Search Documents

By Jr. Blanchette, Claude Bazin, Paul Blatter

"Reporting of the gold production during a month implies to estimate the mass of gold that is processed by a mill, recovered as dorés, lost to the tailings and the change of gold inventory within the plant equipments. Carbon in pulp and/or carbon in leach tanks may contain gold inventory as large as 72 000 g (2 200 troy oz) of gold which needs to be estimated from measurements obtained from sampling the material contained in a tank. Sampling and analysis introduce measurement errors that could be systematic and/or random. This paper examines the effect of measurement errors on the estimation of the gold inventory and on the variation of the inventory in the carbon in leach tanks of the Agnico-Eagle Mines Limited Lapa concentrator. Results of the analysis demonstrate that the inventory is measured with ±10% reproducibility, while the variation of inventory used for mass balance is known with ±300% reproducibility.INTRODUCTIONThe preparation of a production report implies to reconcile measured data with the constraint of material balance over the considered period of production. The sampling and data reconciliation problems were recently reviewed by Morrison (2008) and Jansen (2009a; 2009b). Typically a production report is prepared to cover a period over which the mass conservation hypothesis can be considered valid. In gold processing plants, the change of inventory can seldom be neglected and plays a significant role in material balance calculations. This is particularly true for circuits using carbon adsorption, where the complete cycle of carbon is measured in days.In a 2000 t/d gold ore processing plant, the inventory can be as large as 140 000 g of gold in gravity concentrator bins, carbon in pulp tanks and in the electrolysis circuit. This is equivalent to the mass of gold that fed the circuit during 10 days of operation with 7 g/t feed assays. The change of inventory may therefore strongly impact the production figures and especially the plant recovery at the end of a week or a month. Despite the financial impact associated with gold inventory, few publications are devoted to the subject. Bruington (1991) and Morrison (2008) discussed the problem and stressed the need for the development of reliable methods to estimate the gold inventory in carbon in pulp or carbon in leach circuits."

Jan 1, 2011

By Ronald G. Schmidt

AND SOME RIN UP HILL AND DOWN DALE, KNAPPING THE CHUCKY STANES TO PIECES WI' HAMMERS, LIKE SAE MANY ROAD MAKERS RUN DAFT. THEY SAY IT IS TO SEE HOW THE WARLD WAS MADE. Sir Walter Scott St. Ronan's Well - 1824 In the minds of many, geologic exploration has advanced little since the early nineteenth century. In truth, despite the development and refinement of new and potentially valuable technological tools, the approach or philosophy of the explorationist has received meager attention in professional literature. In many areas, the explorationist relies upon experience, subjective judgement and general intangible inspiration, often traveling together under the misleading pseudonym of "art," in achieving both an exploration plan and in making the myriad day to day decisions necessary to the execution of that plan. Without a solid, objective basis for decisions, exploration under this concept is little more than guesswork largely by intuition, and it is small wonder that many exploration programs flounder in a sea of over-expenditure inefficiency or fail to fulfill their expected goals within the funding which has been provided. From a rational management point of view, such a state of affairs is frustrating and inconsistent with the application of the same scientific principles which are presumed to be the basis for the exploration methods which are used. This somewhat presumptuous point of view cannot be extended as a general condemnation of the many exploration programs which are both technically and economically successful. On the other hand, the

Jan 1, 1968

By R. L. Grant

Study of the ignition of firedamp by explosives and the phenomena that underlie it is one of the long-term investigations of the Bureau of Mines. This report is the third in e series by the Explosives Branch summarizing the progress made at Bruceton in this study. The first paper described preliminary work on small, carefully controlled cannon shots the second discussed the results of suspended shots.5/ In this paper, experiments are described and interpreted that extend and support the concept of ignition presented previously. ACKNOWLEDGMENT The authors wish to thank Bernard Lewis, former chief, Explosives and Physical Sciences Division, and Guenther von Elbe, former chief, Physical Sciences Branch, Explosives and Physical Sciences Division, for their guidance and constructive interest.

Jan 1, 1954

By Sebastian Avalos, Julian M. Ortiz

The long-term mine scheduling is the optimal decision on how to extract and process the mining reserves. The resulting plan is mainly driven by economic, metallurgical, and geological factors. Accounting for their uncertainties leads to a robust solution and the feasibility for economic-risk quantification. In this work, we model the spatial uncertainty of grade distributions of multiple correlated elements, by using a multivariate morphing transformation. The result is a set of multivariate geostatistical realizations of the grades, which honor the conditioning data, the direct and cross variograms, and the multivariate statistical distribution, inferred from a set of samples. These models are the input in a reinforcement learning framework, adopted to train a deep neural network that considers the grade uncertainty and leads to an optimum mine plan after training using deep Q-Learning. Mining and processing capacities, as well as economic parameters and metallurgical constraints, are incorporated as the reinforcement learning environment rules. The method is validated on a real deposit, providing insights for future applications.

Jun 25, 2023

By Dae Young Kim, Sim Bo Kyung, Ebrahim Farrokh, Ki Chang Hyun

"TBM cutter life evaluation in abrasive granitic rocks is a very important issue, especially in pressurized face tunneling with mixshield TBM for which the planning of costly interventions becomes crucial. This paper presents an overview of methodologies for cutter life evaluation in rock. A comparative study is performed to indicate the predictability of cutter life evaluation methods based on detail data from the NS3 tunnel project in Singapore. A new model is developed based upon the cutter wear information of eight TBM tunnels from around the world. New methods are proposed to evaluate the optimum intervention interval length and the number of worn-out disc cutters for a tunnel project. Finally, two new laboratory tests in the evaluation of disc cutter abrasion, including a full-scale and a small-scale test, are introduced, and their test results are discussed. INTRODUCTION The issue of wear evaluation for hard rocks has been extensively studied in drilling and pavement industry. In this regard, several tests and evaluation methods have been proposed to estimate or evaluate the state of tool life (e.g. bit life for drilling). In the case of TBM tunneling, tool wear may depend on several factors such as mineral composition, strength, or type of cutting, but as the abrasion is usually the major mechanism for the tool wear in hard rock, the developed methods for cutter wear or cutter life evaluation are mostly based on the abrasion indices such as Cerchar Abrasivity Index (CAI). This paper attempts to review the major methodologies for disc cutter wear and life evaluation and to propose new methods to evaluate cutter life and intervention interval evaluation based on detail information of a mixshield tunnel project in Singapore as well as general information of some other projects from Iran, Italy, South Africa, and France. As the laboratory tests are crucial in the process of evaluation, two new lab tests are developed and used to inspect suitability of the new proposed model for disc cutter wear evaluation."

Jan 1, 2016

By C. W. Taylor, F. L. Martin

"THE DICTIONARY defines Metallurgy as the ""science or art of separating metals from their ores and refining them for use"". In these days, however, such a definition is not detailed enough.The modern science of metallurgy is based on two fundamental sciences, physics .and chemistry, and is sub-divided into two major fields: Process Metallurgy and Physical Metallurgy. These fields of metallurgy are now so comprehensive and involved that even the graduate metallurgist has to specialize in one or the other.In recent years, the relatively new science or technology of non• destructive testing has also entered the industrial scene, with tremendous impact and ramifications. So much so that, certainly, no .discussion on metallurgy can be complete without including some reference to it.Obviously, one paper cannot hope to cover in detail the relationship of the whole science of metallurgy to the mining industry. Consequently, only a very brief reference will be made to the field of Process Metallurgy, our major concern being with Physical Metallurgy and Non-Destructive Testing."

Jan 1, 1960

By Lv Guozhi, Niu Liping, Liu Yan, Zhang Zhiqi, He Jicheng, Zhang Ting’an, Dou Zhihe

"CuCr alloy can be extensively used as contact materials in integrated circuit, electrodes, electric contact and high strength conductor. We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The slags and CuCr alloy were characterized respectively by XRD and SEM. The results show that when the additive is Na3AlF6, the slag consist of Al2O3 and Cr. When the additive is CaF2, the slag consist of Al2O3, Cr, CaF2 and CaAl4O7. The inclusions in CuCr alloy are mainly Al2O3 and pores which disperse in Cu-rich zone and Cu-Cr phase interface. When 5% CaF2 and 5% KClO3 are added, there are fewer pores and inclusions, and the more better microstructure.1 IntroduceCuCr alloy is the contact terminal material with an eximious properties[1,2], which gradually replaces CuBi alloy becoming the first choice for contact terminal material in the medium and high power vacuum switch after the 1970s. The traditional preparation methods of CuCr alloy mainly contain powder metallurgy, infiltration process and vacuum electric arc melting methods. But the above methods exist some shortcomings, such as poor product quality, high cost of production, processes complex ect[3-9]. CuCr alloy is made by the thermit reduction self-propagating method, which uses CuO, Cr2O3 and Al as raw material to get the high-temperature melt, and then casts to manufacture CuCr alloy ingot, which response equation follows as:"

Jan 1, 2012

By A. Rojo, N. J. Ramirez, J. E. Salgado

"This work aims to characterize the plastics used in a handgrip located in the car interior body in order to improve its design process and be able to predict its behavior when the part is subjected to impact test involving human casualties.Through stress analyses at high speeds and a video camera set up (front and side view), the reduction of area of specimen was obtained from image analysis, allowing to get the stress-strain real curve of the material.Continuing the characterization process a set of impact test was developed, where standard lzod configurations were used in unnotched specimens. From these tests were gotten displacement curves and absorption energy estimations.The proposed testing procedure allowed the acquisition of force and displacement data through time at various strain rates which are indispensable for the characterization of dynamic events. Using a specimen with a special configuration has shown a more detailed dynamic behavior resulting into more accurate numerical analyses within the design process.IntroductionIn the design process, one of the many analyses which take place is the impact test of the designed part. Nowadays there are many software capable to do these kind of analysis and each industry use the one they think it is convenient for them, but also the selected software has mathematic models that help to find the solution and the simulation of the case of analysis. These are not the only considerations that a company has to take into account, other one is the type of information and data necessary to feed the software. For this study we are going to focus on the acquisition of these data.The mail reason of this work is that generally the supplier gives the card of the material with all the characteristics and information requested by the buyer, but all of that information is acquired by standard methods, but it is inconvenient when the materials are polymers."

Jan 1, 2011

By K. T. Valsaraj

The separation process called solvent sublation for the removal of two hydrophobic compounds (penta-and tri-chlorophenols) from the aqueous phase is discussed. A steady state mathematical model for the process is discussed. The process was conducted in a continuous countercurrent mode. The underlying mechanisms, theory and experimental details on the effects of process variables on removal efficiency are reported.

Jan 1, 1992

By Leland L. Mink

Open-pit mining is sometimes conducted in areas where the artesian pressures contained in aquifers underlying the pit's floor are great enough to cause floor heave. In order to reduce this pressure several methods are commonly used. One of these methods is a pressure relief well or depressurization wick. The wick consists of a borehole which is filled with gravel and cased at the surface. The wick is allowed to flow freely, thus reducing pressure near its location. The spacing and depth of these wicks can be determined by a simple analytical and graphical technique which considers the weight of material overlying the aquifer and the artesian force within the aquifer. An example of the technique using data from a Colombian coal mine is presented.

Jan 1, 1986

By A. John R. Hart

INTRODUCTION The use of precast concrete tunnel liners as the initial and final tunnel lining for transit systems has been a major consideration of designers for over three decades. The obvious benefit of building a tunnel that requires only a single pass in constructing the structural lining can provide the opportunity of saving both time and cost. This technique has had worldwide application in transit systems in London, Munich, Hong Kong, Toronto to name a few. In the United States precast liners were evaluated for use on the BART System in San Francisco in the early 1960's but did not provide sufficient confidence in the sealing capabilities available at that time. In 1976 it was decided to call for bids on the Lexington Market Tunnels in Baltimore with a precast concrete liner alternative for one of the tunnel drives. This option was selected by the owner and UMTA to provide a study evaluation for the benefit of the industry. HISTORY In 1983 Washington Metropolitan Area Transit Authority began calling for a series of bids on soft ground tunnels on the Green Line, which included the option of using precast concrete tunnel liners first as an alternative to fabricated steel tunnel liners. Over the years following, the precast concrete tunnel liners have become known as the conventional tunnelling system and, in the last year,

Jan 1, 1989

By Antonio Fabiano de Oliveira

The aim of the present research work is to study the influence of hard chrome covered skin pass cold rolling rolls using 2D/3D surface topography, i.e. roughness characterization. The common stochastic structure Shot Blast Texturing (SBT) does not meet all requirements related to the production line regards to the finished product. The Hard Chrome layer, applied on these SBT rolls, can improve the sheet surface quality and is of fundamental interest mainly for those steel mills that do not have another alternative to new surface structures such as those that may be provided by the EDT, LT, EBT, etc. methods. The function of the generated surfaces, obtained by these different methods is going to influence the tribological properties during the subsequent forming processes. On the other hand, they can increase the product final cost or require large investments to obtain such surfaces. The results here presented are in accordance with other recently published research work, showing that there is a relationship between these parameters, and that further detailed studies are needed.

Aug 17, 2017

Upon the recommendation of its Technical Committee, The Com-pressed Air Society has adopted the following definitions of, certain terms. Displacement.-The displacement of an air compressor is the volume displaced by the net area of the compressor piston. Capacity.-The capacity should be expressed in cubic feet per minute, and is the actual amount of air compressed and delivered, expressed in terms of free air at intake temperature and at the pressure of dry air at the suction. Volumetric Efficiency.-Volumetric efficiency is the ratio of the capacity to the displacement of the compressor, all as defined above. Compression Efficiency.-Compression efficiency is the ratio of the work required to compress isothermally all the air delivered by an air compressor to the work actually clone within the compressor cylinder, as shown by indicator cards, and may he expressed is the product of the volumetric efficiency (the intake pressure and the hyperbolic logarithm of the ratio of compression), all divided by the indicated mean effective pressure within the air cylinder or cylinders.

Jan 8, 1918

A new departure of unusual importance in Institute annals was in-augurated by the trip of President Philip N. Moore to the Local Sections at Nevada, Southern California, San Francisco, Seattle, Spokane, Montana, Utah, and Colorado. Everywhere the visit of the President was the occasion of an enthusiastic and successful meeting, which is reflected in the account, published under the different Sections in this and other Bulletins. The President also joined the members of the Columbia Section in their visit to Nelson, British Columbia, at the International Mining Convention, which was attended by mining engineers of Canada and the United States. The President of the Canadian Mining Institute, as well as the officers and members of the Western Section also attended this convention. For full particulars we recommend to our readers the ac- count of this very interesting meeting, which is given on another page of this. Bulletin. It is believed that this is the first meeting between the mining engineers of America and any other country since America joined the Allies. The Secretary of the Institute accompanied the President at the first four meetings and was expecting to attend the others also, but was called home by a death in his family.

Jan 7, 1917

By Robert Mensah-Biney

The loading characteristics of gold-tetrabromide species onto a weak-base resin, PAZ-4, were evaluated using a completely mixed batch reaction system. The time. to attain equilibrium loading was substantial, on the order of several days. However, abnormally high loading capacity values of 15 to 20 meq Au/g dry resin (1000 to 1300 kgAu/tonne) were attainable in 24 hours. The loading of gold-bromo species by P AZ-4 was visualized as consisting of two processes: (i) the rapid adsorption of [AuBr4r species by simple ion exchange mechanisms and (ii) reduction of [AuBr4r to metallic gold by an electron exchange mechanism. Elution of gold from loaded resin was feasible provided the resin had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the loaded resin. For the high loading capacities observed this option would appear to be cost effective.

Jan 1, 1991

By R. S. Dean

The careful work of Gross and Zimmerleyl has established the fact that the energy actually used in grinding is proportional to the new surface produced. This confirmation of Rittinger's law was made by crushing quartz in a frictionless drop-weight machine and determining the surface of the quartz by its rate of solution in hydrofluoric acid. The details of this procedure have been described adequately elsewhere and need not be repeated here. The resultant data furnish the only available basis for comparing accurately the efficiency of grinding machines. This method is so cumbersome experimentally that it has been little used. As an alternative all sorts of approximations have been proposed. The best of these is complete size analysis by sieving and elutria-tion. Such procedure is very lengthy and difficult to carry out accurately. Furthermore, any sizing method becomes very inaccurate for determining surface with very fine sizes where the ratio of surface to volume becomes very large. To avoid the lengthy and difficult technique of elutriation it has been proposed to estimate the size distribution below 200 mesh from various probability formulas. Such a procedure is at best an engineering approximation; at worst it is a mere guess. Some time ago Dr. V. H. Gottschalk2 found that the coercive forces of magnetite powders were directly proportional to the surface area, regardless of size distribution. It was at once apparent that this furnished a method for determining grinding efficiency quickly and accurately. The only requirement was a single determination of the relation between the work input of the Gross-Zimmerley drop-weight machine and the coercive force of the resultant crushed magnetite. For this purpose Ural Mountain magnetite in definite octahedra was

Jan 1, 1939

By R. S. Dean

The careful work of Gross and Zimmerleyl has established the fact that the energy actually used in grinding is proportional to the new surface produced. This confirmation of Rittinger's law was made by crushing quartz in a frictionless drop-weight machine and determining the surface of the quartz by its rate of solution in hydrofluoric acid. The details of this procedure have been described adequately elsewhere and need not be repeated here. The resultant data furnish the only available basis for comparing accurately the efficiency of grinding machines. This method is so cumbersome experimentally that it has been little used. As an alternative all sorts of approximations have been proposed. The best of these is complete size analysis by sieving and elutria-tion. Such procedure is very lengthy and difficult to carry out accurately. Furthermore, any sizing method becomes very inaccurate for determining surface with very fine sizes where the ratio of surface to volume becomes very large. To avoid the lengthy and difficult technique of elutriation it has been proposed to estimate the size distribution below 200 mesh from various probability formulas. Such a procedure is at best an engineering approximation; at worst it is a mere guess. Some time ago Dr. V. H. Gottschalk2 found that the coercive forces of magnetite powders were directly proportional to the surface area, regardless of size distribution. It was at once apparent that this furnished a method for determining grinding efficiency quickly and accurately. The only requirement was a single determination of the relation between the work input of the Gross-Zimmerley drop-weight machine and the coercive force of the resultant crushed magnetite. For this purpose Ural Mountain magnetite in definite octahedra was

Jan 1, 1939

By E. Berrezueta

Automatic digital phase imaging should yield unbiased and representative characterizations of gold ores. However, this is not a simple tusk due to low gold grade, fine grain size, possible complex mineralogy, nugget effect, etc. Using the same sections of a gold-rich ore, a critical test was performed using an optical microscope (OM) and an electron microscope (EM). In general, the two methods are consistent and useful for ore processing. There are some minor differences, such as the detection of very fine gold grains is enhanced by EM. Key words: Digital imaging, Gold ores, Mineralogy, Electron microscopy, Optical microscopy

Jan 1, 2003

By Wilbur I. Duvall, James F. Devine

7.4-1. Introduction. Ever since explosives were discovered and developed for mining purposes, there has existed the problem of determining what effect the air and ground vibrations resulting from blasting have on structures of various types. This problem is especially acute for surface operations such as open pit mines, quarries, and construction projects that are in the proximity of residential districts, scientific laboratories, or other vibration-sensitive structures. Because the general public is directly involved in the blasting vibration problem, it has been of major concern to local, state, and federal governments, as well as to mining and construction companies, explosive manufacturers, insurance companies, and scientific investigators. Consequently, many investigations have been conducted, both in this country and abroad, on the effects of air and ground vibration on residential and other structures. E. H. Rockwell made some of the first studies in this country on the vibrations produced by blasting and the effect that these vibrations have on structures (18). In his publications, he stressed the need for measuring the vibrations from quarry blasting in order to establish the level of vibration as a function of charge size and distance. The concept of a damage criterion for structures was developed shortly thereafter, and a displacement of less than 0.03 in. was considered safe. During the period from 1939-1942, the Bureau of Mines conducted an extensive investigation on the problem of seismic effects of quarry blasting. This work, summarized in Bulletin 442 (20) was the first major effort for establishing damage criteria for residential structures based on experimental data. An acceleration of less than 0.1 g was considered safe, 0.1 to 1.0 g was caution, and greater than 1.0 g was damage. This work

Jan 1, 1968

By Russell S. Sage

THE electric motor has steadily replaced the steam and air engine for use in mine hoists, until today a new installation with other than electric drive is a rarity. Much existing steam-driven equipment has been changed over to electric drive. Driving power has grown in capacity since the initial electric unit rated 10 hp installed at Aspen, Colorado, in 1888, to 3000 hp and 4000 hp in the United States, and to 5500 hp in Canada-the largest in the Western Hemisphere. Electric installations now total in the thousands of units, a growth largely made possible by the development of large central electric-power stations and the extension of electric-power service to more mining areas.

Jan 1, 1949