Search Documents

By S. Mohanta, I. D. Behera, B. Sahoo

"Run-of-mine coal contains particles of different sizes with different specific gravities, and when this coal is crushed, the amount of material present in a particular density class changes. This alters the washability characteristics of the coal, which affects the quantity, quality, and separation efficiency of the gravity-based coal washing process. The degree of difficulty in washing a typical coal at a particular specific gravity depends mostly on the amount of material occurring within ±0.1 specific gravity range, which is known as ‘near-gravity material’ at that particular specific gravity of separation. In this paper, two numerical indices, namely ‘near-gravity material index’ and ‘index of washability’, are used to quantify the distribution of near-gravity material in different density classes and to evaluate the degree of difficulty involved in the washing process. The results of this preliminary investigation indicate the uniform distribution of near-gravity material in all density classes for finer size fractions, whereas for coarser size fractions more near-gravity material is present in the lower density classes, making the washing process more difficult at a lower specific gravity of separation. IntroductionThe prime objective of coal beneficiation is to remove physical impurities as effectively and economically as possible. The beneficiation process includes various operations on the asmined coal to make it more suitable for enduse application without destroying the physical identity of the coal. There are several coal beneficiation processes, but gravity-based separators remain the most efficient unit operation for removing the undesirable gangue material from run-of-mine coal. These separators exploit the difference in density between coal particles and gangue particles to effect a separation. The feed is introduced into an aqueous suspension of ultrafine magnetite with a particular density. The feed particles with a relative density less than that of the suspension (clean coal) float to the top surface of the suspension, whereas particles denser than the suspension density (gangue material) sink to the bottom. When the difference in density between the particle and the aqueous suspension is large, the separation is easy, but when this difference is less the separation becomes much more difficult since the settling velocity of the particles is very low. This lower settling velocity increases the probability that particles that should report to floats report to sinks, and vice versa, hence increasing the amount of misplaced material. Therefore, the degree of difficulty in beneficiating a typical coal at a particular specific gravity depends on the amount of material occurring within ±0.1 specific gravity range. This is known as ‘neargravity’ material, also termed ‘near-dense’ material, at that particular specific gravity of separation."

Jan 1, 2016

By AIME AIME

COAL occupied a large place in the technical sessions of the Institute at its annual meeting for in addition to three sessions specifically de- voted to coal the two sessions on mine ventilation and the two on ground movement and subsidence, which are reported under their own headings, were primarily concerned with coal. The first session on coal was a joint one with the Iron and Steel Division, on Wednesday afternoon, with F. H. Crockard and J. R. Campbell presiding as joint chairmen and the latter actually officiating. The principal topic of discussion was G. S. Scott's paper "Evaluation of Coal for the Making of Blast- Furnace Coke," which has been published as T. P. 159. The author made a brief statement of its con- tents to start the discussion and the chairman, after briefly reviewing it himself, called on C. A. Meissner to start the discussion. He briefly reviewed the economic factors in the use of coal for coke-making, saying that not only .does the removal of 1 per cent of ash from the coal reduce the cost of pig iron 12 or 13c. per ton, but it also permits coke of satisfactory structures to be made from a coal which otherwise could not be used. He stressed the importance of uniformity in blast-furnace fuel and discussed the benefit of mixing different coals as raw material for the coke oven and cited experience with Illinois coals.

Jan 1, 1929

By Travis Coleman, Elvis Ishimwe

Currently, more than 400 drilled shafts have been constructed by various contractors at the I-90/94 and I-290 Jane Byrne (Circle) Interchange, located near downtown Chicago, Illinois. Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) tests were performed to evaluate the integrity and concrete quality of the drilled shafts installed at this project. For Phase I of the project the shafts were tested using CSL methods, and the shaft integrity was identified by analyzing the First Arrival Time (FAT) and the signal strength (energy) measurements. For the major portion of Phase II, the Illinois Department of Transportation (IDOT) accepted TIP testing as a substitute for CSL at the request of the contractors. The CSL testing results indicated 54 percent of the tested shafts had anomalies, and 78 percent of these anomalies were located within the lower three diameters of the shafts. To date, TIP testing results indicated the shaft integrity was as expected and acceptable for the all 34 tested shafts. A review of the testing results and a discussion of the detected anomalies are presented. In addition, a comparison of both TIP and CSL measurements is presented in this paper.

By Vijayakumar Viramuthu, Martin Heinrich

Tower of Lot L, L1 & M, Kuala Lumpur City Centre when completed would stand 700 m tall. This Mega tall Skyscraper would merely be less than 500 m away from the world tallest Twin Tower, the Petronas Twin Tower. From June 2018 to February 2020 BAUER (MALAYSIA) SDN. BHD. constructed 225 nos bored piles with diameters of 2.0 m and 2.5 m for this tower. To comply with the depth requirement of the initial design and the need to have the pile toe 2.0 m above competent bedrock, the drilling equipment was required to be able to achieve a maximum drilling depth of 150 m. Actual piles constructed on site were deeper than 120 m. These dimensions caused superlative challenges which included but were not limited to controlling the open borehole stability over time with polymer, installing 70 t heavy steel cages and pouring up to 550 m³ concrete continuously in conjunction with installation of 88 t heavy kingposts into workable fresh concrete. The piling works were executed with one BAUER BG 48 and one BG 72, the biggest drilling rig globally available.

May 1, 2022

By Arthur L. Christenson, Clarence E. Jackson

IN the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition1 may be corrected to the grain size observed in an actual weld,2 or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.3 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2100°F. has been used. In studies of the end-quench hardenability specimen quenched from 2100°F. instead of from a lower temperature of 1700°F., it is important to ascertain the relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6,7 French has considered this effect from both theoretical and experimental aspects. In French's studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been proposed: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching. temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1943

By J. Appleby

This paper reviews earlier in-plant testing at the Sidbec-Normines pelletizing plant at Port Cartier, Quebec, Canada. It describes the result of the more prolonged use of coke breeze during recent months and in addition, the effects of varying dolomite and coke additives upon the metallurgical properties of the pellet production have been studied. Mention is also made of some brief test work carried out to use peat moss as a carbonaceous additive to the pelletizing process and in particular the plans for future work in this respect. Earlier laboratory pot-grate test work had indicated that a production rate increase of between fifteen and twenty percent was a practical possibility, or alternatively that the plant could be run at design rating with significantly lower energy consumption. These energy reductions were of the order of ten to fifteen percent for fuel and main process fan power respectively. The physical and metallurgical pellet properties for both blast furnace and direct reduction furnace use were little affected by the production rate increases, and were actually somewhat improved when practicing maximum energy conservations. Pellet properties could be further improved by not extracting the maximum energy economy. Two phases of carefully controlled in-plant testing were run to assess the effect of energy conservation under plant conditions. These two phases of testing confirmed that an overall fuel saving of approximately fifteen percent could be realized, with a reduction in the Bunker C oil consumption of about forty-five percent, and a reduction in main process fan power of approximately ten to fifteen percent. The present scope of work is aimed at establishing the use of varying levels of coke addition up to about one percent under normal plant operating conditions.

Jan 1, 1980

By R. S. Busk

TWO groups of binary alloys were prepared. The first group consisted of those elements relatively soluble in magnesium: Li, Al, Zn, Ga, Ag, Cd, In, Sn, Hg, T1, Pb, and Bi. These are predominately Group B elements. The second group consisted of most of the remaining metallic elements, all of which are relatively insoluble in magnesium: As, Au, Ba, Ca, Ce, Cu, Ir, La, Mn, Ni, Pd, Pt, Rh, Sb, Si, Te, Ti, W, and Zr. These are all Group A, transition, or rare earth elements. Alloys of the first group were prepared by melting sublimed magnesium and elements as pure as obtainable in a graphite crucible, using a standard flux1 for protection. The melts were poured into a small graphite mold to produce 3xY4 in. diam slugs. Spectroscopic analyses were made of each slug. In all cases, the total impurity content was less than 0.05 pct. The slugs were then heat treated 5°C below the eutectic temperature until complete solution, as judged metallographically, was obtained. Filings from the center of the slugs were compacted at room temperature into 1/2 in. long x 1/4 in. diam cylinders, sealed in pyrex under 1/2 atm of purified argon, annealed at the heat-treating temperature for 1 hr, and quenched in water. After the X-ray diffraction patterns were made, each compact was analyzed chemically for the solute. It was found that the Mg-Li alloys reacted during filing to reduce the Li in solid solution. For this series of alloys, the slug was cold worked, annealed in purified argon, the surface dissolved in dilute HC1 to a depth of about 0.005 in., and the X-ray exposure made on the fresh surface. This procedure resulted in sharp, continuous lines and in true values for the lattice parameters. The alloys in the second group were prepared in the same way except that about 1 wt pct of each solute was added. Since the solubility limit was exceeded, not all the solute dissolved. These alloys were analyzed spectroscopically only to confirm the presence of the solute. The diffraction patterns were of the back-reflec-tion type using the characteristic copper radiation* and a flat cassette. Both the film and the specimen were rotated. The specimen temperature was maintained at 25" ± 1°C. The films had sharp lines; their diameters were measured directly to 0.01 cm. The parameters were calculated from the line diameters using a modified version of Cohen's extrapolation method.2 his method effectively eliminates systematic errors such as film shrinkage, inaccurate alignment, and non-precise film-to-speci-men distance. The random errors were minimized

Jan 1, 1951

By Arthur L. Christenson, Clarence E. Jackson

In the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition* may be corrected to the grain size observed in an actual weld? or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.8 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2Ioo°F. has been used. In studies of the end-quench hardenability specimen quenched from 2Ioo°F. instead of from a lower temperature of I7OO°F., it is impor-TaiiT to ascertain The relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6'7 French has considered this effect from both theoretical and experimental aspects. In French's studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been propped: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1944

By Harlan W. Nelson, James B. Purdy

The great majority of stokers used in residential heating installations are of the clinkering type. Because of inherent characteristics of the underfeed combustion process as it occurs in these small stokers, and because of the wide range of operating conditions encountered in residential heating schedules, not all bituminous coals can be used successfully in residential underfeed units. The problem of providing consumer satisfaction has been attacked by the joint efforts of the stoker manufacturers and the coal industry; the stoker manufacturers have been concerned with improving their product to permit the use of a wider range of coals, and coal operators have made every effort to market selected and better prepared coals. In view of the wide range of physical characteristics and chemical properties of bituminous coals, the problems are real and are receiving increased attention. Some twelve years ago a laboratory method was developed at Battelle Memorial Institute for the relative evaluation of coals for use in residential underfeed stokers. The method was developed in conjunction with work being done at that time for Bituminous Coal Research, Inc., and for individual coal producers, to obtain information on the characteristics of coal that determined the successful performance of the small stoker. Details of the equipment and test procedure were given by R. A. Sherman1 in a paper presented at the University of Illinois Fifth Short Course in Coal Utilization. During the past several years, the evaluation of over forty different coals has been determined by investigations sponsored at Battelle by coal operators in the eastern producing districts. The purpose of this paper is to compare the results and conclusions derived from the various tests with marketing experiences of the operators, and to discuss briefly the relationship of test results to standard laboratory determinations. Equipment Used in Tests Fig 1 shows schematically the equipment used in the evaluation tests. The stoker is a commercial model of conventional design, having a nominal feed rate of 30 Ib per hr. A special laboratory furnace is used, which is tightly sealed to prevent the entrance of secondary air. The complete stoker-furnace assembly is mounted on platform scales which permits the measurement of combustible weight losses occurring during the test. The furnace stack, in which are a thermocouple, flue-gas sampling tube, and smoke meter, is connected to the laboratory exhaust breeching through a friction-less connection. Through use of an auxiliary blower system, provision is made for the measurement of the air delivered by the stoker fan to the windbox. A water seal in the duct work eliminates inter-

Jan 1, 1950

By Arthur L. Christenson, Clarence E. Jackson

In the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition* may be corrected to the grain size observed in an actual weld? or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.8 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2Ioo°F. has been used. In studies of the end-quench hardenability specimen quenched from 2Ioo°F. instead of from a lower temperature of I7OO°F., it is impor-TaiiT to ascertain The relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6'7 French has considered this effect from both theoretical and experimental aspects. In French's studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been propped: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1944

By John Wilson

"The Rietveld numerical method was used to calculate the relative abundances of phases in both synthetic binary mixtures and synthetic and natural ores, using X-ray diffraction data. The results were compared with those of image analysis and a chemical method. The ranges of the relative errors were estimated. The Rietveld method is found to be acceptable for determining the abundances of major and minor phases and the amorphous component of partially crystalline samples. In complex mixtures, where there are several trace phases (~<2 wt%) present, the technique becomes less accurate. It is most useful as an alternative technique to image analysis when sample preparation is problematic or sample particle sizes are sub-micron. It is a manual method which requires user input during the fitting process, but is both simpler and faster than image analysis due to the reduced set up time and sample preparation required. It is now implemented at CANMET as a technique for quantitative analysis.INTRODUCTIONUntil recently, the Applied Mineralogy group at CANMET used only image analysis and chemical techniques to determine phase quantities. An effort to develop quantitative X-ray diffraction (XRD) has been on-going for several years. Initially, the reference intensity ratio (RIR) method with external standards was tried with some success (Szymanski and Petruk, 1989). The main difficulty with this technique was finding adequate standard material for each phase present in the sample. This shortcoming made the method ultimately impractical, given the wide variety of materials which come to the laboratory for analysis.The Rietveld refinement method of quantitative XRD (Hill et al 1993, Mumme et al 1996), in contrast, requires no standards and requires minimal sample preparation and therefore a more rapid turnaround compared to image analysis. The Rietveld method also has advantages over image analysis in that it can identify and quantify polymorphs, ultra fine materials and many types of hydroxide products. As well, it is useful for analyzing materials such as bauxite or talc, which do not polish well enough for making mounts of the quality required for image analysis. To quantify amorphous material and phases which are present in amounts below the detection limit of XRD, the addition of a standard material is still required. However, in such cases only one standard is needed, which is alumina."

Jan 1, 2003

By Sean Hillacre, Arthur Lieu

NexGen’s approach to uranium processing design including the crushing/grinding and leaching of raw ore through to yellowcake precipitation and tailings management focuses on minimizing surface footprint, freshwater consumption, and human radiation exposure. Applying the concept of best available technologies economically achievable (“BATEA”), NexGen continues to research, evaluate, test and validate various advanced technologies that can be incorporated into the Project design, including distinctive tailings storage techniques. Additionally, NexGen is proposing that tailings generated from the mill processes be used as cemented paste backfill of stopes, as well as stored in a purpose-built, Underground Tailings Management Facility (“UGTMF”) comprised of several dedicated chambers. The paste backfill method of tailings storage is used globally, however, constructing purpose-built tailings chambers in waste rock is a new concept in uranium mining, which would typically be cost prohibitive for most projects given the expense to develop non-economic material for the sole purpose of storing tailings. The Rook I Project is uniquely positioned to implement the UGTMF due to robust Project economics and favourable technical setting which provides NexGen with the opportunity to set an elite standard for tailings management. When compared to conventional surface tailings management facilities, storing tailings underground as cemented paste reduces geotechnical, geochemical, environmental, and human health risks associated with tailings management. Additionally, the UGTMF vastly reduces the area of surface disturbance and allows for progressive decommissioning during the life of mine operations.

Jan 1, 2020

By Roy J. Helfinstine, Gilbert H. Cady

One of the most urgent needs in the field of coal combustion is the ability to predict the performance of a coal from knowledge gained from small-scale tests. Numerous types of analyses and tests are conducted on coal, including the proximate and ultimate analyses, heating value, varieties of sulphur, ash analysis, ash fusion temperatures, free swelling index, petrographic analysis, and Gieseler. plasticity. The Illinois Geological Survey has made an intensive study of the value of these tests for judging the performance characteristics of the coal as actually utilized. To date, three reports1,2,3 have been issued, and another is being prepared. The present paper briefly summarizes some of the results found in the studies. Equipment The equipment used for the tests is described in some detail in the above mentioned publications. Briefly, it consisted of a domestic stoker, cast-iron boiler, and water-cooled heat exchanger, which were operated as a forced circulation hot-water system. The entire unit was mounted on scales. Instruments for recording the per- formance of the coal included a hot-water meter to indicate the quantity of water flowing through the boiler; a two-pen, mercury-actuated thermometer to record the temperatures of the water entering and leaving the boiler; a chemical-type meter to record the percentage of CO2 in the stack gases; a pressure gauge to record the static pressure in the stoker-air duct; and a multipoint potentiometer to record the temperatures in the stack and room, and the opacity of the stack gases. A 16 mm motion picture camera was available for taking pictures of either the fuel bed or the scale dial. Procedure The tests described in this report can be conveniently divided into three phases. For the first phase, a load of 5 or 6 tons of unwashed coal (usually screenings) was obtained from each of fourteen Illinois mines. These coals were all crushed and screened to a size of 35 in. (square hole) by 8 mesh. Combustion tests were made on a part of this raw, screened coal. Another portion was passed over a concentrating table to reduce the ash to what was considered to be commercially reasonable, and combustion tests were made on this upgraded coal. The ash content of the remaining coal was reduced to a still lower figure by passing it over the washing table with greater reject, or by standard float-sink procedure. This cleaned fraction was then tested in the stoker-boiler unit. Thus three coals with varying ash content were tested from each mine. For the second phase reported here, coals were obtained from four Arkansas mines and tested as received and after passing over the concentrating table with a normal reject. One Illinois coal was tested in the "washed" condition only. The third phase included tests on commercially prepared stoker coals

Jan 1, 1950

By H. C. Stumpf, L. A. Willey, V. L. Fink

Very few studies of the aluminum-sodium system have been reported. Heycock and Neville1 were unable to detect any solubility of sodium in liquid aluminum. Mathewson2 prepared an equilibrium diagram consisting of two horizontal lines at the melting points of the two metals. He was unable to detect solubility at either end of the system. Scheuer3 first developed a method for the chemical determination of sodium in aluminum and then studied the solubility of sodium in liquid aluminum. His method involved heating aluminum with excess sodium under hydrogen until the two liquids were at equilibrium, chilling the melt, and analyzing the aluminum-rich layer. He reported the solubility to be 0.10 pct sodium at 700°C, 0.115 pct at 750°C, and 0.128 pct at 800°C. This paper on the aluminum-sodium system is the twenty-first in a series from the Aluminum Research Laboratories describing equilibrium relations in aluminum alloy systems. Materials The alloys for this investigation were prepared from electrolytically refined aluminum (99.99 pct) and sodium of reagent quality conforming to specifications of the American Chemical Society. Chemical analysis of the aluminum showed the fol- lowing impurities: 0.002 pct Si, 0.002 pct Fe, 0.002 pct Cu, <0.001 pct Mn, 0.002 pct Mg and 0.001 pct Na. The sodium content of all alloys was determined by either chemical or spectro-graphic standard procedures5 No. IIA and No. SI I respectively. Determination of Miscibilitv The boundary of the miscibility gap was determined by a modification of the method of Scheuer3 and of that used by Henry and Cordiano. As finally developed the method was as follows: A fused alumina crucible 25 mm id with 75 mm depth and 1.5 mm wall thickness was placed on the bottom of a container made from a 4-in. length of 1 1/2-in. iron pipe and pipe caps. ?&apos;he space around the sides of the crucible was filled with 40 mesh crystalline alun-dum. A charge of 60 g of aluminum and 10 to 15 g of sodium was placed in the crucible, the sodium first being trimmed and rinsed with iso-pentane to remove kerosene. The container was tightly capped, filled with argon (99.6 pct pure), and heated to the desired temperature (between 670 and 800°C). A positive pressure of argon (about 8 mm of mercury) was maintained through a small pipe to the upper cap. After soaking for from 2 to 5 hr, the container was quenched by directing a stream of water onto the base, so that solidification of the aluminum-rich layer was rapid and essentially unidirectional. Analyses were made on drillings taken from the bottom of the ingots after machining off the surface layers. Pre-

Jan 1, 1949

By E. Knell

COM Energy, Inc., a subsidiary of Occidental Petroleum Corporation, has constructed a 1.6 million hectoliter-per-year COM plant in Jacksonville, Florida. COM will be distributed to customers in the region as a substitute for fuel oil presently burned in boilers and kilns. As the market for COM grows, COM Energy, Inc. expects to build additional units both in this country and overseas. This paper addresses the overall status and technical aspects of the project, focusing on the facilities for COM production and utilization.

Jan 1, 1982

By Van H. Manning

The term war minerals has been applied t.o those ores and minerals that were largely imported. before the war. Among the mon important of these are manganese, essential for making high-grade steel for munitions and industrial use; graphite, for u,.akin1 crucibles; tin, for plating utAmsils and for bearing-met.al; mereury, used as fulminate t.o explode shells; pot.uh, for making fertilizer and explosives; tungsten and molybdenum, for high-speed t.ool steel; antimony, for hardening bul!et lead; chromite, for tool steel, for tan- , ning leather, and as a refractory lining in furnaces; magnesite, for :refract:A>ry linings; mica, as insulating material; platinum, for the manufacture of sulphuric acid and for electrical apparatus. When the United States entered the war it was clear that every ship would be needed and that the number available for importing minerals would be small. Hence a quick and thorough survey of domestic resources was necessary. . Throughout the war the scope and volume of the war-minerals work increased until it covered practically every mineral that was known t.o be or was liable to be in short supply.

Jan 1, 1919

By Xiaolong Bi, Shaohua Luo, Longjiao Chang, Shiyuan Cao, Jianan Liu

iliary agent was proposed. The mineralogical transformation and silicon extraction kinetics of laterite nickel ore in alkaline hydrothermal treatment were studied. The effects of reaction temperature (175 ~ 250℃), molar ratios of sodium hydroxide to ore (1.05 ~ 1.2:1), and laterite nickel ore particle size (44 ~ 178 μm) on the extraction ratio of silica were investigated by using the shrinking core model. The results show that the extraction ratio of silica increases with the increase of reaction temperature, sodium hydroxide to ore molar ratio, reaction time, and the decrease of raw ore particle size. The kinetic analysis shows that the separation of silica in laterite ore can be described by internal diffusion model. The apparent activation energy (Ea) of the reaction was 8.87 kJ mol− 1, and the kinetic modeling was established.

Dec 2, 2021

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.

By Louise Corriveau, Bronwyn Azar, Valerie A. Jackson, Luke Ootes, Jeff Harris

We use the results of new bedrock mapping, combined with geochemical point data and airborne radiometric data (in particular equivalent uranium concentrations) to help determine which geological units in the Paleoproterozoic Great Bear magmatic zone (GBmz) contain elevated uranium. The data collectively indicate that the highest primary uranium concentrations are in equigranular granites and subvolcanic/volcanic porphyries. Notably, these rocks host the majority of known uranium-bearing deposits and/or prospects in the GBmz. We speculate that the uranium in these deposits/prospects was derived from nearby, uranium-enriched rocks and was mobilized by much younger, circulating hydrothermal fluids. Sedimentary rocks of the Thelon and Dismal Lakes groups unconformably overlie the GBmz and are known to host unconformity-type and sandstone-hosted uranium prospects. Most likely, the uraniumenriched rocks of the GBmz acted as a uranium donor to these overlying sedimentary basins. The method of investigation employed in this study may be applicable to other ‘granitic’ terrains in order to identify regions with favourable rocks for uranium exploration.

Jan 1, 2013

By Karl J. Benecke

Though the first patent on a bucket wheel excavator (BWE) was granted in 1881 in the US, this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generation, despite the low heating value of German lignite on the order of 8500 kJ/kg (3600 Btu/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is on the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output mines. The largest one, Fortuna mine in the Cologne district, produced a total of 45 million tons of lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95.2 million bank m3 equal to 200 million tons of overburden had to be removed to accomplish this lignite output. The largest BWE ever built is working in the Fortuna mine [(Fig. 1)]. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 tons and its wheel diameter 21.6 m, as high as a seven-story building. Major reasons for the development of BWE technology in Germany were: ? Lignite deposits with moderately consolidated, alluvial-type overburden (gravel, sand, loam, marl, clay, etc.) ? Great overall depth of the deposits, ranging far beyond 100 m, requiring a wide opening of the mine, hence not permitting direct overcasting of overburden. ? Multiple-seam deposits of poor-quality coal divided by reject partings, which demand a perfectly selective digging tool for clean separation. In general, these conditions are almost identical to those prevailing in the lignite deposits of Texas and neighbouring states: The type of overburden suitable for BWE digging, the overall deposit depth ranges down to around 100 m, and finally, the multi-seam occurrence with partings between seams, the latter ranging from just 1 m to a few meters in thickness. Technique As the Texas-type lignite deposits come into focus more and more as a possible fuel source in power plants to replace natural gas and crude oil, the following will deal with the BWE technology for mining a typical Texas lignite deposit under the aspect of producing enough fuel for a 500-MW power plant located at the mine mouth.

Jan 1, 1980