Search Documents

By Bhaskar B. Thapa

The design of the Caldecott 4th Bore, located along State Route 24 in Oakland, California, is based on the principles of the New Austrian Tunneling Method (NATM). Typical NATM initial support design practices used in Europe were adapted for this project to account for U.S. conditions and requirements, such as degree of experience with NATM construction, the prevailing contractual environment, and preferences for contractual simplicity. Key design features are: (1) support selection criteria based on ground behaviors and ground conditions; (2) a prescriptive design with allowance for support adjustments based on observations during construction; and (3) organization of support requirements into only four major support categories, while permitting some adjustment for variations in ground behaviors and conditions using a few subtypes and additional support measures.

By J. S. Miller

The Bureau of Mines developed methods for fragmenting oil shale formations with chemical explosives to prepare oil shale for in situ retorting and to evaluate the extent of fragmentation by various methods. A combination of three methods of explosive fracturing was used: (1) The displacement and detonation of a liquid chemical explosive in a natural fracture system; (2) the use of 60-pct dynamite to relieve stress conditions of the rock around the wellbore; and (3) the use of pelletized TNT in a series of wellbore shots to fragment the oil shale. An attempt was made to seal or grout around the fragmented oil shale by drilling 67 holes and displacing approximately 200 bbl of neat cement in the fracture system to aid in evaluating the fragmented zone, Seven methods were used to evaluate the fragmented zone. The primary evaluation method was the recording of seismic waves to delineate the fragmented zone with results based on arrival time, amplitude, and record quality. The data from the seismic measurements indicated the extensively fragmented zone was approximately 95 ft in diameter and 70 ft thick. Results of the remaining methods of evaluating fractures--including air-flow tests, coring of the expected fragmented zone, elevation measurements to indicate overburden crowning, and surveys with high-speed camera, impression packer, and down-hole camera--agreed with and supported the data from seismic measurements. Further field application of explosive fracturing and evaluation methods is needed to determine when a zone of oil shale is effectively fragmented for efficient in situ retorting.

Jan 1, 1973

By R. L. Marek

The number of persons fatally injured in the California petroleum industry, in 1932 was 24, a decrease of 6, or 20 percent from the number killed in 1931. The decrease in the number of fatalities occurring in 1932 caused the fatality curve of the California petroleum industry to reach its lowest point in 10 years. Changing conditions in the oil industry--reduced personnel, decreased active field development, and curtailed production--have undoubtedly caused a part of this decrease, but continued accident-prevention efforts by the industry have also contributed to the reduction in the number of fatalities for 1932. The Bureau of Mines has analyzed and reported annually the fatalities in the California petroleum industry for a period of 10 years. Figure 1 shows the trend of fatal accidents during that period.

Jan 1, 1933

By Edward A. Nowatzki

The purpose of this paper is to present an example of the application of a theoretically derived mathematical model for track-soil interaction to the evaluation of the mobility of large-scale mining equipment used in open pit operations. The model described by Karafiath and Nowatzki (1978) and presented in detail by Karafiath (1978) was used to predict the performance characteristics of four different bucket wheel excavators (BWEs) on rwo types of copper mill tailings at various moisture conditions. The BWEs considered In the analyses are two-and three-tracked continuous excavators. Most have boom-mounted rotating buckets and swinging side- or rear-discharge conveyors. The analyses were performed at the request of Dames and Moore for the Kennecott Corporation's proposed remining of selected tailings deposits at the McGill, Nevada, concentrator. The objectives of the analyses were to determine whether BWEs would have sufficient mobility In the tailings deposit to achieve satisfactory production rates, and TO compare the predicted performance of the various BWEs evaluated. Good qualitative agreement was obtained between the results of the theoretical analyses performed for the McGil1 operation and the actual performance of BWEs in two South African gold mine tailings impoundments.

Jan 1, 1980

By Hemendra N. Kalia

Several attempts have been made in the past sixty or so years to commerciliaze the vast oil shale deposits of the United States of America. However, the industry has yet to become viable and economic. To date, it has not been possible to produce oil from the oil shales at a competitive price when compared to the oil produced from oilfields by conventional methods. However, the development work has been quite fruitful in furthering the art of thick bed mining and technology of in situ retorting. The in situ method has the potential of recovering oil from thick beds and the resource recovery potential is much greater than that from underground mining and surface retorting. In situ methods require that the shales/ marlstones be fragmented ' in place to induce adequate porosity and permeability to allow in situ' heating of the fragmented shales. This can be accomplished by using explosives. However, it has been found that the existing blasting systems, though very efficient, are somewhat lacking. The explosive become insensitive when shot in multiple vertical decks. They can also become insensitive when spaced horizontally at close proximity to other charges. Also, since the blasting is done in a very limited free face, this limits the delay time that can be allowed between charges. Consequently it is not always possible to predict the performance of the blasting system on a routine basis. Furthermore, since it is not possible to undertake secodary blasting, it is imperative that the blast design function properly. Recent, successful retorting by Occidental Petroleum Company of retorts seven and eight suggests that some of these problems may have been overcome. This paper addresses some aspects of in situ retorting and problems those have impeded the development of a viable oil shale industry in the U.S.A.

Jan 1, 1983

By M. Botz

Anatolia Minerals Development Limited (AMDL) is constructing the Çöpler Gold Project in eastern Turkey and commenced mining in the fourth quarter of 2009 with gold production scheduled to begin in the fourth quarter of 2010. The project is a 15,500 tonnes/day oxide heap leach with three-stage crushing, agglomeration, carbon adsorption and electrowinning for final metal recovery. Leach solution copper levels are expected to be relatively low during the first two years of production but will increase in later years due to higher copper content in the mined and processed ore. Over the mine life approximately 40 million tones of ore will be placed on the leach pad, which will contain about 35,000 tonnes of copper. Metallurgical testing indicates copper extraction will vary by ore type and, if controls are not implemented, may lead to copper levels exceeding 1,000 mg/L in pregnant solution. High copper levels in leach solution have the deleterious effect of increasing cyanide consumption and potentially overwhelming the ability of the carbon circuit to effectively adsorb the principal economic metals, which in this case are gold and silver. Using data obtained from laboratory leach column testwork, the heap leach facility was modeled using METSIM process simulation software to estimate the build-up of copper in leach solution over the mine life. Laboratory testwork was also performed to evaluate process conditions for treating a portion of pregnant leach solution via sulfide addition to precipitate saleable copper as copper sulfide (Cu2S).

Jan 1, 2011

By Sherwin F. Kelly

With the progressive exhaustion of ore deposits easily discovered by surface prospecting, the attention of scientists is being turned more and more to the employment of mechanical means for the location of ore bodies whose outcrops are not visible. The dip needle, the Eotvos Torsion balance, and various methods of electrical prospecting are illustrative of the modem tendency. Interest in the possibility of applying electricity to the solution of many of the prospector's problems dates much farther back than is usually realized. The first person to notice an abnormal intensity of electrical activity in the region of certain ore bodies was an Englishman, R. W. Fox, who experimented on the Cornwall copper and tin veins about 1830. Dr. Barus, in the United States, carried the early experiments a step further in his work on the deposits of Eureka, Nevada, about 1880. He made the very definite suggestion that the phenomena noticed would be of material aid to the prospector. Not until Professor Schlumberger, of the Ecole des Mines, Paris, took up the matter, shortly before the war, was any definite effort made to put electrical prospecting on a commercial basis. His work resulted in the establishment of sound principles and practicable field technique, for two distinct methods of prospecting.

Jan 1, 1924

By S. J. Schatzel

In order to better understand the effects of longwall mining on the methane reservoir overlying the panel, the National Institute for Occupational Safety and Health/Pittsburgh Research Laboratory (NIOSH/PRL) designed and implemented a vertical borehole monitoring experiment (BME) on an active longwall panel. The mine operates in the Pittsburgh Coalbed in Greene County, Pennsylvania. The BME site was located away from either end of the panel to avoid mechanical influences caused by the draping of overburden in this region and was positioned at the same distance from the tailgate gateroad as the mine?s gob gas venthole sites. The borehole drilling depths and monitoring intervals were chosen to address a different stratigraphic zone in each of the three planned holes. The monitoring boreholes were positioned perpendicular to face advance using a close spacing pattern of about 15 m (50 ft) between collars. Boreholes were instrumented downhole and on the surface for various measurements. It was observed from the field data that the gob gas venthole fracture network formed 24-46 m (80-150 ft) ahead of the mining face. Overburden permeability?s within the same test zones increased 100 to 500 times following undermining. The borehole test interval within the fractured rock responded to overburden gas pressure while the test interval in the caved zone responded to mine ventilation conditions. Eight months after the boreholes were undermined, slug testing indicated permeabilities had increased further in the fractured rock zone. Measurements of surface movement indicate that the permeability development observed in the boreholes is a product of vertical subsidence without lateral movement within the tensional rock mechanics zone on a supercritical longwall panel. Results from this study suggest that maximum permeability in the longwall panel overburden is achieved 58 to 190 m (190 to 620 ft) behind the longwall following maximum compaction of the overburden.

Jan 1, 2009

Quartz, adularia and clay minerals from low-sulfidation epithermal veins at Hishikari were analyzed for their oxygen and hydrogen stable isotope compositions to establish the source of paleohydrothermal waters. Positive correlation between Au-Ag and adularia: quartz ratio, the presence of quartz pseudomorphs of bladed calcite, and Au-bearing smectite and vermiculite is indicative, but not definitive, evidence for the control of boiling on ore mineralization. Oxygen isotope equilibrium temperatures between quartz and adularia are about 220¦C and average homogenization temperatures of fluid inclusions vary between 190 to 210¦C. The calculated d18OH2O and dDH2O values (from quartz, adularia and early smectite) are consistent with paleohydrothermal fluids that were a mixture of magmatic and meteoric waters, or alternatively, the values could derive from heated meteoric water which had undergone isotope exchange during circulation through basement rock. Overall, d18Oqtz values in veins increase toward the north, most likely reflecting palaeo-fluid flow (source).

Jan 1, 2001

By G. E. McClelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores, wastes, and tailings. This technology has been adopted on a broad scale by the precious-metals-processing industry. This report presents information on five commercial operations that have benefited from agglomeration technology and that represent a cross section of current heap leaching practice. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1983

The inquiry into the explosion at the Moura No. 2 Mine in August 1994 recommended -?Emergency procedures should be exercised at each mine on a systematic basis, the minimum requirement being on an annual basis for each mine.? (Windridge et al. 1996). In December 1996 the ?Approved Standard for the Conduct of Emergency Procedures Exercises? was published and has been subsequently revised (Queensland Department of Mines and Energy Safety and Health Division 1999). This document provided guidelines for conducting mine site emergency exercises as well as the requirement for a test of state-wide emergency response by holding a Level 1 Mine Emergency Exercise at one mine on an annual basis. From 1998 to date (January 2008) ten Level 1 Mine Emergency Exercises have been held in Queensland, Australia. This paper discusses each of the exercises conducted to date as well as the logistics, scenario preparation, planning and organising required to conduct emergency exercises at this level.

Jan 1, 2009

By C. D. Hunter, I. B. Browning, N. W. Shiarella

During the year 1936 improvement in the oil industry in Kentucky continued at about the same rate as shown by that of the year 1935 over the year 1934. The development of several new pools in western Kentucky and the increase in the application of repressuring methods to the old fields of eastern and to a lesser extent of western Kentucky increased the total production to 5,481,227 bbl., as compared to 5,175,054 produced in 1935. The principle sources of this increased production are the Livermore field and the new Bates Knob field in McLean County, in western Kentucky, and the result of repressuring operations in the " Corniferous" pools of Lee, Powell, Wolfe, Morgan and Estill Counties and the "Weir" sand (of Mississippian age) fields of Magoffin, Lawrence and Johnson Counties in northeastern Kentucky. The last named fields have a producing sand especially adaptable to these methods. Drilling No new fields were opened in eastern Kentucky during the year. All new drilling was codned to pressure wells and new oil wells to complete patterns around the intake wells. Owing to the relatively low "initial" or flush production of the wells in this section—even though the ultimate recovery per acre is as large—higher prices for crude will have to prevail before extensive search for new fields is begun; as in northwestern Kentucky, where active exploratory work has been carried on as in the several preceding years, resulting in numerous new and prolific, although comparatively small fields. In this section approximately 500 new oil wells drilled in the Owensboro field, embracing several pools in Ohio, Hancock, Daviess, McLean, Henderson, Webster and Nuhlenberg Counties in the northwestern part of the state. The total oil production for this field during 1936 exceeded by many thousand barrels the 2,821,722 bbl. produced in 1935. In these fields the producing sands range from the middle Missis-

Jan 1, 1937

By Claudio Acuña, Sergio Romo, Gerardo Fuentes

The leaching kinetics of a zinc concentrate in autoclave reactors were studied. A sample of concentrate from Bolivia, with typical mineralogical characteristics of the Andes region, was used. A concentrate containing 49% zinc and 145 ppm of silver from Minera Viacha was characterized chemically and mineralogically (atomic absorption, X-ray diffraction, and SEM microscopy) and tested in bench scale reactors. Two types of autoclave batch reactors were used at 40 bars of oxygen pressure and three levels of temperature (150°C, 200°C and 250°C). The solid to solution leaching ratio was 1:10 (10% sulphuric acid concentration). The effect of the particle size of the concentrate on the leaching kinetics was studied (P80: 145 and 45 µm). Iron from the leaching solution was removed by precipitation by increasing the pH in order to generate a clean solution for zinc electrowinning. The zinc solution was used to evaluate the feasibility of cathode production at the laboratory scale. Zinc extractions with higher liberation (P80 = 45 µm) reached up to 98%. Ground concentrate with finer sizes resulted in agglomeration and the use of dispersing agents did not improve slurry mixing. The leaching solution contained 55 g/L zinc and 7 g/L iron; it was purified by precipitating iron. The precipitation was evaluated using sodium hydroxide and ammonium hydroxide. In the first case, a colloidal suspension of ferric salts was formed while in the second case, different iron compounds were precipitated. The precipitate obtained with ammonium hydroxide had better filtering properties. Electrowinning was carried out using two types of cathodes (stainless steel and aluminium) and solutions purified with ammonium hydroxide. Zinc cathodes formed on stainless steel presented a better physical quality than those formed on aluminium.

Jan 1, 2015

By K. C. Tran

This paper reviews the advancement of measurement technologies for the control of raw materials processes in the basic industries. The combination of digital technology and on line spectroscopy enables the development of intelligent instruments for composition and particle size analyses in real- time high- frequency control conditions. In many industries, the applications result in productivity improvement and energy savings. Plant specific examples include operating experience and benefits realized in sorting, blending and beneficiation processes. Instruments of the future not only measure specific parameters of the process and monitor its own health combined with self-corrective mechanics but also acts with intelligence to effect the quality of the process or regulate the primary apparatus.

Jan 1, 2001

By Lauri Gregg

The implementation of Energy Management within the global mining industry has advanced significantly during the past 20 years. Consequently, the industry?s knowledge of energy efficiency improvement opportunities, more energy efficient technologies, renewable energy technologies, energy procurement practices, and most importantly, practical approaches for integrating the energy management best practices into business processes and operational procedures has improved greatly. Based on 25 years of experience leading the management of energy in mining operations and the Canadian mining community, the author discusses the key building blocks in the evolution toward becoming an energy efficient mining facility. Sustainable energy management depends on the internalization of the behaviors related to the effective energy use by a mining organization. The paper outlines the typical business drivers that stimulate top management commitment to allocate the resources necessary for this to happen. It also explores the barriers that mining companies must overcome to maintain the commitment. Additionally, it will advocate the need for the application of the principles of organizational change management as part of the energy management implementation process. The question regarding how energy management can be made to happen in a way that is practical for an established organization is answered by providing the details of the framework for energy management, the methodology for controlling energy use, and the roadmap for integrating energy as a key business parameter and production process input variable. An Energy Management System standard developed within the Mining Association of Canada?s ( MAC ) Towards Sustainable Mining ( TSM ) initiative has played an important role in increasing the capacity of the Canadian mining industry to manage energy. The impact of the application the MAC TSM Energy/GHG Management Protocol by Canadian mining companies will be discussed. In June of 2011, the international ISO 50001 Energy Management Systems standard was finalized and published for use. The structure of ISO 50001 will be outlined along with its applicability to the mining industry. Opportunities for practically improving mining energy performance along with the most appropriate current new technologies will be identified. A brief discussion of case studies will be included that demonstrates the successful implementation of Energy Conservation Measures ( EAC?s ) and economic benefits. In conclusion, thoughts on important areas of research and development related to increasing mining energy efficiency will be provided.

Aug 1, 2013

By Donald W. Mitchell

Studies were made in the Bureau of Mines Experimental coal mine to evaluate the effectiveness of a few extinguishing agents and techniques for controlling a fire on a simulated mining machine. The investigation showed that water containing an alkali-metal salt or a surface-active (wetting) agent was more effective than water alone. For close attack, fog applications was the most effective technique studied; high rates of agent application controlled the fire more quickly than low rates. The ability to control the fire increased as the distance of attack decreased. Dry powders controlled the fire when applied by shovel but not when applied airborne by rock-dust distributor or by hand fire extinguishers. Dry alkali-metal salt powders (potassium and sodium bicarbonates and sodium tetraborate) quenched the fire more readily than limestone dust. In each instance the finer powder, the greater its effectiveness. In an open ventilated entry, smoke and hot gases backed against the air currents. An airspeed of 230 feet per minute was required to permit approach to within 10 feet of the fire. At lower airspeeds, approach could be made by extending the brattice across the bottom two-thirds of the entry, by pushing the smoke ahead with water sprays, or by discharging dust from a rock-dust distributor. In a dead-end entry, the fire was approached to within 30 feet by coursing fresh air along an airtight line brattice; however, it was safer, easier, and less time-consuming to attack the fire from a fresh-air base 100 feet away with a solid stream or by high-expansion foam; the latter method was more effective.

Jan 1, 1961

By F. H. Mertens

The costs of an open-pit operation can be classified according to the following hierarchy : -overall cost of production (per ton of ore) -costs of basic operations and functions -costs of auxiliary operations -costs of machines and equipment -maintenance costs. Production cost is a measure of the open-pit mine performance and should be the final target of the management control. It is also a measure of the share of the mine in the processing stages.

Jan 1, 1990

By D. Harrington

Along with other phases of mining , the ventilation of metal mines has been affected by the business depression of 1930. As might be expected , some of the results are favorable , and some are distinctly disadvantageous to progress . Probably the worst effect of the recession of mining activity is that , as usual , one of the first departments of almost any industrial establishment ( and this is especially true of mining ) to be curtailed is that which concerns what might be called welfare work , such as safety , health , etc. , and ventilation : in consequence , a number of men who were employed mainly on ventilation work in metal mines are now out of employment and their former duties either are being handled by others as only part of a crowded routine or are being allowed to lapse . On the bright side of the picture is the following paragraph from a letter by the ventilation and sarety engineer of the United Verde Copper Co. , Jerome , Ariz . , indicating that money and effort expended on ventilation during " flush " times give results which aid in money savings when depression comes : The desirability of absolute control over the ventilation system has again been demonstrated at this mine . Under full operation we have been using approximately 500 hp . to drive our big fan . Under curtailed operations we naturally do not require as much air , so by sending the air only where needed and airing out all other places periodically to keep timber , etc. , in good condition we have been able to economize in the quantity of air required . The fan speed has been reduced and the power dropped to 300 hp . , thus effecting a material saving in the power bill , and still maintaining an efficient ventilating system . "

Jul 1, 1931

By Junfeng Shen

Geosynthetic clay liner (GCL) is a kind of waterproofing material used widely in engineering. The waterproof mechanism is understood in terms of bentonite particles becoming a water-obstructcolloid layer after they absorb water and swell. The swell stress, however, has not been determined directly till now. In our experiment, the swell stresses of the GCL under saturated and water absorbing conditions are measured directly using a custom-made instrument. The results show that (1) the instrument designed by the authors performed satisfactorily and the test results are reproducible; and, (2) The trend line of swell stress variation with time can be divided into three segments. The first segment is characterized by a quick increase of the swell force in the first 0?50 hours. The swell stress increases by 7.00×10-4?1.00×10-3 Mpa / hour. The second segment shows a slow increase of the swell stress during the 50?1730 hours. The swell force increases by 7.54×10-6?2.02×10-5Mpa / hour. The third segment is characterized by little variation in the swell stress after 1730 hours. In this segment, the average value of the swell stress measurements is 0.0719Mpa and the maximum value is 0.0729Mpa. It is suggested that the swell stress is mainly raised by water entering the pores among montmorillonite particles and the interstitial layers in individual montmorillonite crystals, leading to an increase in volume and manifested as a stress on the surrounding materials.

Jan 1, 2006

By Frank E. Cash

Although during the past 10 years Alabama has attained an enviable position by its coal-mine accident experience and, like most of the other coal-mining States, has made progress in the safer operation of coal mines, there is still room for improvement, which can be realized only by still greater efforts on the part of employees and employers. From 1993, when accidents were first recorded by the Alabama State Mine Inspection Department, to 1934, inclusive, 3,451 men lost their lives in the production of 569,722,676 tons of coal. The primary purpose of this report is to bring to the attention of the mining industry in Alabama end elsewhere statistics of fatal accidents for 1931-34, with the hope that a study of the causes may lead to reduction of similar accidents in the future.

Jan 1, 1936