Search Documents

By J. M. Benson

Metal powder compaction offers unique advantages in the manufacture of net-shape components using techniques such as laser sintering, conventional press and sintering, metal injection moulding, direct rolling, direct forging, and hot isostatic pressing. If the output from the primary metal production process is in powder form, then considerable cost and energy savings can be realized by direct conversion to semi-finished or final shapes. This possibility exists for titanium and possibly also for Ta, Zr, Hf, and Nb metals. However, these attractive benefits are associated with some significant risks. The high surface-to-volume ratio of powder particles coupled with the reactive nature of these metals means that special care must be taken when handling them. Powder explosions are unfortunately still a regular occurrence internationally and these often result in serious injury and loss of life. Even seemingly 'safe' compounds such as sugar, flour, and grain can be extremely hazardous when handled or milled and dust clouds are produced. In addition, exposure to airborne particles can have adverse effects on the human body, especially when particles are inhaled on a regular basis. Furthermore, the medical consequences of these are not fully understood, especially in the case of nanoparticles. The impact is often not observed immediately and debilitating illnesses may emerge only years or decades later. As far as is known, there are no South African guidelines for handling of metal powders. This paper attempts to provide an awareness of the risks associated with metal powders (including those produced indirectly by other metalworking/finishing operations) as well as some guidelines for their safe handling, based on international best practices.

Jan 1, 2012

By T. Muldoon

Literature review and extensive field survey of line and check curtain materials and practices showed: ? Miners, in general, know how to set tight curtains, and do so when needed. ? The tradeoff is economic; tight ventilation is labor-intensive. Line and check curtain techniques found are catalogued and evaluated. A fieldworthy 10 ft extensible brattice to maintain a 10 ft setback was found in use in two mines on continuous miner faces. This technique was evaluated in the laboratory for leakage and methane control at the face. Significant results include: 1) Air leakage through a gap in the extensible curtain depends upon the ratio of the cross-sectional areas between entry and return as well as gap area; 2) Gap shape has no significant effect on methane concentrations at the face -increasing gap area diminishes ventilation effectivness; and 3) Substantial reductions of CH4 concentrations at the face were accomplished by brattice extensions with gaps of up to 5 ft2 in area. An "inby hook," inserted in the roof automatically to make possible the deployment of a longer (20 ft) brattice extension in the context of a remotely controlled miner, was tested in various roof types. Insertion of this design succeeded only in coal.

Jan 1, 1982

By R. S. Fowkes

A study was made by the Bureau of Mines of the penetration of selected granular materials in an unconfined state by wedge-shaped tools having dimensions comparable with the dimensions of the particles composing the materials. The output force for larger particles fluctuated radically. A custom-designed integrator was used to obtain work as a function of depth of penetration in the form of smooth curves. The influence of wedge angle, depth of penetration, penetration rate, entry angle, compaction state, and particle size on the force required and the work performed was ascertained. Empirical equations describing force and work as a function of penetration were obtained for each set of experiments.

Jan 1, 1973

By J. F. Smith

A series of studies of emissions from large coal-fired steam generators have included measurements of the concentrations of oxides of sulfur and oxides of notrogen. The sampling equipment, method of sampling, and analytical techniques used for processing of these samples are detailed. A method based on the precipitation of benzidine sulfate was developed for determining both SO3 and total oxides of sulfur in the presence of interfering acidic components in the stack gases. In addition, difficulties encountered with sampling and analytical techniques are also described.

Jan 1, 1968

By Wallace W. Key

Mineral raw materials produced in California, other States, and foreign countries were purchased for consumption in quantities valued at over $60 million at 800 of the 1,200 chemical plants operating in California Fn 1960, according to questionnaires completed by company officials. These and other data received from mineral consumers, producers, dealers, and Government agencies formed the basis for this the first of a series of reports designed to present the intricate features and relationships controlling mineral raw material supply and demand in California industries. The results of this study indicated certain changes in use patterns of minerals in chemical manufacturing; a shift in requirements from metals to nonmetals, from inorganics to organics, from natural to synthetic materials, and from distant to local sources of supply.

Jan 1, 1965

By Ranieri Corrêa Salazar

Essa contribuição técnica mostra a evolução do processo da Linha de Recozimento Contínuo de Chapas (LRCC#1) da Companhia Siderúrgica Nacional (CSN), na produção de laminados a frio sem revestimento para o segmento de mercado de tambores. A CSN vinha ao longo do tempo perdendo esse mercado devido principalmente a problemas de qualidade, como oxidação quando realizava a laminação de encruamento seca e, por outro lado quando processava o material com laminação de encruamento com óleo protetivo, ocorria no processo do cliente de cura a incompatibilidade com a tinta e vernizes nas aplicações mais críticas como acondicionamento alimentício, farmacêuticos e outros, cujos requisitos de qualidade rigorosos são exigidos contra qualquer tipo de contaminação. Desenvolveu-se um produto que associado ao controle de sua quantidade e a microgeometria da superfície da tira, resultou na lubricidade necessária para a continuidade operacional e atendeu aos requisitos de qualidade desejados.

Jul 30, 2018

At long last, mining is on the rebound in Minnesota?s Iron Range and the excitement is starting to show. The SME Minnesota Section?s annual meeting was once again held in the heart of Iron Range country, at the Duluth Entertainment and Conference Center on the Duluth waterfront. The conference boasted a record attendance of 475 people and its largest-ever trade show. Appearances by Governor Mark Dayton?s new Iron Range Resources & Rehabilitation Board (IRRRB) appointee, Tony Sertich, as well as a local Fox news crew (see clip on SME website [link: http://fox21online.com/news/duluth-mining-conference-breeds-optimism-tech-innovation]) made clear that a lot of eyes [ ] are on the industry as it dusts itself off from the 2008-2009 recession. While the early years of the 21st century were very good to the Iron Range, the global drop in commodities prices and production left many companies reeling and brought back bad memories of the collapse of the industry in the 1980s. However, two years of solid growth and a rebound to above pre-2008 production levels have let the Minnesota mining industry to relax a little and talk seriously about long-term growth and stability.

Jan 1, 2011

By Virginia T. McLemore, Devlon R. Shaver

Clinkers are the result of a seam of coal catching fire and burning the surrounding rocks. The fires caused the surrounding rocks to be baked at high temperatures, removing organic material and partially forming glass. These rocks become hard, orange, and brick like, forming clinker. The purpose of the study is to determine their potential to contain economic levels of critical minerals, including Rare Earth Elements. Some clinkers contain over 200 ppm total REE.

Feb 1, 2024

By John R. Shattuck

The Shasta and California Iron-ore deposits are 14 miles northeast of Redding, Shasta County, Calif.; and since 1907 have produced more than 300,000 short tons of exceptionally pure iron ore. Although some ore was mined and smelted from 1907 through the First. World War, most of it has been produced from 1942 through 1945 for use in making heavy ship ballast and concrete anchorages for mines. Irregular masses of magnetite, ranging from lumps of a few tons to pods containing about 25,000 tons, occur associated with skarn near the contact between the McCloud limestone and a younger granitic intrusive. Some of the deposits are low-grade, whereas others are nearly pure magnetite. Selective mining and hand sorting are necessary to produce a high-grade product. Investigation of these deposits by the Bureau of Mines included 2,910 feet of diamond drilling, some surface sampling of the principal mineralized zone and beneficiation tests. Resulting factual data are given in the body of this report.

Jan 1, 1948

By Francisco Grimaldo Zapata

Las estrategias son las únicas formas sostenibles de crear valor en las empresas. Sin embargo, los resultados en gestión determinaron algunos fracasos en su aplicación. En este sentido, es necesario plantear una gestión que permita mecanismos de reacción más rápidos ante los cambios, priorizando la capacidad de ejecución del la estratategia que la formulación de esta en sí misma. Por ello, el presente texto señala la aplicación de una nueva estrategia que busca el cambio de comportamiento en una organización antigua como es la unidad minera Cerro de Pasco. Las nuevas estrategias se aplican a la gestión de seguridad y medio ambiente, en el que se mejoran los procesos, se incrementa la productividad, se crea una política de prevención, y existe una mejor utilización de todos los recursos. Asimismo se reducen los costos y se le da más valor a la empresa para que pueda contrarrestar las fluctuaciones de los precios de los metales.

Sep 13, 2001

The AMIRA Code of Practice and Guidelines for Metal Accounting was developed in response to demand from a number of sponsor companies, including one major platinum producer. Since its publication in 2007, the Code has become widely accepted in the mining industry world-wide as a guide for best practice in metal accounting. With the changes in the structure of the platinum mining industry in South Africa over the last 10?15 years, in particular, the starting up of a number of small platinum producers who must have their concentrate smelted and the contained valuable metals refined by third parties, the need for metal accounting systems that are accurate and have an acceptable level of precision has become even more critical to the success of a platinum-producing operation. The current state of metal accounting in the industry is discussed, and possible areas for improved accounting and associated metallurgical efficiencies are identified.

Jan 1, 2013

A pilot scale AG milling campaign was conducted at the AngloAmerican Platinum pilot plant in South Africa. Different blends of hard:soft (silicate:chromite) and coarse:fine particles in the AG mill fresh feed were tested. The effects of multi-component feed on the pilot scale autogenous grinding are presented in this paper, and can be used as a guideline for multi-component feed blends for AG milling. Preliminary modelling and simulation for the multi-component AG mill model are also included.

Jan 1, 2012

By N. A. Eilertsen

The Aroostook manganese-bearing deposits lie within a rectangle 30 miles wide and 70 miles long. Over 40 different deposits have been discovered in this area, but they have not been mined because the ores are difficult to treat. In 1949, the Maple Mountain area was selected for detailed investigation by the Bureau of Mines, because study by the State of Maine and the Federal Geological Survey indicated that it was the most promising in Aroostook County for developing a large tonnage of reserves. Investigation by the Bureau of Mines disclosed that all of the reported deposits of the central district were located on the limbs of a syncline underlying a pear-shaped area of 283 acres between the crests of Maple Mountain and Hovey Mountain. The ore area has been outlined by trenching and drilling along three sides of the perimeter, while the remaining side is defined by a fault. The area has a length of 6,300 feet and a maximum width of 3,100 feet. Diamond-drill holes have intersected the deposit as deep as 1,550 feet below surface, but additional deep drilling would be required to determine the intensity of folding or warping at depth. The Maple Mountain-Hovey Mountain deposit lies in the slates of Ordovician age and is classified into three zones, of which the upper, averaging about 57 feet thick, is designated manganiferous purple and red slate. The central zone, also averaging about 57 feet thick and containing the highest manganese content, is manganiferous, banded hematite. The lower zone is manganiferous, interbedded hematitic and green slate with an average width of about 33 feet. Manganese minerals occur with hematite in all three units. Trenching on the northwestern slope of Hovey Mountain uncovered other disconnected deposits of manganiferous rocks of earlier age than the ore of the syncline. The general strike of these deposits, which range from 15 feet to 75 feet in thickness, is southwest a length of 5,000 feet. They dip steeply southeast. The ore of the syncline is predominantly deep, hematitic red, inclining to red-dish black, fine-grained, dense, and thinly laminated. It is hard and siliceous. Hematite has, in places, been altered to magnetite. Because of the fine-grained texture of the ore, the manganese-mineral constituents are difficult to determine. Of the manganese silicates present, braunite is the most readily identified. Manganese carbonates and oxides are found also.

Jan 1, 1952

By Myron W. Mellor

Our efforts at McNally, to find a better way to mechanically separate particles from liquid in a slurry have led to the development of two new centrifuges. The first unit utilizes a slotted opening screen as the filter media and retains all plus 200 Mesh and most of the 200 by 300 Mesh particles. The second unit is a solid bowl centrifuge with a novel method of removing the solids and delivers an effluent containing as little as 300 PPM solids in suspension. The first unit was designed to separate particles in the range of about 1 MM x 0 or smaller top size from the liquid slurry and produce solids having low surface moisture content, and a liquid concentrate containing a low percentage of solids. A prototype of this unit has been in the field undergoing tests for over two years. A few of these test results are shown in Tables I & 11. Testing has been mostly limited to the field of coal, how- ever this does not mean that the machine would accept only coal slurries. The machine has produced a dewatered product having as low as 5.5% surface moisture, and an effluent containing as low as 1.4% solids and handled slurries containing from 15 to 50% solids by weight.

Jan 1, 1975

By Gary M. Larwood

A study was conducted to determine the amount of transportation equipment required to move 1.2 billion tons of coal in 1985. The Federal Bureau of Mines has investigated a majority of the various practices associated with coal transportation and has gathered information on the regional origin-destination patterns, methods of movement, equipment stocks, rate structures, and operational capacities of the most important modes of coal haulage currently in use. Models employing this information were developed to establish the origin-destination pattern for 1985 coal shipments, estimate practical tonnage capacities for selected coal hauling rivers, develop modal shares for both unconstrained (by river capacity) and constrained cases, and present a range of coal transportation equipment requirements for given sets of constraints. Projected transportation shares for rail ranged from 63.7 to 72.3 percent, and for river, from 8.8 to 16.4 percent. Other coal transportation modes (truck, conveyor, Great Lakes, and tidewater) are expected to retain their historic shares of coal traffic. Equipment estimates were made for 1985 rail and water transportation based on 1973 average and best practice. Average practice estimates ranged from 675,000 to 710,000 hopper cars (100-ton) and 3,100 to 5,940 barges (1,400-ton equivalent). Best practice estimates ranged from 126,000 to 142,000 hopper cars and 1,750 to 3,450 barges. Full implementation of 1973 best practice by 1985 is unlikely.

Jan 1, 1976

By John D. Campbell

"IS YOUR MANAGEMENT CONTROLLOOP FUNCTIONINGMineral processors make use of hundreds of control circuits in their mills, process plants, smelters and refineries, to optimize throughput and recovery and minimize cost. This afternoon, I would like to discuss what is probably the weakest circuit in any mineral processing operation - the management control loop.In their recent book ""The Winning Streak"", Goldsmith and Clutter describe extensive research on unsuccessful companies. They conclude that ineffective control, which does not immediately identify the problems, is one of the main failings of unsuccessful companies.We will look at the three key components of control which, from the manager's point of view, ensure that the loop is complete. These three are:• measuring what's happening,• assessing its significance, Rnd• altering performance.If we compare management control to process control as shown in this first figure, ""We see that parameter sensing by the analyzer in a process circuit is analogous to performance monitoring by management in a responsibility centre. The analyzer senses temperature, pressure, flow, weight or some surrogate indicator such as colour to indicate ion concentration. For manage1nent, the performance to rnonitor is dependent upon the objectives of the responsibility centre, and the key factors which affect these objectives."

Jan 1, 1985

By W. J. C. Venter

The use of activated carbon to improve the selectivity in the separation of base metal minerals from bulk concentrates played an important role in the development of separation techniques employed at Tsumeb Corporation's Tsumeb and Kombat mines. In this paper the Kornbat mill flowsheet and metallurgical data are given with particular reference made to the separation techniques using activated carbon. The mine's historical background, geology and mining methods are described briefly.

Jan 1, 1973

By J. M. Wempen, M. K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote sensing technique capable of measuring centimeter-level surface displacement with high spatial resolution over large areas. Regular monitoring of subsidence due to underground mine development is one potential application of DInSAR, and in this study, the application of DInSAR for subsidence monitoring is evaluated for two mining regions in the mountain west of the United States. In general, DInSAR has potential to identify the shape and extent of subsidence; in some cases, magnitudes and rates of subsidence can be defined. Importantly, the effectiveness of DInSAR for subsidence monitoring depends on the radar band (wavelength), the subsidence rate and the time between image acquisitions, and the topographic and vegetative surface characteristics. INTRODUCTION Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote technique that can be used to measure small surface displacements. Under good conditions, centimeter-level displacements can be measured with subcentimeter accuracy (Buckley, 2000; Massonnet and Feigl, 1998). Additionally, DInSAR data have relatively high spatial and temporal resolutions. Pixels in Synthetic Aperture Radar (SAR) images can have a ground resolution as small as about 3 m, and images often include tens to hundreds of thousands of pixels and cover tens of kilometers. Regions are imaged regularly, and periods between images typically range from weeks to months. In DInSAR, phase measurements from two radar images acquired over the same region at different times are used to precisely measure relative distances (Rosen, 2014). Surface deformation, topography, and changes in the satellite position all contribute to differences in the length of the path that the radar wave travels in each image. SAR sensors use radar with relatively long wavelengths; L-band (24 cm wavelength), C-band (6 cm wavelength), and X-band (3 cm wavelength) radar are used most commonly. Because the wavelengths are long, small changes in the path length of the radar signal can be quantified by measuring the change in the phase of the radar signal between the images. In general, changes in the path length due to changes in the satellite position and topography are known or can be estimated, and centimeter-level changes in the path length due to deformation are measurable. This study evaluates the effectiveness of DInSAR for measuring subsidence in two mining regions in the mountain west of the United States. L-band data from the Advanced Land Observing Satellite (ALOS) and X-band data from the TerraSAR-X mission are evaluated. Imaging characteristics, including the radar band and the time between image acquisitions, are important for effective subsidence monitoring."

Jan 1, 2017

By Kerina Taylor

Due to their high amount of stored energy, explosives have been the cause of many serious injuries and fatalities over the last centuries. Despite safety advances and awareness in the last decades, injuries and fatalities continue to occur at mining operations due to blasting. According to the National Institute for Occupational Safety and Health, from 1978 to 2001, blasting incidents claimed 106 lives and were responsible for over 1000 injuries in mines in the US. The main causes of incidents found today are flyrock, blast area security and premature detonations. The concerted efforts of the mining and explosives industries and labour and government agencies have greatly improved the safety record of blasting in mines.

Jan 1, 2011

By M. Handley

The Witwatersrand Basin contains by far the most gold ever found, and has hosted mining from its discovery in 1886 to the present. For many years, South Africa was the world’s largest producerof gold, nearly all of which came from the Witwatersrand. Since 2000, South Africa has fallen back several positions because of declining gold output. There are many complex and varied reasons for this; however, declining gold resources in the Witwatersrand Basin are not one of them. As far as the author knows, there are no qualified estimates in the literature of gold remaining in the Witwatersrand Basin. This paper collects mining data from several sources and then, using elementary gold accounting and error analysis, attempts to estimate the amount of gold remaining in the Witwatersrand Basin. It includes gold underground in existing and defunct mines, in evaluated ore resources, and dumps. Compiled data from 1887 to 2019 shows that 50 200 t of gold were produced by Witwatersrand mines, while it is estimated that a further 48 100 t remainunderground, both within and outside of mine leases, a further 1 600 t on the surface in tailings,and an unknown amount in rock dumps. Nearly all of this gold will remain inaccessible with current mining methods, and major technical developments in mining will be necessary before any of the gold can be categorized as a code-compliant resource or reserve. To win this prize, the mining industry will have to rethink its approach to mining, both in old mining leases and in the unexploited ground. It will also have to find effective means of preventing gold theft and informal mining, which are on the rise.

Apr 5, 2023