as the most appropriate fill method to meet these objectives. Additional benefits include the minimisation of excess water from fill and the subsequent need for the collection and treatment of water and slimes. There are minimal equipment requirements during placement, thereby optimising mine resources for production. The initial paste fill design was based on the Bad Grund and Ranunelsberg Mines paste fill systems of Preussag in Germany and comprised pumping filtered tailings paste some 1.2 kin uphill from the mill to the mine portal, where cement was to be added before being distributed underground. The system was designed following initial testwork that was undertaken on a bulk sample of ore mined from the scar surface Sill Zone. Subsequently, during the mining of the Zone 96 orehody, it was found that there were significant mineralogical variations in the composition of the ore mined. Following processing, the resultant Icach residue caused significant changes in the paste rheology and therefore the pump and flow characteristics. An alternative solution was implemented that involved the use of agitator trucks to transport the cemented paste to the portal. This required modifications to the fill preparation system and also the underground distribution system. Laboratory strength tests of the HDPF using actual gold plant leach residue showed low early strengths were attained with HDPF containing only filtered leach residue. Therefore, high binder addition rates or an increase in the fill cycle time would be required to allow the fill to gain sufficient strength. A considerable amount of potentially acid generating waste rock also requires underground disposal. By blending the waste rock with the HDPF, the strengths were improved and the required cement addition rate reduced by about one-half. The potentially acid funning waste rock is encapsulated in the highly alkaline cemented paste, minimising the potential for acid generation.

Jan 1, 1998

"Conveyed coal flows have been diverted on the basis of real time ash analysis since the 1980s. Many coarse particle separation methods are available through screens, jigs, heavy media separation, particle sorters, to name a few, however bulk diversion requires a representative, continuous analysis to ensure diversion decisions can be made with confidence. Sensors also need to be able to provide measurements at useful time increments so that small tonnages can be diverted for maximum selectivity. Particle separation typically requires high capital costs and there are limitations either in throughput tonnage or particle size or both. Few techniques are able to provide robust and representative analysis of conveyed flows in a useful time basis. Prompt Gamma Neutron Activation Analysis provides multi-elemental analysis of conveyed bulk materials and has been proven in the minerals industry since 2003. This paper outlines the success of this technology in minerals applications in iron ore, phosphate rock and most recently in copper-gold ores, including its use in bulk diversion.INTRODUCTION Naturally occurring quality variability, or heterogeneity, in mineral deposits enables separation and recovery of the valuable components through mining and processing operations. There are distinct advantages in processing the minimum quantity of material to achieve the highest possible yield. Unfortunately, declining ore grades has resulted in larger scale operations and a subsequent loss in selectivity for mining operations. As limits are approached on the practical size of equipment, there is more motivation to investigate alternative solutions. Mining companies are subject to increasing social resistance to growing waste disposal requirements in addition to higher energy and transport costs. Major savings are available by reducing the quantities of material processed where pre-concentration can be effectively applied at early stages in the process. One of the simplest ways to pre-concentrate is to measure the bulk material and reject waste soon after mining so that minimal expense is incurred and that only higher quality material is sent to processing operations. This bulk sorting can occur within the mining operations and has major benefits through energy and other consumables savings. This paper discusses the application of real time analysis technologies suitable for bulk sorting within the minerals industry. Technology that has proven representative for conveyed material bulk analysis and its successful applications to date is explained. Analysis using a sensing technique is only one component of a successful bulk sorting process; the importance of effective diversion systems and a bulk sorting strategy are also discussed. The bulk sorting stage may be one component of a system that could include additional downstream technologies such as particle based sorting systems on a diverted stream."

Jan 1, 2018

By M. L. Brashears

Pine Point Mines is located in the Northwest Territories of Canada, about 500 miles north of Edmonton, Alberta (figure 1). Lead-zinc ore is found in numerous localized deposits along a generally east-west trending reef of Devonian dolomite, about 5 miles south of Great Slave Lake. A pumping-test program was carried out in 1968 to guide the design of dewatering systems for several open pits that are partially or wholly below the natural ground-water levels. The hydrogeologic conditions, methods employed and results obtained are discussed.

Jan 1, 1971

By Brad Simser

Several case histories from Glencore’s Sudbury Operations show how passive seismic monitoring data is used for geotechnical decision making. The data comes from three different seismic arrays monitoring two open stoping deposits, and a narrow vein cut and fill/blasthole operation. Mining depths range between 1000 to 1680m below surface. The deposits are hosted in hard igneous rocks typical of the Sudbury basin, with characteristically high horizontal stress (approximately 1.8 times the depth of overburden). Rockbursting is the main geotechnical risk, due to the strong brittle nature of the rock and local high mining extraction. Fault related seismicity includes both fault slip events, and the stress channelling effect as the mining front approaches a major fault structure. Planar data trends generally line up with known faults and often indicate early stage fault activation. The structures are risk ranked based on their seismic response. This has been particularly useful at the Nickel Rim South Mine (NRS) where the structural fabric (jointing and small-scale faulting) is generally parallel to the more through going faults. The persistence of structures is difficult to measure, and the NRS faults generally have low offsets and thin gouge. The visual difference between the more persistent structures that occasionally generate large seismic events (up Mw 2.9 to date) and localised joints/slips is often minor. The seismic monitoring data clearly shows the more active structures. This information is highlighted on mine plans to help guide enhanced ground support and seismic re-entry protocol barricade locations. Pillar loading/yielding is a key element to the blasthole operations where a primary/secondary mining sequence is used. The secondary pillars are mined in a yielded state with just-in-time development. An example of the seismic signature of a secondary stope is shown with emphasis on the need for high location accuracy given the stope widths of 12.5 to 15m. The ratio of the shear wave energy to primary wave energy (Es/Ep) has long been used as a method to estimate source mechanisms; the higher the ratio, the more likely the event is fault slip versus rock fracturing. Data sets are filtered on Es/Ep ratios to highlight both fault slip populations and stress fracturing mechanisms. Examples of seismic data quality checks, high stress development, and re-entry protocols are also shown in the case histories.

Apr 26, 2022

By D Davis

The prediction of ground-borne noise levels from tunnel construction activities requires knowledge of the input vibration forces from the vibration source(s) into the cutting face, knowledge of the vibration transmissibility through the surrounding medium, and knowledge of the receiver building’s vibro-acoustic response. The conversion of this vibration energy into sound pressure within the receiver building depends upon the vibration coupling of the soil and the building’s foundations, the structure’s response including floor-to-floor attenuation and amplifi cation due to resonance, the radiation effi ciencies of the internal structural elements, and the room’s acoustical properties. Beginning with a known input vibration spectrum at the cutting face, it is possible to predict the resultant ground-borne noise levels within a receiver building using either analytical and/or empirical techniques, or by numerical modelling. This paper presents an overview of the various methods available to estimate ground-borne noise levels from tunnel construction activities and discusses the advantages and limitations of each.

Mar 8, 2011

By M Edwards

The paper outlines the successful application of some of the on-belt technologies available from Scantech International Pty Ltd and how these have provided benefits in a number of mining and mineral processing operations. Effective process control requires real time analysis so quality can be fed back to the previous process and fed forward to a subsequent process. A range of on-belt analysers that allows for full stream, continuous, non-contact analysis of conveyed materials is available to achieve this. Real time results can provide timely information for effective process control. Benefits of on-belt analysis systems become more evident once the true variability of material quality and moisture content in conveyed flows is measured. To obtain economies of scale in mineral processing operations large material flows are achieved using conveyors. The cost and effort to sample representatively increases as conveyor flows increase. One sample may represent a few tonnes or up to 10 000 tonnes of material. The turnaround time between sampling and availability of sample analysis data does not allow real time process control. Tonnage flow rate, moisture content and elemental or mineralogical composition are required to perform effective process control of most conveyed streams. Tonnages can be effectively measured using belt weighers. The analyses derived from small samples supplied by conveyor-based sampling systems contain high variability. On-belt, continuous analysers see all the material and, through short term compositing of analyses, supply less variable results. Real time analysis helps operators develop a better understanding of material variability. Analysers can be effectively utilised to improve the consistency of product quality through bulk sorting and blending control. Many existing users of the technologies have gained competitive advantages through their ability to supply a more consistent quality product to the market.

Jan 1, 2008

By K M. P Singh, K M. K Sinha, G S. Jha, T Gouricharan, K K. Sharma

The majority of the powerplants in India are fed with non-coking coals, with the coals dispatched from their respective mines via wagons loaded by a rapid loading system or pay loader. The usual top size of coal is 200 mm and sampling is carried out manually from wagons. The manual method of wagon top sampling of large size raw coal is not only difficult, but also violates some of the fundamental principles of sampling. As per sampling requirements, samples are to be drawn from the full depth of the wagons, which is impossible to be done manually. Since the ash distribution in the different size fractions is not homogeneous, the results from the samples, which do not reflect the true size distribution of the lot, are likely to be biased. More importantly, sample collection by shovel from the top is a function of human discretion and not governed by the equiprobability rule. In another case, the sample has been collected by a cross belt-type auto mechanical sampler for 200 mm size coal at one of the super thermal power stations. Test analysis shows that coal collected using a cross belt-type mechanical sampler also has significant deviations from stopped belt coal samples of 200 mm size due to size segregation. Studies carried out on wagon top sampling through specially designed experiments reveal some interesting features. The presence of bias in wagon top sampling is apparent when compared with the ‘stopped belt’ sample. In this paper, a comparative study between manual wagon top sampling/auto mechanical sampling with respect to stopped belt sampling has been conducted for coal of size 200 mm. In addition, precision studies have been performed for wagon top sampling/mechanical sampling for Indian thermal powerplants.CITATION:Sinha, K M K, Sharma, K K, Jha, G S, Singh, K M P and Gouricharan, T, 2014. A comparative study of manual wagon top sampling and auto mechanical sampling of 200 mm size coal with respect to stopped belt sampling of thermal coal at Indian super thermal powerplants, in Proceedings Sampling 2014 , pp 43–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014