Search Documents

By G J. Harbort, K Lam, C Sola

The relationship between the geology of porphyry copper deposits and their processing performance is an area of interest. Being able to predict comminution properties of the ore from physical characteristics and geological descriptions would allow an increase in the precision of capital cost estimates, operating cost estimates and throughput rates. This geometallurgical approach would reduce the requirements for expensive comminution tests.As the comminution circuit is the highest capital cost item in the plant and a possible throughput bottleneck, understanding the variability in hardness within the orebody is critical. A geometallurgical model allows calculation of ore hardness values in mining blocks from ore characterisation data. This model subsequently uses a combination of simulation and power-based approaches to relate ore hardness and flotation feed size to grinding circuit throughput.This paper reviews the geometallurgical models developed for seven porphyry copper deposits and discusses the strengths and shortfalls of the methodology and similarities and differences between the different deposits.CITATION:Harbort, G J, Lam, K and Sola, C, 2013. The use of geometallurgy to estimate comminution parameters within porphyry copper deposits, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 217-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By W. Song, C. Richards, B. Q. Li

"This paper presents a two-phase flow numerical model for spouting gas-particle flow reactors used in chemical vapor deposition processes for manufacturing heart valves and other biomedical implants. The model is developed based on the Eulerian-Eulerian formulation of gas-particle flows, with the k-e engineering model modified with the presence of particles for the description of turbulent gas flows. In parallel with the numerical model development, physical models are set up, where the particle image velocimetry is used for visualizing the particle flows and spout shapes and heights and optical probes are used to measure the particle velocities. The numerical model predictions are compared reasonably well with the experimental measurements.IntroductionVarious biomedical implant components, such as bone joints, dental components and heart valves, are coated with bio-compatible thin films by chemical vapor deposition in particle-laden chemical reactors [l-5]. In these reactors fine particles are used as packing and supporting media. During the coating operation, these packed particles are fluidized by an upward gas jet from the nozzle, reach a certain height and fall back on the top of an annulus region. These recirculating particles are mainly for levitating the implant components (usually one or two in a reactor at one time) so that every portion of them is equally exposed to the gaseous atmosphere. An equal exposure is critical for forming a uniform, mechanically strong and corrosion-resistant coating on implants. Plant experience shows that the quality of the coating is directly related to a stream of operating parameters such as temperature, particle size and loading, and gas flow rates [6]. Optimization of these operating parameters for improved reactor performance depends crucially upon our fundamental understanding of the physics governing the gas-particle flow, heat, and mass transfer phenomena taking place in these reactors."

Jan 1, 2004

By D Caffrey

To demonstrate the advantages of using electronic delay detonators over pyrotechnic detonators, a trial using the DNES Dynatronic System was conducted at the KCGM Mount Charlotte operation in 1998. The trial clearly demonstrated that accurate control over the firing delay time between blastholes can lead to fragmentation improvement and ground vibration energy control which are two important issues for the Mt Charlotte underground operation. Excellent fragmentation was achieved by employing a 12 ms delay sequence. Detailed fragmentation analysis has shown a 10 to 20 per cent passing increase for the rock fragment size from 0.1 to 0.4 m compared with the pyrotechnic detonator firing. There was no increase in ground vibration level on the surface with the electronic detonator firing even though the electronic detonator firing had a much shorter blast duration than the pyrotechnic detonator firing. In fact, our energy calculation has clearly shown that much less energy had been propagated to the surface from the blast using electronic detonator firing.

Jan 1, 1999

By D. V. J. W. Groenewald, T. M. Louw, L. Auret, S. M. Bradshaw, A. V. Cherkaev

Unexpected equipment failures lead to financial losses due to production disruption. Time-based maintenance, based on checks over regular time periods, has been employed to minimise disruption. However, the improvements it can offer are limited as it may lead to unnecessary service of healthy equipment or missed failures occurring between service intervals. Condition-based maintenance (CBM) provides a further improvement to equipment reliability by detecting faults and predicting remaining useful life (RUL) based on equipment health monitoring. Its application in the mineral processing industry is hindered due to the high cost of health monitoring equipment. In this study, two stochastic process models, the adaptive auto-regressive model and the gamma process, are compared in their ability to forecast the degradation state and to provide RUL prediction. The gamma process model was found to be effective in both tasks. Due to its simplicity and minimum hyperparameters requirements, it is proposed to use the gamma process as a baseline for comparison with other models. Keywords: Condition-based maintenance, remaining useful life, slurry pump, adaptive autoregressive mode, gamma process

Jan 1, 2020

By M. P. Valoski

In the United States, the occurrence of underground mine fires/explosions continue to decrease; however, they pose great danger to the miners and any subsequent mine rescue teams and/or fire brigades. Tragically, 19 coal miners lost their lives in 2006 at fires or explosions. Fires/explosions can devastate a mine and cause its permanent closure. It is vitally important to obtain accurate information on the gas content (concentration and composition) of the mine atmosphere after the event so that appropriate action can be instituted to rescue any trapped miners while not exposing the mine rescue teams to unnecessary hazards. Additionally, the fire fighting techniques (spraying water, sealing, etc.) will be dictated by the gas content. Finally, the gas content will determine when it is safe to recover the mine. The gas content of the air can be determined using detector tubes, handheld instruments, portable instruments, or gas chromatographs. No single instrument is suitable for all analyses. Each type of instrument has its advantages and disadvantages. This paper discusses these attributes.

Jan 1, 2010

By Jingzhi Liu, Xueping Hu, Huai Wang, Simin Yang, Baoqiang Yu, Deguang Zhan

In this study, response surface methodology (RSM) and Box-Behnken design to improve copper extraction from refractory copper oxide ore were investigated. Based on single factor tests, quadratic polynomial equation to describe the relationship between influencing factors (particle size, leaching temperature, sulfuric acid concentration, leaching time) and copper leaching rate could be obtained by RSM. The optimum parameters determined by the model are as follows: particle size 64.60% − 74 μm, leaching temperature 74.15 °C, sulfuric acid concentration 0.49 mol/L, and leaching time 140.85 min. Under these conditions, experimental copper leaching rate of 85.12% could be achieved, which was very close to the predicted maximum value (85.34%) by the model, indicating the quadratic polynomial model was accurate and reliable. Copper leaching rate increased approximately by five percentage points comparing to the result of single factor tests. This study indicates that response surface methodology is an effective method to optimize experiment conditions and achieve an ideal experiment result.

Aug 17, 2022

By Guangchun Yao, Chuan Li, Hongjie Luo, Zhuokun Cao

"The expansion rate and collapse time of liquid aluminum foams are essential for the determination of operating time and quality of the resulting foam. In the present paper, liquid aluminum foams was fabricated by adding in TiH2 as blowing agent, and the variation of expansion rate with foaming time was non-contact detected by a laser distance measurer. The influence of different stabilizing agent and alloying elements was studied. The results show the fact that the fraction of stabilizing agent only perform little effects on the maximum expansion rate of liquid aluminum foams, while the influence of alloy elements are remarkable. The maximum expansion rate would increase much when Mg is added, and the liquid foam also collapse at a shorter time. Comparison was made between experimental results and mathematic calculations, which reveal the fact that it is the change of TiH2 decomposition responsible for the change.IntroductionMetal foams, combining light weight with other unique mechanical and physical properties, have gained wide interest and been developing fast during past few decades. However, manufacture of this new material is quite challenging since it involves simultaneous occurrence of gas, liquid and solid phase at high temperature [1-2].Quite some manufacture routes have been developed for manufacturing metal foams, and the structure and quality of resulting foam are remarkably improved during the last decades. However, most of the past works seems to be experiential, and because the lack of basic knowledge of foaming process, the start material is limited and the production technologies are far from reliable and reproducible.[3-4]In direct foaming process, decomposition of blowing agents, TiH2 for example, is the main force for foam expansion. The density and foam structure changes with time during the foaming process, so it is expected that foams of certain structure can be obtained by solidification of the liquid foam at a certain time [5-6]. However, the foaming process is weak in reproducibility and the influence of stabilization additives and alloying elements is unclear."

Jan 1, 2011

By Tracy Brettmann, Melis Sutman, C. Guney Olgen

"The use of energy piles for geothermal heat exchange has been steadily increasing during the last decade, yet there are still pending questions on their behavior during temperature changes. This paper focuses on the thermo-mechanical response of three full-scale energy piles installed in Richmond, TX. The behavior of test piles subjected to thermo-mechanical loadings was studied in situ with the aim of quantifying the thermal influence on the performance and capacity of energy piles. An extensive field test program, including conventional pile loading tests and application of heating-cooling cycles was conducted on the test piles during a period of six weeks. For thermal load applications, the heat exchanger fluid with maximum temperature of 113°F (45°C) and minimum of 47°F (8°C) was circulated in the geothermal loops placed at the center of the test piles. Optical fiber sensors, vibrating wire strain gages, thermistors and thermal integrity profile wires were installed to monitor the strain and temperature variations along the energy piles throughout the field tests. The strain and temperature profiles during heating-cooling cycles on the test piles under static loads and without a maintained load were monitored to investigate the effect of thermo-mechanical and pure thermal loads on the energy piles, respectively. Conventional pile load tests were applied before and after the application of thermal cycles. The results of the pile load tests are compared to evaluate the effect of temperature cycles on pile capacity.IntroductionEnergy piles are deep foundation elements designed to access and exploit the relatively constant temperature of the ground and its heat storage capacity for efficient heating and cooling of buildings. The deep foundation elements that are already in place for structural support are integrated with adsorber pipes to perform as heat exchangers connected to ground source heat pump (GSHP) systems. With the use of energy piles, the heat energy is fed into and withdrawn from the ground for cooling in the summer and heating in the winter, respectively.Energy piles present an innovative way to harvest near-surface geothermal energy and to provide lower carbon emissions, however, there are still pending question on their performance. During heating-cooling cycles, energy piles experience temperature changes, which result in expansion or contraction of the piles."

Jan 1, 2017

By Hoke M. Garrett

The domestic cement industry demands about 550 trillion Btu annually, at a time when reduced fuel use has become a necessity due to the energy shortage. In terms of the overall power picture, that 550 trillion Btu, which includes both fossil and electrical energy, means about 0. 870 of all energy consumed in the U. S. The various factors influencing reduction of this energy consumption are the subject of this paper. Nationally, the energy shortage is being tackled on two fronts--increasing supply and reducing demand. Making cement consumes energy; therefore, the industry cannot join the effort to increase the energy supply except indirectly as noted later. Demand can also be attacked on two fronts--by reducing cement consumption or by reducing the amount of energy required to make cement. The following discussions on reducing cement industry energy consumption center briefly on the prospect of reducing cement consumption followed by a broad evaluation of the potentials for improving cement-making thermal efficiency.

Jan 1, 1974

By John E. Leitch

The cost of corrosion as measured by such cost components as the renovation or replacement of coated steel, or the use of expensive coating systems on steel, is considerable. Extrapolating from figures for the USA would place the overall cost of corrosion for South Africa as a figure of the order of magnitude of something over 1% of the GNP. This is a sizeable amount, of which costs associated with atmospheric corrosion would be a significant proportion. The corrosivity of an atmosphere can be defined as the ability of the atmosphere to cause corrosion in a given metal or alloy (International Standards Organization [1]). The ISO Standard 9223 specifies the key factors in the atmospheric corrosion of metals and alloys, and defines categories of corrosivity on the basis of these factors. Prior to the publication of that ISO standard, Callaghan published the results of his twenty-year exposure programme and his excellent corrosivity map of Southern Africa [2]. The present author published updates of the corrosivity map in 1999 [3] and again in 2003 [4]. The summary of the individual areas of corrosivity around Southern Africa was published in the latter paper, and is reproduced here as the following TABLE 1. Of significance in TABLE 1 are the numerous regions of very high corrosivity (C5 or beyond), particularly the rural West Coast shoreline, the North East Coast (KZN) shoreline, and the coastal cities Cape Town, Durban and Richards Bay. The corrosivity map as published is obviously based on much extrapolation as only a small number of points have been measured. During the past three years further measurements have been made, mostly however at the same sites in order to give greater reliability and to monitor long-term trends with changes in pollution. These two aspects are incorporated in this update. There has become available a greater amount of air pollution data for centres in South Africa than was the case some years ago. In this present paper the pollution data are used to extrapolate the corrosivity over areas where little or no direct corrosivity measurement has been made. This methodology is described in ISO 9223.

Jan 1, 2006

By A. Visnapuu

The Bureau of Mines has upgraded high-iron domestic chromite concentrates by a carbonyl process. The upgraded chromite concentrates show as much as 10 wt pct higher Cr203 content and up to a threefold in-crease in the Cr:Fe ratio, compared with the starting concentrates. The high-iron chromites were first reduced to convert the iron oxides to the metal, and then treated with CO at elevated pressures and low temperatures to convert part of the metallic iron fraction to iron pentacarbonyl. Carbonylation was accelerated by the addition of H2S in small quantities. The iron pentacarbonyl was extricated from the con-centrate in the pressure reactor during carbonylation by a CO sweep through a pressure-reducing valve and passed through a decomposer at atmospheric pressure to convert it back to iron metal and CO. CO pres-sure, temperature, promoter trends, and other factors enhancing iron pentacarbonyl formation are presented.

Jan 1, 1985

By Bailey, Lewis Newton

Bailey, Lewis Newton, Master Engineer, Senior Oracle, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia, at Camp Merritt, N. J., on April 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Ballamy, John H., Capt., 103d Engineers, killed in action near Fismes, Aug. 9, 1918. Burt, Andrew, died in active service, 1916. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on October 7, 1915. Dougall, Ralph, 4th University Co., Princess Patricia Regiment, killed in action early in the war. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M. killed in action on October 12, 1917. Gorman, Thomas C., Lieut., Canadian Engineers, killed in France, Mar. 18, 1918. Hague, William, 1st Lieut., Engineer Officers' Reserve Corps, died in active service, Jan. 1,, 1918. Hall, William T., Capt., Royal Flying Corps, killed in action, May 19, 1917.

Jan 11, 1918

By Sergey Dyachenko

"Following the adopted strategy for making the production modern, efficient and environmental friendly the Company completed a stage of the integrated program aimed at reconfiguration of its processing capacity.Upgrade of the Talnakh Concentrator with commissioning of two start-up facilities (SF) allowed an increase of 30% in its ore processing capacity up to 10 mtpa. In addition to a new high-tech equipment installed, a new concentration process was adopted offering the main advantage of 25-30% reduction of sulfides in concentrate. New concentration technology enabled the total amount of produced nickel concentrates (from Norilsk and Talnakh Concentrators) to be processed at upgraded smelting facilities of Nadezhda Metallurgical Plant and allowed decommissioning of smelting capacities of Nickel Plant resulting in emissions reduction by 30%.Nornickel plans to boost the capacity of Talnakh Concentrator to 18 mtpa by 2022, after commissioning of the 3rd SF. This will provide a shorter route for ores transportation from Talnakh mines along with improvement of cost/performance ratio of ore processing through the usage of the modern equipment and optimized concentration flow scheme. Total capacity of Talnakh Concentrator will be sufficient to process ores from Talnakh deposits with planned upstream assets development taken into account. Volume of ore mined from Norilsk deposits to be processed at Norilsk Concentrator will be also increased.Upgrading the crushing section at Kola MMC Concentrator in 2015 provided finer particles of the crushed ore, resulting in 6.6% increase in specific capacity of ore mills as well as 1% higher recovery of non-ferrous metals due to improved liberation of ore minerals.In 2015-2017 the Company was actively engaged in optimization of existing process flow schemes and parameters of Kola MMC, new high-performance reagents were adopted for concentration process, namely, collectors, depressors, flocculants. These measures allowed the Concentrator to reduce its annual operating unit costs and ensure sustainable production of concentrate with the lower grade of the incoming feedstock.Launched in October 2017, Bystrinsky GOK’s Concentrator was 3D designed and received a range of advanced technological solutions.All design process procedures and technologies rolled-out at the Company’s concentrators were developed by Russian R&D institutes, with the key role of Gipronickel Institute, R&D Service of Kola MMC and Polar Division's in-house Engineering Support Centre."

Jan 1, 2018

By R. A. Jankowski

The U.S. Bureau of Mines has conducted a study to identify the sources of respirable dust and appropriate dust controls applicable to today's high tonnage longwall faces. The primary source of respirable dust identified is the cutting action of the shearer; however, the pct contribution of dust from coal transport through the stageloader/crusher was significant. This was primarily due to the high rate of mining, requiring rapid and constant coal transport. Techniques implemented for the control of shearer-generated dust included high drum water flow rates, deep cutting, shearer-clearer-type external water spray systems, and radio-remote control. The high water flow rates, and an enclosed stageloader with scrubber, were used to control dust during coal transport. No novel or effective control technology exists to control dust during support advance. Administrative controls for dust avoidance, and manual and batch-activated electro-hydraulic control systems were used to keep support movers out of the dust generated during support advance.

Jan 1, 1990

By Thomas R. Hightower

The Thunderbird plant was erected in Sullivan County in Indiana during 1958-1959. It was first put in operation in March of 1959. At the present time the source of the raw coal is from the Indiana No. 6 seam. The underground operation at present consists of two continuous mining units and two conventional units. The underground is all belt haulage and the first unit with which this paper is concerned is the slope belt. It is a 48-inch-wide inclined belt with 980-foot centers and a lift of 275 feet. The belt is powered with a 350 H, P, motor and has a rated capacity of 600 Tons per Hour. The belt is equipped with a Merrick Scale Company Weightometer, The raw coal moves from the belt to a 6'x12' extra heavy Allis-Chalmers Ripl-Flo equipped with 6" round-hole screens. The over product of the screen is fed into a 10'x20' long McNally- Pittsburg rotary breaker equipped with 4-l/2" round-hole screens. The oversize rock is discharged into a bin that is emptied with a refuse truck. The through-product of the breaker, along with the through-product of the Ripl-Flo, passes either directly to the McNally Giant washbox or to a 36" belt that transports it to a 1000-ton storage bin,' The change from either to the washbox or to the storage bin is made by use of a motorized gate controlled by the plant operator,

Jan 1, 1961

By M. S. Seehra, R. S. Pandurangi

"Investigations of the infrared spectra of crystalline and amorphous silica particles of different sizes (0.05, 5, 10, 15, 30, 45, and 260 um) in the range of 400-4000 cm-1 using Fourier transform infrared/photoacoustic spectroscopy we reported. The change in the intensity I of the signal with porosity e of powders follows the e/(1 - e) dependence for strong bands and e dependence for weaker bands as pre¬dicted by the theory of McGovern of al. For strong bands, I also follows the empirical relation I ~ D-n, where D Is the particle diameter in cm and n = 0.34-0.42. The anomalous positive frequency dependence of I on the modulation fre¬quency f observed for the stronger bands in the 45-pm and 260-pm particles Is believed to result from saturation. Some observations on the effect of changing the background from (carbon black) powder to pellet are also made.INTRODUCTIONSince the publication of the Rosencwaig—Gersho (RG) theory on the photoacoustic effect in solids (1, 2), Fourier transform infrared/photoacoustic spectroscopy (FTIR/PAS) has become an important technique for obtaining the IR spectra of surfaces and materials in their natural state (1-12). In the one-dimensional RG theory, the incident radiation, modulated at frequency f, is absorbed by the material to a depth pp = 1/B (B = absorption coefficient), thus setting up temperature variations in the material. These variations heat the adjacent gas/solid interface leading to the pressure fluctuations of the gas above the sample, which in turn is detected by microphone as a PA signal. The thermal wave originating from no deeper than the thermal diffusion length(2k/npcf) 1/2 in the material contributes to the PA signal (here k, p, and c are respectively the thermal conductivity, density, and specific heat of the material). Since u2, can be varied by varying the experimental parameter f, depth pro¬filing by PAS is possible and a number of papers on this subject have appeared in recent years (2-10). Another im¬portant phenomenon is saturation which occurs when the material thickness 1> u> us (1-12).The original promise of PAS for use with powder samples, without the need to ""prepare"" samples as in FTIR spectros-copy, has not yet been fully realized because of several com¬plications. Theoretical works by Monchalin et al. (13) and McGovern et al (14) showed that the interstial gas in the voids of the powders can act as amplifier and that, for the same mass, a finer powder is expected to yield higher PA signal than a coarser powder. Although in a number of earlier studies (15-21) an increase of PA signal with decreasing particle size has been observed, a quantitative check on the equations developed by McGovern et al. (14) has not yet been made. It is necessary to understand the particle size effects in PAS if the promise of PAS for IR spectroscopy of powders is to be realized. In this paper, we report results of a detailed study on the PAS of silica powders for the particle size range of 0.05-260 um and compare the results with theory (14). We have also investigated the frequency dependence of the variousIR modes in these powders and show that the saturation phenomenon affects at least some of the observations. Some observations on the effects of pellet vs powder background are also reported (22-24). Details of these findings are presented and discussed in this paper."

Jan 1, 1990

By G R. Ballantyne, V Souto, K Bartram

Particle sorting allows partially liberated minerals to be separated prior to energy intensive fine grinding. Sensors select particles for separation and air, water or mechanical ejectors are used to physically deflect those selected. To achieve effective separation there has to be sufficient liberation, accurate detection and presentation of a separated monolayer of particles. These three physical constraints determine the particle size limits, the sorting technology utilised, the separation efficiency, and the throughput that can be achieved. The combination of all these factors controls the effective limits on the degree to which sorting can reduce the specific comminution requirements and increasing energy efficiency. This paper will explore two case studies: the application of sorting in base metal mining and precious metal mining.CITATION:Ballantyne, G R, Hilden, M, Bartram, K and Souto, V, 2018. Characterising energy efficiency of particle sorting, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 531–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By P. G. Barnard

The Bureau of Mines investigated the effects of various additions of rare-earth metals or rare-earth oxides on the mechanical properties of cast and wrought plain-carbon steels. Rare-earth metals, as misch metal, were added to medium-carbon steel in amounts to 0.70 weight-percent; rare-earth oxides, as a commercial mixture, were added in amounts to 1.50 weight-percent. The melting and casting of conditioned steels were done in a vacuum-induction furnace, to avoid formation of oxides from the melting atmosphere and to pro-vide better control over chemical composition. At room temperature, data for tensile strength, yield strength, elongation, and hardness of cast and wrought steels were obtained by standard testing equipment and procedures. Impact tests were conducted on as-cast steel specimens. The greatest amount of tensile ductility and impact strength was obtained in as-cast steel with 0.50 to 0.70 weight-percent misch metal additions. No significant improvement on mechanical properties was indicated in wrought steels containing rare-earth metal additions in the range from 0.10 to 0.70 weight-percent. In general, the rare-earth oxide additions up to 1.50 weight-percent had little effect on the tensile properties of steel in the cast, wrought and annealed, or wrought and normalized condition.

Jan 1, 1967

By W. J. Dolinar

The U.S. Bureau of Mines implemented the Fe2+ /Fe3+-SO2 anode reaction in a Cu electrowinning cell with full-size electrodes. Electrowinning was conducted using industrial electrolyte at 258 A/m2 (24 A/ft2) and 40 'C. Manifold injection of electrolyte provided circulation between the electrodes. Five-day operation using an optimized manifold gave an average cell voltage of 0.94 V at 89% current efficiency, which amounted to an energy savings of 2.82 MJ/kg (0.355 kW-hr/lb) compared to conventional electrowinning. Acid misting was completely eliminated, and SO2 concentration 23 cm (9 in.) above the cell averaged 0.06 ppm.

Jan 1, 1995

By Jeff Fontana, Daniel Ebin, Eric Westergren, William Currier

The PMott MacDonaldlane Train Tunnel West Extension (PTTWE) Project at HartsfieldJackson Atlanta International Airport includes the extension of the existing automated people mover system and terminal renovations at the baggage claim station. To assist with design, pricing, and assessment of risk on this progressive design-build project, 3D design models were prepared to increase visibility into realities of construction. This paper will focus on the original intent of the models and explore the additional, unforeseen value they provided throughout the design and construction process.

Dec 1, 2022