Search Documents

By W. D. Delahaut

Sampling tests performed at the Paradise Peak Mine compared various blasthole samplers and reverse circulation sampling methods. Statistical analysis of the data indicates that be-low-the-deck bag sampling produced a 24 to 29 percent error when compared to bulk sampling methods. Use of a chip pile wedge sampler reduced error to 17 percent. Reverse circulation sampling upgraded over bulk blasthole sampling by 7 percent for gold and 11 percent for silver. These results indicate that bias sampling conditions exist when small volume bag sampling is employed in production blasthole drilling.

Jan 1, 1991

By Rita Aiello, Stan Mack, Peter Werth, Joseph McCarney, Jozef Stachulak

"Johnson Matthey has developed the first diesel particulate filter (DPF) for underground mining that controls particulate matter (PM) at the same time as maintaining emissions of NO2 at or below engine baseline levels. DPF technology is critical for controlling PM which is classified as a carcinogen, but passively regenerating systems rely on the use of oxidation catalysts that can potentially increase NO2 emissions. This paper reviews the development of low-NO2 PM control technology and the results from testing this technology underground on diesel mining equipment. KEYWORDS Decomposition catalyst, Diesel particulate filter (DPF), Diesel particulate matter, Mining Continuously Regenerating Trap (CRT®), NO2, SCR INTRODUCTION The introduction of diesel particulate filter (DPF) technology on heavy duty diesel (HDD) engines has been an important step towards addressing the clean air and health concerns for mining companies. Control of diesel particulate matter (PM) emitted from diesel engines is already being implemented for on- and off-road vehicles, and similar legislation is being prepared for mining equipment. In addition to PM, the diesel emission control strategies (DECS) also reduce carbon monoxide (CO) and hydrocarbons (HC). Some DECS control oxides of nitrogen, or NOx, which is composed of NO and NO2. Johnson Matthey has led the development of emission control technologies for diesel engines for almost 30 years. Over the last ten years alone JM has supplied over 3 million Continuously Regenerating Trap (CRT®) DPF systems for on-road vehicles, and over 200,000 systems for off-road vehicles. The patented CRT technology combines a diesel oxidation catalyst (DOC) with a DPF to effectively trap harmful PM from diesel exhaust, while removing CO and HC. The DOC converts part of the engine NOx to NO2, which reacts with the trapped soot to regenerate the filter. As engines become more fuel efficient, less waste heat enters the exhaust. This can be a disadvantage for after-treatment systems as it leads to lower catalyst operating temperatures. The CRT system regenerates passively, without addition of heat, at temperatures that are typical of diesel engine exhaust. JM recently launched the Mining CRT system which integrates CRT technology with NO2 abatement to reduce PM and tailpipe NO2 from underground diesel mining equipment. This is the first technology proven to control both PM and NO2 emissions for a cleaner, healthier working environment. The Mining CRT is also cost-effective compared to other technologies."

Jan 1, 2019

By Daniel I. Carey

Current and potential dragline reclamation usage was evaluated for the U.S. coalfields based on data gathered and analyzed during field surveys, literature reviews and contacts with manufacturers. It was concluded that current wining plans have been adapted to federal and state strip mine and reclamation laws in ways which limit the potential for drag line reclamation systems at active mine sites. At abandoned conventional contour mine sites in steep-sloping areas such as central Appalachia, however, it was found that dragline reclamation systems have great potential application and may be the only practical solution to many reclamation problems. Alternative dragline systems were examined for restoring abandoned sites, and it was concluded that a tower excavator system offered superior characteristics and should be evaluated and developed under field conditions. A testing program was developed to provide a framework for the monitoring and analysis of cost, production and environmental data during a field demonstration of a tower excavator system.

Jan 1, 1981

By E. Ferguson

In evaluating refractory designs for cast house applications, thermal calculations are frequently performed to determine cold face shell temperatures, temperature profiles and metal freeze plane locations within the refractory layer, and heat loss in the steady state condition. A problem arises when looking at molten metal transport crucible designs in that these structures are usually operating under non-steady state conditions throughout their production cycle. Because the molten metal temperature varies with time, and material properties such as thermal conductivity are temperature dependant, mathematical solutions are at best... complicated. This paper presents a relatively simple, iterative solution, that can be set up on a standard computer spreadsheet program, to calculate heat transfer in non-steady state conditions. These calculations can provide curves for (1) molten metal temperature vs time and (2) cumulative heat loss vs time, given variable starting conditions, to aid in the evaluation of molten metal transfer crucible refractory designs.

Jan 1, 2004

By A. T. Yu

There are compelling reasons for us to look to our Country's Western coal. Despite its inherent low BTU content, Western coal's low sulphur content provides a near-ideal answer to satisfy our in- dependent goals of clean air and self-sufficiency in energy. Vast reserves, thick seams and amenability to low-cost strip mining serve as a powerful economic basis for its viability as a primary and dependable source of energy for the coming decades. A major consideration, the solution of which may not be quite obvious, is transportation cost. These abundant deposits are remote from the utilities of the heavily populated eastern regions of the United States (Figure 1). A Western coal mine in Montana is likely 1500 miles or more from an eastern power plant. The comparable distance to an eastern coal mine may be only 200 miles. Thus, the question is: How can the haulage cost of our Western coal be substantially reduced to an acceptable level? If resolved, western reserves of coal will be one of the key solutions to satisfying our Nation's energy needs.

Jan 1, 1975

By Shklyar FR, Bokovikov BA, Gordon YM, Scherbatskii VB, Yaroshenko YG, Shvydkii VS

The paper presents, for the first time, a complete mathematical model of the flow of gases in packed beds which describes the processes of gas-mechanics in iron blast furnaces and other shaft type smelting units. Good correlation between calculated and experimental results was obtained confirming the adequacy of the model. It is shown that the uniformity of gas distribution is related to the tuyere size and the extent of its protrusion into the furnace and that these variables may be used to regulate gas distribution across the furnace diameter. It is also concluded that furnace height has no significant influence on gas distribution. The necessity for a mathematical description of raceway phenomena has been experimentally proved. Conclusions from theory are shown to have profound implication to furnace design and operation.

Jan 1, 1975

By ERIK CHARRIER, HUGH MILLER, JOSEF BOURGEOIS

In this study, a unique excavation system was characterized, utilizing waterjet technology as the primary tool for material removal during rehabilitation of reinforced concrete and shotcrete structural liners. Through empiric testing, this research seeks to validate the hypothesis that waterjet removal of these support systems will result in less unintended damage than conventional removal methods. The intent is to develop a viable technology that will reduce the collateral damage caused to surrounding liners during excavation, improve the adhesion between shotcrete and the substrate for longer lasting ground support, and improve overall safety for workers in underground environments. An analysis on the fracture mechanisms and operating parameters of each method was completed. Instrumented shotcrete panels were physically tested and examined through visual inspection and ground penetrating radar (GPR) to compare substrate damage according to each testing method. After testing was completed, the data strongly indicates that waterjet cutting causes less collateral damage to the surrounding intact liner and substrate when compared to that of conventional impact hammers. This research is intended to provide a scientific basis for additional applied research in the rapid excavation and repair of shotcrete support systems.

Sep 23, 2021

By Diego Quiroz, Francisco Cuellar

Existen tareas esenciales como la exploración, inspección, y digitalización de galerías subterráneas que pueden presentar un alto riesgo para los trabajadores ya que se pueden producir accidentes. En este contexto, se hace necesario buscar soluciones más eficientes y seguras para la exploración, inspección, y digitalización de galerías subterráneas en la industria minera. Se propone como solución el uso de un robot terrestre no tripulado capaz de desplazarse en superficies irregulares para la digitalización, inspección, y diagnóstico recurrente y seguro de la infraestructura de galerías subterráneas en minería.

Sep 29, 2023

By J. D. Campbell

"Coal is one of Alberta's major fuel resources, but its distribution, especially in the flat plains region, has been somewhat obscured by surficial deposits. After a period of neglect, easily strippable plains coal is presently approaching a position of dominance in electrical power production, a position it is likely to retain for a number of decades in the face of strong competition from hydro and nuclear power. Accordingly, the Research Council of Alberta has undertaken an inventory survey of the province's supplies of this resource.In the southern part of the province and in the north-central forest-fringe area, some strippable coal is found in the Belly River Formation and its equivalents, but major strippable coal reserves in large areas of central Alberta occur within the Edmonton Formation. The survey is planned on a reconnaissance scale, drilling test holes at 2-mile intervals in selected large areas. It appears to show that, in well-settled regions, large reserves of strippable coal are only to be expected where they have long been known; major presently unknown bodies of coal must be sought in unsettled regions or at depths too great for strip mining. However, such bodies might still be economically competitive with hydro and nuclear power in the production of electric power for some time to come."

Jan 1, 1967

By Pamela J. Watson

A novel technique has been employed by the U.S. Bureau of Mines to determine the zeta potential of particles for a far-reaching series of material types in a wide variety of baseline waters, both alone and with many different chemical additives. The materials tested ranged from naturally occurring Sioux Quartzite and Tennessee marble to commercially produced magnesium oxide bricks. The waters tested ranged from ultrapure distilled, deionized water to municipal tap water and mine-site water. The chemical solutions tested included inorganic additives, such as aluminum chloride (AICI3) and sodium chloride (NaCl); organic additives, such as dodecyltrimethyl ammonium bromide (DTAB); and nonionic polymers, such as polyethylene oxide (PEO). The results of precise zeta potential determinations have application in a large number of laboratory studies as well as in various mining and processing operations.

Jan 1, 1989

By Thomas P. Battle

Modern-day direct reduction of iron first developed as a small-scale, low capital and operating cost alternative to the blast furnace. Since commercialization of continuous DR technology in the late 1960s, the market for the products of direct reduction has grown to more than 74 million tonnes in 2012. The initial advantages of DR plants over BF facilities have grown over the years, for several reasons, including the increased size of DR modules, lower energy and emissions (particularly CO2), along with the flexibility to use a number of different reductants. The development of DR technology over the past forty years will be emphasized in this presentation, including recent developments that allow for even more direct sustainability comparisons with the iron blast furnace – and even combine the two technologies for improved synergies. Also briefly discussed will be the possibilities of using direct reduction for non-ferrous ores.

Jan 1, 2014

By George S. Rice

This bulletin traces the growth in the belief in the explosibility of coal dust, summarizes the experiments and mine investigations that have established this belief, and gives the present status of pre- ventive measures. It has been prepared in accordance with the pro- visions of the acts of Congress authorizing investigations relating to the causes of mine explosions, and contains references to and descrip- tions of experiments made at the Federal testing station at Pittsburg, Pa. This station was inaugurated under the United States Geo- logical Survey, and was transferred to the Bureau of Mines on the establishment of the latter on July 1, 1910. Only within comparatively few years has the dry dust of bitumi- nous and lignitic coals been generally recognized as an explosive agent more insidious, threatening, and deadly to the miner than fire damp. Fire damp carries its own flag of warning-the "cap" in the safety lamp-but coal dust, though visible, does not attract attention until present in large quantities. Fire damp is of local occurrence, and except in notable and very exceptional cases is controllable by careful manipulation of ventilating currents. If by mischance a body of fire damp is ignited in a mine, the force of the explosion may be terrific, but the effect is local unless dry coal dust is present, or unless (as it very rarely happens) an explosible mixture of methane gas and air extends through large areas of the mine. In a dry mine dust accu- mulates everywhere, and the blast from the ignition and combustion of bituminous dust may traverse miles of rooms and entries and wreck structures at the entrance to the mine. The comparative potential destructiveness of gas and of bituminous dust is strikingly shown by the history of the Pennsylvania anthracite mines. These mines not infrequently have large inflows of gas, and the resulting mixtures of gas and air have sometimes been ignited, yet no such wide-sweeping explosions have taken place, despite the presence of dry anthracite dust, as have happened in excellently ventilated bituminous mines.

Jan 1, 1911

By M. Hamamoto, S. Tanaka, K. Noda

"Tamano Smelter or Hibi Kyodo Smelting Co. Ltd. is operating with the Tamano Type Flash Smelting Furnace method which is a flash smelting furnace without slag cleaning furnace but which can discharge a slag equivalent to that from the slag cleaning furnace and with the development or coke combustion technology which is the basis of this world's only one type flash smelting furnace process, the smelter exhibits a low operation cost under high productivity operation. Utilizing this experience and improving it we have developed and put to practice an operation guide system using a general purpose computer in order to further establish s stable operation. In this paper these improvements are described. Background of System DevelopmentWith the recent rapid progress of general purpose computers and improvements in their performance an environment for the use or computer in process simulation at low cost and simple operation has been established. If an accurate operation simulation can be done with the Tamano Type Flash Smelting Furnace the merits would be very great and thus we started development of the system. The official name of this system is Computer guide system for Coke Combustion in the T-FSF and taking the initial letters we call it CCCT. We aim to achieve operation with stable mane grade, temperature and slag loss in the furnace by maintaining the most suitable combustion conditions of concentrate and coke in the flash furnace with the assistance of CCCT to the flash smelting furnace operators.Through several production expansion projects clone in the past by oxygen enrichment the copper concentrate treatment quantity and matte grade have increased step by step as shown in Figure I. Following this increase the difference between the operation calculation results al the initial stage of coke combustion and the actual behavior of furnace (matte grade. temperature in the furnace. etc.) gradually became bigger. Further operation procedures taken by different operators against the same phenomenon were sometimes different depending on each individual, which from time to time caused the operation to become unstable. Prior to the development of the system we checked out thoroughly the weak points of operation calculation procedures which were in practice until that time. The results were analyzed and study was carried out to establish a most suitahle operation calculation procedure and finally we reached this system"

Jan 1, 2000

By V. Matthews

"INTRODUCTION Typical grinding electrification requirements are defined by high power, constant torque and slow speed. Dual pinion mills also include a need for tight tolerances in torque between the two motors, to avoid overloading any single motor. Standard induction (asynchronous) motors have often been used but only in combination with mechanical gearboxes (reducers), required to reduce process speed to the correct level for mill pinions. The gearbox introduces added system complexity, capital cost, maintenance and energy cost due to mechanical losses. SYNCHRONOUS AND ASYNCHRONOUS MOTORS Elimination of the gearbox requires a motor designed to operate at a very low speed (rpm). Traditionally, mill motor requirements were best served by synchronous motors. The benefits of synchronous motors include- • Higher Efficiency (no conductor losses in rotor) • Very high power at low speed • Flexible Power factor (leading or lagging) • Constant speed (not load dependent) • More accurate speed control Synchronous motor cost is higher due to construction complexity, need for exciter and excitation panel, brushes, brush lifters. Figure 1 represents the equivalent circuit for a synchronous motor.Asynchronous motors, also known as squirrel cage induction motors, are singly excited, per Figure 2, the resulting equivalency circuit is less complex and only in need of a single voltage source.Commonly, a DC voltage supply is connected to the rotor (both physically and electrically) via brushes. The DC voltage enables the production of flux in a single direction. The brushes are connected to rings. The slip rings encircle the rotor but are insulated from the rotor. The slip rings are connected to a rotor winding known as a field winding. On large motors, brushless exciters are often used. A brushless exciter is a small AC generator whose field circuits are mounted on the stator and armature circuits are mounted on the rotor shaft. The exciter generator’s 3-phase output is rectified to DC by a 3-phase rectifier (mounted on the shaft) and fed into the main DC field circuit. It is possible to adjust the field current on the main machine by controlling the small DC field current of the exciter generator (located on the stator). [1] Brushless synchronous motors are often preferred over the traditional brush design but introduce additional complexity to motor construction in the form of additional windings and rectifiers comprising the excitation circuit. It stands to reason that because of the additional complexity, a synchronous motor will be higher in cost than an equally rated asynchronous induction machine."

Jan 1, 2015

By Toru H. Okabe

As part of a systematic study on the thermodynamic properties of complex nitrides, phase equilibria of the system Li-M-N (M Mg, AI, Ga) at 900 K were investigated. An attempt to determine the thermodynamic properties of complex nitrides was made by using the galvanic cell method, which utilizes LiMgN as an electrolyte under nitrogen atmosphere. The electromotive force (Emf) of ilie cell at temperatures between 800 and 1100 K was measured. Whilc the Emf of the cell at 900 K was measured to be 0.137 V, data discrepancies of ±0.03V were found. It was difficult to determine temperature dependence of ilie Emf. The Gibbs energy change for the reaction, 113 LbN (s) + 1/3 Mg3N2 (s) = LiMgN (s), at 900 K was determined to be tJ.Gor (LiMgN) -13.2 (±2.9) kJ/mol. Using thermodynamic information on ilie binary nitride from literature, the standard Gibbs energy of LiMgN was derived to be AGO f (LiMgN)= - 121 kJ at 900 K. The thermodynamic stability range of nitride was discussed by constructing isothermal chemical potential diagrams that provide a better understanding of ilie stability region of the LiMgN phase. The diagram was found to be in good agreement with the isoiliermal phase diagram determined by ilie alloy equilibration meiliod. Although the obtained data includes large uncertainties, the results provide a better understanding of the iliermodynamic stability of nitrides. The potential application of this complex nitride to nitrogen chemical sensors or a medium for controlling nitrogen potential is also shown.

Jan 1, 2003

By Paul E. Rosten

This paper describes some of the latest improvements that have been incorporated or planned by the Cleveland-Cliffs Iron Company to reduce operating costs and improve pellet quality. The Cleveland-Cliffs Iron Company operates and manages mining, beneficiation, and pelletizing operations in Michigan, Canada, and Western Australia. This paper deals with the grate-kiln pelletizing operations at Republic, Humboldt, Tilden, Empire, and Pioneer in Michigan, and the Adams and Sherman in Ontario, Canada. Table I characterizes .each operation in regard to location, ore type, pellet capacity and date that pellets were first produced. All of the operations with the exception of Pioneer and Tilden, utilize downdraft-two-pass grate cycles of drying followed by preheating. Pioneer utilizes an all-downdraft, three-pass grate cycle which consists of three drying zones followed by the preheat zone. The Pioneer and Tilden cycles have been described previously. (1) (2)(3) Tilden utilizes a three-pass grate cycle with a stage of updraft drying, followed by two downdraft drying stages. Recuperation systems which supply hot gases to a drying zone from second stage cooling were designed and furnished for Tilden I. Tilden II will be identical. Empire IV will also be furnished with a recuperation system. The Adams grate-kiln system was retrofitted with a recuperation system. This paper will summarize some of the efforts that are in effect or planned for grate-kiln pelletizing systems to (1) reduce operating and maintenance costs, (2) reduce energy requirements, (3) improve product quality, and (4) meet environmental standards.

Jan 1, 1977

By Ron Doucet

Industry today is now more than ever dependent on its assets and on the standard of maintenance. Changes in technology, environmental regulations, a continually improving focus on safety and global competitiveness has made maintenance a key activity in sustaining safe, financially viable and environmentally integral operations. Maintenance used to be looked upon as a cost centre with a sole focus of fixing equipment to attain high availability. Maintenance today affects all aspects of the business: safety, environmental integrity, energy efficiency, productivity, costs, and product quality. These new demands on the function of maintenance requires us to think vastly differently about what maintenance is all about, even to the point of contradicting old beliefs. In the following paragraphs we will examine some of the changed thinking that has evolved over the last 50 years. These new concepts will lay the foundation for the implementation of 21st century best practice maintenance.

May 1, 2003

By Lionel A. York

This paper outlines the type of water-bearing formations encountered in the Prairie Sediments and describes a method for effectively sealing these zones in order that shaft-sinking operations may be carried out with safety. Details are given of the procedure for carrying probe holes ahead of the shaft bottom. These probe or grout holes are employed for establishing a series of overlapping grout covers around the proposed shaft excavation to safeguard against large inflows of water during sinking. The pattern and length of grout covers cannot be standardized, and each cover needs to be specially designed to suit the varying ground conditions. In order to provide effective protection through the Prairie Sediments, the number of holes in any one cover would not be less than 8, and possibly as many as 64 would be required in certain zones. The length of covers would vary from 100 ft. to 250 ft. Emphasis is placed on the need for obtaining accurate geological and water information from exploratory holes, drilled in the shaft vicinity, in order to effectively plan all grout covers.

Jan 1, 1964

By Thor Pedersen

Elkem's technologies for the processing of waste materials, dusts, sludges and other residues, are based on the use of their Multi-Purpose Furnace as the primary processing component. The Multi-Purpose Furnace? is an electric slag resistance reduction furnace equipped with a hot media, Modular Freeze Lining and Elkem's proprietary, air tight electrode seals. The oil cooled? freeze lining allows specific heat fluxes 2 to 3 times higher than furnaces lined with conventional refractory. Reduction activities taking place within the furnace are free from the reoxidation potential of infiltrated air as Elkem's electrode seals are positively gas tight. Small quantities of highly concentrated off gas of controlled composition are produced to suit the requirements of downstream processing. The high electrical thermal efficiency achieved by generating heat within the slag itself, combined with the ability to operate at high melting rates and intense power density, makes the Multi-Purpose Furnace 9 an unique implement for the design of furnace products. These characteristics are utilized in the processing example cited, "Elkem's EAF Dust Processing Technology", which combines two proven technologies in an economically feasible system for the recovery of contained metal values from K061 wastes at the same time producing a disposable slag product. The portion of the example dealing with the condensation of zinc was prepared with the assistance of Imperial Smelting Processes, Limited of Bristol, England with whom Elkem has a non- exclusive license.

Jan 1, 1990

By Pengfu Tan

Electric arc furnace (EAF) dust from the steel industries is listed by the United Sates EPA as a hazardous waste under the regulations of the Resource Conservation and Recovery Act due to the presence of lead, cadmium and chromium. The disposal of the approximately 650,000 tons of EAF dust per year in the U.S. and Canada is an expensive and unresolved problem for the majority of steel companies. The Waelz process has been considered as the best process for treating EAF dust. A process model, combined thermodynamic modeling with heat transfer calculations, has been developed to simulate the chemical reactions, mass and heat transfer and heat balance in the kiln. The injection of air into the slag and the temperature profile along the kiln has been modeled. The effect of (CaO+MgO)/SiO2 on the solidus temperature of slag has been modeled also and discussed. Some optimizing results have been presented in this paper.

Jan 1, 2005