Search Documents

By Lucas Nana Wiredu Damoah, Lifeng Zhang

"Increasing demand for Solar Grade Silicon (SoG-Si) due to rising interest in renewable energy has lead to increased SoG-Si Top – cut scraps generated from the multi-crystalline silicon making process. Due to the high cost of SoG-Si and the potential to use the top-cut scraps as feedstock material, there has been increased effort to develop cost effective and efficient technologies. As a result, several methods to recycle the top-cut scraps are currently been applied, and researched. These include settling under gravitation field, which is a slow process to be industrially applicable. Natural settling of inclusions by gravitational force is a slow process and not attractive to the industry. Recent experiments on Top-cut SoG-Si scrap under high frequency, high voltage, electromagnetic field showed that SiC inclusions settled within a short time to the bottom of the crucible and the characteristic rod-like morphologies of Si3N4 inclusions in SoG-Si were not detected. This study investigates the enhanced settling of SiC inclusions and the behavior of Si3N4 particles under the influence of high frequency, high voltage, electromagnetic field in Top-cut SoG-Si.IntroductionThe photovoltaic industry depends on silicon based PV materials either as single-crystalline silicon, or multi-crystalline Si (MC-Si), or amorphous Si [1] for over 90 % of its market share. [2] MC-Si produced by directional solidification of solar grade silicon melt dominates the silicon PV market. During the directional solidification process, SiC and Si3N4 particles within the melt are pushed by the solidification front to the top of the ingot which is the last to solidify. Therefore the top of the ingot is cut generating what is known as top-cut solar silicon scraps. The Si3N4 particles are mainly from the coating material at the inside surface of the silica crucible and from air absorption during the solidification process. The SiC particles mainly stem from the carbon reduction process of the primary production of silicon [3]. Due to the growth of the PV industry as a result of global demand for clean, reliable, and affordable energy [4], there is the need to develop new methods to compliment exiting ones to recycle SoG-Si waste (e.g. top-cut) for sustainability."

Jan 1, 2012

By M. Sandin

According to the world bank1, the mining industry consumes up to 11 percent of global energy use. In comparison, 70 percent of mining projects from the six largest mining companies operate in water-stressed regions. To steer the direction of the process industries toward more sustainable practices, more than 40 governments have adopted a price on carbon. This measure includes additional taxes on the use of fossil fuels, trade programs, new standards for renewable energy, energy efficiency mandates, more stringent emissions regulation, carbon offsets, etc. This emphasis is also supported by investors shifting their priorities to reduce risk by focusing on long-term plans, including environmentally friendly operations. The metals and mining industry is at the core of the green energy mix and electrification of vehicles. This new trend creates an astronomical increase in demand for minerals. Under a 2-degree scenario, according to the latest analysis from the world bank, as new energy technologies continue to grow, it is expected that all minerals to double in demand, and the distribution of these materials will depend on their application. • Solar panels, will account for 87% of the aluminum demand, and more than 95% of silver • Wind turbines and geothermal plants will require 98% zinc and 64% titanium. • Solar and wind energy alone will demand more than 74% of the global supply of copper, and this is without considering wiring or other infrastructure to connect the grid • Battery storage accounts for 100% of the graphite and lithium demand. (Hund, 2020) • Other materials, such as nickel and steel, are also projected to more than double in demand as they are cross-technology minerals. These materials require a manufacturing process that is accountable for the emissions proper of the transformation process. It requires that these processes move from a hindsight mode focused on reporting to a forecasting mode based on run-time measurement of GHG emissions. This is a critical first step in companies realizing an economic return for doing the right thing for the environment and their communities.

Feb 1, 2023

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to simulate nickel flash smelting process. In the nickel flash furnace, oxidation of concentrate occurs at one end, and reduction of slag occurs at the other. The model makes use two zones, namely the reaction shaft/settler zone and the appendage zone and accounts for 6 phases (matte, slag, silica, magnetite, Cu-Ni alloy and gaseous phase), 13 elements (Ni, Co, Cu, Fe, S, 0, N, C, H, Si, Al, Mg and Ca) and 33 chemical components in nickel flash smelting system. The compositions of matte, slag and gaseous phases in equilibrium are calculated by using the data of free energies of formation and activity coefficients of components. Two nickel sulfide species are used to allow for the modeling of sulfur-deficient mattes. The model predictions are compared with the known industrail data from Kalgoorlie Nickel Smelter, and excellent agreement is obtained. The model can be a very useful tool for monitoring and optimizing the actual industrial operations of nickel smelting process. The distribution behaviors of Ni, Co, Cu, Fe, S and 0 in the nickel smelting furnace depend on the process parameters such as smelting temperature, volumes of air, the content of the elements~ charge and oil.1. IntroductionThe nickel flash smelting furnace essentially consists of a reaction shaft where nickel sulfide concentrate is partially oxidized with air, a settle zone where matte and slag are allowed to separate, and a slag cleaning end where coke is added to provide for the reduction of the oxidized nickel from slag, and electrodes are used to provide heat.The theoretical model to consider a mass balance for copper flash furnace is developed by S. Goto and R. Shimpo[1][2J. However, this can not be true for nickel flash furnace as a whole since oxidation of concentrate occurs at one end (in the reaction shaft/settler), and reduction of slag occurs at the other (in the appendage). Despite these limitations, an acceptable pseudo-thermodynamic description of the furnace can be achieved using essentially two zones, namely the reaction shaft/settler zone and the appendage zone. Compositions of gas, slag and matte in two zones are calculated."

Jan 1, 1998

By W. G. Davenport

A flash furnace can be run many different ways. It can, for example, be operated with: (a) highly 02"enriched, ambient temperature blast and no fossil fuel (b) considerable fossil fuel and hot, slightly Or enriched blast. It can also produce different grades of matte. With all these possibilities, the flash furnace operator can benefit from any technique that will indicate the 'best' way to operate his furnace. One such technique is Excel's 'Solver'optimizationroutine#. This chapter shows how our matrices and Excers optimization.abllity can be used to optimize a flash furnace operation. The chapter sets three optimization goals: (a) minimum industrial oxygen + oil cost, $ per tonne of concentrate (b) maximum smelting rate, tonnes of concentrate per hour (c) maximum profit, $ per hour.

Jan 1, 2001

By S. Wegerer, M. Semel

The search for minerals typically starts with a reconnaissance phase. After finding a promising target area, further prospecting work will be conducted. Finally with growing confidence of having encountered an ore deposit with commercially viable concentrations of relevant minerals, an extensive exploration campaign will verify its potential. Best practice and reliable, efficient tools for mineral resource estimation of massive sulfide deposits in the deep sea have to be established yet. Therefore, a new seabed exploration system is in development. Various challenges are caused by the extreme environmental conditions in the deep sea and by the nature of massive sulfide deposits. Information of past and ongoing expeditions were gathered to form the basis of an in-depth requirement analysis. System functions and corresponding process times were derived. The experience from the existing MeBo seabed drill rigs serve as starting point for the concept study and following development. Initial MeBo system was built for maritime research purposes and now has to be converted into a new design, suitable for efficient and economic resource exploration. The new system configuration is modular structured to adapt easily to different application scenarios and challenges. To achieve an extension of the deployment depths, the overall equipment weight has to be limited through light weight construction and material. The drilling module contains a range of geotechnical coring tools to face the varying soil conditions of heterogeneous massive sulfide formations. The major challenge to overcome is the touch down sequence on uneven, 25° inclined, rough terrain in up to 4.000 m water depth. Furthermore, high precision of the final unit positioning is necessary. Landing sub-system proof of concept is validated in laboratory environment with small scale model. A novel seabed exploration system capable to land and operate safely on highly inclined slopes of mineral deposit is described. Obtaining high quality samples by wire-line coring technique is the objective.

Feb 22, 2026

By Arthur H. Redfield

The expansion of city street laving which characterized the ten years ended December 31, 1929, according to a survey of 201 representative cities, made by the bureau of Mines, reached it climax in 1927, with decreases reported for 1928 and 1929. The upward trend, followed by a decline, was general in cities of all sizes included in this study, but was most pronounced in cities of 40,000 to 100,600 inhabitant and in the Northeastern, Southeastern, and Southwestern States. In the North-Central States the trend of paving; was downward from 1925 to 1929; in the Pacific, and Rocky Mountain States it was generally upward. Over the nation as a whole, bituminous types of paving continued to lead, furnishing two-thirds of the total street pavement laid in the 201 cities from 1925 to 1929. The actual yardage of bituminous pavement laid in these cities, however, was 3.8 per cent less in 1923-than in 1925, and the ratio of bituminous pavement to the total pavement t dropped from 70.4 per cent in 1925 to 62.1 per cent in 1928, rising to 65.1 per cent in 1929. The area paved with Portland-cement concrete amounted to only one-fourth of the total, pavement laid in these cities from 1925. to 1923., but the yardage of Portland-cement pavement increased by half during the period, and its share in the total pavement grew from 19.3 per cent in 1925 to 30.0 per cent in 1928, declining to 29.5 per cent in 1929. Brick, block, and stone pavements, which constituted the remaining one-twelfth of the total pavement laid in the 201 cities, decreased one-third in yardage, and declined in relative importance from 10.3 per cent in 1925 to 6.6 per cent in 1929.

Jan 1, 1931

By Enrique Rubio Esquivel, Matías Fuentes Bustamante

The transition from open pit to underground mining represents a key strategic challenge in modern mine planning. This paper presents a multicriteria and multivariable methodology to plan such a transition, integrating technical, economic, environmental, and social considerations. The proposed framework focuses on risk reduction (de-risking) through the identification of alternative development paths, the use of stochastic simulation to model geological and technical uncertainty, and different mining strategies such as methods, production rates, sequence, etc. for ultimate underground implementation. The study summarizes the limitations of traditional planning methods—which usually treat the open pit and underground mine designs as independent processes—, also often it considers a single mining method and production rate for the underground option. Instead it is proposed an integrated approach that leverages synergies between both mining methods and scalable production rates. Also the proposed methodology incorporates the definition of critical variables (geotechnical, economic, and social, among others), the construction of multiple operational and technological transition paths, and the evaluation of each path under criteria of economic attractiveness and practical do-ability (capacity to be executed). Using simulation tools (SIMPLAN for operational performance and SIMVAL for economic evaluation), probabilistic distributions of the different path are obtained, enabling the quantification of the project’s Value at Risk (VaR). A subsequent multicriteria analysis weights the expected profitability against the feasibility of execution of each alternative, producing a decision matrix that provides a framework for evaluating the different project path. As a result, the proposed approach identifies OP→UG transition strategies that maximize business value by capturing remaining resources while minimizing financial and operational risks. Finally, strategic conclusions and recommendations for the industry are provided, emphasizing the importance of early transition planning even challenging the open pit sequencing of the latest push backs by introducing early underground operations. Future work includes strengthening the methodology—such as integrating real-time analysis and adaptive decision-making—and providing recommendations for its application in various mining operations. In summary, this paper delivers a technical and professional framework to guide mining companies on when and how to carry out a successful transition from open pit to underground mining, balancing resource recovery with financial, operational, and social security.

Feb 22, 2026

By Michael Gauna, Christopher Mark

"For decades, pillar recovery accounted for a quarter of all roof fall fatalities in underground coal mines. Studies showed that a miner on a pillar recovery section was at least three times more likely to be killed by a roof fall than other coal miners. Since 2007, however, there has been just one fatal roof fall on a pillar line. This paper describes the process that resulted in this historic achievement. It covers both the key research findings and the ways in which those insights, beginning in the early 2000s, were implemented in mining practice.One key finding was that safe pillar recovery requires both global and local stability. Global stability is addressed primarily through proper pillar design, and became a major focus after the 2007 Crandall Canyon mine disaster. But the most significant improvements resulted from detailed studies that showed that local stability, defined as roof control in the immediate work area, could be achieved with three interventions:• Leaving an engineered final stump, rather than extracting the entire pillar;• Enhancing roof bolt support, particularly in intersections, and• Increasing the use of Mobile Roof Supports (MRS)A final component was an emphasis on better management of pillar recovery operations. This included a focus on worker positioning, as well as on the pillar and lift sequences, MRS operations, and hazard identification. As retreat mines have incorporated these elements into their Roof Control Plans, it has become clear that pillar recovery is not ""inherently unsafe.""The paper concludes with a discussion of the challenges that remain, including the problems of rib falls and coal bursts.INTRODUCTIONPillar recovery has always been an integral part of underground coal mining in the US. When room-and-pillar methods are employed, large blocks of coal in the form of pillars are initially left in place to support the weight of the overburden. Unless these pillars are subsequently recovered, the coal they contain will never be mined."

Jan 1, 2016

By N. J. Rarmrez, C. Perez, J. D. Calderon, L. Lopez

"Among the thermal characterization of any material, one of the variables to know is the coefficient of thermal conductivity because this value can tell how much heat passes through the material and if the material could be used as an isolator. In order to determine this parameter is required some kind of special equipment and controlled conditions which implies high costs in the development of tests. The present paper proposes a design of a low cost measurement system in order to determine this coefficient with the lower possible error. This equipment was thought for companies or labs where they do not have the economic resources or the infrastructure (environmental controlled labs, heat flux transducers, human resources with specialized knowledge) to do this kind of tests.The system is based on ASTM C 518 - 04 [l] and integrated by two plates (one that contains a thermal resistance and which temperature is controlled by a closed loop controller and the other one with a route of water flow). The thermal resistance is actuated by a relay and a supervisor system checks the total time the relay is on in order to determine the effective power applied to the system. The contact faces of the plates contain a group of temperature sensors connected to a data acquisition system that process and record the temperature in each measurement point.With the power applied to the system, the measurement of temperatures and a process of calibration is possible to determine the coefficient of thermal conductivity. IntroductionWithin the thermal characterization of a material of known variables is the coefficient of heat transfer, since this value can know the amount of heat the material is capable of transferring or isolating. To determine this ratio requires specialized equipment and controlled conditions, which implies high costs in the development of a test. This article proposes a design of a low cost machine to allow closer this coefficient with the least possible error. This equipment was done thinking about companies that do not have the infrastructure (laboratories, controlled environment, heat flux sensors, human resources expertise) and financial resources to conduct these tests."

Jan 1, 2011

By V. F. STANLEY

THERE is not the slightest doubt that the present recoveries of valuable minerals by the Broken Hill mills could be improved, and that further machinery would be installed for the purpose if it could be assured that a high price of metals would be maintained; but concentration, like all other com¬mercial propositions, is a question of profit and loss, and no sensible metallurgist would carry out his work in such a manner as to obtain high recoveries at a financial loss to his company. There is a point in all concentration at which the added money obtained from the higher recovery of minerals is balanced by the extra cost of obtaining the last part of the recovery; a wise metallurgist will be content with his work before his working-expenditure reaches this point. To a casual observer, the work being done by the various Broken Hill mills is identically the same. A closer investigation will show that this is far from being the case, for it is a remarkable fact that, although the larger mines extend over a length of approximately only 2 miles, such a difference in the physical and chemical properties of the ores exists that, from the first reduction downwards, special treatment is necessary in each case, and hardly any two mills are identical in operation. The details of this paper refer directly- to the work of one . particular mill in Broken Hill, for the reason that the ore from each mine presents special difficulties and requires its own special treatment. I have selected the mill referred to because it has been constructed and modified under my supervision.

Sep 1, 1909

By N. O. Lotter

The connection between mineralogy and metallurgical performance in a plant was recognised long ago (Gaudin, 1939; Petruk, 1976; Petruk and Hughson, 1977; Cabri, 1981; Petruk and Schnaar, 1981; Kinloch, 1982; Peyerl, 1983, Baum et al 1989 for example). The modern toolbox that we now routinely use for flowsheet development took decades to develop (Lotter et al., 2002; Baum and Lotter, 2004; Lotter, 2011 for example). Many workers contributed considerable time and effort to this overall mission of connecting sampling, mineralogy and mineral processing to integrate the flowsheet development activities. Certain key milestones marked this journey, such as Gy’s treatise on the sampling of particulate materials in 1979, which was later added to by François-Bongarçon, Pitard, Minnitt, and Holmes for example. The development of QEM*SEM by Gottlieb et al. of the MLA by Gu et al. constituted a huge leap forward in accuracy and mineral measurement capacity, as well as a reduction in standard errors of mineral characterisation. The advancement of the microprobe to an automated platform made a significant difference to detailed compositional mineralogy. This led to a strong position from which to draw meaningful processing implications from the mineralogical data. Reproducible flotation testing and reliable plant survey material for characterisation was dealt with by, amongst others, High Confidence Flotation Testing ( Lotter, 1995: Runge, 2010, and Bradshaw, 1997); and Statistical Benchmark Surveying (Lotter, 2005), with earlier prototypes which were steadily improved (Lotter, 1994; Restarick, 1976). The sterling work of Napier-Munn in engaging sound statistical methods with mineral processing led to the successful design and use of methods that could identify and quantify small recovery gains in plant scale trials. This history and present capability are reviewed, including leverage into asset management.

Jan 1, 2018

By Lukas Walder, Roland Arnold, Raphael Zuber, Richard Gradnik

This paper presents the construction of the ventilation shaft for the single-tube, doublelane Kramer tunnel. The project is located in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of Garmisch-Partenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million incl. VAT (US-Dollar 201 million), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for singletube tunnels is solved by a parallel escape tunnel passable for vehicles. For tunnel ventilation, an intermediate shaft has been designed with a depth of approximately 90 m (295 feet) and an inner diameter of 4.5 m (14.8 feet). All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). The geological and hydrogeological conditions, the change in the profile (from round to square geometry), and also the shaft being located at a high elevation presented a demanding technical and logistical challenge. The site arrangement with the pit bank was located in a cut, the slopes of which had to be stabilized with shotcrete and soil nails. This excavation was carried out from the fall of 2020 to the beginning of 2021 because construction operations had to be completed outside the nesting period of protected birds.

Jun 13, 2023

By Victoria Vaccarezza, Corby Anderson

The demand for rare earth elements for everyday technology and applications has initiated much research into the extraction and recovery of these rare earth elements. An otherwise unknown group of minerals, eudialyte is a zircon silicate consisting of rare earth oxides (REO), contained in a unique mineral structure and represented by a complex chemical formula. Research into extraction and recovery of rare earth elements involves various beneficiation and hydrometallurgical techniques. The goal of beneficiation being to efficiently liberate and upgrade the REO content, followed by hydrometallurgy to extract the desired elements. This overview will discuss previous research on treating eudialyte group minerals via different mineral processing and extraction techniques.

By D. M. Aloi

In today's evolving and globalized world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to "engage" with communities and measure the success of these engagements without a clear understanding of "how" to do this. This move, away from "Corporate" Social Responsibility (CSR) and compliance, develops more of a focus on "Community" Social Responsibility and sustainability. This shift in focus leads to the development of world-class projects that provide sustainable development for people, reduces the incidence of costly delays, and promotes good global citizenship for corporations. The process of "engaging" communities in mining project design and development leads to a stronger license to operate and sustainable development. To create this mutually beneficial relationship between communities and companies, communities must be "engaged" in the mining process as early as possible, preferably during the exploration or the concept phases. How to create this "engagement" remains elusive. How to measure the progress of this engagement is also problematic. The quantitative and qualitative metrics needed to measure both positive and negative impacts of the mining and community relationship will be discussed.

Jan 1, 2007

By Jewel A. Gomes

Keywords: Electrocoagulation, arsenic removal, fuel cell, windmill, energy simulation, combined Fe-Al electrode assembly Arsenic contamination of well-water in different countries has caused signs and symptoms of arsenic poisoning. Although several physicochemical treatments are presently used for the removal of arsenic compounds from drinking water, an electrochemical treatment, electrocoagulation, is a promising processing technology and currently is the most efficient (above 99% removal) and environmentally friendly technique, particularly if combined with alternative energy sources. Wind and fuel cell technologies can be considered the most promising developmental clean power sources. We will discuss new insights into the materials processing mechanisms and show the coupling of electrocoagulation with fuel cells and simulated wind energy sources. Different electrocoagulation plate materials were considered, along varied currents from the fuel cell to produce maximum arsenic removal. Coupling these technologies will remove carcinogenic arsenic from water sources, and will exhibit efficient usage of these energy sources by producing pure water for human and agricultural consumption.

Jan 1, 2005

By G. Kyle Green

Zirconium chlorinator residues contain an array of rare earths, scandium, unreacted coke, and radioactive thorium and radium. Because of the radioactivity, the residues must be disposed in special waste containment facilities. As these sites become more congested, and with stricter environmental regulations, disposal of large volumes of wastes may become more difficult. To reduce the mass of disposed material, the U.S. Bureau of Mines (USBM) developed technology to recover rare earths, thorium and radium, and unreacted coke from these residues. This technology employs an HCl leach to solubilize over 99% of the scandium and thorium, and over 90% of the rare earths. The leach liquor is processed through several solvent extraction stages to selectively recover scandium, thorium, and rare earths. The leach residue is further leached with an organic acid to solubilize radium, thus allowing unreacted coke to be recycled to the chlorinator. The thorium and radium waste products, which comprise only 2.1% of the original residue mass, can then be sent to the radioactive waste facility.

Jan 1, 1995

By A. Rios

ENAMl's Paipote Smelter commenced operations in 1951. At present, it processes 230,000 tonnes/year of green feed in a conventional smelter, which comprises one reverberatory furnace, two Hoboken, one Peirce-Smith converters and one rotary anode furnace. The feed is composed of 83% copper concentrate and 17% metallic copper precipitates, which results in a feed average grade of 32% of copper content. The final products are 75,000 tonnes/year of copper anodes and 48,000 tonnes/year of sulphuric acid. At present, the plant is undergoing a modernization to expand the smelter capacity to 300,000 tonnes/year of green feed and increase the sulphuric acid production to 100,000 tonnes/year. This will be achieved with the installation of an El Teniente Converter and an expansion in the acid plant. The work began in November 1991 and is scheduled to be in operaton by March 1993. The paper provides an overview of the modernization plans and results achieved to-date.

Jan 1, 1993

By J. Drelich

The adsorption of oleate at the surface of titanium dioxide from aqueous solutions was examined by Fourier transform infrared (FT -IR.) spectroscopy using a germanium internal reflection element coated with a thin film of TiO2. This thin film, with a thickness of 100-200 A, was deposited on the surface of a germanium single crystal by RFIDC magnetron reactive sputtering. It was found that significant adsorption of oleate from a 0.02-0.03 mM aqueous solution on the surface of TiO2 thin film occurs at neutral pH, from about pH=5.5 to pH=7.7. Adsorption of oleate at the surface of the amorphous TiO2 thin film appeared to be reversible, involving soap-acid dimers.

Jan 1, 1997

By S. Shrestha

Magnesium-based alloys are of growing interest for many industrial applications due to their favourable strength-to-weight ratio and excellent castability. Mass reduction has advantages in many industrial sectors for example, in automotive, a reduction in mass improves fuel economy and can lead to more efficient mechanical systems by reducing the weight of moving parts like wheels, gears, pistons. However, the relatively poor corrosion and wear resistance limits the use of magnesium and its alloys in many potential applications. The patented Keronite® plasma electrolytic oxidation (PEO) process enables manufacturers to overcome such problems and, in its latest generation equipment has been developed to industrial realisation for high volume production. This paper presents microstructural characteristics and corrosion performance of two most widely used high pressure die-cast magnesium alloys AZ91D and AM6OB with a duplex corrosion protection coating system that comprised a thin Keronite pre-treatment followed by a subsequent automotive grade final powder coat.

Jan 1, 2006

By B. J. Moore

This publication contains routine analyses and related source data for 547 natural gas samples from 22 States and three foreign countries. Of this total, 340 samples were collected during calendar year 1967. The remaining 207 analyses are of samples collected during previous years, but releases granting, permission to publish the results were not received until 1967. All samples were collected as a part of a continuous survey of the free world for occurrences of helium in natural gas. The Bureau of Mines has conducted this survey in the United States since 1917, and in 1965 it was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 516.4 Nine previous publications have been made to present results of 7,618 gas analyses made by the Bureau of Mines Helium Activity prior to 1967. The first three, Bulletins 486,5 576,6 and 6177 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other six

Jan 1, 1968