Search Documents

By C. D. Woodward

THE subject of electric signals for the despatching off mining cages through shafts has received cousiderable attention recently from various mining companies. The Anaconda Copper Mining Co. has found it necessary to develop a system that is reliable, safe and simple in operation, and easy to repair. The movement of all mine cages or skips is under the direction of a station tender, who rides on the cages when men or supplies are being lowered or raised. When ore is hoisted, he is stationed at a skip pocket for loading and despatching the skips. For the station tender's use, two signal systems are installed in each hoisting compartment, and he is the only employee authorized to use them. One system is known as the "AC" or Station bells, as it is operated from the 110-volt, 60-cycle, power service; the other system, called the "DC" or shafts bells, takes its energy from closed-circuit primary batteries. As a supplement to the two main signals, a buzzer system is installed. The general arrangement is similar to "the main signal, except that there is a mine buzzer at each station. When a signal switch connected into the buzzer system is pulled down, all buzzers are operated, thus notifying the station tender that he is wanted at some particular level. Placed on the station posts, and within easy reach of the men on the cages, are the signal pull switches for the main signals. The station, or "AC," pull switches are furnished with a short rope as shown in Fig. 1, while the shaft, or "DC," pull switches are equipped with ropes that extend down the shaft past the next station. To avoid all confusion in the use of the three signal systems, a standard arrangement has been adopted in all mines for the location of the pull switches. Fig. 2 illustrates the position of the pull switch at the various mine stations for the main signal systems, but it does not show the buzzer pull switch; this is fixed to the roof timbers about 25 ft. back from the shaft. If the skip pockets are a considerable distance below the station, a pull switch for each main shaft compartment is connected to the "AC" system and placed at this point. However, if the distance is short, a light cord is attached to the station pull switches and dropped down to the skip pocket.

Jan 2, 1922

By K. Rüter

Sustainable investment is a global growth market. Companies that can reconcile economic, environmental and social objectives not only minimise risks, but also realise significant potentials of added value. This particularly applies to the metals & mining industry, as it is an attractive sector for investors and, at the same time, faces major challenges in the field of sustainable development. oekom research AG is an independent rating agency specialised in the analysis and evaluation of the environmental and social performance of companies, sectors and countries for institutional investors and financial service providers in the socially responsible investment (SRI) sector. oekom research has been active in the sustainable investment field since 1993 and its research is currently being used by managers of more than 60 bond and share funds with a volume of assets totalling more than 4.5 billion Euro. The company?s research and its central instrument, the Corporate Responsibility Rating (CRR), are based on the world's most comprehensive set of criteria for the ethical assessment of companies. With the support of an independent scientific advisory board, these universal and industry-specific sustainability criteria are being constantly updated reflecting the dynamics of global challenges in sustainable development. Increasingly, the rating results and benchmark reports of oekom research are also being recognised by the companies as a valuable tool to identify best practices, areas for improvement, and potential risks. This paper will outline the methodology of oekom research, the identification of key sustainability issues in the metals & mining industry, the development of industry-specific sustainability criteria (indicators) for the assessment of the metals & mining industry and key findings of the recently completed CRR of twenty major metals & mining companies.

Jan 1, 2007

By Marcelo A. Martorano, Moyses L. Lima, João B. F. Neto

"Directional solidification is an essential refining step to obtain solar grade silicon from metallurgical silicon. This step can be carried out in a Bridgman furnace, where nearly constant temperature gradients and solidification velocities are imposed on the solid-liquid interface. In the present work, this directional solidification was conducted in a static furnace, in which large temperature gradients and low solidification velocities were enforced to increase macrosegregation. The resulting ingots were analyzed regarding their macrostructures, microstructures and chemical composition. Using measured cooling curves in the ingot as boundary conditions, a mathematical model based on the concept of a stagnant liquid layer at the solid-liquid interface was implemented to predict the macrosegregation profiles. The chemical analyses of the ingots show macrosegregation of several impurities to the ingots top. The mathematical model indicates that liquid convection plays an important role in stabilizing the planar solid-liquid interface, increasing the macrosegregation of impurities.IntroductionMost of silicon used for photovoltaic (PV) energy production is obtained by chemical processes, such as, Siemens and its derivations [1]. However, these chemical processes have drawbacks related to relatively high energy consumption and investment costs, and to safety and environmental problems. In order to overcome these difficulties and to fulfill the silicon demand for PV applications, several metallurgical routes are under development [2] to produce silicon of enough purity to PV applications (SoG-Si) from metallurgical grade silicon (MG-Si).Metallurgical routes involve different steps among which the directional solidification is pointed out as a fundamental one [1]. Directional solidification can cause macrosegregation of impurities to the last part of the ingot to solidify. The impurity segregation during solidification is related to the low solute partition coefficient (k0) between liquid and solid silicon. Most of the impurities in MG-Si have k0 << 1, except for boron, phosphorus and oxygen, which require specific steps of the metallurgical routes to be eliminated. The equilibrium partition coefficient and the solubility limits for the most important impurities in MG-Si are shown in table 1"

Jan 1, 2014

By C. C. Hwang

The Bureau of Mines formulated a method for calculating the concentration of entrained dust from a dust deposit by a turbulent gas stream. In particular, a diffusion equation is used to calculate dust concentrations in a channel following an explosion. Dust leaving the channel walls was treated as originating from stationary or moving, and single or multiple material sources. Formulas and sample computations for various types of dust sources in circular and rectangular channels are given, based on experimental entrainment rates. The analysis predicts the dust concentration as a function of time and channel space. The results appear to agree with the physical characteristics of explosion-driven dust dispersion in a O.6-m-diameter, 50-m-long explosion tunnel. The analysis is also applied to simultaneous and consecutive dispersion of coal and rock dust from simulated coal mine surfaces (walls, floor, roof, and ribs).

Jan 1, 1974

To develop a simple device for rapidly determining the shearing strength and angle of Internal friction of coal and rock in situ. Approach Use a portable, permissible, hydraulically operated device in boreholes as deep as 100 feet into the rib, floor, or roof of the mine. How it Works The device, called a Borehole Shear Strength Tester (BST), is inserted Into a 3-inch-diameter borehole to the desired depth, locked Into position, and activated to shear the rock or coal in the borehole walls. The normal and shear pressures exerted by the BST, which are recorded during the test, are used to calculate the shearing strength and the angle of internal friction. The BST consists of 3 main components and several minor components. Main components are: ? A shear head with 2 shear plates that bite into the rock when normal pressure is applied. ? A hollow hydraulic jack with RW drill rods that pull the shear head when shear pressure is applied. ? A console with a hand pump and two hydraulic gages to activate the device and to indicate the pressures that apply the normal and shear faces to the shearing plates.

Jan 1, 1981

By Edwin W. Tooker

Creation of needed new resources will be accomplished mainly by imaginative and diligent geologic exploration because geologic availability is the key determinant of future mineral supply. Adequate resources of most commodities can be made available for the rest of this century and beyond if they are discovered. Thus conversion of hypothetical and speculative resources into available reserves will provide the principal challenge to earth scientists. Additional problems now compete for our attention. First is a challenge to discover more resources than have been found to date for domestic needs as world-wide demands increase exponentially and as easily found high-grade deposits are rapidly being depleted. New ways to find new types of deposits are required. Second, the United States, a resource importer, increasingly is challenged for access to foreign supplies through stiffening competition and economic or expropriation sanctions. Balancing needs for mineral supply and environmental protection is a third challenge. Geologic explorers must consider statutory as well as economic and technologic requirements, controlled access to public and private lands, competition with urban sprawl or wilderness, limitations on discovery, appraisal and mining methods, and restoration of mined areas. Finally, is the challenge to temper public and private attitudes and assure that decisions bearing on resource problems are based on comprehensive credible facts. While striving to maintain and improve the standard of living, many Americans appear to disdain and mistrust those organizations that provide their material where-withal. Meeting these challenges effectively, and in time, will require careful appraisal of the resource system and the joint efforts of industry, university, and government earth science research.

Jan 1, 1974

By D. Kwak, S. Han, J. Kim, Y. Lee

"INTRODUCTION In carbonate rocks, it is difficult to characterize due to the high degree of heterogeneity in pore geometry. Carbonate rocks have various types of pore systems such as fractures and vugs, and this heterogeneity should be considered for more realistic prediction of oil production in carbonate reservoirs. This study carried out water flooding experiments using five carbonate rock samples in order to observe the change of physical properties. Firstly, qualitative and quantitative analyses were conducted for each carbonate samples by use of XRD and XRF to evaluate the mineral content. All samples are mainly composed of CaCO3 and after that, the ICP experiments were carried out for the water passing through the carbonate. As a result, it was possible to measure the quantity of CaCO3, MgO, Fe2O3 component in water and due to this effect, the permeability of carbonate was altered especially in the front part of the core. Finally, after the carbonate was saturated by 30 API crude oil, water injection to enhance the oil recovery was repeated and it was confirmed that the oil-producing characteristics are different depending on the dissolution characteristics of carbonate rock samples. CORE SAMPLE ANALYSIS Porosity and Permeability Experiment Porosity and permeability were measured. The procedures are as follows (Figure 1). 1. Measure the diameter and length of the dry core using Vernier caliper. 2. Put the core in the core holder, run vacuum pump until the inlet and outlet pressure gauge equal. 3. Saturate the core using ISCO pump to inject water at 650 psi 4. Measure the amount of water and calculate the porosity 5. Set up the outlet pressure at 500 psi. 6. The flow rate measure when the equilibrium 7. Calculate the permeability through Darcy’s Law. 8. Cutting of core upstream and downstream about 13cm, and measure the each of permeability."

Jan 1, 2016

By Goode A

Since 1985 there has been a revival in the alluvial gold mining industry in North Queensland. However, not all mines which have been established have been successful, some times due to a misconception that alluvial mines are quick to establish and easy to operate. A check list of factors which need to be considered when assessing alluvial mining projects in North Queensland is presented and their relative importance is briefly discussed.

Jan 1, 1989

By Notman, Arthur

THIS is a day of surpluses, some good and some not so good. One can hardly pick up a newspaper, magazine, review or economic treatise without confronting the fact that we have or are threatened with more .of certain goods than we have use for, whether it be corn, wheat, cotton, coal or oil, -lumber, &apos;leather, newsprint, automobiles, zinc, lead, copper or what not. How did this unprecedented state of affairs arise? Who is to blame? How shall we avoid smothering ourselves in our own production? The voice of the farmer is raised in appeal to the Government to relieve him from the dilemma of his own fertility. In answer the Government employs thousands of experts and spends millions of dollars to aid the farmer. But to what end? To make him still more efficient so that he may produce even greater surpluses? Not satisfied with the result, it spends other millions to prepare vast areas of the arid land of the West for more farmers to cultivate and insure yet larger surpluses. Then what? Naturally another appeal to the Government to fix prices by financing the

Jan 1, 1928

By T. Bennett

Geothermal energy has the potential to provide 20% of the UK's annual average electricity generation capacity requirement. This article discusses the costs and potential benefits.

Jun 1, 2015

By R. L. Loofbourow

Reasons for reexamining underground mining include: 1. The assurance that more deep deposits of useful minerals will be found. 2. The existence of deeply covered deposits of industrial minerals near large markets where quarries are becoming depleted or are lacking. 3. Surface property values, zoning and other limitations on open pit mining. 4. Expectation that underground space will be increasingly used for transportation, power plants, storage and similar purposes. 5. The improvements which have been made in underground mining. During the last three or four decades many changes and improvements have been made underground. All underground construction and mining has benefitted to some extent but the effect on the productivity of labor employed with some methods- has changed little and the use of these methods has declined. Productivity of labor in other methods has increased substantially. The relative usefulness of mining methods has changed and a vital industry, bituminous coal, has been returned to health. In this paper, consideration is limited to nine methods used with high productivity during the period under review. These methods are not necessarily better than others but they may be considered the prime methods in the sense that, in our economy, many, low grade ores, coal and the principal industrial minerals could hardly be produced by less productive means.2 Although most of the examples cited are from mining as such., the first four methods discussed can be used for the construction of stable excavations of various&apos; shapes in sound rock.

Jan 1, 1967

By W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-element method for evaluating shaft pillar mining plans and shaft stability. This report focuses on mine measurements and calibration of the two-dimensional computer model and is the second in a series of three Reports of Investigations describing the Ross shaft study. In this study, borehole extensometers and other instruments were installed to provide data for model verification and to monitor the shaft. Results of the recalibrated two-dimensional model (UTAH2) confirmed the premining stability evaluation. However, after mining began, concern was expressed because cracks and other signs of ground motion appeared at considerable distances from the area of active pillar mining. In part 3 of the study, an intensive three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the observed effects were within expectations and that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 2010

By C J. Corbett

Many underground mining methods rely on blasted rock moving under gravity to report to extraction points. Mining of orebodies dipping between 20 - 45 degrees poses a unique challenge for mining engineers in that a dip angle in this range will not allow the movement of broken ore down the footwall to the mucking horizon utilising gravity. This is more so in cases where the natural angle of repose of the rock is less than the dip of the orebody. Hence, innovative mining systems are necessary to mine this type of orebodies. In Australia, the method of uphole retreat panel stoping is commonly used to extract orebodies in the dip range of 20 - 45 degrees and thickness range of 5 - 15 m. In the Zambian Copperbelt a method called continuous retreat updip stoping is used for orebodies with similar dips and thicknesses. The mechanised form of this mining method has potential for application in the metalliferous mining industry in Australia. In this study a comparison is made between mechanised updip (MUDS) and transverse retreat stoping (TRS) methods. A hypothetical nickel sulphide orebody located in Western Australia is used as case study. The net present value for mechanised updip stoping is seven per cent higher than that of transverse retreat stoping based on the assumptions applied. Initial results of this study indicate that mechanised updip stoping can be adopted for Australian mining conditions. However, lack of significant local experience with the method is often cited as a reason for not adopting it even in situations where it is clearly the best option.

Jan 1, 2003

By F. S. LOTT

Publication of the Bureau of Mines annual surveys of the capacity of petroleum refineries in the United States was suspended after the entry of the United States into World War II . The last published survey was that of January 1 , 1941 , released in April 1941 as Information Circular 7161 . The purpose of this publication is to provide comparable information with respect to crude - oil and cracking capacity on January 1 , 1947. No attempt is made at this time to bridge the gap in annual statistical series from the date of the last published survey to the present one . However , complete summary tables will be included in the succeeding survey for January 1 , 1948 .

Mar 1, 1948

By Ma Guang, Huang Jinshou

In this paper we briefly describe measuring techniques and their practical use in the mining industry of China. A strain coefficient matrix of triaxial strain cell for a flat ended borehole is also introduced.

Jan 1, 1983

By Fritz F. Prugger

This paper considers some of the main aspects of underground mining in the flat, rich, but deep lying deposits of Saskatchewan. It briefly describes the pertinent geological features as they relate co mining and the practical de-stressing techniques used to allow productive extraction in the high stress environment present in many of the province&apos;s mines. Fining layouts, materials handling and the evolution of some of the world&apos;s largest mining equipment are examined.

Jan 1, 1980

By Mohammad Ranjbar Hamghavandi, Mohammad Ranjbar, Zahra Manafi, Mohammad Hassan Fazaelipoor, Mahin Schaffie

The present study introduces a new approach to understand the copper dissolution rate and to find an adapted mathematical statement for particle shrinkage rate in a batch bioleaching system. Four size classes of a chalcopyrite concentrate, namely [D1 : (−54 + 44)μm, D2 : (−44 + 38)μm, D3 : (−38 + 25)μm and D4 : (−25)μm], were used in the batch bioleaching tests by applying a mixed culture of moderately thermophilic microorganisms. The pulp density and temperature were 8 (%w/v) and 50 °C, respectively. Findings delineated that the bioleaching time can be divided into two specific time intervals: first, the surface reactions were the prevailing controlling step; second, the prevailing mechanism was diffusion through the product layer, whereas the overall rate of the process may be related to both through a Q factor using a mixed model. A mathematical model was developed based on particle size distribution (PSD) and a kinetic model. Experimental validation of the mixed model was accomplished by the representative sample with d80 = 54 microns. Results showed that the PSD of the specific sample was in good agreement with Rosin–Rammler function. Besides, the simulation result of the conversion fraction had the best conformity with the experimental data (with a maximum error of approximately 7%). This paper should be considered as an initial part of a larger, global model for chalcopyrite concentrate bioleaching.

By Grey CA

Any economic evaluation of a lead-zinc mining project requires the estimation of net revenue per tonne of concentrate at the "mine gate". The value at the mine gate equals the Net Smelter Return minus all realisation costs. The paper develops a simple predictive model for Net Smelter Return based on metal prices.

Jan 1, 1990

By Shunichi Ajima

PT. Smelting Co. was established in February, 1996 to construct and operate the Gresik Smelter and Refinery. The construction work of first Copper Smelter and Refinery in Indonesia was completed in the end of August, 1998 and it was put into the integrated test operation in December, 1998. Gresik Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from copper concentrate supplied from Grasberg Mine of PT. Freeport Indonesia Company in Irian Jaya, Indonesia. As by product 592,000 tpy of sulfuric acid, 382,000 tpy of slag, 31,000 tpy of gypsum and 480 tpy of slime will be produced in the full operation. Major processes applied at Gresik Smelter and Refinery are: Smelter: Mitsubishi Continuous Copper Smelting and Converting Process ( Mitsubishi Process ) Anode Casting: Continuous Casting of Copper Anodes with the Hazelett Twin Belt Caster Refinery: ISA Process Acid Plant: Lurgi Mitsubishi Double Contact Process

Jan 1, 1999

By PDF

Flotation columns are widely used in mineral processing and coal preparation industry today. Mathematical modeling of flotation columns has conventionally been done using axial dispersion or tank-in-series models. However, for design and scale up purposes these models are not adequate enough because they do not provide detailed information of the flow fields within the column. This paper presents a Two-Dimensional, Two-Phase. Fluid-dynamic Model and its numerical solutions for some cases encountered in column flotation. The MAC (Marker and Cell) method was employed to obtain the numerical solutions, and based on this method a computer code COLUMNFLOW was developed. The simulated flow field reveals the presence of a circulation flow structure in flotation columns, which could be one of the main reasons for mixing in column flotation. The effects of some parameters such as superficial gas and liquid velocities on the characteristics of the flow structure in flotation columns were also tested with the numerical model.

Jan 1, 1994