Search Documents

By Yuriy V. Gulyaev, Galina V. Sedelnikova, Valeriy D. Lunin, Valentin A. Chanturiya, Igor J. Bunin

"Probable mechanisms of disintegration of mineral particles in gold-containing sulphides and benefication products exposed to high-power electromagnetic pulses are discussed. Experimental data are presented to confirm the formation of breakdown channels and selective disintegration of mineral complexes as a result of pulse irradiation, which makes for efficient access of lixiviant solutions to precious metal grains and enhanced precious metal recovery into lixivia during leaching. Experiments with different gold-containing products revealed a synergetic effect of high-power electromagnetic pulses with widely varying parameters and moisture in mineral pores on breaking-up and gold extraction processes for various resistant goldcontaining mineral products.Several series of tests performed in IPKON RAS, IRE RAS and TsNIGRI yielded an absolute gain in precious metal recovery, up to 30-80 % for gold and 20-47 % for silver, with resultant gold recovery as high as 90 %. An essentially new, environmentally safe and energy-saving breaking-up technology has been developed for resistant gold-containing products. This new method would shorten the way from raw minerals to final products and help significantly reduce the cost of these products as it obviates the necessity for using the expensive procedures of energy-intensive and environmentally hazardous oxidative roasting and autoclave breaking-up for ore concentrates."

Jan 1, 2003

By A Takahashi, Y Uchisawa, M Hayashi, T Watanabe, M Susa

Owing to the deterioration of iron ore, the Al2O3 concentration in iron ore increases, and thus it is important to investigate the effect of increment in Al2O3 concentration on the microstructures of iron ore sinters. During the sintering process, a melt is present in the sinter for only a few minutes, and therefore the microstructure of the sinter doesn’t reach thermodynamic equilibrium. Nevertheless, the formation process of the microstructures can be interpreted and predicted to some extent from the equilibrium phase diagram. This study investigated the liquidus isotherm in the CaO-SiO2-Fe2O3- 5 mass% Al2O3 system at 1240°C in air and the phase equilibria of silico-ferrite of calcium and aluminium (denoted by SFCA) and SFCA-I by XRD (X-ray diffraction analysis) and electron probe micro analyzer (EPMA). The following results were obtained: 1. The ferrite melt region with a high Fe2O3 concentration shifts to the lower Fe2O3 side than the liquidus isotherm in the CaO-SiO2-Fe2O3 system. 2. The compositional region of SFCA extends in the CaOꞏ3Fe2O3-4CaOꞏ3SiO2 direction than the silico-ferrite of calcium (denoted by SFC) composition region with a 0 mass% Al2O3. 3. SFCA-I is observed in the present system, which suggests that the increment in the Al2O3 concentration contributes to the stability of SFCA-I. These results imply that an increment in Al2O3 concentration in iron ore leads to a decrement in the volume fraction of the bonding phase and that the fraction of the SFCA phase increases, and those of 2CaOꞏSiO2 and slag phases decrease in the bonging phase. The SFCA-I phase is also precipitated from the slag with an Al2O3 concentration around 5 mass%.

Jun 19, 2024

By Jorge Luiz Soares do Couto

O presente trabalho tem como objetivo realizar uma análise comparativa do comportamento de quatro metais de solda obtidos pelo processo arame tubular de forma a avaliar o efeito da relação Ni-Mn nas propriedades mecânicas. Foram soldadas juntas multipasse, com consumíveis da classe 110ksi de resistência mecânica, preaquecimento de 200°C, corrente contínua e posição plana e aporte térmico nominal de 1,2 kJ/mm. Após a soldagem, realizaram-se ensaios mecânicos e metalográficos em corpos-de-prova retirados integralmente do metal depositado, na condição de como soldado e após tratamento térmico pós-soldagem. Os resultados mostraram que as melhores propriedades mecânicas foram obtidas para uma composição contendo 1,35%Mn e 2,50%Ni. Adicionalmente, verificou-se que o tratamento térmico pós-soldagem propiciou uma redução da tenacidade ao impacto dos metais de solda de maior resistência devido à precipitação de carbetos nos contornos de grão.

Aug 7, 2018

By Sumit Kumar Hota, Asadi Srinivasa Reddy, Ashok Kumar, Ashish Agrawal, Surajit Sinha, Chandra Sekhar, Tanay Ray

In the current operational facility, due to the absence of pellet pot facility, a novel technique is developed wherein the pellets with different chemistries prepared in the laboratory are fired in an induration machine by placing them inside the Inconel baskets. In the present work, an attempt is made to optimize the pellet chemistry by developing 2 different flux pellets, viz., low basicity (B2: CaO/ SiO2 = 0.3) pellets and high basicity (B2 = 0.9) pellets, and further the effects of basicity on pellet properties, viz., cold compressive strength, porosity, swelling index, reducibility index, and softening and melting temperature, are studied. It has been found through the multiple operational trials that increasing the basicity of pellets from 0.3 to 0.9 results into improving the pellet strength, reducibility and softening and melting characteristics. Moreover, it is observed that the swelling index of pellets is reduced by adding 2% MgO to both low and high basicity pellets that could be attributed to the formation of high melting point slag in pellets. The operational trial has resulted into producing pellets that exhibit a combination of desired mechanical strength, improved swelling, and reducibility index and possess better softening–melting behavior among all the chemistries studied.

May 24, 2022

By R. F. Abernethy

A chemical method of determining microgram quantities of arsenic in coal was investigated by the Bureau of Mines to supplement a semiquantitative spectrographic method of determining arsenic in coal ash. In accordance with a method recommended by the International Organization for Standardization, 1-gram samples of coal are decomposed by wet oxidation with boiling sulfuric acid (H2S04) and nitric acid (HN03) to remove the organic matter. After heating to fumes of SO3 to remove HN03, the arsenic is separated as arsine by the action of zinc in H2S04 solution. The arsine is absorbed in dilute iodine solution in which the arsenic is determined colorimetrically by the molybdenum-blue reaction. Two modifications of the method for obtaining the arsenic in solution, in addition to the wet oxidation method, give satisfactory results. The modifications are (1) furnace ashing with MgO added to the coal, followed by treatment with H2S04, and (2) extraction of arsenic from the coal by dilute HNO3 without ashing. Float-and sink-tests show that arsenic is associated mainly with mineral matter in the three coals examined. High-temperature ashing tests show that very little arsenic is volatilized from coal ash below 1,000° C, but it is virtually all removed from the ash at 1,300° C.

Jan 1, 1968

By E. F. Steeb, P. C. Rosenthal

BlANKS 8 in. long were cut from the as-received bar stock and austenitized at 1560° F for 1 hr, oil quenched, tempered at 1140°F for 1 hr, and water quenched. The heat-treated blanks were machined into tensile specimens which were subsequently used for the straining operation. Some of the tensile specimens were temper embrittled at 900°F for 24 hr and air cooled prior to or following the straining operation. The specimens were strained in tension up to 5 pct total strain (elastic plus plastic) either at room temperature or at 900°F. The reduced sec- tion of the tensile specimen employed was 5 in. long and 0.600 in. in diam. This size specimen was sufficiently large to permit two standard Charpy impact bars to be machined from it. One group of specimens was temper embrittled at 900°F for 24 hr under stress of about 20,000 psi applied with a hydraulic tensile testing machine. Approximately 0.34 pct plastic strain occurred during this treatment. A comparison of series "A" and "B" data in Table I at 0 pct strain, reveals that the steel was rather highly susceptible to temper embrittlement, the embrittling treatment causing the transition temperature to rise 165°F. The 28 ft-lb level, which was near the center of the sharp-rising portion of the transition curve, was selected as the

Jan 1, 1959

By C. L. Dake

AN insistent and steadily growing demand is evident for the broadening of undergraduate curricula in engineering. Among suggested additions are training in public speaking, report writing, business law and contracts, accounting, finance, money and banking, scientific management, economics, social and labor problems, psychology, and ethics. The demand for these subjects comes from the older engineers and from the industries that employ our graduates. Of course, many of the men who suggest such changes are influenced largely by their personal needs and contacts, but the demand is sufficiently widespread to merit serious study by educators. In fact, many educators themselves concur in the proposals for broader training. These matters were examined intensively a few years ago in an exhaustive study of engineering education. Opinion at that time was rather strongly against any profound change. Since then, however, the whole economic system has undergone violent disruption. Even if recommendations made a few years ago were appropriate to the conditions then- obtaining, the enormously changed conditions of the present make advisable a further careful study of this problem. In recent years, mergers, to reduce costs, have sharply limited the number of engineers employed and have thereby intensified the struggle to secure positions. In this stiffer competition, engineers with the most adequate training undoubtedly fare the best.

Jan 1, 1934

By J. S. Webb

This is one of a series of papers dealing with mining methods, practice, and costs be¬ing published by the United States Bureau of Mires. In this paper a description of the mining practice in vogue at the Braden unit of the Kennecott Copper Corporation is undertaken. PRODUCTION At present (1931) the entire production of ore is being obtained from the Teniente mine. The miring method in use is an adaptation of block undercutting which has been a development of the stoping and pillar caving experience obtained at this property. Improvements in mining practice are constantly being made.

Jan 1, 1932

By Janet Torma-Krajewski

Research has shown that an ergonomics process that identifies risk factors, devises solutions to reduce musculoskeletal disorders (MSDs), and evaluates the effectiveness of the solutions can lower worker exposure to risk factors and MSDs and improve productivity. A review of the Mine Safety and Health Administration (MSHA) injury/illness database indicated that 46% of illnesses in 2004 were associated with repetitive trauma and 35% of nonfatal lost days involved material handling during 2001? 2004. Even though these statistics show that MSDs significantly contribute to occupational illnesses and injuries in the U.S. mining industry, few mining companies have implemented an ergonomics process. Despite the many unique challenges in the mining environment, three mining companies partnered with the MSD Prevention Team at the National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory to demonstrate that an ergonomics process could be systematically implemented and effectively integrated with existing safety and health programs. Because these three mining companies were very different in organization, culture, and size, the ergonomics processes had to be modified to meet the needs of each company. A description of how these three companies applied ergonomics and the tools and training used to implement their processes is given. Prior to discussing the case studies, general information on the elements of an ergonomics process is provided.

Feb 1, 2009

By T. R. A. Davey

A Survey of current and recent research and developmental work is supplemented by predictions for processes which should be developed over the reminder of this century.

Jan 1, 1970

By Christopher W. Schram, Allan B. Tanner, Frank E. Senftle, George R. Boynton, Philip W. Philbin

A borehole sonde using a 252Cf neutron source and a Ge(Li) gamma-ray detector was field tested in a coal bed in Belmont County, Ohio, to ascertain whether such a device could be useful as a coal-exploration tool. As the sonde was lowered into the borehole, successive spectra were accumulated over short time intervals. The intensities of the capture gamma rays from hydrogen and of decay gamma rays from aluminum were determined simultaneously in each spectrum. A log of the intensities versus depth shows the depth and thickness of the coal bed. With the sonde stationary at points above, in, and below the coal bed, capture gamma rays were measured to show the variation in concentration of certain elements. From the spectrum recorded in the bed, a complete ultimate analysis, the percent ash content, and the heat content were determined without recourse to an external standard. Delayed gamma-ray analyses of the core were also made on the surface in the vicinity of the borehole in a fixed-geometry irradiation facility wing the detector in the borehole sonde. The concentrations of 10 elements were determined by this method on a coal split from the drill core. These experiments show that it is feasible to use a 252Cf- Ge(Li) borehole sonde as an aid in coal exploration.

Jan 1, 1979

By D. K. Crampton

THE object of this work was to obtain and correlate information on effect of internal stress in variously drawn tubes on several properties. Also, a simple approximate method of comparing types of stress distribution in such variously drawn tubes was sought. There is also included some work on comparison of single and polycrystalline materials and effect of different types of operation and preferred orientation. PREPARATION OF MATERIAL A series of tubes was drawn to study the effect of the type and degree of final reduction on various physical properties and the approximate distribution of stress intensity across the tube wall. The material used all came from a single heat of 70-30 brass melted in a regular production Ajax-Wyatt induction furnace. The analysis of the metal as cast was: copper, 70.36 per cent; lead, 0.04; iron, 0.02; zinc, balance. The material was cast in "shells" with 4 in. outside diameter and 3/4 in. wall thickness. It was drawn part way down according to the usual standard mill schedule and then by suitable individual schedules to finish by a variety of types and degrees of drawing to the same final cases in every instance; namely, 0.750 in. outside diameter by 0.080 in. wall thickness. The exact final draws, together with the percentage area reductions, diameter reductions and gage reductions are given in Table 1.

Jan 1, 1932

By de Vaux. Deryck, Natalie J. Shackleton, Vratislav Malysiak Cyril T. O. Connor

"The major losses of PGM and base metals in the beneficiation of platinum group deposits occur during the separation of gangue from the value minerals by selective flotation. A number of studies have shown that this negative impact on flotation is due to surface passivation, caused by various ions that may originate from the external water supply or, as is likely in the majority of cases, from the oxidation of the mineral surfaces and the grinding media. This investigation aimed at reducing surface passivation of pentlandite and inadvertent activation of pyroxene, thereby improving ultimate valuable mineral recovery and selectivity. Both synthetic minerals and plant ores were studied in order to determine the effect surface passivation and inadvertent activation have on mineral surface alteration and floatability. Zeta potential determinations, microflotation, ToF-SIMS (Time of Flight Secondary Ion Mass Spectrometry) analyses, laboratory batch flotation tests and continuous flotation testwork were used as tools to study the surface alteration and/or floatability.Zeta potential determinations and ToF-SIMS analyses showed that copper adsorption is non-selective. Both pentlandite and pyroxene become copper (II)-activated in the presence of copper sulphate and subsequently, in the presence of xanthate, adsorption of the collector will occur onto copper activated mineral surfaces. Zeta potential determinations also showed an alteration of the surface charge in the presence of polyphosphate, thereby inhibiting surface passivation of sulphides by slime coatings due to surface repulsion.The addition of diethylenetriamine (DETA) reduces the copper concentration on both minerals, predominantly on the pyroxene surfaces and polyphosphate further enhances the selectivity at pH 6.The microflotation and batch flotation data obtained has shown a significant improvement in the ultimate flotation response of valuable mineral recovery and concentrate grade compared to the standard reagent regime, while the continuous flotation results significantly improved the selectivity, however, at a similar ultimate recovery."

Jan 1, 2003

By P. T. Gallagher, W. A. Oates

THE partial excess entropy of interstitial solutes in metals, SXS , has usually been interpreted as being principally vibrational ever since the initial statistical treatment of hydrogen in metals by Fowler and Smith-ells. The vibrational entropy is considered being due to the optical modes of the light interstitial atom. Little attention has been given to the magnitudes of the values of SXS'. Leiser and Witte2 and Ebisuzaki and O'Keeffe3 have noted that for hydrogen in metals Si is approximately constant for different metals. On the other hand if it is assumed that the interstitial solute is an isotopic defect then, as shown by McLellan, SXS should vary from metal to metal as follows: where S is the standard entropy of the solvent and Mi, M, are the masses of the interstitial and solvent atoms. respectively. Fair agreement with this equation was found for oxygen in silver and nitrogen in iron4 and for carbon in iron.= Ln a subsequent analysis of metal- hdrogen systems McLellan' found a variation of $' from metal to metal but not in a manner expected from the isotopic impurity equation. However, a possible correlation between the energy of solution, Ei, and sf was noted. Similar correlations have been noted for certain dilute substitutional solid Solutions 7, 8 and recently Kubaschewski 9 has demonstrated a correlation between integral heats and ex-

Jan 1, 1970

By Philip C. Tully

These modifications to the Redlich-Kwong equations for pure hydrogen and neon were developed after an unsuccessful attempt to generalize a modification technique previously developed for helium. New coefficients of the B terms were developed by minimizing the residuals. No changes were made in the coefficients of the A terms. For normal hydrogen, B was changed to [0.08063Tc PcT] for temperatures from 980 to 423° K and pressures up to 1,050 atm. The average deviation in Z was 0.36 percent with maximum deviations less than 1 percent for all but a few low-temperature points. For neon, B was changed to [PCT 0.1025T], for temperatures from 120° to 973° K and pressures up to 1,500 atm. The average deviation in Z was 0.34 percent with maximum deviations less than 1 percent for all but a few high-pressure and low-temperature points. Efforts to attain a lower temperature range to comparable accuracy with this type of modification were unsuccessful. In the range of applicability, these equations should be used with caution when calculating derived thermodynamic functions, such as the isobaric specific heat.

Jan 1, 1968

By W. E. Bruce, James Paone

Drillability or a measure of drilling performance has been based on ( 1 ) hardness and toughness of rocks , ( 2 ) power input to the drill compared with total volume of hole , and ( 3 ) penetration related to resistive forces of rock on the applied penetrative forces . An analysis of some representative previous work is made . Experimental drillability curves from AX- size diamond core bit performance in eight different rocks ranging from dense hard taconite to soft limestones are presented . Results show that in small bore diamond drilling , compressive strength and possibly other rock properties may be a useful parameter in predicting drilling rates .

Jan 1, 1963

By G. Roberts, S. S. Klima, W. R. Reed, J. Deluzio, G. Ross, A. Mazzella

The abstract discusses the problem of silicosis among roof bolter operators in coal mines due to respirable quartz dust (RCS) exposure. It presents a study comparing a new wet box collection system to the traditional dry box system. The wet box system uses water to saturate collected material, reducing RCS exposure during cleaning. The study found that the wet box system significantly reduced RCS exposures and quartz content in samples compared to the dry box system.

May 11, 2022

By James P. Ludwig

This report provides the results of a two year study of the projected time and cost requirements for new mine development in Wisconsin and is based on a unique blend of information from mining company officials, state regulatory agency officials and contractor experience. Through formal cooperative and review agreements with Kennecott Copy per Corporation, Exxon Minerals Co., U.S.A. and Noranda Mines Ltd., and the Wisconsin Department of Natural Resources plus informal arrangements with knowledgeable Wisconsin persons, lists of the tasks and subtasks required to plan a new mine in Wisconsin were developed. Times and costs were assigned to all tasks and subtasks and these data reviewed by all cooperators. Critical Path Method Diagrams were then developed for a generalized mining project. Total time and cost for the premine planning process was estimated to be 25..1 years and 223 person-years of professional time excluding public affairs effort respectively. By eliminating redundancies in the process and by increasing project efficiency through early public review and participation, recom¬mendations were made to lessen the time and lower the cost of premine planning. The streamlining recommendations could shorten the overall critical path length to 18.16 years and lower the cost to 208 person-years of professional time excluding public affairs effort. The estimated distribution of professional effort (cost) for mine planning in Wisconsin approximates 50.5% for traditional mine engineering tasks, 36.6% for environmental-regulatory tasks and 12.9% for traditional geological-exploration tasks.

Jan 1, 1979

By Oliver Bowles

The term" sandstone" is applied to a rock composed of mineral grains smaller than pebbles, cemented together more or less firmly. "Conglomerate" is the name given to a rock composed of pebbles, or pebbles and bowlders, of various sizes cemented together. If the pebbles are large and well rounded the rock is sometimes called " pudding stone." Although the term "sandstone" includes all varieties, certain specific terms are applied to types characterized by particular compositions, colors, or uses. "Quartzite" is a variety in which the individual grains are so firmly cemented together with quartz that the rock will fracture as easily through the grains as through the cement; "ferruginous sandstone" is one rich in iron as cementing material, or as grains, or both; "micaceous sandstone" is one in which mica is prominent; " arkose" is a feldspathic or granitic sandstone composed of angular grains; "calcareous sandstone" is one containing considerable calcium carbonate; and" argillaceous sandstone" is one containing considerable clay. The term "flagstone" is used for a rock that splits readily into sheets suitable for flagging; "freestone" for rock than can be cut or carved readily, and with equal ease in all directions; and" ganistel'," in the United States, for sandstone suitable for the manufacture of refractories. Others are named from their characteristic colors such as " bluestone," " redstone," or " brownstone."

Jan 1, 1917

By Christoph Pichler

A special desulphurization slag accrues during the processing of iron ore to steel, which is needed to generate high quality steel. Sulphur removing is done by different technologies, but the most common one is the generation of a high sulphur containing slag by sulphur affine elements. Currently, this desulphurization slag is partly recycled, however, huge amounts are still dumped. To utilize this desulphurization slag for future purposes, a recycling process must be established. Therefore, first characterization of this material started some years ago at the Chair of Nonferrous Metallurgy, Montanuniversität Leoben. Subsequent trials in lab scale size were performed, also some investigations for different treatment steps were evaluated, starting with a parameter study in a hot stage microscope at various gas-atmospheres. Finally, the developed recycling process concept was verified in pilot scale trials to confirm the new recycling technology. Due to the successful treatment process, also a patent was applied.