Search Documents

By M. Mpofu, G. Stenzel, F. Magweregwede, B. Maphalala, T. Kgarume

Surface coal operations in which mining activities are conducted above old underground workings experience hot holes after drilling. In a coal mine, hot holes are defined as shot holes, which after being drilled have an in-hole ambient temperature of 40°C or above or show a temperature increase of 3°C or more during monitoring. Hot holes and other cavities, such as cracks, pose health and safety risks to workers, such as exposure to hot air and high concentrations of noxious gases released from these holes. In addition, workers may be exposed to premature detonation of explosives caused by in-hole temperature increases and chemical reactions. To this end, Coaltech Research Association commissioned a project to develop a Best Practice Guideline for the management of hot holes. This paper is a compilation of the activities conducted in the development of the Best Practice Guideline between 2021 and 2022. The activities included a review of standard operating procedures and hot-hole temperature-measuring and -monitoring devices, and the assessment of current hot-hole procedures at selected mines. The results indicated that management of hot holes requires a focus on pre-emptive risk assessment of mining blocks, identification of hot holes using the correct temperature-measuring devices, and continuous monitoring of hot holes from the time of drilling until just before blasting. Hot-hole management accessories, such as polyvinyl chloride sleeves, were found to be effective in insulating the hot-hole emulsion from the rock mass temperature, thus preventing the potential for premature detonation.

Sep 9, 2024

By E. Chiyangwa, L. Schoeman

The commercially successful electrowinning and refining of metals typically requires the optimization of the electrolyte composition and operating parameters to produce high quality compact electroplated metal. The prediction of the effect of the electrolyte composition on the structure and morphology of the plated metal remains a challenge. Initial work on the use of polarization measurements to predict and control plating behaviour in electrowinning plants involved potentiodynamic polarization but proved unsatisfactory as accurate and repeatable predictions could not be achieved. The aim of the present work was to develop a reliable galvanodynamic technique specifically applicable to the plating of zinc from sulfate electrolytes with which plant operation may be controlled and optimized. Initial results indicated that plating and nucleation potentials could be measured accurately and repeatably and that the relationship between the two could be used as a predictive tool for the effect of electrolyte composition on the quality of zinc electrodeposits.

Jan 1, 2014

This publication summarizes the research (in-house and contract projects) programmed by the Bureau of Mines for fiscal year 1985 (October 1, 1984-September 30, 1985) under its Health and Safety Technology Program. The objective of these projects is to provide an ordered and sequenced advance toward the Bureau's overall goal of providing the system technology required to create a more healthful and safer working environment for the Nation?s mining and minerals processing workers.

Jan 1, 1985

By Walter W. Kaufman

The braking performance of underground, rubber-tired, non-coal mining vehicles is evaluated. Surveys of mining equipment and braking manufacturers and underground stopping tests are discussed as they relate to this evaluation. Stopping performance recommendations are included as well as related aspects of roadway construction and runaway vehicle protective devices.

Jan 1, 1977

By George H. Bodfish

This paper begins with a short history of air compressors, emphasizing their "roots" in the mining industry. It then describes the types of compressors available, including reciprocal, the various rotary positive-displacement compressors, and the centrifugal. The advantages and disadvantages of selecting a certain type of compressor over another are enumerated, considering customer requirements and operating costs, among other factors. Guidelines to operation and maintenance are discussed, including installation, monitoring and maintenance procedures. Finally, the paper addresses itself to future trends, with special attention being given to the system concept, the increasing use of rotary compressors, power consumption, reliability, packaging and noise attenuation.

Jan 1, 1978

By IPMI Educational and Scientific Foundation

It is with great pleasure that we announce the availability of this fourth issue of the IPMI Journal, a publication of the International Precious Metals Educational and Scientific Foundation. This digital peer reviewed publication has been created as a vehicle for the sharing of technical information related to the science and technology of precious metals. Since 1976, the International Precious Metals Institute has championed the exchange of information of critical importance to the precious metals scientific and commercial communities through its various communications vehicles. This has included instructional videos, annual conference symposia, special topic committee meetings, regional seminars, and professional and student achievement awards. Due to the breadth of important topics related to all aspects of precious metals, it has been the vision of the IPMI to provide a publication available to the general public that would become a key source of pertinent topics containing high quality publications by experts in their fields of study. Historically, the IPMI has attracted world renowned experts in many fields (including Nobel Laureates Henry Taube, Ei-ishi Negishi, Robert Grubs, Professor Ben Feringa, and David MacMillan) in the dissemination of discoveries, inventions, and industry proven practices. Such information has a total value greater than the sum of its parts as seemingly unrelated innovations from distinct focus areas can be adapted to solve problems. Because of this important characteristic of information exchange, we have decided to create a digital journal, available to the general public, that will not only communicate state of the art discoveries and sound practices, but will also review historical communications from the IPMI’s archives that have value and use even in today’s environment. On behalf of the members and leaders of the IPMI, we hope you will find value in this new publication.

Dec 1, 2022

By Raymond W. Hiteshue

To aid in designing a continuous system for evaluating processes for converting coal to high-Btu gas] the Bureau of Mines determined the amenability of various coals and a char to hydrogasification at 800° C and 6,000 psig using a molybdenum catalyst. A lignite from Rockdale, Tex., an hvCb coal from Rock Springs, Wyo., a char from the low-temperature carbonization of the latter, an hvAb coal from Pittsburgh, Pa., and an anthracite from Luzerne County, Pa., were selected. Highest yields of gaseous hydrocarbons, 94 pet, based on maf feed, were produced from char, and lowest yields, 67 pct, were obtained from lignite. Hydrocarbon gases contained 82 to 92 pct methane, 8 to 15 pct ethane; and 1 to 3 pct propane.

Jan 1, 1962

By E. J. Burrough

Coal Reserves The Crowsnest Pass coal fields form part of a greater area which comprises the Inner Foothills belt of the Alberta coal fields and the southeastern coal fields of British Columbia. The most valuable and most extensive reserves of the bituminous coals of Canada are concentrated in this?area, of which the Crowsnest Pass fields form an important part. The extent of these coal reserves together with those of the rest of Canada were recently studied by the Geological Survey of Canada for the Royal Commission on Coal of 1946 (1). Quotin from the report, it is of interest to note that, prior to this work, the most widely known, and in fact the only Canadian-wide estimates of, coal reserves of Canada available to the Commission were those prepared by Dr. Dowling in 1913 (2). At that time it was estimated that Canada's reserves of coal were over twelve hundred billion tons. The more recent estimates of mineable coal for the whole of Canada are of the order of 10 per cent of that figure and are reported. as 99 billion tons, which is further reduced to 40 billion tons on the basis of the estimation of recoverable coal. This considerable divergence in estimated reserves is explained in part by the big difference in the bases of measurements. For example, in the original report, seams of one foot occurring at a depth of 4,000 feet were included in the estimates.

Jan 1, 1951

By J. F. Messerly

The purity of three specially prepared samples of benzene was determined with an adiabatic, low-temperature calorimeter with automatic control of shield temperature. Extensive measurements were made on each sample to determine how variations in operating procedures affect melting-point and freezing-point as well as purity data obtained by the calorimetric method. Detailed results of the investigations are presented, and effects of different operating procedures are discussed, together with problems encountered in interpretating experimental results.

Jan 1, 1963

By S. Seetharaman

In the processing of molten metals, it is extremely important to monitor continuously the concentration levels of various minor elements, In the production of common metals like copper, iron and aluminium electrochemical sensors involving solid, as well as liquid electrolytes are being increasingly used to measure the concentrations of minor elements The present paper deals with the electrochemical principles underlying these measurements and the possible errors involved. One of the major difficulties in the case of the solid electrolytes is to correct for the consequences oldie electronic contribution to the conduction of the electrolyte. The application of the electrochemical sensors for molten metals processing involves designing of these probes to withstand the industrial operating conditions. In this respect, significant achievements have been made with respect to the design of oxygen probes for liquid metals in general and liquid copper in particular. Some of the salient design features are discussed in the paper, The application of auxiliary electrodes for impurities in molten metals like phosphorus in copper and silicon in iron are taken up. The development of oxygen sensors for slags is given special attention. Recent developments' in the field of sensor technology, as applied to metals processing are highlighted.

Jan 1, 1996

Possible consequences of continuing internal political unrest and the imposition of foreign sanctions raise concerns about the traditional reliability of the Republic of South Africa as a major world supplier of important minerals. A recent Bureau of Mines' technical report (Open File Report 76-86) examined the impacts of temporary peacetime disruption scenarios for six key materials and mitigating options. Because of South Africa's dominant producer position for these minerals (except for cobalt), expansion of primary production capacity outside of South Africa is not a short term mitigative option. However, prospects of a longer term disruption would likely spur investment in capacity expansion in alternative Market Economy Country supply sources. This report identifies the resources, production costs, and burdens that would be placed on alternative MEC producers of chromium, cobalt, gold, manganese, and platinum-group minerals if South Africa's production were subject to a long term; disruption. When long term supplies from South African deposits are discounted, more than a few years reserves were found only for cobalt and manganese. Even for these two minerals, higher sustained prices would be required to increase manganese production capacity and to support means of cobalt transportation not through South Africa.

Jan 1, 1986

By Arno C. Fieldner

From July 1, 1949, to July 1, 1950, the Bureau of Mines conducted the research and technologic work on coal and coal products that is summarized in this report. The research, described in this fifteenth of a series of resumes, is presented in more detail in publications (see footnote references) that appeared during the fiscal year, though in some cases research data are given that have not been published elsewhere. Results of research in the experimental coal mine, on explosives, and on gas and dust explosions will be found in Bureau of Mines Report of Investigations 4228, Annual Report of Research and Technologic Work on Explosives, Explosions, and Flames, Fiscal Year 1950. An over-all view of our coal, oil, end natural-gas reserves was presented, and the future possibilities for the, production of synthetic liquid fuels from coal were delineated.3/

Jan 1, 1951

By D. G. Klaren, E. F. de Boer

Self-cleaning fluidized bed heat exchangers have demonstrated unparalleled performance internationally for the implementation of indirect heat transfer in severely fouling fluid environments. The ingenious configuration of recirculated cleaning particles through the tubes of vertical shell and tube heat exchangers provides the ability to solve any problems that arise as a consequence of tube-side fouling during indirect heat transfer to process fluids or slurries. In most cases, the cleaning particles consist of chopped metal wire, however other process-specific materials have been used. In addition to the mitigation of fouling effects, a number of other significant benefits for slurry heating are afforded by the mode of operation of the self-cleaning fluidized bed heat exchangers. Increased turbulence at the slurry/tube interface is imparted by the action of the fluidised particles, resulting in very high heat transfers at relatively low liquid velocities. Furthermore, given the thixotropic nature of most process slurries, the action of the fluidised particles imparts additional shear to the process slurry, resulting in shear thinning effects with a consequent reduction in pressure drop and enhancement of heat transfer across the heat exchanger. The benefits provided by the self-cleaning fluidized bed heat exchanger make it the ideal option for the indirect heating of laterite nickel slurry for High-Pressure-Acid-Leach (HPAL) plants. This article explains the principle and application of the self-cleaning fluidized bed heat exchanger technology for the processing of laterite nickel and cobalt slurries in HPAL plants. It also presents an elegant method to revamp existing direct heated laterite nickel and cobalt processing plants into an indirect heated configuration employing self-cleaning fluidized bed heat exchangers.

Jan 1, 2004

By W. Gibson Jaworek

It has become apparent in recent years to everyone intimately concerned with the future of the American fuels industries that the growth in demand for energy has become a topic receiving considerable attention, and that investigators are leaning more and more toward a mathematical approach to deduce what pattern that growth will follow. Though coal has been included by necessity In all-studies of future energy markets, it has not been the subject of mathematical analysis or description as frequently as has been total energy or some of the other fuels, particularly petroleum, It is the intent in this particular paper, to subject bituminous coal consumption to a preliminary mathematical scrutiny which can lead to a more logical estimation of the general level of bituminous coal consumption for the next decade, as well as formulating an approach toward describing how coal consumption may vary as the result of the annual variations in activity in the United States, economy, The approach utilized is more sophisticated than the mere projection of the historical trend of bituminous coal consumption. Such a projection would lead to a continuation of the recent decline, indicating that coal consumption would reach zero some thirty years from now. On the other hand, the mathematical analysis described here is a relatively simple, straightforward approach and- is not intended to represent the-ultimate in mathematical economic analysis as now practiced, It is hoped that this will contribute to our knowledge of bituminous coal markets. Even more, it is hoped that it will help arouse a greater interestin utilizing mathematical and statistical analysis when studying the bituminous coal industry. - Since this is a preliminary study, comments and criticisms are anticipated.

Jan 1, 1960

The purpose of this paper is to demonstrate how the Computational Fluid Dynamics (CFD) technique can be an attractive approach to evaluate the performance of face ventilation systems. To present the capability of the CFD for such a study and for design purposes, a series of simulations using CFD have been performed at the Department of Mining Engineering, University of Kentucky, for different face ventilation arrangements (e.g. different scrubber geometries, brattice (curtain) and continuous miners locations, airflow quantities, etc.). Results from these simulations are displayed as three dimensional graphs and discussed. Needs for the field validation of these results and refinements of design methodologies are also discussed.

Jan 1, 1998

By M. F. Corcoran

Rapid advances have been made in the past few years in the application of automatic controls and instrumentation to iron ore pelletizing plants. Present practice in applying instrumentation and control to the Grate-Kiln system of iron ore pelletizing is described. Major control points and loops are tabulated. Future trends in the application of digital control including computer data logging systems are described.

Jan 1, 1965

By Klaus Bauckhage

Phase-Doppler-anemometry (PDA)-measurements have to be taken from representative measuring positions from inside the spray cone, helping - with the support of simulated data of improved process models - to describe the multiphase flow situations within the spray cone - and accordingly to that - the heat transfer conditions for the rapid cooling and (partly) solidifying melt droplets before their impact onto the substratddeposit. Simulations and PDA-measurements thus give the base to confirm the hypothesis of the existence of a semisolid mixed-layer and it's influence on the resulting material structure during compaction. The dispersed particles in the spray cone exhibit a cooling and solidification process within a split of a second, which leads - as far as the particles solidify - to a dendritic structure with very short dendritic arm spacings. This causes within the particles extremely short distances for the following equalizing diffision processes taking place on a high temperature level (between liquidus and solidus) in the semisolid mixed-layer of the deposit and explaining the short residence times within this zone of only seconds up to a few minutes. This and the fact that the globular structure of the mushy zone (in the semisolid mixed-layer) leads to an unidirectional crystallization process over very short distances also explains the chemical and morphological ,homogeneity of the sprayed material. The dynamics of these process steps, the very special buffer function of the mixing layer during parameter variations as well as the controlled cooling process of the preform in order to avoid hot cracks influence the quality of the material. Due to the necessity of measuring and controlling the particle bound mass-, momentum- and enthalpy- fluxes to the deposit the PDA-technique has been adapted and modified in order to receive in-line and (in the future) also on-line data from the dynamics of the multiphase flow conditions within the spray chamber.

Jan 1, 1999

By Jue Kou, Lei Yu, Bern Klein, Lusheng Zhou, Chunbao Sun, Genzhuang Li, Reem Roufail, Amit Kumar

Magnetic liners can improve the performance of ball mills by increasing grinding efficiency, extending service life, and reducing maintenance costs. Despite their importance, the fundamental understanding and the quantitative investigation on the effects of the magnetic liners has not been addressed in the literature. This paper addresses this gap by studying charge motion, and how the use of a magnetic liner affects the breakage mechanism of the mill, using discrete element method (DEM) modeling and the Hertz-Mindlin contact model with relative velocity dependent (RVD) rolling friction. Charge motion was modeled under different mill speeds. Compared to conventional steel and rubber liners, the charge motion in the magnetic liner mill was predominantly cascading. Quantitative analysis of the energy dissipation within the mill was conducted to investigate mill breakage. Regardless of speed, over 50% of the total energy dissipation in the magnetic liner mill was in the form of abrasion and attrition. The results highlighted the appeal of magnetic liners in secondary and regrinding application, where abrasion and attrition are considered more efficient in the fine material breakage, and where impact is ideally minimized to reduce mill wear. A number of experiments were conducted to assess the effect of different model parameters on the performance of the magnetic liner mill. The highest abrasion/attrition intensity was observed with high values of the model parameters namely the restitution coefficient, static friction coefficient, and rolling friction coefficient.

By Robert M. Vadas

Special considerations are described as they apply to the design of ring gears for high-power grinding mills. AGMA requirements, the importance of the supporting structure, material selection and related field experience are discussed, with special emphasis on available and developing manufacturing technologies.

Jan 1, 1978

By C. G. Maier

The fundamental chemistry of zinc smelting, especially that part dealing with the chemical reduction of the zinc-oxide content of a roasted zinc ore, has been discussed by metallurgists in some detail, but, in the light of present knowledge, unsatisfactorily. A considerable portion of the information available has been qualitative, or quantitative in a sense that could not be interpreted chemically. A number of attempts to elucidate the physical chemistry of zinc oxide reduction have been based upon unsubstantiated and, as is now known, incorrect equilibrium data. To write upon the chemistry of zinc smelting at this time, when electrolytic methods for the production of zinc metal from ore are becoming increasingly widespread, may seem a belated effort. So, for example, C. A. Hansen,3 in the communicated discussion of an article by the author,4 writes as follows:

Jan 1, 1930