Search Documents

By Wenjun Duan, Zongliang Zuo, Qingbo Yu, Qin Qin, Junxiang Liu

Moving bed has been widely used in the field of heat and mass transfer and reaction between solid particles and gas. In order to enhance the heat exchange coefficient, there will be tube banks inserted in the moving bed. In the process of drying ammoniates particles or heat recovery from high-temperature particles with moving bed, the particles flow behavior around the tube banks is significant. In this paper, the particles flow behavior around the tube banks is investigated, and all the results can provide guidance for the design and operation of a moving bed.

Jan 1, 2016

By Yongquan Zhu, Zhengguo Zhu, Zhichun Liu, Chao Kong, Xinqiang Gao

"The aim of the study is to have a good understanding of the change in the seepage field during and after the tunnel excavation in weathering alteration rock. Field tests are used to monitor the changes of the water table and the numerical model is used to analysis the influence of the seepage filed with different operation conditions during and after the tunnel excavation. Results indicate that the depth, diameter and pumpage of precipitation well are the main factors that have a great influence on the drainage effect. Results also indicate that different operation conditions had various effects on the decrease in water yield during tunnel construction and the recovery in groundwater level after construction.INTRODUCTIONAs a potential disease during tunnel construction, Gushing water not only affected construction schedule, increased construction cost, as well as affected tunnel stability and safety during operation, but also decreased ground-water level. What’s more, the fall of water table caused by gushing water in tunnel would have influenced surrounding residents’ living water, agricultural water and ecological environment around tunnel. In recent years, enough emphasis has been paid to the influence on environment due to the construction of tunnel as a result of the reinforcement of people’s environmental protection awareness.As a result of water collection and drainage after excavation, groundwater was discharged into the tunnel, which caused a loss of water resources in the adjacent mountain mass. Furthermore, during tunnel operation, it was difficult for groundwater level to resume its original condition, which caused a bad ecological environment, because drainage system during tunnel construction destroyed its original hydrologic dynamic balance.In order to study whether decreased groundwater level resulting from tunnel construction could be restored during operation to its original condition, this paper gave a field monitoring on tunnel displacement during construction and simultaneously, generalized model of regional hydrogeology was created according to field hydrogeology to carry out a calculation of stable seepage flow and draw comparisons between recovery conditions of various water levels."

Jan 1, 2015

By N. W. Hendry

ABSTRACT Exploration by geophysical methods and diamond drilling of an occurrence of chrysotile asbestos, located ten miles east of Matheson, Ontario, was commenced on March 25th, 1949, by the Canadian Johns-Manville Company, Limited. The asbestos is associated with a narrow sill-like body of basic and ultrabasic rocks which strikes northwesterly across portions of Munro and Beatty townships. To date, asbestos zones of commercial interest, many hundreds of feet in length, width, and depth, have been outlined by diamond drilling along a 2-mile length of serpentine. The fractures occupied by the asbestos veins are closely associated with the regional faulting in the area. The mining of the first occurrence, or A orebody, will be by open-pit methods. Milling will commence at a rate of 50 tons an hour. INTRODUCTION OCCURRENCES of chrysotile asbestos in Munro township have been known at least since 1914 and references to them appear in reports published by the Ontario Department of Mines in 1915 (1) and 1919 (2). J. G. Ross (3) in his excellent publication on Chrysotile Asbestos in Canada, mentions an occurrence in Munro township. The area was first mapped in detail by J. Satterly, of the Ontario Department of Mines, in 1944, and brief mention is made of chrysotile asbestos in Satterly's preliminary report (4), which was published the following year.

Jan 1, 1951

Response of a mineral to anionic and cationic flotation reagentsvaries with the nature of the mineral and the particle size. A ruleis deduced for the selection of the correct type of reagent, which leads to a simple method of testing ores to determine the possibility of separating the constituents by flotation.

Jan 1, 1963

By T Ladinig

Raise caving is a novel cave mining method, which has been proposed for mass mining at increasing mining depths in LKAB operations. The method makes use of the raise mining technology and an active stress management approach. For the implementation the method is split into two phases, namely a de-stressing phase and a production phase. In the de-stressing phase, a slot-pillar system is established. The purpose of slots is to provide stress shadows and the purpose of the large pillars is to control stress and seismicity. The production phase follows after the de-stressing phase. Required infrastructure in the production phase is developed delayed in stress shadows and bulk extraction takes place in de-stressed zones. Eventually the pillars crush and they are extracted in the production phase. A comprehensive research and development program has been launched to develop the raise caving method towards implementation. As part of this program a full-scale test site of raise caving will be conducted as well as raise caving operations are planned for depth extensions in LKAB mines. This paper discusses the design of raise caving operations in practice at the LKAB mines. In particular, the purpose of the paper is to focus on requirements for the development and design of a raise caving operation. The development of raise caving is discussed from a systems engineering perspective as well as from a management perspective. The functional requirements in the destressing and production phase are outlined and discussed in the paper. The discussion is on basis of the main elements of the raise caving system, such as slots, stopes, pillars and infrastructure. Critical rock engineering design requirements in the de-stressing and production phase are highlighted and dependencies between individual main elements are identified. The analyses show that pillars are especially important for the success of the mining method. Overall, the analyses show that raise caving is a complex system and that its development demands a multidisciplinary approach.

Mar 29, 2023

By Michael S. Contratto, Dave Marshall, Tom Brodersen

The European Union (EU) completed a new directive 2002/44/EC1 called the Physical Agents Directive (PAD) that establishes action and limit values for hand-arm and whole body vibrations. The directive specifies that: “…workers shall not be exposed above the exposure ‘limit value’.” 1 and “…once the exposure action values … are exceeded, the employer shall establish and implement a programme of technical and/or organisational measures intended to reduce to a minimum exposure to mechanical vibration and the attendant risks…” 1 The PAD limit value is effective for new machines starting July 6, 2007 and for used machines by at least July 6, 2010. These requirements apply to the users of machines, but machine manufacturers will be challenged to provide machines and information to help the users comply with the directive. Caterpillar manufactures machines with the goal of enabling our customers to comply with all regulations dealing with health and safety. Caterpillar designs all of our machines to provide a safe, comfortable and productive work environment. This study was to determine if seat suspensions could provide a reduction in the vibration environment experienced by operators of Caterpillar mid sized (<50,000KG) Track Type Tractors Methods Seat manufacturers were asked to provide seat suspensions that provide improved isolation over and above current seat suspension. Each supplier was provided with ride profiles and was asked to demonstrate the vibration reduction on a shaker table. Two suppliers provided suspensions that were compared with the current seat suspension in a field study. Three full factorial experiments were conducted. The first experiment was to evaluate overall suspension performance for four operations. The second experiment was to determine the benefit of the adjustable vertical damper at three different levels and the third experiment was to determine the effect of the fore/aft and side/side isolators. Six operators were used for the study. Acceleration was measured at the seat base and at the operator seat pad. Both the transfer function and the ISO 2631 RMS ride values were used to determine the seat suspension’s effectiveness of isolating the operator from vibration. A structured questionnaire was used to determine the operators’ subjective assessment of the seat suspensions. Results There was significant operator-to-operator variability in the vertical direction (>35%), however there was little variability in the fore/aft and side/side direction based on seat base

Jan 6, 2006

By David C. Grant

A laboratory technique for simulating in-situ uranium mining was developed and used to determine the effects of leaching variables on permeability, uranium recovery, leach solution interaction with the ore-aquifer environment, and post-leach chemical leakage. In particular, ammonium bicarbonate, the commonly-used leach solution, was examined in great detail. Agitation leach tests were conducted to examine the effect on ammonium sorption and desorption of clay content, solution and clay ammonium levels, pH, and the type and concentration of other anions and cations in solution. Initial column tests were performed to determine the degree of ore-aquifer interaction that could be expected for various leach solutions; sulfuric acid, and ammonium, sodium, and potassium bi-carbonates. Subsequent tests examined various methods to restore the ores by lowering the post-leach chemical leakage. The restoration tests examined the use of reducing agents (e.g., ammonium bisulfite, sodium bisulfite; and sodium sulfite), ore blocking and stabilizing agents (e.g., sodium silicate, aluminum chloride, and magnesium-calcium salt).and ammonium displacement agents (e.g., aluminum chloride and lanthanum chloride-sulfate)

Jan 1, 1980

By Dight P. M

The challenge of narrow vein mining is to produce ore with as little dilution as possible, at the least cost -commensurate with the increasing degrees of safety being demanded for mine workers by the modem &apos;duty of care&apos; legislation. Geotechnical factors play an important, if not overriding, role in these areas. The geotechnical factors cover the complex interaction over a period of time, between the in situ and induced rock stresses, rock structures, rock mass strength and the cable, rock bolt and other ground support members. In the Archaean schist belt areas where many of our narrow vein mines occur the pre-mining in situ rock stresses are commonly significantly higher than the overburden stresses. These are concentrated in areas beneath previous open pits and may be highly concentrated in the pillars and abutments of stopes on narrow veins. The presence of high in situ stresses may be suspected from the appearance of drill cores and underground development long before they become sufficiently concentrated by mining to cause damage or bursts. These initial indications are discussed and modem low cost methods of stress measurement are described. Practical and quick methods of analysing the stress redistribution around scopes and other underground excavations are now available and guidelines for interpreting them in terms of rockmass characteristics, stope stability and support requirements are developed with the object of increasing safety, whilst reducing overall costs and dilution.

Jan 1, 1993

By A. G. Spencer

"The horsepower required to drive large grinding mills has increased dramatically during the past ten years. Limitations on the amount of power which may be transmitted by a single gear and pinion have resulted in the application of multimotor drives, with consequent loadsharing problems. It has also sparked the development of some entirely new drive concepts. In addition, the severe demands made upon the electrical system during the acceleration period have required that the selection of motors and electrical system design be closely coordinated. Moreover, the installation of such large process units results in downtime being very costly. The equipment selected and the plant maintenance philosophy must therefore be such as to minimize the risk of unscheduled downtime."

Jan 1, 1972

By B. M. Larsen

SEVERAL articles have recently been published discussing the conditions necessary for accurate measurements of temperatures in the open-hearth steel furnace. In the course of a study of refractories service conditions in steel furnaces, the present writers have taken tempera; tunes in several open-hearth shops in the Pittsburgh district. The conclusions, as to conditions necessary for accurate measurements of temperature, are somewhat at variance with those of other investigators. The subject is closely connected both with the close-control of steel-making and the prevention of overheating of the silica refractories used in roofs and walls. It is becoming more and more important to obtain furnace temperatures of fairly definitely known accuracy. At present, the most useful instrument for such measurements is the disappearing-filament type of optical pyrometer. This method of measurement has formed the basis of most other discussions on the. subject and was also used by the writers.

Jan 8, 1926

By W. P. Blacutt

A financial-economic model incorporating physical, market, and policy variables is developed for mining investment in Bolivia. Additional risk criteria emanating from political instability. new mining legislation, recent environmental regulations, and a new minerals taxation system are accounted for and are integrated into the investment decision model. Results of the model indicate that geologic and market variables have the dominant effect on the investment-worth function. Among policy variables, exchange rate and taxation policies have the most significant influence. Depreciation allowance for infrastructure development has negligible weight in the investment-worth function. The business structure of the firm considering investing in the Bolivian Polymetallic Project is found to be an instrumental factor in the investment-worth outcome. Specifically, undiversified mining companies whose operations exclude zinc production as the primary source of revenue would benefit most from adoption of this project.

Jan 1, 1993

By A. Beitz, P. Smartt, G. Einicke, G. Rowan, P. Glynn

Coal is Australia’s highest export earner and Australia is the world’s largest exporter of coal. With coal now being extracted from deeper reserves under increased risk profile, and in the interest of aiding the stability of coal supplies, Japan is funding a number of safety projects in Australia and China. The CSIRO, Australia’s premiere research organisation with the country’s largest exploration and mining research group, are currently undertaking a jointly funded Japan-Australia safety project at Anglo Coal’s new Grasstree Colliery in central Queensland. The project, entitled Mine Communication and Information for Real-time Risk Analysis, will deliver step-change capabilities in data integration, decision support, gas monitoring, geo-technical monitoring, emergency response and personnel safety to the Grasstree Colliery. Some key activities include: developing and installing underground coal mine Ethernet LAN components, real-time monitoring of gas and geo-technical sensors, MODBUS serial to TCP/IP converters, e-reporting of underground conditions, emergency guidance systems and underground trials of Internet Protocol telephone and video. The project seeks to integrate (in real time) key data sets from the comprehensive and diversified range of propriety system currently in use at mines (ventilation, strata, operations e.g. haulage, pumps, conveyors etc) into a single integrated risk management interface. This interface will filter the data through a rules-based inference engine that will cross reference the various data streams, compare with past events and outcomes associated with the similar historical data and present this “intelligence” to

Jan 1, 2003

By F. N. Voskoboyev

The suggested new method for control of geomechanical state of undermined rock mass ensures, as a safety measure for the earth surface protection, the decrease of deformations by 2,5 - 10 times in mining the single seam, and by 1,5 - 5 times - in mining bed series, i. e. approximately within the seam ranges as in the application of full packing with various compressive properties or partial extraction of resources over the area with different coefficients of extraction. It should be noted that this new method has the following advantages o\w rhr. conventional methods: a) the decrease of the packing area and packing works volume by 2 - 4 fold including the operating and productive expenses; b) the elimination of mineral losses due to the increase of extraction coefficient up to 100 5%; c) rock utilization from workings drivage by its placing in the mined - out space. Perspective field of application of this method: disconservation of mineral resources in the left protective pillars of various designation.

Jan 1, 1996

By K. Voltaire

As can be guessed from the subtitle, this paper will not be a geologist&apos;s one since neither of the authors is a professional geologist. This will be an attempt to present the various aspects of the legal, economic and geological setting that condition the exploration for mineral resources in Haiti. Before going any further, we are going to present a summary of our rather short mining history. One must first mention that Caribbean countries are latecomers to the mining business. If we go back to the colonial period (1500-1600&apos;s) there are net many traces of mining activity. The major exception to this is the recovery of alluvial gold in Hispaniola, Puerto-Rico and Cuba and also some sporadic copper mining in Hispaniola (notably in Haiti near the city of Gonaives and in some of the old mining districts in Santo-Domingo). These easily minable deposits were quickly exhausted and mining quite naturally came to an end as agriculture rose as the major economic activity. In the Haitian case, aside from very erratic mention during the 19th Century of the presence of some minerals (i.e. haematite, chalcopyrite) no serious geological work was undertaken. In the meantime, the peasants in the northern part were still looking for alluvial gold in some streams but this amounted to next to nothing. One has to come to the 1920&apos;s to find the first comprehensive geological survey. At the time, the country was under the military control of the United States. The American Government sent a team from the U.S.G.S. headed by the late W. Woodring to initiate a survey of the country. Given the lack of transportation, this was a tough task and Woodring and his associates did it magnificently. As a result of their efforts, they published a very thick piece of work of more than 600 pages. "The Geology of the Republic of Haiti" although it was published in 1924 is a classic and is a must for anyone interested in the geology of Haiti.

Jan 1, 1978

By J. E. Wey

Extraction of cobalt from cobalt sulfide and cobaltite flotation concentrate from the Blackbird Mine, Idaho, was investigated using an adapted strain of Thiobacillus ferrooxidans. Cobalt extractions as high as 100% were realized in the inoculated experiments, whereas only 4% extraction was obtained in the sterile run. The influence of pulp density on the rate and extent of cobalt extraction was also determined. It was found that the extraction of cobalt followed predominantly the indirect mode of bacterial activity. In this process, ferric iron oxidizes cobaltite to cobalt sulfate and ferric arsenate while being reduced to its ferrous state; the bacteria continuously re-oxidize ferrous to ferric iron. Electrochemical measurements using cyclic voltammetry suggested that cobaltite oxidation involved a number of intermediate reactions.

Jan 1, 1993

By Zsuzsanna Zborovszky

A circuit is considered intrinsically safe when any spark or thermal effect produced normally (that is, by operating the equipment in its correct operational manner to fulfill its purpose) or accidentally (caused by short circuit, earth fault, defective components, breaking the wiring, etc.) is incapable under prescribed test conditions of causing ignition of a prescribed gas mixture. The test conditions and gas mixture should be at least as hazardous as the true parameters of the environment where the circuit will be operated. According to present practices, the question of whether or not a circuit is intrinsically safe is decided upon experimentally. The circuit is inspected first for mechanical soundness and a survey is made to determine what faults should be considered as probable. Then the individual branches are connected, in sequence, to a test apparatus called &apos;breakflash" which acts as an opening, closing contact and thus draws sparks from the circuit. This test is repeated a given number of times in the presence of the prescribed gas mixture under specified conditions (electrode configurations, gas parameters, etc.). The equipment will be regarded as intrinsically safe if during testing no ignition has occurred.

Jan 1, 1972

By Karl Christopherson, Vanessa de Viterbo

Trim blasting is an integral part of the mining processes at the Morenci Mine, a Freeport-McMoRan Copper & Gold Inc. property. Trim blasting near high-walls or Finals blasting requires a tighter distribution of energy but a reduction in total energy factor near the wall. Recent Finals blasting in Morenci Mine was allowing the shovel to dig to the final design limit, but causing high-wall instability due to excessive energy or production of energy (blast design and timing). Slope instability events reduced production in two of the three operating pits in Morenci over 2009. In order to avoid high-wall instability from Finals blasting, a new method was required. The new method utilizes air-decks, unconventional row timing, and blast design based on the geology predicted. Many different geologic structures and rock types exist in Morenci, and different strategies were needed for the many predicted geologies. Drill penetration rate and core mapping were the primary tools for determining the blast design. Patterns were designed within a consistent geology; with weaker rock types receiving a lighter load than the stronger rock types. Penetration rate returned by the drill would be the determining factor on the actual rock hardness. Maintaining the pattern geometry on Finals designs should not be an issue as long as the lb/hole is adjusted to reduce powder factor close to the high-wall. One requirement of Finals blasting should be that the powder factor matches the geology as closely as possible. A softer, fractured zone should use approximately one-half to two-thirds the explosive charge of a competent, sound geological zone. This has been incorporated into the final Trim blast design. It is impossible to protect every high-wall from close-in blasting, especially those with crossing prominent joint sets inclined toward wedge failure, but this new design has provided protection on walls where the mine was encountering problems.

Jan 1, 2011

By John C. Bilello

The brittle fracture behavior of cold-worked sintered tungsten was studied over the temperature range 4.2° to 298°K using a high-sensitivity strain measuring system and electronfractography. Similar observations were made on a swaged electron beam zone-refined monocrystal. In sintered tungsten irreversible plastic deformation was observed during cyclic load-unload tests at stress levels well below the fracture stress for all temperatures, but general microyielding could be detected only down to 202°K. For the zone-refined samples macroyielding occurred at all test temperatures with evidence for twinning below -202°K. The fracture stress of the sintered tmgsten was virtually independent of temperature, while the zone-refined crystal showed a 2.3 times increase over the same temperature range. Electronfractography confirmed the presence of numerous rod-shaped and spherical submicroscopic voids which ranged in diameter from 1400 to 4300A in the sintered tungsten; no voids could be found in the zone-refined tungsten. Contrast effects observed on the replicas in the vicinity of certain voids indicated that plastic deformation could be induced by the local stress concentration. It has been suggested that the presence of these voids may be responsible for the low-temperature brittle failure of sintered tungsten. Based m this suggestim und on the evidence obtained here, a dislocatim model is presented to account for the brittle behavior of sintered tungsten. In this model slip, which is induced by the local high stress concentration in the region at the edge of a favorably oriented void, could cause the void to grow to a microcrack of critical size. STUDIES of brittle fracture in bcc metals have led to the well-known experimental relationships between grain size, yield stress, fracture stress, and temperature which have formed the basis for the various dislocation pile-up1-3 or interaction4&apos;= models for slip-induced microcrack nucleation. While microcracks can be nucleated by deformation twins,6,7 there has been no direct evidence furnished by transmission electron microscopy to support conclusively either the Zener pile-up or Cottrell dislocation reaction models for producing micro-cracks in all "brittle" materials. In addition to the "inverse" grain size relationship for yield and fracture stresses the cottrel14 theory predicts that the fracture stress below the transition temperature should behave in a fashion similar to that of the yield stress above this temperature. Such behavior has been verified for several bcc metals.8-10 With reference to both grain size effects and the tem- perature dependence of the fracture stress below the transition temperature, the behavior of sintered tungsten appears anomalous. Early work by Bechtold and Shewrnon 11 showed no apparent temperature dependence of the fracture stress below the ductile-brittle transition temperature (DBTT). They attributed this result to the intergranular nature of the fractures observed. More recent work by Wronski and Four-deux12&apos;13 on considerably purer material did not show any systematic relationship between the fracture stress and temperature below DBTT. The dependence of flow and fracture stresses on grain size is also not clearly established for sintered tungsten. Koo, for example, has shown that the DBTT for sintered tungsten depended chiefly on the annealing temperature and was relatively insensitive to the actual grain size achieved. Using electrofractography and transmission electron microscopy, Wronski and Fourdeuxl3 showed that numerous spherical and rod-shaped submicroscopic voids could be found in sintered tungsten but not in melted tungsten of nominally the same purity. They suggested that these voids could be responsible for the temperature insensitivity of the fracture stress below the DBTT. In the present work the temperature dependence of the fracture stress for high-purity commercially sintered tungsten has been determined. The presence of submicroscopic voids in sintered materials was confirmed, and these were studied in detail to examine the role they could play in nucleating brittle fracture. A dislocation model is suggested which could cause an inherent spherical void to lengthen into a Griffith crack of critical size. EXPERIMENTAL PROCEDURE Commercially sintered tungsten rod was obtained in the as-swaged condition from Sylvania. A zone-refined crystal was obtained from the same source. This crystal was grown by giving three zone passes (at 25.4 cm per hr) to a sintered rod of high-purity tungsten. The rod axis prior to cold working was -15 deg from the [110] direction. Originally the zone-refined rod was -6 mm in diam; it was reduced to -3 mm by eight swaging passes, at high temperatures, with each step having about the same reduction of area. The final swaging step gave a 7.5 pct reduction of area at 1050°C. All swaging operations were performed in a hydrogen atmosphere. For the sintered rod a similar working schedule was employed. Metal-lographic examination of the sintered material revealed that the cold-worked structure had an apparent grain diameter of -25 u transverse to the swaging direction (obtained by the intercept method). In the longitudinal direction cold-worked grains were approximately 1.5 to 2 times their diameter. No distinct fiber structure could be observed optically for the zone-refined rod. The cold-worked structure in the

Jan 1, 1969

By Cui Wang, Kexin Jiao, Qiuye Cai, Jianliang Zhang

Prolonging the campaign life of the blast furnace has been an important task for iron makers, and it has been studied for decades. Adding titanium-bearing materials is a generally agreed and effective technique to protect the blast furnace hearth. Titanium from titania additions in the burden or tuyere injection react with carbon and nitrogen and form scaffolds on the hearth surface to protect the hearth from subsequent erosion. In this article, the progress on blast furnace hearth protection of titania additions in Chinese steel companies and research institutions is investigated, and the difficulties in the operation and production, such as little effect after adding titaniumbearing materials and the property deterioration of liquid iron and slags, are analyzed. The future research for protection in Chinese blast furnace is proposed, and a comprehensive process which combines protection of titanium bearing materials with reasonable thermal balance and slagmaking regimes should be established.

Jan 1, 2015

By James Westfield, S H. Ash

Because of the increasing shortage of fuel in the United States, especially of residential fuel in the Eastern and New England States, it was essential that the maximum production of anthracite be obtained to help win the war and to prevent human distress. The nine railroads that depend on the anthracite region for a substantial portion of their business were not congested unduly with other traffic, because the region was not participating in industrial activities to the same degree as in many other sections of the United States; consequently, transportation of anthracite to the New England States, New York, New Jersey, and eastern Pennsylvania over a shorter rail haul than for any other fuel was desirable. The prevention of floods that would cause a loss of anthracite production was important to the war program. Every shutdown deprives the northeastern section of the United States of anthracite that is needed badly. Failure to prevent inundation of anthracite mines halts production, endangers the lives of workmen, damages, sometimes beyond repair, vital underground equipment, and threatens the permanent loss of a large portion of the Nation’s anthracite reserves. Funds were made available to the Department of the Interior, Bureau of Mines, for the fiscal year ended June 30, 1945, through a supplemental appropriation for anthracite investigations, one of which was to conduct inquiries and scientific and technologic investigations that have a bearing on the anthracite mine-flood problem. As part of the investigation, the Bureau proposed to obtain the cooperation of the anthracite-mining companies and the State in effecting a program to prevent the inundation of mines in the anthracite region. No large engineering projects were undertaken by the Bureau during the fiscal year ended June 30, 1945, on the anthracite mine-flood problem. Small projects were chosen that could be completed within 1 year to prevent loss of anthracite production at a critical time. It was believed that such projects would lessen the chance that flood water would inundate active mine workings.

Mar 1, 1946