Search Documents

Laboratory trials were performed in an induction furnace to study droplet formation during lance blowing. Compressed air was blown on a molten iron bath consisting of iron alloyed with carbon and silicon. Steel droplets were collected using a specially designed sampler. The average steel droplet composition and the oxide layer thickness were determined using scanning electron microscopy combined with energy dispersed spectroscopy. In addition, the concentration gradient of elements was determined using a microprobe. It should be noted that a special technique had to be developed in order to prepare the droplet sample. The size distribution and composition of the droplets was also determined using the microprobe. It was found that the carbon content in the droplets was lower than the carbon content in the bulk.

Jan 1, 2006

By J. L. Schroeder, W. G. Talman

EXPERIENCE has shown that certain known natural conditions and other indefinite characteristics combine to make a mining area vulnerable to mountain bumps. Some of the known conditions are heavy overburden, an overlying stratum of strong non-elastic rock, a structurally strong coal seam that does not crush easily and yet is the weakest stratum in the series, and a floor stratum of more than ordinary firmness. The indefinite characteristics could include resistance of top or bottom of a coal seam to lateral flow, effect of immediate top and bottom strata, nature of the coal seam, and other factors about which very little is known. It is in this area that exhaustive study is needed to achieve positive control of the dreaded mountain bump hazard. In the Gary district, West Virginia, two of the five operating mines have areas known to be vulnerable to mountain bumps.These are the No. 2 and 6 mines, which are working the Pocahontas No. 4 coal seam. In this area the seam is overlain at a zero to 10-ft interval by the massive Eckman sandstone, which is about 100 ft thick in the vulnerable areas. Total overburden, consisting of shale, coal seams, and sandstones, ranges from 700 to 1400 ft where bumps have occurred (Fig. 1). The coal seam is 4 to 8 ft thick and has a weak columnar structure of very soft and spongy or woody coal. The immediate top is either the Eckman sandstone or hard shale, both of which provide generally good roof conditions for mining operations. The bottom ranges from medium to hard gray shale. The incidence of bumps in the Gary district dates from about 1930 and can be correlated to some degree with the increased rate of extraction attained with mechanical mining. During early years of operation at the No. 2 and 6 mines, most of the work was development and under comparatively light cover. As overburden became heavier, together with an increasing percentage of coal coming from pillar extraction, mountain bumps began to occur. Before 1945 they were much less severe than in later years, and because there were no injuries or fatalities, no records were kept. But by 1951 the incidence of bumps had increased to such extent that it became evident a mining system would have to be designed to eliminate or at least minimize these occurrences. Drawing on experience with modified versions of old systems and certain characteristics peculiar to the Pocahontas No. 4 coal seam, the district mining engineer, Martin Hayduk, outlined the essential factors for bump control in the Gary district. These control factors indicated: 1) The highly stressed area, which lies within the limits of convergence effects, moves at approximately the same rate as the retreating pillar line. 2) There is a decided softening of the periphery of blocks which is greatest and deepest on the gob side. 3) Blocks less than 45 ft wide never have been known to bump in the Pocahontas seams. Fig. 2 shows the mining plan based on these observations—a thin-pillar system with a minimum of secondary development. It was recognized from the start that the Hayduk system had certain limitations. When pillar work backed up to an inevitable surrounded block it was no longer applicable; also, burnt bottom and/or unknown factors reduced the system's effectiveness in certain headings. Since there was no way to eliminate the loaded block, it was decided to experiment with auger drilling to attain controlled release of this stored-up energy. The decision to auger was made after consideration of three separate plants, which were: 1) To cut the solid block into pillars of maximum size by driving away from the fracture line and at such a distance outby that development

Jan 1, 1959

By J. Asfahani

"The Schlumberger configuration used in geoelectrical sounding is slightly adapted here to obtain reliable data for both shallow and deep penetration depths from the same survey. In this configuration, two kinds of current electrode half-spacings are used: the first enables construction of vertical electrical resistivity sounding (VES) curves for shallow depths (<50 m), and the second for depths =250 m. For a given VES location, two field curves are measured and interpreted using two standard approaches. Practical characteristics of such a modified configuration are illustrated with two field applications in Syria. The first aims to characterize the structure of Quaternary and recent deposits in the Al-Ghab depression region, and the second deals with exploration for phosphatic sedimentary units in the Al-Sharquieh mine. La configuration de Schlumberger normalement employée dans les levés géoélectriques a été légèrement modifiée afin d’obtenir des données fiables à faible et forte profondeur durant le même levé. Dans cette nouvelle configuration, deux types de demi-espacements des électrodes sont utilisés : le premier permet le développement de courbes de sondage de résistivité électrique verticales (REV) pour les faibles profondeurs (<50 m), et le second atteint des profondeurs =250 m. Pour une localité REV donnée, deux courbes de champs sont donc mesurées et interprétées grâce à deux approches standardisées. Les caractéristiques pratiques de cette configuration modifiée sont illustrées par deus exemples d’application en Syrie. Le premier vise la caractérisation de la structure des dépôts Quaternaires et récents de la région de la dépression d’Al-Ghab, et le second traite de l’exploration pour des unités phosphatiques sédimentaires à la mine Al-Sharquieh."

Jan 1, 2009

By Robert Stefanko

The widespread and increasing use of electrical power for mechanized power has made a tremendous impact on the coal mining industry. It is probably the single most important factor influencing the productivity of a coal mine. In fact, as a part of a study of 62 coal mines in Pennsylvania and northern West Virginia, plus information that was obtained from other sources, it was possible to show a direct correlation between the rise in the use of electrical power and mine productivity, Figure 1. This increased power demand has not always been achieved through proper planning and a careful evaluation of all design parameters, many of which are not even recognized. The result has been increasing problems in power distribution and utilization establishing the need for scientific studies including considerable underground measurements. Because the cost of power for ton of coal produced is generally a relatively low value, inadequate attention is paid its distribution and utilization. Furthermore, a poor system of records and a lack of adequate measurements add further to a paucity of statistical evidence that would permit a rational analysis of overall power costs. However, the direct cost figure alone is highly deceptive; of much greater value is the indirect costs associated with the use (or misuse) of electrical power underground. Success in highly mechanized mining correlates directly with equipment utilization. Today&apos;s machines have tremendous potential capacities but profits are measured in terms of performance and not potential. Thus the reliability of electric motors is an extremely important factor for consideration and the effects of all parameters should be carefully evaluated. Thus while studies are continuing on the evaluation of primary and secondary mine electrical systems with interesting results, this paper will be limited to reporting on the results of a study of a specific motor application.

Jan 1, 1972

To determine the optimal circuit configuration for gravity gold recovery consideration should be given to a range of factors in addition to the efficiency of the gravity circuit, including capital costs, ease of operation and impact on comminution. The most common gravity gold circuits utilise a centrifugal concentrator treating a portion of the hydrocyclone underflow. This paper will examine this option and alternative circuit configurations to illustrate the effect of various gravity circuit feed and tailings configurations on the equipment sizing, capital costs, operating costs, water balance, comminution efficiency and gravity gold recovery. The optimum circuit configuration can provide reduced capital and operating costs, maximise gravity gold recovery and improve comminution efficiency.

Jan 1, 2011

By Ahmad Ghahreman, James McNeice

Separation of rare earth elements (REE) is often achieved by acid leaching of mineral concentrates followed by subsequent solvent extraction (SX), to purify individual rare earth metals (REM). Cerium, the most abundant REE, is usually the largest component of these ores. Demand for less prevalent REE, such as praseodymium and dysprosium; have led to a market saturation and price collapse of cerium. One method of improving the economics of REE separation is to remove cerium from solution prior to SX. This is accomplished via the oxidation of cerium (III) to cerium (IV), which precipitates as cerium hydroxides. This study probes the efficacy of four oxidants; hydrogen peroxide, sodium hypochlorite, potassium permanganate, and Caro’s Acid with the goal of improving cerium removal whilst minimizing REE and reagent losses. The effect of oxidant type and dosage, pH, cerium concentration, and temperature on the kinetics of the process will be discussed.

Mar 1, 2018

By R. B. Khumalo, M. S. Nyarela, R. C. Nemathithi

Palabora Mining Company is one of the largest low-grade copper mines globally. The mine uses block caving for the extraction of the orebody. This paper enumerates the drawpoint loading strategies for the overall head grade improvements, particularly for a block that is nearing depletion. A comprehensive literature review of various considerations relating to improving productivity in block caving is presented to contextualize the draw control in caving. From this study, an optimized draw control strategy is presented, which focuses on three parameters that include grade distribution, loading compliance, and tonnage splits per sector. An empirical method based on the relational study between various parameters is used to outline the key criteria to be used in the optimization of drawpoint loading in block caving.

Nov 30, 2022

By R Butler

Contract m1n1ng in New Zealand developed in the coal industry and has become an element in the success of recently opened hard rock gold mines. At Martha Hill, the mining contractor is undertaking a wide range of activities from open pit mining, crushing, conveying, waste embankment construction and drainage.

Jan 1, 1991

By J. H. Canterford

The nickel industry in Australia has followed the general pattern apparent in many other regions - lots of ups and downs, successes and failures, but always plenty of challenges. Some of these can be attributed to local geographical and infrastructure factors, others to a healthy mix of corporate good luck and management countered by decisions that, in retrospect, were less than optimum. The roles of several entrepreneurs have certainly added plenty of spice! In terms of processing technologies, there was an initial heavy reliance on the use of "off the shelf&apos; commercially proven processes such as ammonia leaching of concentrates and mattes, and flash smelting. Over the past decade there has been an increasing dominance of plant modifications and process technologies that have been developed "in house" in order to enhance project economics and exploit lower grade and more complex resources. This presentation provides an overview of the past 40 years of the major developments in the Australian nickel industry and concludes with some guesses as to where we will be in another decade or so.

Jan 1, 2005

By Manuel Gomez

Low-temperature carbonization product yields for 129 coals representative of 12 Utah coalfields were estimated, using regression equations developed from heating value and proximate and ultimate analysis data. It was shown that yields of char, tar plus light oil, water of decomposition, and gas, as well as the gas volume and the heating value of the gas, could be predicted with reasonable accuracy. Published and experimental results from eight Utah coals carbonized at selected temperatures in the 4500 to 1,000° C range were used to determine the effect of temperature on product yields. Carbonization temperature, heating value) oxygen, and volatile matter of coal appear to be the principal variables influencing carbonization product yields. Data presented show that the heating value and the residual volatile matter in low-temperature char may be predicted using relationships developed from proximate analysis data for 220 coals.

Jan 1, 1967

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion (Li-ion) battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V and 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicate that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

Jan 1, 2024

By S. Kamalpour

It has been observed that the productivity of ferromanganese furnaces, and the stability of metal and slag compositions, vary considerably according to the type of coke used as reductant. However, the desired properties of coke for optimum furnace performance are not well understood. In this investigation, the behaviour of four cokes, which exhibited a wide range of performance in ferromanganese production, was investigated by means of laboratory simulations of reducing conditions in the furnace. The Stationary Charge in Controlled Environment (SCICE) technique was used to simulate the conditions in the furnace shaft. Batches of raw materials, mixed in the same proportions as used in practice, were heated at fixed rates to 900, 1100 and 1300°C then cooled. The mass loss was used as a measure of the degree of reduction. Conditions in the lower part of the furnace were simulated by means of melt-reduction experiments in which lumps of coke were drilled out to form crucibles in which enriched ferromanganese slags were reduced at 1500 and 1550°C then cooled. An examination of the raw materials and the cooled, reacted charges using a variety of analytical and characterization techniques enabled the sequence of reaction and changes in morphology of the raw materials to be followed. This enabled an understanding of the behaviour of the cokes during reduction to be developed, which was then used to explain the observed performance of the cokes in practice. By relating the observed behaviour of the cokes in the laboratory tests to measurable properties of the unreacted cokes and to their observed performance in practice, it was shown that to achieve high productivity and good furnace performance, cokes should be selected to have moderately high reactivity towards CO2 (Boudouard reactivity) relative to conventional iron blast furnace cokes.

Jan 1, 2004

By Laura Steeves, Inoka Eranda Perera, Jhon Silva, Arend Spaeth

"This paper reviews the main concepts ruling the design, implementation and performance of active explosion barrier systems for underground coal mines in the USA. The document examines the parameters needed for the design of this type of system, such as overpressure and flame speed, suppressant deployment speed and duration time of the active barrier. The document also discusses the available solutions for gassy mines and the concepts behind the selection of machined mounted and roadway active explosion barrier systems. The paper includes a review of active explosion barrier systems developed in the USA and South Africa. The paper provides an overview of the current status of this technology in the underground coal mining industry in the USA, and the possible implementation of such systems. The paper concludes with the identification of the future work needed for the successful implementation of the systems in several conditions to enhance the safety of underground coal mine operations and to provide more tools to the miners for their safety.INTRODUCTIONUnderground coal mine explosions can be addressed in two ways, through prevention or mitigation. The United States mining industry practices have emphasized the prevention of explosions in underground coal mines, with little being done to mitigate the explosion once it occurs. Despite successful practices for the prevention of underground coal mine explosions in the US, the threat of an explosion does still exist. Other mining countries around the world have developed and implemented mitigation systems such as active explosion barriers in their underground mines. In the 1970s, the United States Bureau of Mines (USBM) carried out extensive research on the use of active or triggered explosion barrier systems in the US; however, they are not currently used.Explosion barrier systems do not prevent explosions but mitigate the propagation of the shockwave and flame to other areas of the mine. The use of active explosion barrier systems enhance the safety of underground coal mines. Active or triggered explosion barriers will detect the arrival of the shockwave or flame front of the explosion and release inert material to suppress or extinguish the flame. The technology required for active barrier systems is readily available based on their presence in other mining countries and must be adapted for their use in US coal mines. The adaption must consider the coal dust and methane concentrations in US coal mines, the mine geometry, and the mining equipment used."

Jan 1, 2019

By Steve Dubnewych, Jon Kaneshiro, Calvin Jin

The Joint Water Pollution Control Plant (JWPCP), operated by the Sanitation Districts of Los Angeles County (the Districts), treats wastewater generated by over3 million people and processes wastewater solids generated by over 5 million people. The JWPCP Tunnel and Ocean Outfall Project, if constructed, would be one of the major marine outfall projects in the world. The new tunnel and ocean outfall system would provide relief to the existing outfall and allow inspection, maintenance, and repair of the existing tunnel and outfall system, portions of which were constructed as early as the 1930s. Geologic conditions are challenging along the alignments within the study are a being considered. Conditions include saturated alluvial soils, weak sedimentary rock, mixed face conditions, and squeezing ground conditions. Other significant challenges include the potentials for encountering up to 11 bars of water pressure, crossing seismically active faults, and encountering gassy and contaminated ground conditions. This paper discusses the details of the proposed project and the associated challenges.

Jan 1, 2007

By Robert C. Dyni

This report details the investigation of multiple-seam longwall subsidence conducted by the U.S. Bureau of Mines from 1978 to 1989. A field investigation monitored ground surface movements over four upper-seam longwall panels and six lower-seam panels. The characteristics of the subsidence occurring as a result of mining these panels are examined; in particular, the angle of draw, subsidence development, total magnitude and areal extent, and critical width are evaluated and discussed. Comparisons are also made between the characteristics of multiple-seam longwall subsidence and single-seam longwall subsidence that occurred at the same site.

Jan 1, 1991

By Kumar M. Lyer

The channel reactor for ferrous and nonferrous processing has been modeled as a combination of ideal reactors. Cold model studies simulated the counter-current flow of slag and matte (or metal) with high-strength submerged gas injection. A composite model has been developed which describes the mass transfer between the two liquid phases, including the transfer of minor elements. The residence time for the matte droplets in the matte/slag emulsion is compared with the settling rates for the matte droplets in the slag to determine their relative importance in the mass transfer between matte and slag. The governing equations for mass transfer have been developed using correlations for the mass-transfer coefficients in the continuous and dispersed phases. An application of this scheme to a typical copper smelting system is presented.

Jan 1, 1993

By B. Anameric

The pig iron nugget process is gaining in importance as an alternative to the traditional blast furnace. Throughout the process, self-reducing?fluxing dried greenballs composed of iron ore concentrate, reducing-carburizing agent (coal), flux (limestone) and binder (bentonite) are heat-treated. During the heat treatment, dried greenballs are first transformed into direct reduced iron (DRI), then to transition direct reduced iron (TDRI) and finally to pig iron nuggets. The furnace temperature and/or residence time and the corresponding levels of carburization, reduction and metallization dictate these transformations. This study involved the determination of threshold furnace temperatures and residence times for completion of all of the transformation reactions and pig iron nugget production. The experiments involved the heat treatment of self-reducing?fluxing dried greenballs at various furnace temperatures and residence times. The products of these heat treatments were identified by utilizing optical microscopy, apparent density and microhardness measurements.

Jan 1, 2007

By A. Desbiens, M. Maldonado, R. del Villar, Aguilera. R.

This work details the application of a multiple model approach to estimate frother concentration in flotation processes. The methodology consists of identifying a set of linear dynamic models representing the effect of gas rate on the collection-zone gas holdup at different known frother concentrations (calibration step). An adaptive law is then obtained using Bayes&apos; rule to evaluate the conditional probability that each model represents the observed system behavior. In this way, a frother concentration estimate is calculated as a weighted sum of model probabilities and their associated (known) frother concentrations. Experimental results conducted in a two-phase system using Dowfroth250C are promising. Modeling and analysis for MIBC frother are also provided.

Jan 1, 2009

By R J. Soriano, S Ciutina

The Masbate gold deposits are situated on the island of Masbate, 350 km south of Manila. A new plant was commissioned in April 2009. The grinding circuit consists of one semi-autogenous (SAG) mill Ø9.75 m × 4.27 m, two ball mills Ø5.6 m × 7.1 m and a pebble crushing circuit, which is usually called a SAG-ball mill-crusher configuration. The SAG mill was originally equipped with radial pulp lifters. The mill runs at fixed speed of 10.9 rev/min, which is approximately 80 per cent of critical speed (per cent CS). Due to the high speed of the mill the original radial design pulp lifters presented a high volume of recirculating load inside the chamber and consequently heavy wear on the outer circle (bottom pan).In order to address the high wear on the pulp lifters a number of avenues were considered in early 2011. The chosen solution was to change the geometry of pulp lifters from radial to curved design. The pre-existing drilling pattern on the discharge end of the mill was a major constraint. A number of designs were considered. The selection of the most suitable option was to be made based on 3D discrete element modelling (DEM) and smoothed particle hydrodynamic (SPH) simulations.The original radial design and two potential solutions for curved pulp lifters were simulated with 3D DEM and SPH software. The main three objectives were predicting the charge dynamics, the expected wear patterns and discharge efficiency. One of the solutions was chosen and implemented during 2012.Observations carried on after installation of the curved pulp lifters have confirmed, as expected, a reduction in wear intensity on the outer pulp lifters. In addition to this, at early stages of operation with curved pulp lifters, the mill operator noticed a reduction in energy consumed by the mill with no detrimental effect on mill performance.This paper is intended to further study the effect of curved pulp lifters on mill energy consumption.CITATION:Ciutina, S and Soriano, R J, 2014. Curved pulp lifters – can they save energy?, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 109–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By G Corbett

Epithermal Au-Ag deposits form in the upper 1 km of the crust and are therefore best preserved in the less eroded Pacific rim arcs, although also recognised elsewhere. Two profoundly different ore fluid types give rise to low and high-sulfidation styles apparent as variations in ore and gangue mineralogy as well as characteristic zoned wall rock alteration. Low sulfidation epithermal Au deposits are derived from near neutral composite magmatic-meteoric fluids and divided into a group with a stronger intrusion association within arcs grading in time and space from: quartz-sulfide Au + Cu, to carbonate-base metal Au, and the epithermal quartz Au + Ag, whereas in strongly extensional settings the influx of meteoric waters promotes the development of chalcedony-ginguro banded Au-Ag epithermal veins. In the presence of continental crust particularly in Latin America polymetallic Ag-Au veins represent a Ag-rich equivalent of carbonate-base metal Au and passes upwards to chalcedony-ginguro Au-Ag style. By contrast high-sulfidation epithermal deposits are deposited from an acidic magmatic fluid which provided characteristic hydrothermal alteration by reaction with wall rocks grading outwards as mineral assemblages dominated by: vughy silica, alunite, pyrophyllite-diaspore, dickite-kaolin and then illite-smectite neutral clays. Au mineralisation is commonly refractory with enargite deposited dominantly later within the silica zone.Exploration for epithermal Au deposits benefits from an understanding of the controls to mineralisation which commonly give rise to the development of ore shoots with widest and highest Au grade ore zones. In low-sulfidation systems a combination of competent host rocks, dilatant structures, higher grade styles of mineralisation and efficient mechanism of Au deposition, contribute towards ore shoot formation. High-sulfidation epithermal Au systems occur in permeable volcanic and breccia host rocks which are linked by major structures to the magmatic source.CITATION:Corbett, G, 2013. Pacific Rim epithermal Au-Ag, in Proceedings World Gold 2013 , pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013