Search Documents

Research personnel from the Bureau of Mines, a representative of the Mine Safety and Health Administration, and research contractors for the Bureau of Mines met with other Government and industry representatives at three seminar locations in December 1980 to discuss the findings and products of Bureau research on mine safety training. The research program is aimed at providing assistance to the mining community in its efforts to reduce industrial-type, human-error accidents through research establishing performance based methods and media for employee training. Research emphasis is directed toward development of baseline materials and instructional models; development of methods for structuring and evaluating health and safety, supervisory, and occupational training; and the continued investigation and application of current learning and simulation technology that could significantly enhance the effectiveness of training opportunities.

Jan 1, 1981

By R. K. Linn

The New Idria Mining and Chemical Co. owns and operates the New Idria mine in southern San Benito County, Calif. During 1957-59, the New Idria mine was the largest producer of mercury in the United States and its alltime production of over a half-million flasks was exceeded only by one mine. It is one of the oldest and most consistent producers in California. With the exception of 1921-22, the mine has an annual production of mercury dating back to 1854. This paper by the Federal Bureau of Mines describes the exploration, development, mining, and furnacing of mercury ore at the New Idria mine. Figure 1 is a view of the furnace plant of the New Idria mine. The purpose of this report is to promote the development and conservation of our mineral resources by dissemination of technological information on mining and processing procedures, and related practices at operating mines.

Jan 1, 1961

By William C. Cooley

A technical and economic study was made of the feasibility of establishing an underground hydraulic coal mine in the Wilkeson-Carbonado coal field approximately 25 miles southeast of Tacoma, Washington. The deposit contains reserves of more than 200 million tons of generally high quality metallurgical coal. It is located in nine seams of minable thickness in a complex, folded and tectonically disturbed set of anticlines and synclines. Typical dip angles are up to 60°, with minable seam thicknesses of 6 to 17 feet. A mine plan was made for a 2 million TPY mine (clean) using two shafts to access the deposit to a depth of 2500 ft. The mining method uses monitor jets to break coal by sublevel retreat mining, fluming to a sump and pumping the minus 0.25 inch coal to the surface and to a preparation plant. The plus 0.25 inch coal is hoisted by skip. Cleaned met coal would be shipped by rail for export. A middlings product would be sold as thermal coal. Assuming a coal price of $48 per short ton (FOB the mine) for the met coal and $35 for the middlings, the return on investment is estimated at 20% after taxes. The many uncertainties about the geological conditions and the specific mine design parameters make the economic analysis and conclusions somewhat tentative. A second mine could also be developed in the eastern section of the reserves to produce 1 million TPY of clean coal and is expected to have similar economics. Recommendations are made for a Test Mine and a Pilot Mine leading to a production mine.

Jan 1, 1983

By P. A. Witherspoon, Y. W. Tsang

Normal stress-fracture closure variation and stress-dependent fluid flow rates were calculated for rock fractures of different aperture distributions. This study shows that both the mechanical and hydraulic properties of the fracture are controlled by the large-scale roughness of the rock fracture. Hence the typical large-scale undulation wavelength of the rock joint dictates the suitable sample size to be used in normal stress and fluid-flow measurements, if results due purely to sample size are to be avoided.

Jan 1, 1982

By A. L. Labbe

IT Is well known that the Cottrell process is more easily applied to certain kinds of smoke than to others. The successful Cottrell installations are those treating smokes that carry dust of a mechanical nature; also smoke carrying fume dust that contains an excess of sulfuric acid over that required to combine with the oxides in the dust. But up to the present time the process has not reached a satisfactory economical basis of operation, in the treatment of smoke' containing basic dust. It is not impossible to make a smoke containing basic dust suitable for the process by. humidifying or acidifying. A number of Cottrell plants use these two methods of conditioning smoke previous to Cottrell treatment, which are quite successful, but the use of either results in expensive operation and a substantial loss in metals.. For these reasons, I would say that the baghouse process has not been replaced by the Cottrell process in the treatment of smelter basic smoke. Basic smoke must be given a. preliminary conditioning treatment because the dust is not a conductor of electricity; the water or acid treatment imparts some conductivity to the dust.. The rate at which dust is recovered depends on the proportional amount of power transmitted to the, treater and on the rate at which the smoke passes through; therefore to maintain a maximum constant amount of power across the electrodes of the treater, the same degree of conductivity should prevail, at all times between the surface of the electrodes. For all practical purposes, in the application of this process to lead and copper-smelter smoke, we can consider that the conductivity of the gases is a .constant. The variations in temperature of the smoke have a much greater effect on the solids than on the gases; the only instance where the temperature of the gases plays an important part in the process is at plants using humidifying: The temperature does not affect the conductivity of mechanical dust because such dust has natural conductive properties. However, in the case of smoke carrying acid-fume dust, where the conductivity is imparted to the dust particles by coming into contact with the acid fumes, the temperature is of importance.

Jan 8, 1925

By Carl D. Wood

Traditionally, when one considers the optimization of a flotation circuit, the scope of work focuses on a review of unit process equipment. This usually includes topics such as grinding ball typed, grind size, classifier efficiency, mill liner design, chemical reagent addition rates, alternative chemical reagents, on-line process analysis, and automated control strategy. However, since very few companies can afford the capital expenditure needed to completely automate the processes, the flotation operator remains as a critical link in optimization of the circuit. Therefore, upgrading of operator skills and knowledge through training must be considered as equally as important as unit process review. This paper will review some concepts and approaches to innovative operator training. INTRODUCTION Consider for a moment the fantastic changes that have occurred in process automation at many flotation plants during the last several years. Flowmeters, density gages, and on-stream analyzers now routinely measure process conditions and effect control strategy. These functions had until recently been entrusted to human flotation operators. Now with a little stretching of the imagination it is possible to envision a plant where very little human intervention would be required. However, when one begins to calculate the capital cost required to fully install automatic equipment, it quickly becomes apparent that many parts of flotation plants will continue to require skilled, knowledgeable operators to ensure successful operation. Additionally as these automatic systems are put into place, the operator's duties become increasingly complex. Therefore no flotation plant can be considered optimized without upgrading each operator's skill and knowledge to match the technology utilized. BACKGROUND At Henderson, one of the hardest steps towards the optimization of operators was to realize that present level of operator skill and knowledge was not sufficient. Since Henderson had a track record of producing the highest quality molybdenum concentrate in the world, it was difficult to accept the idea that change was needed, or even possible. This realization came about as Henderson began a program to modernize the cleaner plant circuit. Henderson utilizes a complex cleaner flotation circuit involving multiple stages of flotation, with a counter- current routing of flotation tailings. Since start-up in 1976 Henderson had relied upon next-day laboratory analysis techniques, that provided an after the fact measurement of process. Hour to hour process control was implemented by the operator, the basis for the operators' control decisions was primarily the individual operator's experience and "feel'. Bench marking of current flotation technology indicated that on-stream analysis was a proven state-of-the-art method for improving process control. An Outokumpu Courier 30 analyzer was purchased and installed to provide real-time analysis of critical cleaner plant flows. The analyzer quickly began to provide valuable assay information, allowing the metallurgists to develop specific target values for important flotation variables. However due to the complexity of the circuit, the analyzer information showed that a problem was usually caused when several targeted parameters went out of range simultaneously. This made it difficult for the operator to determine just where to implement the proper corrective action. It became apparent that to take full advantage of the new analyzer information each operator would have to become proficient at understanding the material balance of the entire circuit. TRAINING PLAN CONCEPTS With the goal of giving each operator a working knowledge of a circuit material balance the following concepts were applied to develop a training plan: - Most operators were high school graduates, but had fairly weak mathematical skills, and had very little experience at metallurgical calculations. - The training would have to address a wide range of topics from basic fundamentals to complex material balance. The basic sequence decided upon, was to present a fundamental topic to the entire group, break into small groups to work a “hands on'”case study example of that topic, and design the case study results so that they could be combined to highlight a major portion of the material balance concept.

Jan 1, 1993

By William F. Tanner

A river delivers a given load of sand, and hence of heavy minerals, into the sea into which it empties. This load is fixed by drainage basin characteristics and processes. Wave energy available for redistributing that load is fixed in an entirely different way. An equilibrium diagram of these two parameters (load versus energy) permits a tentative prediction of what will happen to the heavy minerals. The Chattahoochee River delivers a load which, over the past few thousand years, appears to have been greater than the available coastal energy could handle. As a result, much of the sand has been accumulated in various delta-margin features: barrier islands, beach ridges, and large furrowed off-shore shoals. The bulk of the trapped sand is found today in the shoals, which are attractive deposits for possible exploitation. If coastal energy levels are high enough to move the total load delivered by the river, accumulations of sand (and hence of heavy minerals) should be sought in the down-drift direction. Energy levels are rarely constant over any great length of coast. Decreases in energy may be due to widening of the shelf, convexity of, the shore, restrictions on the fetch, wave decay, or other causes. Such decreases result In deposition. Hydrodynamic mapping of coastal areas, as outlined here, should prove useful in the location of additional reserves. Part of this type of work can be done on maps, charts, and air photos.

Jan 1, 1962

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

The value creation with kaolin clays depends on removing the colored impurities which manifests in to higher brightnessone of the most sought after properties on applications such as paper coating, paint and others. The processes for removing impurities include magnetic separation, froth flotation and selective flocculation. While the flotation and selective flocculation processes exploit the physico-chemical differences between the surface properties, the magnetic separation uses the bulk magnetic susceptibility differences between the diamagnetic clay and ferro- and para-magnetic nature of the impurities. The major advantage with magnetic separation remains high yield and no or low reagent usage. However, the magnetic separation technology suffers from low separation efficacy when finer colored impurities (<1 µm) are encountered in the feed. Use of stronger magnetic intensities during magnetic separation showed limited success; nonetheless the adverse effect due to finer size range remains a dominant effect even at 5 Tesla magnetic field. Furthermore, the presence of diamagnetic colored impurities irrespective of their sizes can not be removed. Cytec Industries has recently developed a ?bolt-on? chemical enhancement technology for magnetic separation that essentially embraces the best product performance attributes of flotation and selective flocculation while keeping the chemical usage to a minimum level and using the readily available magnetic separation equipment. The paper will outline the technology and illustrate optimization work at pilot plant magnet on a wide variety of crude accommodating the process needs and plant limitations. The major advantages of chemical enhancement technology to magnetic separation include: 1) simple extension to existing magnetic separation technology, 2) ability to produce comparable product in quality with cost effectiveness compared to flotation and selective flocculation, 3) removal of impurity minerals over wide size range, 4) removing non-magnetic impurities, 5) providing robust process with high process yield and 6) operation-friendly nature. Furthermore, chemical enhancement technology for magnetic separation has also emerged as a platform for re-moving impurities at low levels in other mineral systems as well.

Jan 1, 2014

By R. V. Ramani

An improved mine environment is the single most critical factor affecting the health and safety of workers engaged in underground coal winning. A very important subclassification of this wide field is mine ventilation, which essentially deals with &apos;mine atmospheric environmental control.&apos; To ensure proper mine atmospheric environmental control, adequate quantities of air must flow through working sections in the mine. In recent years much attention has been paid to the fan and its prime movers, but the efficient use of the fan output in the workings has not received an equal amount of investigation. In mechanically ventilated mines friction losses in main airways often account for 70 to 90 percent of the total pressure loss sustained in the system. Also the leakage losses are a serious detriment to the efficiency of mine ventilation systems. It is not uncommon to loose 60 to 70 percent of the air between the fan and the last open cross-cuts due to leakage directly into the return Proper assessment of these losses in simulating and projecting complex ventilation systems is vital. Network analysis of ventilation systems is not new. Scott and Hinsly (1951) presented the detailed mathematical framework. Since then work has been done in adopting this technique to analog, and within the past few years, to digital computers. Development of computer programs to solve ventilation network problems has been reported in United Kingdom, Japan, U.S.S.R., South Africa, Germany, and the United States. The purpose of these programs is to serve as an experimental mine wherein analysis of proposed alternatives or ventilation planning can be tested. The great power of the computer as a planning tool lies in the ability to input empirical or Projected data into programs with predicting ability. But, however good a computer program is, unless fairly accurate input information is available accurately assessing the engineering factors of the ventilation system, the output will be suspect. Thus, to simulate and project mine ventilation systems, good estimates of leakage and friction factors are important. Yet, relatively little work has been done in the past three decades to determine these more realistically.

Jan 1, 1973

AN economist at MIT provided Americans with myth destroying information which should prove effective against the gentlemen of the extreme left. For a number of years they have charged that a small number of companies in each industry has been grabbing more and more of the industry&apos;s business. M. A. Adelman has shown that the concentration of business in the hands of big corporations has not shown any sign of growth during the last 50 years. Quite the contrary, there has been a slight decline in this concentration, according to Adelman. There are more small companies per thousand population than ever before. Bearing this out is the fact that International Harvester is now doing 41 pct of the possible market against a former 85 pct; American Can Co. has dropped from 90 pct to 50 pct; American Smelting is down to 31 pct compared with 90 pct; and lastly, U. S. Steel which has plummeted from 65 pct to slightly more than 30 pct of the steel market. Declines of the same proportions have hit big companies in other industries. Price cuts on Detroit&apos;s 1953 automobiles indicate that even among the biggest competition is still one of the most important household gods. Big business is still slugging it out for the attention of the American consumer. It&apos;s a battle which can only have one result-benefit to the man who buys.

Jan 1, 1953

By Hubert E. Risser

At the outset of a discussion on the adaptability of Illinois coals for use in iron and steel production, it is perhaps well to define terms. ?Adaptability? as used in this context, means that a coal can be, adapted to use within a given technological and economic framework. For a coal to be adaptable, to use in the manufacture of metallurgical coke within the present technological and economic framework, it must possess, among other things, at least the following characteristics: 1. The coal must be capable of producing, alone or in combination with other coals, a coke that can meet at least a minimum standard of required performance in the present-day blast furnace. The coke must have sufficient strength, stability, hardness, and freedom from impurities to make it suitable. 2. If the coal in its raw form does not meet these requirements, it must be amenable to beneficiation or upgrading so that the requirements can be met. 3. It must be available in uniform quality and in sufficient quantities to meet the need. 4. Use of the coal must be economically attractive. If its quality is equivalent; to that of the coals with which it must compete, it must be no more expensive than they. If It is better, a premium price may perhaps be demanded. If, in any respect, it is the least bit less suitable, the cost must be lower to offset its disadvantages.

Jan 1, 1961

By H. L. Hopkins, L. W. Kempf

Aluminum alloys, in common with most other metallic alloys exhibit slight density changes with variations in temper achieved by heat-treatment, which usually are the result of the variation with temperature of the solid solubility of the various alloy constituents in the solvent metal. Changes in density are, of course, most marked in conditions that exhibit the maximum variation in solid solubility of the constituents. In aluminum alloys these conditions usually prevail when alloys are quenched from just below the melting point and are subsequently reheated to some lower temperature. Since commercial heat-treatments may be of this type, the density changes, although small (of the order of 0.3 per cent which may be compared with the density change of about 1.5 per cent involved in the transformation, at ordinary temperatures, of gamma to alpha iron during the hardening of steel), may in some specific applications necessitate quantitative consideration. This phenomenon has been investigated extensively in the laboratories of the Aluminum Company of America over a period of years. A number of investigators &apos;-5t have observed and measured the density changes accompanying the heat-treatment of aluminum alloys. In general, these changes have not been directly translated to dimensional changes and their significance has been overlooked to some extent by the practical user of aluminum alloys. It is the purpose of this paper to consider some practical aspects of these density and dimensional changes. These density changes were given some consideration in 1917 in connection with the use of aluminum-alloy pistons for aircraft engines. Investigations by Lea and Shakespear were reported in some confidential reports of the British Advisory Committee for Aeronautics, Light Alloys Subcommittee, during 1917 and 1918, which are not generally available in published form. In these reports the term "permanent growth" was applied to the dimensional changes occurring in the pistons at the tem-

Jan 1, 1936

By Lindbeck K

The mining industry in Western Australia is a large sector of the WA economy providing $12 billion (1993) of the export income for the State. Historically, mining in WA developed from traditional prospecting in the late-1880s leading to major underground operations by the turn of the century. Large open pits were developed in WA following World War II and became increasingly common since the gold boom of the 1980s. With the development of the open pits has been concomitant evolution of mining legislation, principally the Mining Acts of 1904 and 1978, which has been also accompanied by a practical evolution of the administrative system within the Department of Minerals and Energy. The mining industry has recognised the need for sound environmental management at mine sites, taking up the challenge and becoming a world leader in rehabilitation techniques. Any environmental management program in the industry has three stages: approval by government; management by the industry; and return to the State in an environmentally acceptable condition. The WA environmental requirements, procedures and industry performance in these three stages are discussed.

Jan 1, 1994

The mining of mineral sands in coastal aquifers is often constrained by other land use conflicts and inappropriate controls imposed through a lack of understanding of environmental interactions and processes. The recent experience with the Tea Gardens mining operation illustrates how increasing our knowledge and understanding leads to more effective management of environmental problems. As well as a source of heavy minerals, the Tea Gardens sand bed serves as a town water supply source. From past experience it was believed that mining could cause undesirable increases in dissolved iron concentrations in the aquifer, but the reasons and mechanisms for this phenomenon were not clear. A water monitoring program was therefore designed for the mining operation which was aimed at protecting the water supply borefield from any detremental effects. After one year the results of the monitoring program were assessed in the light of new knowledge and understanding of iron hydrochemistry. It was found that the existing program was not achieving some of its major aims, and was therefore modified to a more effective and cost efficient program.

Jan 1, 1988

By Md. Rashedul Islam

Magnetic data was collected from the Yeoju historical sites using the fluxgate gradiometer through six sites & several grids. We measured the vertical gradient by the FM256 Fluxgate gradiometer. The readings were logged every half meter. The obtained data were processed and treated to introduce a high quality magnetic image. The gradiometer results defined various positive and negative magnetic anomalies, which revealed the existence of several archaeological features of different shapes and sizes. The study of the process magnetic images give us a concept that the subsurface features are caved shape stone chamber tombs, burial mounds, deep room structure, Yeoju mausoleum, pagoda?s square foundation stones, walls etc. All these are superior work of early Goguryeo inheriting orthodox Silla style. So, the study area may have great archeological interest.

May 1, 2009

In reviewing recent developments in the process mineralogy of gold it is convenient to distinguish between visible (>0.1 pm) and invisible gold (1 - 2 pm in size in polished section; these can scan the surface of a polished section, identifying the gold minerals, recording co-ordinates of the grains for subsequent examination, and making measurements of areas and sizes of the grains. However, problems of sample reliresentivity in polished section mean that such data may not give good quantification of gold mineral proportions and liberation/locking characteristics and other methods are required for this (amalgamation, cyanidation, ultra-fine milling and cyanidation). Characterisation of invisible gold in bulk material (eg a sulphide concentrate) can be done by mineral separation, ultra-fine milling and cyanidation or by quantitative point analyses of a large number of mineral grains. Analytical methods include electron microprobe analysis (detection limit normally -200 ppm but -10 ppm by using special techniques), ion microprobe analysis (secondary ion mass spectrometry - SIMS; detection limit -0.2 ppm) or proton microprobe analysis (PIXE; detection limit

Jan 1, 1992

By Clifford J. Roblee

In this paper, various seismic indicators are evaluated for ability to discern fractures induced into a rock mass by blasting. This is accomplished by presenting results from in situ crosshole seismic studies performed prior to and after a sequence of controlled blasts within limestone and dolomite rock near Austin, TX. Indicators investigated are compression (P-) and shear (S-) wave travel times, first peak and maximum amplitudes, first arrival rise rate, and the linear spectrum of the received signal. Compression wave travel time yielded the most consistent results, while the various amplitude indicators yielded the poorest results for the equipment configuration utilized. In addition, this study documents magnitudes of change in seismic measurements which occurred following blasting. Both P- and S-wave travel times exhibited a wide range of variation due to blasting. Near blast centers below the surficial fractured rock, velocity decreases of about 10% were noted, significantly less than the 50% decrease observed for previously fractured near-surface rock through which the explosive energy was vented. Signal amplitude measurements also varied in magnitude but were less consistent.

Jan 1, 1989

By J. R. Patts, A. B. Cecala

"After industrial sand has been mined and processed, the finished product is typically loaded into small bags of 45 kg (100 lb) or less, large bulk bags of 454 to 1,361 kg (1,000 to 3,000 lb), or vehicles such as trucks or trains for transport to end users. As the sand is being transferred and loaded, dust can be released into the work environment, potentially exposing workers to respirable crystalline silica. A number of control technologies have been developed and utilized in an effort to reduce dust liberation during loading operations. For bulk loading into trucks or trains, the U.S. National Institute for Occupational Safety and Health (NIOSH) evaluated one of these technologies, the Dust Suppression Hopper (DSH), at two industrial sand processing plants. Results from these case studies show that the DSH reduced airborne respirable dust levels by 39 to 88 percent, depending upon the product size being loaded.IntroductionInhalation of respirable crystalline silica dust can lead to the development of silicosis, a disabling and potentially fatal lung disease. Once contracted, there is no cure for silicosis, so the goal is to prevent the development of the disease by limiting exposure to respirable dust containing crystalline silica at or below the exposure limit of 50 µg/ m3 recommended by the U.S. National Institute for Occupational Safety and Health (NIOSH, 2002). At industrial silica sand operations, the product contains high levels of crystalline silica, so effective control technologies are needed to minimize the respirable dust exposure of workers.NIOSH, in partnership with the Industrial Minerals Association–North America, published a dust control handbook (NIOSH, 2012) focused upon control technologies for industrial- mineral mining and processing operations. One chapter in this handbook discussed technologies for controlling dust liberated during bulk loading, including telescoping loading spouts, dust collection systems for loading spouts, enclosures for load-out areas and a newer technology known as Dust Suppression Hopper (DSH)."

Jan 9, 2018

By F. H. Deily

The petroleum industry has developed and utilized many aspects of rock mechanics, both in its search for petroleum and in its drilling and production operations. Geological exploration activities have been improved by knowledge of earth tectonic forces. Better understanding of seismic wave motion has contributed to a more accurate interpretation of geophysical data. Drilling activities have benefited from basic knowledge of rock strength behavior under in situ conditions. Production has been significantly increased through stimulation techniques, such as hydraulic fracturing. The ability of rock mechanics work to contribute to future petroleum activities will depend upon the development of knowledge of rock properties under greater depths and at higher pressures and temperatures.

Jan 1, 1969