Search Documents

By Jung-Hum Lee, Young-Joon Lee, Eui-Joon Hong, Seon-Hong Kim, Chan-Dong Kim, Keon-Woong Jeong, Ki-Lim Kim

"Subsea tunnel needs to be built over 50km long to connect between nations and continents. However there are only 19 tunnels longer than 5km in Korea, and there is no history of constructing and operating a tunnel longer than 50km. As the concept of a subsea tunnel, which withstands high water pressure and has an extremely long length is completely different from that of a land tunnel, all kinds of the latest technologies for tunnel construction are required such as survey and analysis of geology, design and construction under high water pressure, ventilation and prevention of disasters within an ultra long tunnel. Therefore, this paper describes the determination of tunnel cross-section under a high speed railway, structural stability, ventilation and fire safety under construction and operation, etc. through the virtual project for the length of 108km subsea tunnel under high water pressure of maximum 20bars from Honam to Jeju island in Korea. 1. INTRODUCTION The Honam-Jeju virtual project is subsea tunnel project to link from Honam(land) to Jeju(island) extending the currently operating Honam high speed railway line, and the same express train(t=18, design speed 350km/h, total train length 200m) operating at Honam line is applied in this project. As Honam-Jeju site is approximately 80km in straight distance with 160m maximum depth, subsea tunnel project should determine the various issues such as air quality/ventilation, aerodynamics, temperature, drainage, fire & life safety, structural stability. Figure 1. is the plan of subsea tunnel, with be constructed using Shield TBM. This double tube-Single track is composed of cross passages (every 350m in general section and 40m in emergency station), service tunnel, pressure relief ducts (every 250m), cross-over tunnels, shafts and emergency stations. 2. ALIGNMENT AND SITE CONDITON This project is planned as an ultra long tunnel of total length more than 105km via existing islands between Honam and Jeju island because straight alignment requires an artificial island which has high cost and construction risk, by deep water depth, though this is the shortest distance (see Fig 2). Water depth and topography in project site is divided into two blocks by Chuja Island. In first block to Chuja Island, depth of the water is 40m on average and maximum 60m, which indicates gradual change of water depth relatively. Also, outcrop bedrock is widely distributed near island."

Jan 1, 2016

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system, or systems, thus disclosed. Of the several systems initially investigated and evaluated, four showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By J. Howard Bird

The purpose of this publication is to discuss grounding mediums and the phases of grounding related to corrosion and cathodic protection. The material presented is believed to contribute to a better understanding of this subject. It also indicates more effective methods of reducing corrosion damage to metal structures and equipment in the mining industry by cathodic protection. The authors do not intend to discuss technical aspects but rather to explain the general principles of this method of inhibiting corrosion. The relationship between soil resistivity, protective grounding, and corrosion is presented. Corrosion causes the annual loss of billions of dollars; which can be greatly reduced. Losses in the mineral industry can be excessive owing to the extensive use of direct-current power, the presence of considerable dampness, and the frequent, indiscriminate use of dissimilar metals.

Jan 1, 1958

Gus C. Henning, New York City: In taking up the discussion of these specifications it is necessary that I give definitions of what I understand under the term " Specifications." There may be three kinds, viz.: (1) Specifications in general; (2) Standard Specifications; (3) Standard International Specifications. 1. A Specification is a document used in commerce which should clearly define the qualities of material to be supplied by the producer, the tests which shall be applied for their determination, and the methods which shall be applied for the purpose of determining that the entire product shall possess such qualities, properties and finish as are desired. The terms used in such document must be applied in accordance with their strict technical definitions as used by those most conversant with them, and the language should be of such accuracy that there can be but a single interpretation of each and every clause. A specification is a part of a contract, and should be legally perfect and accurate. Inaccuracy of definition and dic-

Jan 1, 1903

The design, specification, and performance evaluation of the Communications and Location portions of a Coal Mine Rescue and Survival System are described. The work was performed as part of a nine month effort to develop a mine rescue and survival system using existing technology and state -of-the -art hardware as recommended by the National Academy of Engineering. Three basic subsystems were developed, one for survival, one for communications/location and one for rescue. This report and related equipment manuals describe only the Communications/ Location Subsystem which was designed, fabricated, and tested by the Westinghouse Georesearch Laboratory in Boulder, Colorado. Two basic technologies were used. Electromagnetic signals propagating through-the-earth provide voice downlink and coded beacon up-link communications. Seismic methods were developed to provide means for locating trapped miners. Seismic signalling also provides a backup means for communications. Parallel development programs for the electromagnetic and seismic portions of the system were conducted. The resulting hardware and software have been partially tested in coal mines and under simulated emergency conditions in order to evaluate system performance. The results of these tests are discussed. Further testing is recommended in order to establish quantitative performance limitations tinder a variety of environmental conditions and to develop methods for improving system performance.

Jan 1, 1971

By W. C. Hirt

Deposits of ferromanganese crust containing cobalt and nickel occur on the seafloor in the Pacific Ocean near the Hawaiian Islands and Johnston Atoll. This paper describes developmental flotation metallurgy to separate crust from its associated substrate gangue. Important variables in ferromanganese crust flotation include reagent type, aeration rate, conditioning time and agitation intensity, pH, temperature, water type, and feed size distribution. Flotation in seawater of minus 600 ~m (-28 mesh) material assaying 6.2% Mn, 0.2% Co, and 0.13% Ni with diesel fuel-crude tall oil-sulfonate collectors produces concentrates assaying 15% Mn, 0.6% Co, and 0.3% Ni with recoveries of 89-95% while removing 62% of the feed weight.

Jan 1, 1990

By Franklin Bache

THERE seems to be in the public mind, and even in the minds of some coal-operators not experienced in mines subject to dust-explosions, a feeling that there has been something mysterious at the bottom of a number of recent American colliery-explosions. It has been declared in cases of accidents in mines regarded as particularly well equipped, in which every preventive precaution was said to have been taken, that the explosions were incomprehensible, and resulted from causes beyond the present knowledge of the practical coal-operator. But it is safe to say that no explosion has taken place which could not be explained by reasons well understood by most operators. The LT. S. Geological Survey Test Laboratory, recently inaugurated at Pittsburg for the reported purpose of investigating scientifically the matter of explosions in mines, will discover no new explanation of explosions. It call, however, co-ordinate the previous investigations of similar boards in England and on the Continent; and it may do a vast amount of good by promulgating widely, and in a form comprehensible by the most unlettered miner, certain facts and obvious deductions that cannot but have an effect in reducing the number and extent of the mine-disasters which, in the last few years, have been so terrible in frequency and magnitude. The only possible sources of explosions of any magnitude in coal-mines are : (1) explosives stored in quantity in the mine; (2) gases generated or liberated in the mine; and (3) coal-dust. Combinations of any of the three may, of course, take part in the result. The danger of any great loss of life from stored explosives alone is very remote. The simplest ordinary precaution forbids the presence, in one place underground, of any considerable quantity of explosives, and it would require an

Aug 1, 1909

By Richard D. Miller

This publication contains routine analyses and related source data for 295 natural gas samples from 18 States collected during calendar year 1963 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863/ and 576.4/

Jan 1, 1965

By N. Hwang

There has been increasing interest in the use of robotic machines, and several prototype robotic machines have been developed to automate the grit-blasting process for the purpose of steel bridge maintenance. To utilize such a robotic grit-blast machine effectively, the first consideration is automating the determination of the rust surface area to blast, on the basis of standards of practice, in a rapid manner. This study aims to propose a method to rapidly and accurately determine the rust surface area on steel bridges to blast, with consideration for the standards of practice, from images acquired via a blasting machine. The first step is to perform a color space conversion to transform the input image from a red/green/blue (RGB) color space to a hue/saturation/intensity (HSI) color space. The next step is to detect the presence of rust, using pixel-level classification via the C4.5 decision tree algorithm. Then it is necessary to confirm the blasting area by verifying whether the rust detection result satisfies the specified criteria on the basis of standards of practice. The proposed method was validated on 39 test images with various characteristics with respect to the degree of rusting and rust distribution type. The experimental results showed that the average accuracy rate of rust area classification was about 97.63%, and the success rate of the final decision of blasting area determination was 100.00% for 39 test examples. The whole processing time took an average of only 0.86 seconds per image. The preliminary results demonstrated that the proposed method not only determined whether rust was present in an image and the amount of rust but also indicated whether blasting was necessary, and, if necessary, it rapidly specified the rust surface area that should be blasted on the basis of standards of practice. The proposed method could be successfully incorporated into a robotic grit-blast machine.

Aug 1, 2013

By John P. McDonnell

Cable supports offer several advantages over traditional secondary support methods by enhancing stress redistribution to pillars and gob areas, minimizing or eliminating timbers and cribs that reduce ventilation, eradicating material-handling injuries related to placement of crib supports, and providing a cost-effective alternative to secondary support. The U.S. Bureau of Mines, in researching alternatives to traditional roof support methods, designed and installed high-strength cable supports to improve the stability of longwall gate road and bleeder entries in a Western U.S. coal mine. With the cooperation of industry, methods were developed to install cable supports in a tailgate and bleeder entry test area using traditional resin cartridges. Resin-grouted cable bolts were also installed and evaluated in additional longwall gate road and bleeder entry systems at the study mine. The cable-bolted areas successfully maintained roof support throughout the tailgate and bleeder entries. Cable supports replaced wood cribbing as secondary support in the bleeder entry system and minimized the use of cribbing in the longwall tailgate entries. This report describes the theory, application, and advantages of cable supports and presents mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 2010

By Cecil Harriss

Philip Environmental Services Corporation's (Philip's) innovative fluidized bed thermal desorption system recovers mercury from contaminated soil. Referred to as the Thermal Recycling System, Philip has constructed a mobile thermal desorption system that has a processing rate up to five tons per hour. The system includes a continuous-feed system, all radiant heat, inert gas atmosphere, hot gas filter, two-stage cooling, and a water treatment system. Based on treatability studies, the processed soil can meet cleanup objectives as low as two milligrams per kilogram and passes the mercury toxicity characteristic leaching procedure test.

Jan 1, 1996

By E. A. Holbrook

The data in this bulletin were obtained during an investigation of screening practice by the University of Illinois engineering experiment station and the United States Bureau of Mines under a cooperative agreement between them and the State of Illinois Geological Survey Division. Earlier work on this subject includes a study of the general practice of coal preparation in Illinois, made in 1914 and published in 1916,1 and an investigation of Illinois coal-washing methods, results of which were published in 1912 in a bulletin 2 that contained complete information on the methods then in use for sizing washed coal. OBJECTS OF THE INVESTIGATION The present investigation was limited to a study of screening as applied in preparing mineral products with the expectation of obtaining more comprehensive information on screening machinery.

Jan 1, 1925

By George H. Davis

Much concern has been expressed recently as to whether water supplies will be sufficient to support accelerated energy development foreseen in operation Independence. Taking the Nation as a whole, sufficient water is available for energy growth, but locally, as in arid parts of the Colorado Basin, limited water supplies will dictate economies in water use and affect plant siting. As Young and Thompson1 point out with respect to electric power generation, the term "water requirements" is misleading, as demand for water for cooling is sensitive to price of water and thus is quite flexible rather than the inflexible or fixed level implied by the word "requirement." Much the same is true of other energy conversion systems. Water is used in many aspects of energy production including mining and reclamation of mined lands, on-site processing, transportation, refining, and conversion to other forms of energy. In the East, South, Midwest, and along the seacoasts, water supplies are generally adequate for energy industries; most water problems in those regions relate to pollution rather than supply. West of about the 100th meridian, however, runoff is generally less than potential diversions and energy industries must compete with alternative uses for the limited available water supplies. Water is especially short in areas of less than 10 inches mean annual rainfall where natural precipitation generally is insufficient for establishing vegetation without irrigation. Extraction. The principal categories of extraction comprise coal mining, oil and gas production, uranium mining, and oil shale mining.

Jan 1, 1974

By J. D. Miller, C. L. Lin

"The use of 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles ranging in size from 150 mm to 1 mm at a voxel resolution of about 150 µm is now possible. This is quite a significant advance in X-ray tomography technology and promises to be useful for plant-site coarse particle characterization—size, shape, composition, density, texture, grain exposure and mineral liberation—with a response time of minutes after receiving the sample. This paper discusses applications in the mineral industries, including the coal industry, aggregates industry, metal mining and the processing of industrial minerals.IntroductionPlant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants and mineral processing plants is needed to improve plant capacity, product quality and/or process efficiency. Not much online coarse particle characterization is being done at these plants. Only some limited information regarding particle size is obtained online from reflected light images using analyzers such as the OPSA, Split and WipFrag™ analyzers. Even the laboratory analysis of coarse particles has been difficult because of the large amount of sample required to ensure statistical significance of the results. During the past several decades, laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage (Miller and Lin, 2004, 2009).Three-dimensional X-ray tomographic analysis has its origins in the medical services industry, where it is used to provide internal images of the human body. It has since been developed for nonmedical applications as well (Banholzer et al., 1987). Figure 1 shows a schematic diagram of the cone-beam geometry micro-CT system. In our case, X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two-dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a threedimensional image is reconstructed from the collected set of projection images."

Jan 1, 2016

By Samuel S. Wyer

THE installation of the gas-producer power-plant in America has been so unusual that all engineers have viewed it with in¬terest; a large majority, however, regard it with a lack of con-fidence and many with positive distrust. Despite the fact that European engineers have usually been less inclined to take the initiative along experimental lines than are Americans, they have, nevertheless, developed the gas-producer plant to a very high state of efficiency to which they were forced by the neces¬sity of economy in fuel-consumption. The gas-producer power-plant is so common in Europe that engineers as well as the general public regard it with the same degree of confidence that is now universally placed in steam¬plants. Gas-engines, both small and large, are in general use there, and central stations, aggregating several thousand horse¬power, are quite numerous. The fact that gas-producer power-plants have received so little attention in America may be attributed to five conditions:-1', ignorance and prejudice; 2, newness of work; 3, in-

Mar 1, 1905

By Andy Hudson, Stuart Brashear, David Lilly

Because of greatly increased timing accuracy, electronic detonator systems are a well-known and widely accepted major tool to control and reduce ground vibration. At a Southeastern quarry the authors found that the use of electronic detonators improved the reliability of the well known cubed root scaled distance equation for determining air blast. In addition, the authors noticed significant correlations between selected major peak particle velocity frequencies and air blast magnitudes. The major peak particle velocity frequency alone is a close approximation to air blast magnitudes. This relationship is not as significant or not always evident when standard pyrotechnic initiation systems are used.

Jan 1, 2009

By W. Perkins

The Smoky Canyon Mine has recently installed a PROMPTED GAMMA NEUTRON ACTIVATION ANALYSIS (PGNAA) on-line analyzer as part of a long-term advanced process control program. The on-line analyzer was adapted from a continuous dry analyzer and a large on-stream wet analyzer to a compact, multiplexed 3" slurry analyzer. The analyzation feed system utilizes a multiplexer system to accommodate up to fourteen (14) different plant process streams. The corresponding sampling system also provides for dewatering of sample streams too dilute for timely analysis. Key analysis includes, but is not limited to, phosphorus, aluminum, magnesium, calcium, and potassium. This data currently allows plant operations to be manually evaluated and controlled. Future development of a plant-wide supervisory control system will utilize the data for plant operations. This paper discusses the design, installation, and operation of the PGNAA on-line analyzer at the Smoky Canyon Mine.

Jan 1, 1996

By Jupneek Singh, Zachary A. Kiehl, Leila Safazadeh, Gareth Kennedy, Eleonora Widzyk-Capehart, Jeremy W. Ward

Mine workers are continuously exposed to a host of nonfatal stressors and potentially fatal hazards: noise exposure, excessive vibration, poor air quality, toxicant exposure, ignition of combustible gases, equipment-related accidents, and thermal heat stress. Wearable or portable sensors and contextual analytics provide a platform to unobtrusively collect and fuse multimodal health and safety data in real time to compute both acute safety and longitudinal health insights. This paper presents preliminary trial results, conducted by Simtars, VigiLife, Inc., and Queensland Mines Rescue Service, of the application of wearable sensors to monitor heat stress and other vital biometrics for mines rescue personnel.

Feb 1, 2024

By C. Bester, G. M. Rohde

A major challenge in the mining sector is the responsible management and efficient storage of mine residue. Over recent years numerous tailings dams have experienced unintended spills and failures, with severe consequences for the mining industry, the environment, local communities, and the regional economy. The fourth industrial revolution (4IR) is impacting society due to increased interconnectivity, processing speed, and automated technologies. This paper explores whether 4IR technologies have the potential to mitigate risks associated with tailings dams. Experts in the field of tailings dam operational management were surveyed to determine their view on the risks associated with tailings dams and the potential of 4IR technologies to mitigate these risks. The survey found that a majority of experts believe that certain 4IR technologies have the potential to reduce the risks associated with tailings dam failures.

May 27, 2025

By John Anthony Vasquez

During the last years Riva Acciaio Verona has taken the decision to invest in the route of a fully automated meltshop. The aim is to reduce at the minimum the operator's intervention from the bucket preparation till the ladle transfer to the continuous casting bay. The foundation for achieving the goal is the introduction of innovative technological solutions (fully automated cranes for bucket charge in the EAF, robots for sampling, etc. The paper underlines how the different solutions are based on the best practices to improve operator's safety and describes the different steps of the project, the different solutions adopted and the results in terms of production, energy savings, cost reduction and improved safety. Details are presented for: scrap yard management and bucket preparation, EAFs centralized controls and related robots for auxiliary operations (sampling, EBT cleaning, scraper for slag door automation, complete mass & energy balance based on process control), LFs centralized controls and process integration.

Aug 16, 2017