Search Documents

By Anderson José Beber

O trabalho apresenta os resultados da aplicação de um novo oxidante moderado em uma grande torre de resfriamento utilizada em sistema de geração de energia de uma grande usina no sul do Brasil. Esta torre de refrigeração utiliza água de efluente tratado (tratamento terciário Esgoto doméstico) como fonte de reposição. Com aplicação desta nova tecnologia, houve uma melhoria tanto no controle microbiológico como na taxa de corrosão. Além disso, a planta foi capaz de aumentar o ciclo de concentração, resultando em economia de água, produtos químicos e menor geração de efluente, possibilitando economia superior a R$ 500.000/Ano, aplicando conceito de reuso.

Oct 30, 2017

By C. C. Stewart

Jim Walter Resources, Inc. operates four underground coal mines in Alabama. In 1986, during longwall recovery operations, sparks from a torch ignited methane that migrated onto the face after a roof fall. The fire quickly spread to the gob at the tailgate end of the longwall. The fire was successfully "area" sealed and mining operations resumed after five weeks. However, several problems were encountered during this process. This paper describes the events following the fire, methods used to control the situation, problems encountered, and steps taken to ensure preparedness for any future occurrences of this type.

Jan 1, 1993

By Keith A. Heasley

Numerous different instruments and techniques have been developed for the purpose of measuring rock stress and stress changes around excavations. The interpretation of the output from many of these instruments has often been problematic. This paper covers the research performed in attempting to analyze one particular stress measuring instrument called the Borehole Platened Flatjack (BPF) . The approach used in this analysis was to combine the analytical solution for the displacements around a borehole and the analytical solution for the bore- hole-platen interaction with the empirical stiffness behavior of the flatjack. The resulting model of the BPF response was then verified using measured laboratory data with very good results. In addition, techniques for applying the method to the field are briefly discussed. The major accomplishments of this comprehensive modeling and testing program are; 1) the establishment of the critical installation and site parameters of the hydraulic pressure cell and 2) the development of a systematic procedure for calibrating the cell based on the given values of these critical parameters.

Jan 1, 1989

By J. R. Goode

ABSTRACT Aurora Energy Ltd. is considering a 10,000 t/d process plant to produce 97 million lb (43,998,460 kg) of U3O8 over a 17-year project from uranium deposits in coastal Labrador. This paper summarizes the test work, mostly done by SGS Mineral Services in Lakefield, Ontario, and the economic studies supporting flowsheet selection. The proposed flowsheet includes semi-autogenous grinding (SAG) and ball milling, acid leaching using air/SO2 as an oxidant, and resin-in-pulp (RIP) extraction of uranium from the leached slurry. Other unit operations examined include ore sorting, heap leaching, liquid- solid separation, solvent extraction, and nanofiltration for eluate upgrading. We also review the extensive environmental test work and studies that were completed.

Jan 1, 2012

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselrnan Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo.

Jan 1, 1949

By J. F. Havard

Gypsum is a useful industrial mineral found abundantly on the earth's crust. It is inexpensive to mine and process, and its calcined products have a wide range of readily controllable properties such as strength, density and setting time. It has proven to be such a useful material indeed, that ten American companies, operating some 57 calcining plants in 25 states in 1958, produced or imported in that year a total of 13,649,000 tons of the crude mineral valued at $39,361,000, which they then converted into manufactured products with a value of $329,070,000. Gypsum (CaSO4.2H2O) is calcium sulfate with two molecules of combined water, which are responsible for most of its useful properties. It is closely associated in most deposits with anhydrite (CaSO4), which contains no combined water and has limited commercial value in the United States. Man has long recognized the useful qualities of gypsum. It was utilized by the Egyptians in the construction of the pyramids and, later, by the Romans for important structures. Many of the ancient peoples prized gypsum for artistic and ornamental purposes, carving statuary from alabaster and making casts with plaster. The tabular variety, selenite, was used for windows, and the light transmitted through these windows reminded people of light from the moon (selene), hence the name selenite. The use of gypsum continued through the Middle Ages and into modem times. Benjamin Franklin was a famed exponent of gypsum because he applied ground gypsum to clover fields in the form of large letters which later read, in the more luxuriant growth, "land plaster used here." Gypsum is still used as an effective conditioner for some soils, but in recent decades, particularly in North America and Europe, it has become much more important as a major material for the building industry. Description Gypsum and anhydrite are closely associated minerals. Gypsum is found in a number of forms: massive rock gypsum, alabaster, selenite, satin spar, and gypsite. Anhydrite is found as massive rock or as smaller bodies or isolated crystals included in gypsum. Massive Rock Gypsum comprises most of the commercial gypsum and occurs as a sedimentary rock, interbedded in most places with shale, limestone or dolomite. This rock is soft and crystalline. Its color is white or shades of gray, pink, yellow, brown or other colors. Alabaster is a pure, compact and fine-grained variety suitable for use in sculpture or turning into artistic forms; it may be white or selected for attractive coloration. Selenite is gypsum crystallized in flat, transparent, flexible foliated plates, found in clays or in surface vugs in gypsum. Satin Spar is a fine silky fibrous variety with the axes of the crystalline fibers perpendicular to the vein or joint in which it has formed. Gypsite is an earthy mixture of gypsum with clay and sand in secondary formations; it is sometimes useful as a soil conditioner and has been used in making base-coat plasters. Pure gypsum contains 20.9 pct combined water, 46.6 pct sulfur trioxide (SO3) and 32.5 pct lime (CaO). Standard specifications (American Society for Testing Materials Designation C 22-50) read that minimum purity for material to be called gypsum is 70 pct CaSO4.2H20. Most of the commercial gypsum is 85 to 95 pct pure as produced. Impurities in

Jan 1, 1960

Humankind's interest in measurement of human physical strength probably dates to the first humans. At that time, life was truly a struggle in which the fittest survived. To a great extent, fittest meant strongest. Interestingly, current interest in human physical strength in the workplace stems from 1970-1980s vintage research demonstrating that persons with adequate physical strength are less likely to be injured on physically demanding jobs. Survival in many modem workplaces may still be a case of survival of the strongest. There is, however, a flip side to this issue - that persons with limited strength are more likely to be injured on "hard" jobs. To address this problem, we can apply what we know about physical strength to job design. "Hard" jobs can be redesigned to be within the physical strength capability of most people. Since physical strength is important to these jobs, we must find ways to quantify it through testing. This publication concerns human physical strength testing. Its purpose is not to recommend any particular type of testing, but rather to describe the types of testing available and their uses. It is up to each individual user of strength testing to decide which testing technique is most appropriate for his or her particular application. This booklet discusses four types of strength testing: isometric, isoinertial, psychophysical, and isokinetic. Human Strength Before describing the different types of strength measurement, we must define the term "strength" and explain the concept of strength measurement. Strength is defined as the capacity to produce force or torque with voluntary muscle contraction. Maximum strength is defined as the capacity to produce force or torque with a maximum voluntary muscle contraction.(1,2) These definitions include some key words that must be explained. A voluntary muscle contraction is "voluntary." When a person's physical strength is measured, only the effort the person willingly puts forth at the time is measured. Thus, when we test a person's "maximum strength," we are not measuring his or her actual maximum, but some lesser value representing what he or she is comfortable expressing at the time with the existing equipment and environmental conditions. Interestingly, when researchers startled persons being tested (e.g., by setting off a starter's pistol behind them), they have found significant increases in measured strength.(3) It has been hypothesized that the lower strength displayed during normal testing provides a margin of safety against overloading and damaging muscle tissue. The test equipment and the tested person's familiarity with the process also influence the "voluntary" strength output. The interface between the tested person and the test equipment is particularly important. A poorly designed interface induces localized tissue pressures that vary from uncomfortable to painful. In this situation, testers are measuring voluntary discomfort tolerance - not strength. It is important for strength researchers to keep the "voluntary" nature of their data in mind when they are designing their equipment and protocols.

Jan 1, 1998

By Firth B. A

The flotation of fine coal (minus 0.5 mm) often requires the addition of an insoluble hydrocarbon collector to apparently promote the adhesion of coal particles to air bubbles. A series of experiments was conducted using a radiotracer and narrow size fractions of clean coal to determine the effect of particle size distribution, collector addition rate, desliming of feed and emuIisification of collector on the distribution of collector between the different size fractions. The concentration of collector per gram of each size fraction was found to be approximately proportional to (average particle size)-2 except if the collector was emulsified prior to addition, the dependence altered to approximately (average particle size)-1. Mechanistic consequences are discussed.

Jan 1, 1982

By I. Govender, M. C. Richter, N. Mangadoddy

"We present an analysis of trajectory and time averaged data of near gravitational material (NGM) representative coal tracer particles within a magnetite medium passing through a 100mm diameter hydrocyclone imaged with PEPT (positron emission particle tracking) at iThemba labs, Cape Town. The tracking of neutrally buoyant tracers as well as the other NGM allows an empirical study of the approximate dynamical behaviours of both the dense medium as well as the range (size and density) of particles around the separator’s cut size within a partially imaged volume of the cyclone body lying within the field of view of the detector. The study was commissioned as part of a CFD validation study using empirical data from a real-world lab-appropriate system in order to shed light on the inner workings of hydrocyclones and their separation mechanisms. We employ various optimisation and noise reduction techniques within the analysis and follow a detailed investigation of the velocity fields derived from the raw spatial positions with an emphasis on the velocity profile within the forced and free vortex zones. Challenges encountered with this high velocity particle tracking experiment within a highly attenuating environment are also discussed. Various important velocity distributions are shown and compared to theoretical predictions. The power law decay profile of the free vortex and radial velocity scaling with regards to the Froude number are reproduced in line with the static particle approach. INTRODUCTION Cyclones have long been a vital industrial tool for the separation of different classes of particles. These cyclonic separators (with either gas or liquid medium) operate by forcing the solids-bearing fluid at high pressure into a cylindrical vessel causing high tangential velocity fluid rotation as well as, in the case of an “open” (with exit channels open to the atmosphere) cyclone, a central vortex air column spanning from underflow to overflow exit. The fluid is forced to exit the cyclone at two locations, the spigot and the vortex finder, generating the underflow and overflow respectively. The body of the cyclone usually terminates in a conical shape to focus the underflow stream. This geometry and large incident fluid velocity force high density materials toward the wall of the vessel where they are most likely to move along and down the inside wall away from the inlet to exit via the underflow while lower density materials traverse the cyclone body closer to the central vortex and are buffeted by the upward-moving column towards the overflow exit. This separation mechanism is selective of density and size in an interplay between the centrifugal force due to the rotation of the fluid and a drag force acting on the particles."

Jan 1, 2018

By K. Vatterrodt

Thallium is not significantly removed from mining influenced water (MIW) through conventional treatment in hydroxide precipitation plants. We experimentally investigated modifications to hydroxide precipitation schemes to concurrently remove thallium. Our goal was to determine cost effective and efficient hydroxide precipitation process modifications for thallium removal. Strategies for removal targeted multiple mechanisms including sorption, co-precipitation and/or oxidation of monovalent thallium. Modifications were tested in batch and included oxidant evaluation and the role of manganese. Removal of thallium was enhanced by the addition of permanganate as well as oxygen by aeration. In addition, contact with retained solids and the initial manganese concentration played an important role in the extent of thallium removal observed. This paper reports on our findings and discusses the implications in the removal of thallium with minor modifications to the hydroxide precipitation process.

Feb 27, 2013

By William D. Hanson

Celestine (celestite) (SrSO4), the primary ore mineral of strontium, is present in the DeQueen Limestone Member of the Trinity Group (Lower Cretaceous) in Sevier, Howard, and Pike Counties, southwest Arkansas. Two mappable celestine beds have been identified. One bed is commonly 3-5 in. thick, but ranges up to 18 in. in thickness; the other bed is generally 2-3 in. thick. The beds are concordant within the DeQueen Limestone and were formed by precipitation from periodically restricted sea water. Reports concerning celestine date back to 1929, when Hugh D. Miser and A. H. Purdue mapped the geology of the DeQueen and Caddo Gap quadrangles. A small amount of celestine was produced in the early 1940s in Howard County. During 1941, the J. W. Hintze Company collected 1,500 pounds of celestine for testing purposes. In 1942 and 1943,750 test holes were drilled by the Bennett-Clark Company in Howard County. Afterward, approximately 90 tons of celestine was open-pit mined and shipped to Texas for processing. Since then, no mining of celestine in Arkansas has taken place.

Jan 1, 1999

By B. Dubreuil, J. -M. Lalancette, D. Lemieux

Arsenical bearing deposits are posing an increasing challenge for the mining industry. In particular, mineral processing of arsenical sulfidic ores for base and precious metals recovery tend to produce problematic arsenical tailings. This arsenic being present as sulphide or oxide, tends to dissolve, contaminating surface and underground waters. To meet the environmental regulations, it is often required to stabilize the arsenic in a more insoluble form. Dundee Sustainable Technologies has developed a new patented technology using vitrification of the arsenic oxide in an economical way, giving a stable solid, well below the environmental regulations upon leaching. This technology involves oxidation of As (III) to As (V), by using a low cost natural oxidizer and transformation of the produced arsenic oxide into calcium arsenate, which is not volatile at the melting temperature of the glass. This technology would be advantageously applied on most cases around the world where sulphide concentrates are oxidized in a fluidized bed or smelted.

Jan 1, 2014

The structure of a mine ventilation network (M.V.N.) can be represented graphically using either the mine plan (map) itself or a number of other types of diagrams. In the U.S., the two most common approaches are the line and the schematic diagrams (see Figures 1 and 2). The purpose of this paper is to introduce another type of diagram, called the canonical diagram (6). The method of M.V.N. representation which uses canonical diagrams is used extensively in Europe, and especially in Poland, where it was developed. The canonical diagram is a noncalibrated topological image of a ventilation system. It gives a simple representation of the ventilation network, allows for the classification of currents within it and enables rapid computer analysis and computation, as well as the representation of the results. It is especially useful in studying and controlling the air flow, and it may be a life saving tool in conducting rescue operations during and after mine fires.

Jan 1, 1986

By A. B. Cecala

An evaluation was recently performed on a district recirculation system at a trona mine in Granger, Wyoming. A 1.52m (5 ft) diameter, 37.3kw (50 hp) vane axial fan was installed in a crosscut between the intake and return airways and recirculated approximately 31.4 m'/sec (66,578 ft'/min) of air back into the intake. This amounted to a recirculation factor of approximately 20 pct of the return air. This air was part of the primary ventilation to three different continuous miner sections at operating distances of between 6l0m (2,000 ft) and 1,829m (6,000 ft) from the recirculation fan. The mine environment was constantly monitored for respirable dust, methane, and carbon monoxide in the operating sections and in the main intake and return entries. In addition, air samples were taken with and without the recirculation system during the evaluation and analyzed using gas chromatography. The results of this study showed only small increases in dust, while all other mine contaminants remained at such low levels that it was impossible to determine any relative changes from the recirculation system. Because of this, a brief SF. tracer gas analysis study was subsequently performed to more precisely determine an increase in a mine contaminant with the recirculation system.

Jan 1, 1991

By Thomas P. Mucho, David C. Oyler, Jim Pablic, Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to be abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1,000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

By M Zengerer

The Basil Cu/Co deposit comprises a 26.5 Mt Inferred Resource of copper and cobalt, grading 0.57?per cent Cu and 0.05 per cent Co. It lies in the Harts Range, Central Australia, within the Riddock Amphibolite of the Irindina Province. Analysis of drilling within the mineralised zone of the deposit determined a spatial association between pyrrhotite with high magnetic susceptibility and chalcopyrite, following a strong magnetic trend as determined from airborne geophysics. A study was commissioned to examine if geophysical inversion could predict the distribution of sulfide mineralisation based on pyrrhotite from drill hole intersections, as well as predicting further mineralisation at depth or in the vicinity of the deposit. Petrophysical and geostatistical analysis of drilling susceptibility and mineralisation provided a basis of property distribution inside the model. This was followed by 3D geological modelling of mineralisation based on domain kriging of drill hole susceptibility sensitivity testing of signal to source depth, and distribution was performed using 3D forward modelling. Stochastic inversion generated alternative 3D geological models, which were tested for behaviour and adherence to observed drilling data and geostatistical limitations using GeoModeller software. Predicted mineralisation distribution was compared with conventional geostatistical modelling and found to be in agreement in planar behaviour but exhibiting possibly isoclinally folded trends, with reliability increasing closer to the surface. Predictions of mineralisation at greater depth and beneath weaker anomalies were more diffuse due to small model cell size having limited influence on the signal at depth.The Blackbush uranium deposit comprises a 64.5 Mt Inferred Resource, grading 230 ppm U in the Pirie Basin south of Whyalla, South Australia. It directly overlies the radiogenic Samphire Granite and is considered a tertiary unconformity deposit. Sensitivity modelling was performed using high-resolution ground gravity to see if a deposit signature could be detected using gravity. This required 3D implicit modelling of the geology and mineralisation from drill hole data and characterisation of an associated physical property model using domain kriging in GeoModeller. Density models relied on exploiting an observed relationship between logged density and measured uranium oxide percentage. The residual gravity response of the background geology model identified the location of the uranium deposit. Stochastic inversion of the litho/property 3D model has refined the known distribution of uranium from drilling and provided structural insights into the deposit.These projects have become excellent case studies for exploiting the relationship between mineralisation and potential fields and for testing the applicability of using domain kriging of properties determined from drilling to build robust 3D geological models for stochastic geophysical inversion, leading to robust methods for exploration targeting and mineral deposit prediction.CITATION:Zengerer, M, 2014. Use of geostatistically-constrained potential field inversion and downhole drilling to predict distribution of sulfide and uranium mineralisation, in Proceedings Ninth International Mining Geology Conference 2014 , pp 281–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Peter Sylvén, Darwin Morales

Despite being crucial for the smelting process, furnace tapping using oxygen lances has not been considered an operation that brings value. Therefore, these important tools have not seen a significant change in over 100 years. Problems related to the use of oxygen lances include: • Inaccurate tool: causing damages shortening the life of the taphole refractories. • Safety: extended exposure to the operator in an unsafe area of the furnace. • Cost: high oxygen consumption & high lance consumption. • Time consuming and frustrating to connect one lance to another. This paper will suggest a very good solution; new concept thermal lances. We will show how these provide an outstanding performance for a more efficient, faster and cost-effective furnace tapping operation. These new lances are very accurate tools that enable the operator to perform a more controlled operation; resulting in longer taphole life, fewer repairs and less down-time.

Jan 1, 2016

By Jo Katembo, Patty Bwando, Patient K. Ilunga, Yves Kalubi, Emman Mulaj

"From 2010, the dolomite concentration in the ore fed to the Usoke Plant increased, resulting in a significant increase in the gangue acid consumption and Mg build-up in the circuit, and thus an increase in the Mg:Co ratio in the plant solutions. This affected the Co salt grade, reagent consumption, filtration and drying capacity. Efforts were put in place to minimise the acid consumption and consequently the Mg dissolution (such as use of pre-diluted acid), but the benefits were negligible. Various efforts were then initiated by CHEMAF to improve the cobalt plant productivity (quantity and quality) by process changes, dual precipitation and seed recycle. The positive results obtained in the laboratory were successfully implemented on plant scale. A change in the process from a single-stage precipitation with Na2CO3 to dual precipitation using a combination of Na2CO3 and NaOH improved the capacity of the Co salt filtration by 30%, the Co salt grade and drying capacity by 50%, and reduced the reagent consumption by 22%. Implementation of precipitate seed recycle increased Mg rejection by 40%, improving the Co salt grade from 20% to 25%, and yielding a further drop in reagent consumption. INTRODUCTION CHEMAF (Chemicals of Africa), a mining company located in Katanga province of Democratic Republic of Congo (DRC), has been operating since 2003. The Usoke hydrometallurgical plant treats the Cu-Co ore from the Etoile pit to produce Cu cathodes via a leach–solvent-extraction (SX)–electrowinning (EW) circuit and Co salt via a selective precipitation process. The plant was designed to treat run-of-mine (ROM) ore grading 6% Cu and 1.5% Co; but, in 2008, due to a decline in grades, a heavy-media separation (HMS) plant was commissioned to enrich the low-grade ROM (3.5% Cu and 0.5% Co) up to 8% Cu and 1% Co before feeding it to the hydrometallurgical plant. Co is recovered by precipitation of Fe and Al with limestone, followed by Co precipitation as Co carbonate using sodium carbonate (Na2CO3), also known as soda ash. 85% of the final effluent from cobalt precipitation is recycled back to the plant as process water; the balance, 15%, is bled out and compensated for by fresh water top up to control and retard the rate of sodium sulfate build up."

Jan 1, 2015

By F. Habashi

Chile is at present the largest copper and rhenium producer and was before World War I the largest nitrate producer. She is also an important producer of lithium carbonate and molybdenum oxide. An important event in the history of the country is the Pacific War of 1879-1883 in which she acquired the northern provinces initially belonged to Bolivia and Peru. In 1888 Chile annexed Easter Island. The Chilean mineral and cultural history is briefly reviewed together with the people who contributed to her development. The present report is the result of a number of academic and industrial visits to Chile during the period 1992 to 2009.

Jan 1, 2011

By WILLARD W. CUTLER

This bulletin reviews, in the light of recent experience, the use of production-decline curves in estimating the future production of oil from wells. It deals with the estimation of the reserves of recoverable oil in properties already producing or in those adjacent to them, takes cognizance of the physical laws governing expulsion of oil from oil sands, and shows how the production-decline curve can be made to utilize these laws in estimating reserves and rates of production. The valuation of oil properties should be based on the total amount of oil recoverable from a property by the methods in use, the rate of recovery, the cost of production, and the selling price. Numerous other curves besides those for reserves and rates of production may be formed from the production-decline curve and will present desired information in a convenient time-saving form. These curves also are described. Methods developed before the production-decline curve method was used are briefly discussed in order that the principles on which estimations of oil reserves are based may be made plain. The construction of curves and tables for estimating future production of individual wells and of average wells in most of the important oil districts of the United States is described and operating problems that may be solved by the use of production-decline curves are discussed. The bulletin does not deal with costs, oil prices, or the methods of evaluating oil properties. Many engineers have amply demonstrated the value of the production- decline curve method by forecasting within reasonable limits the production of many thousands of wells and tracts. The value of similar estimates depends however, on (1) the application of trustworthy methods; (2) the care and judgment of the estimator; and (3) the length and reliability of the records and the accuracy of ofher information used in estimating future production. When adequate records and information are available, experience has shown that It qualified engineer can forecast production far more accurately than has been deemed possible, except where the usual conditions governing the expulsion of oil from a sand have been radically changed by applying compressed air or by flooding with water, or, to a less degree, by using vacuum. In general, the production-decline curve method, though there are limits to its accuracy, is far more trustworthy than any other.

Jan 1, 1924