Search Documents

By Alan Diaz Butron, Eng. Thierry Bernard

"In tunnel blasting the most challenging objective is definitively obtaining the maximum advanceassociated to a minimum overbreak. Achieving 100% of advance with no overbreak is the targetchallenge by Chavimochic Consortium. Chavimochic Special Project is an irrigation system that extends throughout much of the coast of the La Libertad Region, on the north coast of Peru. In 2012, it began management for construction of the third and last stage of CHAVIMOCHIC to irrigate lands of Chicama Valley, North of Trujillo. This project of 13 Km (8 mi) of various tunnels, it's a combination of technology and daily optimization by experienced people, which allow to accomplish the objective. Achieving this advance with no overbreak provide a huge saving on time. This paper describes the method, technology used, and the results obtained on more than 600 blasts done with conventional initiation system on the first 3 km (1.86 mi)."

Jan 1, 2017

By G. Macfarlane

"In 1985, a crushing plant, located in the feed preparation area of Kidd Creek's copper smelter, was modified. The plant, which originally had treated only copper-bearing materials for the smeller, at a rate of 10 tonnes per hour, was expanded to 40 tonnes per hour capacity and modified to treat silica ores to meet the smelter’s flux requirement and also gold ores from the company's Hoyle Pond property. In the storage area adjacent to the crushing plant a 300 tonne per day gold mill was constructed.This paper outlines the construction and first year of operation of the crushing plant and gold mill with emphasis placed on the capital and operating advantages to be gained by utilizing an existing metallurgical infrastructure.IntroductionThe Kidd Creek Mines Ltd. copper-zinc-silver orebody is located 24 km north of Timmins, in Northern Ontario . Mining of this massive sulphide de posit commenced in 1966 and, in the ensuing years, a concentrator and zinc plant were constructed at the metallurgical complex, approximately 17 km by rail from the mine site . At this same site, in 1981, a copper smelter and refinery were commissioned. The smelter which utilizes the Mitsubishi smelting process for the continuous production of blister copper from copper concentrate, has been comprehensively described in previous papers.At the time of the smelter construction, a small (10 tonnes per hour) crushing plant was installed in the smelter's feed preparation area. This plant was used to treat the copper-bearing revert material produced by the smelter, and, apart from periods when slags and matte were produced through furnace drainage at the end of each operating campaign, it was generally under-utilized. This fact, together with the requirement to devise a more cost effective method of providing silica flux for the smelting operation, was the basic rationale for modifying and expanding and crushing plan t. At the same time, development at Kidd's Hoyle Pond orebody had progressed to such a stage that a gold mill of 300 tonnes per day was warranted."

Jan 1, 1988

By Scott A. Walker, Gabriel J. Alcantar, Brian Zuckerman, Ramin Golesorkhi

"The stadium development consists of construction of a 68,500-seat, open-air NFL football stadium for the San Francisco 49ers. The main structure will consist of a 7-story above grade steel structure supported by over 3,000 piles. Berkel and Company Contractors, Inc. (Berkel) was selected as the design-build pile contractor who used their auger pressure grouted displacement (APGD) piles for this project. During an indicator pile installation and pile load test program, fifteen piles were tested to develop installation criteria to support demands of 150kips tension and 180 kips compression. Following the indicator pile program Berkel installed 3088 piles in 30 working days. Throughout pile installation data were collected with an automated data acquisition system (DAS). During pile installation field engineers from Treadwell & Rollo observed the pile installation as well as the real-time data from the DAS. Strategic staging and pre-production planning by Berkel along with consistent collaboration with the design team created an atmosphere for a successful and on schedule project completion.IntroductionThe new San Francisco 49ers Stadium in Santa Clara, California will be a 68,500-seat facility, a rendering of which is shown in Figure 1. The main structure will consist of a 7-story above grade steel structure supported by more than 3,000 piles. The north, east and south portions of the stadium are designed as an open seating bowl, while the western portion includes open seating at the lower levels and seven-story tower which houses over 150 suites.The stadium project includes the stadium structure, as well as elevated open pedestrian walkways, commercial community space, and three new pedestrian bridges spanning a nearby by creek. Sustainable designs and innovations such as a green roof, photovoltaic panels, a ground source geothermal system, stadium-wide Wi-Fi capability, and access to public transit are provided throughout the project. The stadium is designed as an open, light, and airy structure and is surrounded by an existing amusement park, office buildings, the Santa Clara Convention Center, and the training facility of the 49ers."

Jan 1, 2015

By S. J. Schatzel, K. M. Ajayi, E. N. Rubinstein, Z. Khademian

This study simulates the impact of a shale gas well casing breach near a longwall mine. Field studies are conducted to measure mining-induced permeability changes over the abutment pillar of a longwall mine, and a geomechanical model is developed in 3DEC, a three-dimensional numerical modeling code, to predict the aperture of fractures in the overburden at the study site. The predicted aperture values are used to determine mining-induced permeabilities and the results are compared with the field measurements. These aperture values are provided as inputs into fracture flow code (FFC), which generates a stochastic discrete fracture network (DFN) model for the study site and predicts the potential shale gas flow to the mine. Results from 100 DFN realizations are statistically analyzed using the bootstrapping method to compensate for notable variation in fracture geometry. The results show a significant difference between the gas inflow for nearby panels due to increase in the induced permeability during mining of the second panel. The average gas flow to the mine was calculated as 4.72×10−2 m3/ s (49 cfm) for a hypothetical breach at the Sewickley horizon during the first panel mining, 8.97×10−3 m3/ s (19 cfm) for a hypothetical breach at the Uniontown horizon during the first panel mining, 2.16×10−1 m3/ s (458 cfm) for a hypothetical breach at the Sewickley horizon during the second panel mining, and 8.07×10−2 m3/ s (171 cfm) for a hypothetical breach at the Uniontown horizon during the second panel mining. Depending on the mine ventilation system, this could result in methane concentrations exceeding regulatory limits. Hence, these findings provide insights into the potential risk of an unconventional gas well casing breach near a longwall mine under shallow cover.

Feb 15, 2023

A systematic study of groundwater conditions at eight underground mine sites exhibiting a wide range of groundwater qualities throughout Australia has been completed at the WA School of Mines. This has resulted in a new corrosivity classification for groundwater driven corrosion processes for cement grouted cable strand used in the Australian underground mining industry. The new corrosivity classification is simple to use and corrosion rates may be predicted from readily obtained in situ measurements of groundwater dissolved oxygen.

Jan 1, 2008

By M. J. R. Morris

THE year 1939 has seen the iron and steel industry driving for efficiency with unabated zeal. "Efficiency" is here used in the sense of enabling the customer to do more with less, either supplying him with more economically priced steels or with higher priced steels that will do a job more economically. The plain carbon steels have been improved tremendously in quality be- cause of recent control tests. All steel companies have been urged to hold to .closer chemical control, closer standards, soundness, and more control on grain size, and now attention is being directed to closer control of hardening properties. Better control of open- hearth operations undoubtedly will result in an increase in the application of special carbon steel. Further, with a better understanding of quenching, the present trend to study the quenching of this class of steels will be ex- tended. These steels will then be used for purposes to which they are best suited. Utilization of special carbon bars and large shapes seems to be developing less slowly than special car- bon in the form of strip. There are many reasons for this and the future development of this trend will be important. Continued development of the manufacture of parts from strip and sheet to replace forgings, and of formed; structural members such as channels or welded pipe, is notable. Special carbon sheets with nonaging properties have been produced during the year; they maintain a higher degree of ductility over a longer time and are less sensitive to the changes which took place in the former product when stocked.

Jan 1, 1940

By J. E. Brantly

THE oil-producing industry may logically be 'divided into four independent branches: (1) Acquisition of possible productive lands by lease, fee purchase, concession, or otherwise and the perfection of titles thereto. (2) Studies of the geology of the properties, leading to the location of exploratory wells. These involve reconnaissance and detailed surveys and the use of geophysical instruments, where conditions do not permit surface determination. (3) Drilling of exploratory or test holes and, later, exploitation wells. (4) Actual recovery of the oil from the wells by flowing, pumping, or other methods. These four divisions of the industry are unrelated in detail of accomplishment, but they are entirely complementary, one to the other, and must, in any efficient' organization, harmonize in their respective efforts toward the desired ultimate end. The relative order for the first two branches is not necessarily the proper one; in fact one should have knowledge of the favorable possibilities of a given property before it is acquired, and preferably, also, final opinions as to then proper location for an exploratory well, if such is justified in the light of

Jan 1, 1937

By Eugene Mirsky, Eloy Ramos, May ElKhattab, John Wise, Terrence Carroll, Jose Torres

In 2017, Nicholson Construction Company completed a $72.1 million design-build contract for Miami Dade Water and Sewer Department to replace an existing 54-inch diameter pre-stressed concrete force main that runs from the Virginia Key Central District Wastewater Treatment Plant, under the Biscayne Bay at Norris Cut, to Fisher Island. In order to install the new sewer pipe below the bottom of Biscayne Bay, a tunnel boring machine (TBM) was launched from a 42ft diameter and 89ft deep shaft on Virginia Key and a precast segmentally lined tunnel was constructed towards a 28ft diameter and 72ft deep retrieval shaft on Fisher Island. Both shafts were constructed through sand and highly permeable limestone, primarily the Fort Thompson Formation which is part of one of the most permeable aquifers in the United States and two different techniques were used to ensure a water-tight shaft at each end of the tunnel drive. The launch shaft structure was built using the secant pile technique, wet excavation and a tremie plug. For the tunnel break-in a soil freeze block was installed after the ground was treated with low mobility grout. The retrieval shaft was built using the Deep Soil Mixing (DSM) technique and excavated in the dry. Precedence of any other structure built this deep through hard layers (UCS over 3,000 psi) using this technique was not found. This case study addresses the challenges of constructing watertight underground structures in highly porous ground for launching and retrieving a TBM. Design challenges from complex asymmetric loading, selection and comparison of the construction techniques, the installation and excavation of both shafts, and their performance are also discussed herein.

Jan 1, 2018

By Gernot Schenker

With the shut-down in the mid-1970s of the last shaft furnaces in the Harz Smelter Plant the long tradition of the Primary Lead Smelter in Oker came to an end. A continuation of the concern was nevertheless possible as a result of the timely commencement with the development and construction of lead production from secondary raw materials. Then as today, the most essential secondary raw material is lead accumulator scrap with over 80 % of the raw material pallet. Already in the 1960?s a method of reclamation lead battery scrap was developed and successfully carr.ied out by Preussag. In 1983 this process was fundamentally modified, also for environmental protection reasons within the framework of a rehabilitation programme of the existing plant. Today Metaleurop's HarzMetall GmbH in Oker is equipped with a modern secondary lead smelter which includes all environmental protection installations required by law. Besides processing battery scrap, the. smelter is in a position to process a ?multitude of other lead bearing residues in an economically useful way, whose waste disposal would otherwise be impossible due to the ever-increasing environmental protection laws or only be achieved at great expense.

Jan 1, 1990

By S. Hardcastle

Tele-remote operation of production equipment from surface will change the design criteria for underground mines. And for ventilation, with machine operators on surface, conventional planning to dilute and remove pollutants can become redundant. Natural Resources Canada with industrial partners are investigating what will be the new environmental design criteria. Additional complications include new mining equipment being designed without standard services and mines’ desire to eliminate conventional auxiliary ventilation. Findings to date show the cooling of equipment’s hydraulic systems to be the most demanding element, especially in dead-ends and when stationary. Consequently, revised ventilation based heat control strategies for equipment are being developed for the automated mine of the future.

Jan 1, 2001

By Chen Lin

Tectonic stress is an important parameter for understanding the dynamics of underground engineering and for the exploitation of coalbed methane. Multiple-period structural features usually have complex spatial relationships in tectonic superposition areas, which provides evidence for identification of the sequence of the tectonic stress period. Conjugated joints and slickensides are used to reconstruct the tectonic stress of the No. 8 Mine in Pingdingshan. Based on the geological unit division and field measurements, data on hundreds of joints and slickensides are collected from 33 stations. The tectonic stress results indicated by the conjugated joints show that there are mainly four directions of tectonic stress: NEE-SWW, NW-SE, NE-SW, and NNESSW. The tectonic stress results of the slickensides indicate that there are mainly four directions of tectonic stress: NNE-SSW, NNW-SSE, NEE-SWW, and NW-SE. According to the systematic analysis of the joints and slickensides, this paper separates the superposed joint and slickenside sets and identifies the tectonic stress periods with their abutting relationships. Three tectonic stress periods are determined and the sequence of the tectonic stress periods is NE-SW, NW-SE, and NEE-SWW. The results are consistent with other tectonic stress measurements for both the region and the locality.

By L. Wilfley, G. A. Calboreanu

"Wear resistant 25% Cr hard cast iron is a heterogeneous material containing 1,600 HV hard chromium carbides embedded into martensitic matrix. It is the most used cast alloy in wear operations of mining industry, chemical industry, fracking, etc. During the last decade the hard iron manufacturers increased wear resistance in the following ways: • Reduce / eliminate harmful retained austenite and chromium + carbon depleted areas especially within eutectic carbide cells. In Max5A the improved 25% Cr alloy brittle carbide eutectic cells are removed which increases toughness. • Delay delamination between chromium carbides and matrix particularly during sliding abrasion wear. Delamination commences at the weakest chromium carbide – matrix contact lines exposing chromium carbide to localized bending stresses which gradually chip carbides away. Once the chromium carbide base is removed accelerated wear degradation occurs. • Evenly randomize and avoid discontinuities in the chromium carbide network. When chromium carbides are perpendicularly positioned to the wear surface wear rate is minimized. On the contrary the highest wear rate takes place when 3D oriented chromium carbides are parallel with the wear surface. In this case chromium carbides cover top network discontinuities being just matrix supported which leads to rapid carbide cracking. The new hard iron discussed in this paper fulfils and exceeds the above requirements increasing the casting service life around 250% in various wear operations. Physical and mechanical properties of Max5A are compared with well manufactured Industry Standard 25% Cr hard iron. The paper presents practical accomplishments obtained in the USA, South America and India. INTRODUCTION The chemical composition of Max5A and Industry Standard 25% Cr are identical like specified by ASTM A532 Class III Type A requesting C = 2.0-3.3% and Cr = 23.0-30.0%. Manganese, silicon, nickel, molybdenum and copper contents are limited by maximum accepted quantities.[1] According to published data the eutectic chromium carbides chemical composition of 25% Cr hard iron is Cr = 54% and C = 8% which indicates strong depletion of chromium and carbon along chromium carbide - matrix interfaces. [2] The optimized Max5A microstructure has minimized retained austenite, is devoid of harmful carbide eutectic cells and has the most advantageous chromium carbide and secondary chromium carbide morphology. This favorable microstructure increases wear resistance, mechanical properties and corrosion resistance. The paper compares the Max5A microscopic features and mechanical – physical properties with similar properties of high quality Industry Standard 25% Cr."

Jan 1, 2017

By J. P. Powell

The importance of recovering more oil from known petroleum reserves has placed increasing emphasis on the application of secondary producing methods. One of the most successful of these has been the injection of water into depleted oil reservoirs. Water flooding is now recognized as a valuable conservation measure that not only prevents the premature abandonment of stripper leases but also is credited with reviving operations in many oil-producing areas previously abandoned. The injection of water into an oil-producing zone as a method of stimulating oil production was legalized in Kansas in 1935. Although water flooding had been attempted previously in other parts of the State, 1935 marked its introduction into the shallow stripper area of eastern Kansas. Two years later flooding was begun in the five-county area that is described in this report. Figure 1 is a map showing the water-flood areas in Allen, Bourbon, Crawford, Labette, and Neosho Counties, Kans. To July 1, 1955, the 77 projects in the oil fields of these 5 counties are credited with recovering an estimated 12.3 million barrels of oil that would not have been produced by methods used previously. These projects are expected ultimately to cover 10,700 acres, of which only 5,400 has been flooded to date.

Jan 1, 1957

By A. H. Winckers

"The San Nicolás deposit is a complex fine grained polymetallic volcanogenic massive sulphide deposit located in central Mexico.Metallurgical testwork was carried out in 1999 and 2000 to develop a flowsheet. During the course of the metallurgical testwork it became evident that it would be impossible to develop an accurate head gradehecovery based model for the projection of metallurgy. It was suspected that variability in mineral texture was a predominate factor affecting metallurgy. For this reason it was decided to evaluate the applicability of QEM*SEM technology to this test program.This paper summarizes the metallurgical testwork and describes the evaluation and subsequent application of the QEM*SEM technology to characterize the mineral texture throughout the deposit. Finally it is shown how the QEM*SEM data are used in the mine block model to project the metallurgy.The QEM*SEM (Quantitative Evaluation of Minerals by Scanning Electron Microscopy) is an automated image analysis system developed by CSRO which provides quantitative numerical estimates of the compositional and textural properties of the mineral suite which govern the concentration process.INTRODUCTIONThe San Nicolás deposit, was discovered in 1997 through the application of geological and geophysical techniques. The property lies 60 km southeast of the city of Zacatecas on the central Mexican plateau as shown in Figure 1."

Jan 1, 2002

By F. A. Campbell

This paper reports on mineral facies, ore textures, distribution of iron in sphalerites, and fractionation of sulfur isotopes in the Anvil ore body, Yukon Territory, Canada. Because the detailed structure and stratigraphy, both regional and local, are being studied by the geological staff at the mine and members of the Geological Survey of Canada, these topics will be discussed only briefly. The results of our study of the Anvil ore body have implications on theories of the genesis of ore deposits of this type, and these will be discussed. The Anvil ore body is the largest and most significant of three lead-zinc discoveries in an area of the central Yukon where major lead-zinc deposits were unknown only twenty years ago. The Vangorda deposit consisting of 22 million tons was discovered in 1953, followed in 1954 by the Swim Lakes deposit consisting of 10 million tons. The Anvil deposit, which consists of three ore zones, was discovered in 1964. The total reserve at Anvil mine is 63.5 million tons, with an average grade of 3.4% lead, 5.7% zinc, 0.16% copper and 1.2 ounces of silver per ton. This study is concerned primarily with the number one ore body which is about 2,400 feet long, up to 1,100 feet wide and 300 feet thick.

Jan 1, 1973

By Phillip E. Gramlich

Through extensive practical experience and multiple studies, tensioned roof control systems have proven beneficial in difficult mining conditions. Due to increased mining of less desirable seams, tensioned roof control systems have claimed a progressively larger share of the total number of roof bolts installed in the US coal industry. Each tensioned roof control system has its benefits, but also has problems concerning cost, cycle time, stress concentration, load retention, and protrusion into the mine opening. For example, resin-assisted mechanically anchored bolts (also known as resin point anchor bolts) have a fast cycle time and the potential for high tension loading, but the stress from the mechanical shell is concentrated in a small area and can create concerns with certain roof structures (Zhang and Peng, 2001). Resin point anchor bolts can be difficult to fully grout. The cost of resin point anchor bolts can be an issue; a two-piece resin point anchor bolt has a large number of parts (10) and manufacturing steps (9), adding to its higher cost. Tension rebar bolts can achieve high loads and are easier to fully grout but have longer cycle times. In addition, a high percentage of the installed load can ?bleed off? if the resin mixing time or the ?hold time? before tensioning is short-circuited. Tension rebar bolts can be notorious for protruding into the mine opening, creating an obstruction for man and machine (Figure 1), in particular, with reduced mining heights. A new tensioned roof control system has been developed that doesn?t have moving parts, is cost effective, provides fast cycle times, has a low profile, and is simple t install.

Jan 1, 2014

By S. Chatterjee, F. Suparno, A. Paithankar

Estimating reserves and quantifying resources stand as pivotal and intricate endeavours within the realm of coal mining operations. Intricate geological formations compound the challenges in resource estimation, thereby complicating reserve calculations. The uncertainties tied to geological attributes of coal, encompassing parameters like tonnage and coal quality, wield significant sway over resource and reserve computations within coal mines. This research delves into the domain of geological uncertainties, with a specific focus on calorific value, aiming to numerically characterise resources and reserves within an open-pit coal mine situated in Indonesia. To quantify resources, the coal seam geometry underwent simulation via a multipoint geostatistical technique known as single normal equation simulation. A geologically established coal seam served as the training image for generating 20 equiprobable coal models. To simulate CV, 50 realisations were generated for each simulated coal seam, utilising sequential Gaussian simulation. Deviations of the simulated coal seams ranged from -0.07% to 5.48% in comparison to the training image. The CV simulation yielded an average value of 5,920.29 kcal/kg, accompanied by a standard deviation of 586.54 kcal/kg. However, the average CV spanned from 5,305.26 kcal/kg to 6,526.55 kcal/kg across diverse simulations. For reserve calculation within the context of geological uncertainties, an algorithm rooted in maximum flow graph theory was employed to construct the ultimate pit for the coal mine. Within this final pit, the average stripping ratio was 1.62, coupled with a CV value of 6,019.66 kcal/kg. When juxtaposed with the deterministic model, the findings underscore that the stochastic ultimate pit delineates a more expansive excavation, accompanied by a heightened undiscounted cash flow.

Oct 2, 2025

By W. A. Thomas

STEAM is, and doubtless always will be, the basic power in the anthracite industry, either directly applied through engines and pumps or electrically. The rapidity with which electric power is being applied to the mining and preparation of anthracite leaves little doubt as to its utility and economy. There is practically no operation, except possibly the drilling of hard rock, that has not been successfully electrified and the matter of drilling is handled economically with electrically driven compressors and the standard compressed-air drills. Conservation and the seemingly ever-increasing cost of production, justify careful consideration of the possible results of the more extensive use of electric power in the industry. It is not planned to discuss, herein, the relative economies of individual applications but to consider the relative economy and flexibility of steam and electric power. The reports available for the year 1920 indicate a production of slightly over 80,000,000 tons of anthracite, of which 8,843,500 tons were used for power and heating purposes; in other words, over 11 per cent. of the production was used at the mines. Some of this was used to generate electric power at the mines, about 160,000,000 kw-hr., while 150,000,000 kw.-hr. was purchased from the public utility companies. One large producer, who is buying some electric power and generating some, used over 13 per cent. of the production for power and heating at the mines. Another producer, where considerable electric power is generated on the properties, is using less than 9 per cent. of the output for power and heating. One of the largest producers has a fuel consumption of over 15 per cent. of the output, besides which considerable power is purchased. A careful study of the field indicates that steam-operated plants use upwards of 13 per cent. of the production for power and heating, while electrically operated plants use about 1 per cent. for heating; so that, for steam-power purposes at least 12 per cent., or 268.8 lb., are used for power out of each ton produced.

Jan 9, 1921

By J. O. Voigt

No major changes took place in the salt industry during 2004. No new uses of salt appeared and only localized supply disruptions occurred. Many salt producers reported slightly increased salt sales and profits for the year. In the United States, about half of the salt supply is produced as brine, by solution mining, and is used by the chemicals industry. One-third of U.S. salt is produced as rock salt by 14 underground mines. The remaining two production techniques, each with less than 10 percent of the total tonnage, are vacuum-pan-evaporation for refined, food-grade salt, and solar pond crystallized salt.

Jan 1, 2005

By R. A. Hatch

This report summarizes the results of nearly 8 years research on and production of synthetic mica at the Electrotechnical Experiment Station of the Federal Bureau of Mines, Norris, Tenn. This program was undertaken at the request of the United States Department of the Navy and was financed mostly by the Army Signal Corps and the Navy Bureau of Ships through a contract with the Office of Naval Research, The original objectives included fundamental studies of fluor-phlogupite and other fluorine-micas and production of synthetic mica sheets on a pilot-plant scale. The first 3 years of this project were devoted mainly to a search for practical solutions of the many problems involved in designing and constructing a pilot plant for crystallizing fluor-phlogopite mica. The first and most urgent need was a suitable container for the corrosive mica melt. After extensive study, it was concluded that platinum, graphite, high-silica fire clay, and silicon carbide were the most promising refractories for crucibles; but none was perfect. Silicon car¬bide seemed to have the better combination of qualities, combining good corrosion resistance with oxidation resistance.

Jan 1, 1957