Search Documents

By S. Partney

Waste clay ponds are a necessary part of the phosphate rock beneficiation process. They are large, averaging a square mile in size; unsightly, in that they protrude 20 to 50 feet (6 -15 meters) above natural grade; stabilization and reclamation is slow; and they have had a history of catastrophic failure. The State of Florida has never published a specific rule regarding the configuration or height of these ponds, but has enforced numerous policies along these lines. The current rules are given and interpreted, along with the reasoning for current policy. In addition, an overview of the history of the policies, and an attempt at explaining the reasons for the changes that have occurred is given. The industry has been forced to make major monetary decisions, having effect for decades on mine economics, in a constantly changing regulatory environment. The Bureau of Mine Reclamation is confident that a direction of regulation has been solidified, but changes are still to be anticipated.

Jan 1, 1998

By Rainer W. Kaiser

High wear resistant HSS rolls are being successfully used in the first stands of HSM finishing trains since the early 1990´s. The strong demand of mill administrators to make them applicable also in the last stands of the finishing rolling mill is a major influence factor of R&D efforts at respective roll suppliers. Looking back to the successful replacement of ICDP and HiCr rolls by more economic HSS rolls in F1-4 in regard to the TCO, rolling mill managers wish to repeat such scale gain also at F5-7 stands. Actually used enhanced ICDP rolls wear faster, being the HSM stoppage factor. F1-4 HSS rolls can be used for example 3 times longer. There is an obstacle to be overcome by roll suppliers and end users to replace F5-7 rolls by HSS rolls. Stick and crack resistance properties of HSS need to be improved. As a worldwide known leading producer of cast rolls for steel mills since 1820, the traditional German family owned foundry and machine shop IRLE, existing since 1693, accepted to face also this additional challenge. IRLE´s long year experience and prior researches have shown possible development directions to improve mentioned stick and crack resistance properties of its HSS grade, called SST. A new material of the HSS family is in the development pipe line and is discussed: SST/G. Choice criteria of the development direction, steps to control and guarantee respective sections of an industrial scale production as well as observations and results are described.

Jul 30, 2018

By Lukas Walder, Roland Arnold, Raphael Zuber, Richard Gradnik

This paper presents the construction of the ventilation shaft for the single-tube, doublelane Kramer tunnel. The project is located in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of Garmisch-Partenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million incl. VAT (US-Dollar 201 million), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for singletube tunnels is solved by a parallel escape tunnel passable for vehicles. For tunnel ventilation, an intermediate shaft has been designed with a depth of approximately 90 m (295 feet) and an inner diameter of 4.5 m (14.8 feet). All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). The geological and hydrogeological conditions, the change in the profile (from round to square geometry), and also the shaft being located at a high elevation presented a demanding technical and logistical challenge. The site arrangement with the pit bank was located in a cut, the slopes of which had to be stabilized with shotcrete and soil nails. This excavation was carried out from the fall of 2020 to the beginning of 2021 because construction operations had to be completed outside the nesting period of protected birds.

Jun 13, 2023

By R. Jacobs, R. E. L. Pobe

The Moab Khotsong Metallurgical Complex comprises a gold recovery circuit (Noligwa Gold Plant) and a uranium recovery circuit (South Uranium Plant). The metallurgical complex employs the reverse leach technology for the recovery of uranium; specifically, uranium extraction prior to gold using acid leaching processing. The inherent uranium species in the ore are uraninite, coffinite and brannerite. The slurry that has been subjected to the uranium leach is further subjected to solid-liquid separation to separate the uranium in solution through counter-current decantation and the solids (solids carrying all the gold), which are repulped and returned to the gold plant for gold processing. The uranium leaching process is critical to the uranium playing a pivotal role as a value adding by-product to the gold operation. The benefit of adopting this reverse leach process, for improved gold recovery, is that it exposes gold particles occluded within the uranium matrices and avails them for cyanidation. However, the drive for operational efficiency in uranium extraction must be weighed against the incremental operating cost against the backdrop of depressed spot uranium market prices. Over the years, efforts were directed at maintaining the benefit of extracting uranium to enhance gold recovery and simultaneously, optimizing the operating cost model for the uranium operation to remain relevant to the gold operation. The aim of this paper and the corresponding presentation is to give account of the uranium processing optimization journey embarked on over the years; namely, the operational trade-offs made in the process of ensuring that uranium continues to add value to the gold operation. These challenges were faced while striking a fine balance between processing cost and operational efficiencies against the prevailing depressed uranium spot market prices. Mineralogical- and laboratory tests conducted form the support basis for the results and observations articulated in the paper.

Jan 1, 2020

By Ana Paula Domingos Cardoso

Este trabalho descreve o desenvolvimento, as características técnicas para a produção do produto Usibor® 1500 pela ArcelorMittal. A viabilidade de produção destes materiais é decorrente do processo de otimização de operação e infraestrutura da sua linha de galvanização (Continuos Galvanizing Line). O trabalho engloba também características técnicas gerais do produto, microstruturais e mecânicas, assegurando conformidade com normas internacionais de qualidade do mesmo. Afim de conhecer a microestrutura e propriedades mecânicas do material Usibor®1500, antes e após conformação a quente será apresentados resultados de aplicação do material estampado industrialmente no setor automobilístico.

Aug 17, 2017

By Marcelo Ferreira Martins, Sandro Luís Zahner, Daniel de Paula Ferreira, Celso Dias Barão, Leandro Martins Pereira

O EOF é um forno básico a oxigênio caracterizado pelo conceito de pré-aquecimento da carga sólida baseado na energia da corrida anterior. Mesmo com um sistema supervisório, a operação era totalmente manual. O trabalho consistiu no desenvolvimento e implantação de modelos matemáticos, objetivando atingir a temperatura e composição química programada para vazamento. O sistema de equações consideram todas as entradas metálicas com as respectivas composições químicas e define a quantidade necessária de energético ou refrigerante, além da adição de cales conforme a basicidade e teor de MgO objetivados na escória. O desenvolvimento passou inicialmente por um conhecimento profundo do processo, dada a excelência e originalidade do forno EOF, que é diferente dos demais convertedores a oxigênio. A seguir, foram definidos padrões e práticas operacionais que garantissem a reprodutibilidade do processo, para, finalmente, permitir o cálculo através de modelos matemáticos. Com a automação do processo foram conseguidos expressivos ganhos de produtividade, redução no consumo de materiais, aumento do rendimento metálico e menor consumo de refratários.

Oct 1, 2019

By Kyle A. Perry, Ethan A. Steward

The mining of underground coal presents several hazards for miners, including the risk of an explosion fueled by methane gas and coal dust. Methane gas, produced during coal formation, can continuously leak into old workings and build up through its lower explosive limit. Underground coal mines are required to maintain safe conditions, either by ventilating old workings or sealing them off using approved methods. Seals must be designed to withstand instantaneous pressures for a minimum of four seconds. A design strength of at least 50 pounds per square inch (psi) is required for atmospheres monitored and maintained inert, 120 psi for non-inert or not monitored, and greater than 120 psi for special cases. Due to the high cost and testing environment availability, most mine seals are designed through calculations and computer modeling and not subjected to full-scale testing in a representative environment. High pressure is not the only threat that mine seals may be exposed to. During an underground explosion, pressure waves and gas expansion may propel common mine items and objects to a high velocity, generating enough energy to damage mine seals and reduce their strength. Damaged mine seals may fail to contain their rated pressure, allow high pressure gas and fumes to vent through the seal during an explosion, or allow gasses to leak through the seal later after an explosion has occurred. This paper examines the effects of high velocity impacts of common mine materials and items on a reinforced mine seal rated to 120 psi.

Jun 2, 2023

By J. Weijdema, D. N. Dietz

In the conventional underground combustion process (dry combustion) much heat is left behind in the swept formation and goes to rva.rte. Econonmy can be improved by heat recuperation through water injection. This is most advantageous if done at the earliest opportunity before much heat is dissiputed to cap and base rock. Water injected simultaneously with the air will flash to superheated steam, which passes through the combustion front together with the nitrogen from the air. A condensation front traveling up to three times as fast as the combustion front drives out the oil. In this type of wet combustion, the water evaporates before it reaches the combustion zone. The evaporation front travels more slowly than the combustion zone. If so much water is injected that the evaporation front overrun the combustion front, combustion in that spot will be quenched and some unburned fuel will be left behind. Air reacts with the oil farther down-stream where steam temperatures occur; at steam temperature, the air reacts rapidly with the oil. Velocity of the combustion front is increased thereby and is governed essentially by the water-injection rate. In the extreme case of high water-injection rate, a short heat wave of constant length is driven through the formation by water injection. Once this wave has been established, no more heat need be generated than that required to make up the heat losses from the short heat wave; a relatively low rate of air injection will suffice. The feasibility of partially quenched combustion has been confirmed in tube experiments. A heat wave at steam temperature is observed. Chemical analyses of flue gas indicate preferential burning of hydrogen while a carbonaceous residue is left in the formation. Introduction A disadvantage of so-called dry in situ combustion is that air-compression costs are rather high. An air consumption of about 400 std cu m/cu m (400 scf/cu ft) of formation swept is an accepted figure. This high consumption is mostly wasted since much heat is left behind in the depleted oil sand. Methods were investigated for recuperating as much as possible of the heat left behind. This paper deals only with basic principles and is confined mainly to one-dimen- sional flow without lateral heat losses; experiments were conducted in relatively narrow, well insulated tubes. If some water is injected with the air, it will turn to superheated steam in an evaporation front, which should travel behind the combustion front. The steam having passed the combustion front causes a steam drive by a condensation front that can travel faster than the combustion front. The latter needs to travel only part of the distance covered by the oil-displacing condensation front, and thus consumes less air. The water-air ratio would seem limited to that at which cold water overruns the combustion. This limitation was deliberately exceeded considerably in theory and experiments. It was found that combustion is then indeed quenched, but only locally. Farther downstream, the oxygen finds residual oil at steam temperature, which is suficiently high to ensure rapid oxidation. Thus, the combustion front uses only part of the available fuel because it is chased through the formation faster than its normal velocity. No heat is left behind. This new process is called "partially quenched combustion". At the upper limit of the water-air ratio, a small heat slug is moved through the formation by the flow of water and steam. Only a small flow of air is needed since it has only to generate sufficient heat to make up for the lateral heat losses of the short heat slug. Theory Although many factors complicate underground combustion, the processes will be presented in their simplest form. For this reason, one-dimensional flow without lateral heat losses is assumed. Heat conduction in the direction of flow also is disregarded. Under these conditions, dry combustion causes very high temperatures. The heat-carrying capacity of the gas stream is small. Heat generated by oxidation of a residual oil saturation is retained in the sand. The available fuel determines the air requirement and the temperature obtained. Accepting the often-mentioned air consumption of 400 std cu m/cu m (400 scf/cu ft) formation, we calculate a temperature of the swept sand of 1,200C (2,192F) (Fig, I). If water is injected at a modest rate with the air, it will flash to superheated steam upon contact with the heated sand. One cu m (35.31 cu ft) of hot formation will evaporate about 0.5 cu m (17.66 cu ft) of water, and thereafter will accommodate (at an estimated 0.80 saturation and an assumed 0.40 porosity) another 0.3 cu m (10.59 cu ft) of water in cold condition. As long as less than 0.5 + 0.3 = 0.8 cu m (28.25 cu ft) of water is injected for every 400 std cu m (14,125 scf) of air (water-

Jan 1, 1969

By F. J. Prokoski

The COALSTAR Project, which operated from November 1981 to December 1982, was a research and development project aimed at providing a reliable and inexpensive means of monitoring various waste site conditions via the GOES satellite system. The GOES system provides data transfer from unattended isolated sites where neither power nor telephone lines exist. The reliability and resolution of the data received while using the satellite link were excellent; however, the site instrumentation gave considerable trouble. The disastrous failure of a large coal waste embankment in 1972 led the Bureau of Mines to undertake a comprehensive program to reduce the likelihood of such an occurence again. Part of this program involved the installation of instruments to monitor the stability of a specially-selected embankment operated by Armco Incorporated near Montcoal, West Virginia. Initially, the instruments were monitored by normal telephone lines and used normal commercial power from the local utility. The project described here was initiated to replace this monitoring system with an unmanned, solar-powered data collection system which transmitted data via satellite to a central computer facility. The satellite data network is the National Earth Satellite Service of the National Oceanic and Atmospheric Administration.

Jan 1, 1984

By G. S. Scott

In the course of tire investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, come attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rise if the rate of generation of heat exceeds the rate of heat dissipation and will fall if the opposite is the cane. Factors that affect the rate of generation of heat are:

Jan 1, 1941

By Allen V. Reicks

Modern conveyor pulleys are welded steel structures subjected to dynamic loads. In this paper, fatigue notch and fracture mechanics methods are applied to several weld joints on typical pulley constructions. These methods are used to analyze field applications and are correlated with laboratory testing. Generalized approaches are presented which provide high confidence in pulley design with corresponding high reliability.

Jan 1, 1996

By John M. Kelly

This report covers the development, exploratory drilling, and production of oil and gas in New Mexico during 1945. The statistical information was gathered from state regulatory agencies and other sources believed to be reliable; it is presented here in combined form for general information only, and the author assumes no responsibility for its accuracy or completeness.

Jan 1, 1946

By N. Hamlef

In this study, the effects of heat treatment on phase formation and surface morphology of the Cr-Pt coated system are investigated using X-ray diffraction and electron microscopy techniques. The CrPt andCr4Pt (Cr3Pt - A15 type) phases were formed after heat treatment of the coated samples. Heat treating at 1000°C renders a distinct island coating morphology that is non-continuous in nature. A diffusional model is proposed for this coated system with regards to the surface morphology formation after heat treatment.

Jan 1, 2014

By E. G. King

This report contains experimentally determined heat-content values for cerium dioxide and Columbium (niobium) dioxide in the temperature range from 298° to 1,800° K. There are no previous similar data for Columbium dioxide, and those for cerium dioxide have an upper limit of 373° K. The heat-content and corresponding entropy-increment data are presented in tabular form. Equations were derived to represent the heat contents and heat capacities. The data for cerium dioxide are entirely regular, but those for columbium dioxide show two previously unreported anomalies at 1,090° and 1,200° K.

Jan 1, 1961

By A. S. Polubinsky, V. P. Chernyak

A further development of the theory of heat- and mass transfer in the system “strata - mine opening" is necessary for an improvement of the existing technique of heat calculation of mines and other underground constructions. A generalized boundary problem of heat- and mass conduction in strata around an opening as a theoretical ground for that purpose and several particular situations, important from the point of view of an opening and surrounding strata heat state analysis, as well as results of numerical experiments executed for such analysis are presented.

Jan 1, 1997

By Newell R

The influence of layering on the rate of heat transfer through a packed bed consisting of particles of two different sizes and heat capacities has been determined by measuring the heat front velocity through beds of quartzite particles and iron ore pellets. The heat front velocity through the layered beds was less than that through a bed consisting of a random mixture of the par- ticles. This is due to the formation of an interface in which the smaller pellets in one layer penetrate into the layer of quartzite Below.

Jan 1, 1987

F. N. SPELLER (communication to the Secretary*).-It would certainly be interesting to know more about the heat balance in this practice, but there seems to be no doubt that the net result is a greater absorption of heat where roll scale is used instead of solid metal scrap. In the experimental heats referred to, about an equal weight of pig iron or steel scrap was replaced by roll scale. This caused a reduction of about one-third in the time of blow compared with a heat of the same

Jan 6, 1917

By A. R. Laplante

Ten guiding principles in the design and operation of gold gravity circuits are presented: economic impact, applied mineralogy, gold's behavior in grinding circuits, alternate recovery approaches, reliability vs. performance, gold room operation, scale-up, screening, feed rate and recycling. The principles are explained and their application illustrated with case studies. Conflicts in principle application are also discussed.

Jan 1, 2000

By William C. Geitz, Dan Fitzgibbon

Lightning has always posed a serious threat to blasting operations, especially within the mining and construction industries. In recent years, technological advancements in communications systems and microprocessors have significantly improved the accuracy and efficiency of lightning detection and warning instrumentation. These advancements have increased the availability of highly reliable, accurate and affordable systems for use within the explosives arena.

Jan 1, 1991

By Charles Rich, Robert Munson, Leonard Obert

Improved methods of predicting the caving characteristics of ore bodies is discussed. Experiments were conducted at Climax mine, Climax, Colo., on varied rock compositions. The cavability of adjacent areas, as well as seismic energy absorption proved to be good factors in determining cavability. Seismic velocity, core recovery, and rock quality designation (RQD) were found to be not as reliable.

Jan 1, 1977