Search Documents

By Juh W. Chen

A process for recovery of energy from waste coal fines was investigated. The process, which was developed through laboratory, bench, and pilot plant scale experiments, consists of mechanical cleaning followed by high temperature oil agglomeration and pelletization. The process can produce a quality product under an economically and environmentally acceptable condition. Waste coal fines with ash less than 35: and HHV greater than 6,000 BTU/1b have been upgraded to a product with less than 15% ash and HHV Greater than 11,500 BTU/lb. A computer model has been developed to optimize the processing costs and to perform economic evaluation of specific sites. Ultimately tine model can be utilized to establish a priority listing for a region in assisting the determination of reclamation strategy.

Jan 1, 1983

By A. Pearson, F. A. Auld, S. O. Colbeck

"""The theory of buckling of shafts and Steel tunnel-linings"" was published by E. Amstutz in 1970 and commented on by S. Jacobsen in 1974. The authors have revised and enhanced Amstutz’s work to address Jacobsen's comments on its limitations and to extend its validity over a wider range of pipe/shaft geometries, including those commonly found in deep mine access shafts. The author has looked at Amstutz’s assessment of strengthening with flexible shear anchorages and adapted the theory of non-linear shear deformation response of bolts to develop a method of assessing increased buckling capacity utilising the full plastic shear capacity of studs. INTRODUCTION “Amstutz Buckling” refers to the buckling of pipe embedded in concrete under external uniform pressure. In terms of a mining environment, this relates directly to the design of a watertight shaft. This load case will commonly occur where a main shaft is cast against a geostatically stable primary liner and the only load applied to the final shaft is that of a uniform ground water load. Ernst Amstutz wrote his first paper on buckling of pressure-shaft steel linings in 1950 and subsequently improved his theory (Amstutz, 1970), which was then widely adopted for use within the industry. Years later, an alternative approach (Jacobsen, 1974) was proposed. Within his paper Jacobsen critiques Amstutz work, identifying some mathematical inconsistencies and highlighting limitations of the theory imposed by approximations adopted by Amstutz. Despite these limitations Amstutz work has still been used as the favoured design theory for use in the mining industry. In reviewing this body of work the author realised that with the advent of readily available computing software it was possible to adopt an iterative approach using Amstutz approximate formulae to find a solution to the original precise formulae, thus eliminating the limitations highlighted by Jacobsen The shear deformation to load characteristics of bolts has long been established (Crawford & Kulak 1968) and used for the plastic design of bolted connections in shear. This relationship is directly transferable to the design of shear studs, typical properties are well known, and actual values easily established in simple lab tests. The author has taken this relationship and modified Amstutz theory (Amstutz, 1970) for shear anchored strengthened liner buckling, to give a more efficient solution, using readily available material properties."

Jan 1, 2019

By H. F. Korman, M. C. C. Mow, P. K. Dai

INTRODUCTION Detonations of high explosives in soil and rock have been used frequently in civil engineering applications. Of particular interest in recent years has been the development of test methods to simulate the desired blast and shock environments for the testing of protective structures. The United States Air Force, in particular, the Air Force Weapons Laboratory, in conjunction with the Defense Atomic Support Agency, has in recent years, developed special technology for simulation testing of protective structures in soil and rock media. Such a technology, although initially developed for military applications, is rapidly finding its way into civil applications. One of the major problems in the design of the simulation test is the correct prediction of ground motion induced by the detonation of high explosives. This paper presents a useful prediction method which is developed specifically for ground motion in rock that is induced by the detonation of a buried planar array of explosive columns (See Figure 1). The technique of simulating shock environment using such an array is called the Direct Induced High Explosive Simulation Tech- nique (DIHEST). Normally, each shot hole may contain canisters of ammonium nitrate positioned at various depths, or a slurry explosive with detonators positioned along its length (See Figure 1). The depth and width of the array, the spacing of shot holes, the spacing of detonators, the degree of containment, and the charge weight are the variables which govern the induced ground motion

Jan 1, 1971

By A. K. Suri

India plans to increase the nuclear power share in overall energy-mix to about 30% by 2032 using both indigenous and imported reactor technologies. In the immediate time-frame, it is envisaged to generate 10000 MW electricity by PHWR technology by 2020 using indigenous uranium resources. This necessitates setting-up of new uranium mills and augmenting the existing resource, mining and milling capacities. This paper describes the current status and future R & D needs towards achieving the targeted demand of yellow-cake. Keywords: uranium, hydrometallurgy, leaching, yellow cake

Sep 1, 2012

He was born at Montreal, Canada, in 1875. His earliest education was received in Montreal hut was continued from 1885 to 1892 at schools and academies in Brooklyn, Whitestone, and Flushing, L. I. For his technical education he returned to McGill University, where he graduated in 1897. His first professional occupation was as transitman enga.ged in the running of township lines in the Rainy River District of Ontario. In 1899, he was made assistant chemist at the Cuggenheim smelter at Aguascalientes, Mexico. From 1900 to 1903, he was chief chemist for La Compañia Minera de Peñoles, at Mapimi, Durango. We have no information as to his pursuits during the next eight years, but from 1911 until 1914, when he became a member of the Institute, he was chief engineer for the Bankhead mines in Alberta, Canada. Lieutenant-Colonel Alfred Winter Evans Lieutenant-Colonel Evans, who was in command of the Third Battalion of the New Zealand Rifle Brigade, and had been cited in Distinguished Service Orders and received the Distinguished Conduct Medal, was killed in action on Oct. 12, 1917. Alfred Winter Evans was born in Natal, South Africa, in 1881, and received his preliminary education in the Durban High School. For the next five years he attended St. George's School at Harpenden Heights, England, until 1898. Returning to South Africa, he worked . for three months of 1898 as underground sampler for the Crown Deep Gold Mining Co., at Johannesburg, and for six months of the following year he was shift-boss for the Crown Deep, Ltd. At the outbreak of the Boer War he took an active part and was engaged on military service from 1899 to 1902. At the close of the mar, he came to New York and attended the Columbia School of Mines, where he graduated with the degree of E. M. in 1906. A part of that year he spent as assayer to a mining company at Poland, Arizona. In 1907, he returned to South Africa and engaged as underground contractor in charge of mining and development at a number of the South African mines, notably the French-Rand, the ViIIage Main Reef, the City Deep, and others. In 1908, he acted as shift-boss for the Fer-rerra Gold Mining Co. at Johannesburg. In 1909, he was appointed acting general manager for the Consolidated Goldfields of New Zealand,

Jan 1, 1920

By C. R. Royal, B. E. Friedland

Energy & Densification Systems (EDS) has developed patented new technology crushing/milling equipment. The EDS Multishaft Mill is a compact vertical mill – utilising high-speed impacts to break down particles with large reduction ratios, low energy consumption and improved liberation. The milling action combines several processes to provide a multitude of output products to satisfy various specifications. Comminution often accounts for more than 60% of the total power consumption on a mine. Two of the key problems to be solved in comminution is to bring down the specific energy required to reduce particle sizes; and to improve liberation or improve the efficiency of the beneficiation and recovery of the required elements. The EDS Mill has shown extensive improvements in both these areas with energy efficiencies up to 75% better than conventional milling equipment and improving liberation beyond the standard beneficiation processes. Conventional comminution equipment requires massive, heavy parts to be moved or rotated, consuming a lot of energy in doing so and not inputting that energy into the breakage of particles. In the EDS Mill, ramping up the relatively small shafts to speed is all that is required. Once at speed, the momentum, together with the minimal amount of constant drive required, means that the energy can be transmitted directly and efficiently into breaking down the particles. The high-speed impacts allow for a shattering effect of the particles and this quickly generates a high ratio of fines. Furthermore, the single impact force breaks particles in a very different manner to conventional compressive force breakage. With compressive force breakage, the particle breaks from point to point. With high-speed impact force breakage, the force tends to migrate through the weakest areas of the particle, which tend to be the mineral boundaries. This, therefore, means that when the particles break, the various minerals are exposed and hence liberated. Keywords: Comminution, high-speed impact, liberation, energy efficiency, novel comminution

Jan 1, 2020

As part of the overall development of a borehole mining system -develop backfilling techniques to reduce possible damage to the environment caused by either the cavities or the piles of sand tailings that result from in-borehole hydraulic mining. (Borehole mining is described in technology News No. 56.) Approach Water filled cavities at the bottom of boreholes are rapidly and economically backfilled by jetting a sand-tailings slurry underwater. How It Works The Bureau of Mines borehole mining system creates a cavity having a horizontal diameter of more than 50 feet. (See photograph). This cavity can be backfilled with much of the sand previously mined. The sand tailings or similar backfill material is dumped by a front end loader into a slurry mixing tank at the rate of about one ton every three minutes. Enough water is added to give a thick, but pumpable slurry. The slurry is pumped down the borehole through a string of 4-inch pipe to the cavity. After passing through a right elbow at the end of the pipe, the slurry is ejected through a nozzle. The resulting slurry jet emplaces the backfill at the outer wall of the cavity. To obtain an even distribution of fill in the cavity, the nozzle is slowly rotated. The nozzle and pipe assembly is supported from a turntable on the surface. See diagram.

Jan 1, 1981

By Lumley G, Rowlands D

The overburden slusher (OS) is proposed as a stripping tool that is expected to find application in overburden stripping operations including open cut coal and oil shale mines. OS is expected to combat the effects of increasing depth on the productivity of conventional dragline stripping.Although previously developed stripping techniques have included the use of drag scrapers the OS is sufficiently different as to constitute a new stripping method.A study undertaken at the University of Queensland during 1985 is believed to be the first major study on the use of the OS and preliminary economic results are very encouraging. It appears that the OS has the capacity to remove overburden at a cheaper unit cost than the equivalent powered dragline stripping machine at any comparable depth of overburden. The OS is not adversely affected by increasing stripping depth to the same extent as a dragline. In addition, the action of the OS machine allows for the lowering of spoil face angles, thereby reducing spoil slope stability problems encountered in deep open cut strip mines.

Jan 1, 1986

The first principle one usually Learns about blasting is that cunpetence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced blaster when operating in a new area, may have to make one or two shots just to acclimate himself to the new conditions with which he is faced.

Jan 1, 1989

By P. R. Clifford

Phosphogypsum is a byproduct of the manufacture phosphoric acid. There are approximately one billion tons of phosphogypsum stored in stacks in northern and central Florida. The Florida Institute of Phosphate Research (FIPR) is investigating potential uses of phosphogypsum. These include using phosphogypsum as a road base material, as a soil amendment in agriculture, as a daily cover in landfills, and as a construction material. The results of this research will be presented and will be discussed in light of regulatory barriers to the use of phosphogypsum.

Jan 1, 2002

By Wai Wu, C. Haycocks

The majority of Appalachian coal deposits lie in a multi-seam environment. Historically, the decision to extract a particular seam has been based on ease of access, ownership and economics rather than ground control considerations. As mining progresses and seams are being mined out, it is increasingly common to find working and abandoned mines in close vertical proximity to each other. Such contiguous operations can produce both positive and negative ground control situations in neighboring seams. These ground control problems, defined as interaction problems, are frequently reported, and their severity can range from minor roof problems that may require no additional support to complete loss of a large section of coal reserves (Stemple, 1955; Peng & Chandra, 1980; Haycocks & Karmis, 1983; Su et al, 1984). As a consequence, interaction problems are of growing concern to the Appalachian underground coal industry. Although interaction problems in multi-seam mining have been recognized for many years and many investigations have been conducted to study the problems, the ground control principles involved in their development are only partially understood. Previous research has identified four interaction mechanisms: pillar load transfer, innerburden shearing, arching effects and upper seam subsidence (Haycocks et al, 1982; Haycocks & Karmis, 1983). Pillar load transfer mechanisms and innerburden shearing have been successfuly used to explain interaction phenomena associated with undermining operations, while arching and subsidence have been used to assess problems during overmining. In addition, interaction-controlling factors such as cover, innerburden and seam thicknesses, extraction percentages on both seams, time delay between operations on two seams, and characteristics of innerburden rock have been identified and utilized in evaluation of interaction effects (Haycocks & Karmis, 1983; Webster et a1.,1984). As an example, Figure 1 shows the relation of innerburden layering and thickness to interaction on the lower seam. The combination of such theoretical work and the analysis of case study information has made it possible to determine, with a certain degree of confidence, the interaction damage in undermining conditions. The results of such an approach have been sufficiently successful and complete to be incorporated into a software package to assist field engineers in estimating potential interaction effects when undermining a previously mined upper seam (Grenoble et al, 1984; Grenoble & Haycocks, 1985; Grenoble et al, 1985). Although the conventional finite element and photoelastic modeling techniques have been

Jan 1, 1986

By Harold D. Taylor

Cone fitting is a procedure which can be used to estimate the short range, linear portion of a variogram. Rather than combining data over windows In different directions and fitting by hand, cone fitting estimates the variogram in all directions at once using a multiple regression approach. The method automatically provides estimates of nugget effect, anisotropy, and initial slope of the variogram. This paper presents the results of simulation studies which have been carried out. These studies Indicate that the method works well and that it may be particularly useful for small data sets. The simulation studies also indicate that the local variogram may differ greatly from the theoretical variogram.

Jan 1, 1986

By E Villaescusa

This paper describes a methodology for the design of mine pillars at the McArthur River Mine. The pillar strength is calculated using a method that accounts for confinement, pillar geometry and intact rock properties. The average pillar stress was calculated using in situ measurements of vertical stresses at shallow depth and the tributary area method in conjunction with numerical modelling. Observations of pillar behaviour indicate that an existing pillar stability graph may be slightly conservative and further adjustments for the local rockmass conditions are needed. The results to-date indicate that all mine pillars are stable for a range of mining geometries at McArthur River Mine.

Jan 1, 1998

By Brian Kenner, Peter Swanson, Todd Krahenbuhl

NIOSH has developed an automated PC-based seismic event (induced earthquake) monitoring, system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network is a central feature of the system. Mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface. Seismic event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system's design philosophy, hardware and software components, examples of installations, and a few observational results.

Jan 1, 2002

By Brian Kenner, Peter Swanson, Todd Krahenbuhl

NIOSH has developed an automated PC-based seismic event (induced earthquake) monitoring system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network is a central feature of the system. Mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface. Seismic event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system’s design philosophy, hardware and software components, examples of installations, and a few observational results.

By C. Cutts, K. Wheatley

The Dragon Lake Zone (uranium prospect) comprises a N160º trending vein that is approximately 110 m long, up to 5 m wide and from 1 to 40 m high. The zone is mostly within altered sandstone of the Fair Point Formation, the basal unit of the Paleoproterozoic Athabasca Group, but it also extends downward (up to 3.5 m) into basement rocks that occupy the northerly trending Maybelle River Shear Zone (MRSZ). This subvertical shear zone separates graphitic paragneiss and weakly deformed granitoid rocks to the east from non-graphitic paragneiss and foliated granitoid rocks to the west. The Dragon Lake Zone cuts across both the MRSZ and N060º-N070º-trending cross-faults that offset the shear zone but not the mineralized vein, which contains values up to 54.5% U over 50 cm core length. Strong chloritization occurs in graphitic paragneiss and sandstone adjacent to mineralization. Silica was depleted from the basement rocks and redeposited at the borders of the 5-15-m-wide alteration zone, as well as within overlying sandstone of the Manitou Falls Formation. There are minimal alteration effects in the overlying Lazenby Lake Formation. Geochemistry shows that the alteration zone in the Fair Point Formation is highly anomalous in metals, most notably in Ni, As, U, Pb, Co, and B. Clay within this zone is illitic and Fe-rich chlorite is also present. Brittle deformation is not as widespread or as well developed in the Fair Point Formation as it is in the overlying Manitou Falls Formation, which is extensively brecciated and contains some anomalous metal values.

Jan 1, 2013

By Alan R. Buehler

A mineral survey of the 67, 110-acre Raven?s Eye WSA (Wilderness Study Area) in the north-central Snake River Plain of Idaho was conducted by the U.S. Bureau of Mines in 1985, at the request of the Bureau of Land Management. The WSA is in Blaine and Lincoln Counties; the northwest corner is about 1 mile east of Carey, 10. A search of county mining claim records indicated that no claims have been located in the WSA. Basaltic lava is the only rock type exposed within the WSA. A platy variety of lava (slab pahoehoe) occurs that is produced from other lava fields in southern Idaho. The material is marketed as decorative stone, used for wall veneers, and retails for approximately $125/ton. Within the W5A, approximately 18,000 tons of indicated reserves are concentrated in two areas, and a total of 12,000 tons of indicated subeconomic resources were found at six other localities. An additional 10,000 tons of inferred subeconomic resources are unevenly distributed over the remainder of the WSA.

Jan 1, 1986

By Tracy Brettmann

A new method for estimating ground vibrations caused by pile driving was developed as a result of a vibration monitoring program performed for a large pile driving project. The method is accurate, rational and theoretically based starting with energy actually transmitted to the pile (not the rated or operating hammer energy). This energy is then assumed to be transmitted to the soil in the form of surface waves that attenuate from both geometric and material damping. The main input parameters for this method include the energy transmitted to the pile and the dynamic properties of the soil (wave velocity, material damping, and unit weight). In this study we concurrently measured both: (1) pile driving of 14-in.-square, 65-ft-long precast concrete piles with a Pile Driving Analyzer?, and (2) vibration levels at various distances away from the piles during driving. A geotechnical study for the site was also performed that included measurement of the dynamic soil properties using both crosshole and seismic cone testing. This paper presents the data obtained from the study and compares the results to the values estimated using this new method. Vibrations from pile driving is a serious matter that impacts virtually every pile driving project. It is important that accurate methods for estimating ground vibrations be available to engineers and contractors.

Jan 1, 1999

By Henry E. Perlee

In a Bureau of Mines study two-dimensional mathematical equations were solved that describe the transient thermal response of a rock dust particle in a cloud of similar particles in a gas flame's preheat zone subject to a radiant field from the approaching flame. The description includes both radiant energy absorbed and emitted by the particle and thermal conduction inside the particle and into the surrounding gas environment moving relative to the particle. Two situations were studied; in one the radiant energy incident on the particle is converted to thermal energy at the particle surface, and in the other the radiant energy is converted to thermal energy uniformly over the volume of the particle. The result of the study showed that for a 10-µm-radius particle, a 200-mg 1-1 loading density, and a flame approach velocity of 30 m sec-1, the particle temperature rise was twice that previously calculated by Singer and Cook based on the model of Essenhigh and Csaba. It was further established that under the conditions examined a rock dust particle temperature never increases more than about 200 K before crossing the flame front.

Jan 1, 1976

Of the many organic impurities present in Bayer liquor, sodium oxalate is known to have one of the most detrimental effects on the Bayer process. Because of its limited solubility, it will co-precipitate with gibbsite during the precipitation stage which results in many operational challenges for the refinery. Despite the importance of this phenomenon, the interaction mechanism between gibbsite and sodium oxalate is not well understood. In this study, the growth of sodium oxalate on three main morphologies (random agglomerates, prims and hexagons) of water-washed and caustic-washed gibbsite was observed under synthetic Bayer conditions using in situ optical microscopy. After a short induction period, oxalate started to nucleate on gibbsite crystals, and grew with a needle-shaped morphology which eventually developed into oxalate bundles. In addition, the results indicated that caustic washing was able to partly decompose gibbsite crystals and thus make the gibbsite surface rougher, which provides more potential sites for oxalate nucleation and growth. The growth rate of oxalate crystals on the basal (001) face of water-washed gibbsite was 1.33 µm/min determined by the time-lapse imaging of in situ optical microscope.

Jan 1, 2014