Search Documents

By D. C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required placement of approximately 3,000,000m3 of fill over a P1an area of approximately 600,000m in irregular terrain with relief of up to 40m. Earthwork construction was completed in approximately six months using mine waste which was placed in 4 to 6m lifts using mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10m to enable development of a mat and additional resistance to possible differential settlements under dynamic (earthquake) conditions. A single 80 mil (2mm) HOPE liner was used below the leach pads and this was protected from the loading and unloading equipment using an engineered liner system consisting of screened sand, gravel and silt from local sources as the bedding and cover layers, and a heel of screened gravel and primary crushed low grade ore. Settlement monitoring, field testing and subsequent assessments of liner performance have indicated an adequate design was achieved and the project proceeded with considerable savings in time and construction costs.

Jan 1, 1995

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Underground mining environments bring occupational health and safety issues with some severe dangers such as mine disasters like explosions. During such events, miners might escape using main access openings, or find a safe haven like refuge alternatives (RAs) to wait and be rescued and evacuated to the surface. In this paper, RAs are explained with their early and current applications. A classification as permanent and portable is explained depending on the conditions and their abilities. This classification is followed by the utilization and survivability of RAs with the requirements and recommendations of the main mining countries. Based on the utilization and survivability constraints, basic human requirements, waiting for a rescue team, and the required physical specifications of RAs during the events are analyzed in detail for various countries with their regulations. Among these, the specification, resistance to the explosion, is discussed in particular, and the studies in the literature are examined in terms of structural deformation. The highest deformed zones, the beneficiation of reinforcing steel components such as stiffeners, and the simulation approaches are investigated through this review.

Sep 24, 2022

By Oliver Bowles

The wire saw, introduced by the Bureau of Mines about two years ago, has revolutionized slate quarrying in Pennsylvania. The success of the saw since its early accomplishments has become greater and greater as the equipment has been perfected and skill acquired .in its use. In the first test made, a cutting rate of 9.7 square feet per hour was attained; in the next four cuts, made early in 1927, the average rate of cutting was increased to 12.8 square feet per hour; in 1928 a maximum of 34 square feet per hour had been attained, with a general average of about 20 to 25 square feet, The wire saw is now regarded as essential equipment in practically all of the quarries in the Bangor, Pen Argyl, and Windgap districts. The wire saw consists of a three-strand steel cable of 3/16 or 1/4 inch diameter running as an endless belt. The driving pulley is a 40-inch double-groove cast-iron sheave. A tension pulley supported by a frame mounted on wheels may travel back and forth on a short track. A weight of 800 to 2,000 pounds gives the desired tension on the wire. The driving units consist of electric motors with direct-drive compactly enclosed gear reduction, or double-belt speed-reduction units; the former is preferred. Silent chain and. pinion gear reductions are used to a limited extent. The travelling speed of the wire is about 15 feet per second. The driving and tension equipment are shown in Figure 1, A.

Jan 1, 1929

By H. O. Olsen

"GeneralTHE IRON ORE at Marmora is a replacement deposit of Precambrian limestone and is overlain with Palaeozoic limestone. It is a low-grade magnetite deposit and the ore will require concentration be-fore it can be used economically for the production of iron and steel.Present plans estimate an annual production of 500,000 tons of concentrate in the form of pellets. This will require mining approximately two million tons of ore and\ waste annually. Shipment of pellets from Marmora to a ship-loading dock at Picton will be made by rail on a year-'round basis. Shipments from Picton to the Lackawanna plant of the Bethlehem Steel Company at Buffalo, N.Y., will be carried on during the Lake shipping season.LocationThe mine, located a mile southeast of Marmora village in Hastings county, Ontario, is 31 miles north of Belleville and 3•7 miles east of Peterborough. Marmora is 130 miles from Toronto and 150 miles from Ottawa. Highway No. 7 passes half a mile north of the mine and Highway No. 14 half a mile west of the mine. The Canadian National railways' branch line between Trenton and Bancroft passes through the property just east of the open pit.HistoryThe Ontario Department of Mines conducted an airborne magnetic survey of the district during 1948 and 1949. Maps of this survey were released to the public early in 1950. Bethlehem representatives carried out ground surveys in the Marmora area shortly thereafter and in June, 1950, commenced diamond drilling."

Jan 1, 1955

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, Matthew Gordy, Patrick Zhang

Waste phosphatic clay presents a difficult disposal problem and a significant loss of P2O5. Recent developments make this study on the use of phosphatic clay as a feed material for H3PO4 production worthwhile. (a) New data from Florida Industrial and Phosphate Research Institute (FIPR) suggest that the Bclay^ waste can be effectively treated by improved solid separation coupled with flotation to produce feed material for recovering additional phosphate. (b) The use of BOLI Flowsheet^ provides capability to predict performance of aqueous-based processes for a range of possible operating conditions. Using the new FIPR data and BOLI Flowsheet^ enabled the design of a new process that can potentially extend the usefulness of current P2O5 ore deposits. Predictions using OLI Flowsheet were able to identify process conditions that effectively overcome the difficulty of high Mg content of phosphatic clay. Estimated manufacturing cost in the current study lead to valuation of the P2O5 content of the phosphatic clay recovered/utilized at 60 to 70% of that of the phosphate rock feed material currently used. Phosphatic clay should be considered as a valuable material that is currently given zero value. The new FIPR data and BOLI Flowsheet^ enables the design of a new process that can potentially extend the usefulness of current phosphate ore deposits by extending the fraction P2O5 of recovered

By Omotayo Kalejaiye

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRL 20-L and Fike 1-m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface-weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1-m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

Jan 1, 2010

By D. Scott Scovira, Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1 ms increments up to 1500 ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits.

Feb 1, 2024

By Muhammad I. Kabir

The streamline method of recovery prediction reduces a two-dimensional problem to a bundle of one-dimensional ones. This paper presents the development and application of a novel scaling technique which, when used with a streamline model, causes s bundle of one-dimensional problems to further reduce to a single one-dimensional calculation. The one-dimensional calculation accounts for chemical-rock interactions and the streamline model for areal sweep. The scaling technique significantly reduces computation time, is readily modified to desk-top calculations, and can be applied to both absorbing and reacting species. The work was sponsored by the Interior Department's Bureau of Mines.

Jan 1, 1984

By W. T. lsbell

HERCULANEUM, MO., about thirty miles south of St. Louis on the Mississippi River, is the site of the lead smelter of the St. Joseph Lead Co. The lead concentrates come by rail from the Flat River district and from three properties in Madison County, Missouri; from the Balmat division in St. Lawrence County, New York; a small tonnage from the Tri-State district; and occasionally from the Aguilar property in Argentina. The average grade is 67 to 68 percent lead and 1 to 3 oz of silver. The bulk of the material is flotation concentrate, with some gravity or table concentrate. No secondary metals, outside drosses, or any materials high in bismuth, arsenic, or antimony are treated. All concentrate is received in box-caps and is unloaded directly from a trestle into the concentrate bins at the roaster plant. Flux, coke, and any miscellaneous lead-bearing material is either unloaded directly into bins or unloaded with a locomotive crane. All moving and switching of cars is done with two thirty-ton steam locomotives. Shipping facilities for the plant are provided by the Missouri-Illinois Railroad. Water for the plant and for fire protection is obtained from a dam built in a near-by creek. Drinking water both for plant and town is obtained from

Jan 1, 1947

By Peng ZANG, Qihang Liu

Experimental work was conducted to determine the relationships of coal char conversion with temperature and heat absorption. The results show that at an earlier stage of the coke forming process, lump coal would absorb large amounts of heat but the increase of high temperature strength of lump coal was not significant. Contrarily, the lump coal’s high temperature strength was greatly improved at later stage of coke forming process. A number of residual coal was found in most tuyere coke samples illustrating that the lump coals added in the melter gasifier were not completely transformed into coke when they arrived at the tuyere region. The results indicate that the improvement of lump coal’s high temperature performance is limited in the melting gasifier by the low coke forming rate which could become the core factor of fines generation of lump coal in the melting gasifier.

Jan 1, 2016

By A. M. Venter, C. W. Siyasiya, N. K. K. Arthur, M. G. Willemse, D. Marais

Although additive manufacturing is fast gaining traction in the industrial world as a reputable manufacturing technique to complement traditional mechanical machining, it still has problems such as porosity and residual stresses in components that give rise to cracking, distortion, and delamination, which are important issues to resolve in structural load-bearing applications. This research project focused on the characterization of the evolution of residual stresses in Ti-6Al-4V extra-low interstitial (ELI) additive-manufactured test samples. Four square thin-walled tubular samples were deposited on the same baseplate, using the direct energy deposition laser printing process, to different build heights. The residual stresses were analysed in the as-printed condition by the neutron diffraction technique and correlated to qualitative predictions obtained using the ANSYS software suite. Good qualitative agreement between the stress measurements and predictions were observed. Both approaches revealed the existence of large tensile stresses along the laser track direction at the sections that were built last, i.e., centre of the top layers of the samples. This in addition leads to large tensile stresses at the outer edges (corners) which would have the effect of separating the samples from the baseplate should the stresses exceed the yield strength of the material. Such extreme conditions did not occur in this study, but the stresses did lead to significant distortion of the baseplate. In general, the microstructures and spatial elemental mapping revealed a strong correlation between the macro-segregation of elemental V and the distribution of the β-phase in the printed parts.

Feb 6, 2023

By Lindsly. Ben E.

"The recovery or partial recovery of the oil remaining in oil sands after the usual methods of production have become unprofitable is perhaps the greatest problem in the petroleum industry today. The amount of this oil remaining in the sand is variously estimated by those familiar with the subject to be 25 to 90 per cent of the original content.2Lewis3 states, ""The estimate of 80 to 90 per cent of the oil left underground does not seem incredible.""It is estimated by the writer that approximately 91 per cent of the oil originally held in the Elliott pool, was still in the formation on January 1, 1924, and that it would take at least 12 years, at the 1923 rate of production, to further reduce this quantity by one per cent of the original content.The progress made in the oil industry during the past few years relative to the prevention of evaporation losses; to improvement in cracking processes, whereby the gasoline yield from many crudes has been doubled and trebled; to the increased recovery of gasoline from natural gas; and many other developments, remarkable as they are, can be applied only to that comparatively small portion of petroleum products which are raised to the surface. A device or process which would cut development costs to one-half would probably result in a much smaller profit to the oil industry, than the profit derived from an additional 10 per cent recovery of the total amount of oil in a pool. Various methods have been used and many others proposed, for the increase of oil recovery from normally depleted sands.In France, oil sands are being mined by means of shafts and galleries. In other places, notably the Bradford, Pennsylvania field, the yield has been increased by means of water flooding, wherein water is introduced into the sand to displace oil, and drive it to producing wells."

Oct 1, 1926

By William G. Pariseau

"This contribution describes linkage of stress concentration at the face of tabular excavations, for example, longwall coal mine panels, at a meter scale to surface subsidence at a kilometer scale. Joints are considered according to orientation and spacing at an intermediate scale. A new dual-node, dual-mesh technique based on first principles uses a multi-scale technique that allows for computing whole mine surface subsidence while also allowing for computational details of stress, strain and displacement about main entries and pillars, panel entries, and bleeder entries. The technique is implemented in a conventional continuous Galerkin finite element program that has been in use for many years.The advantage of the dual-node, dual-mesh technique is the capability to do a whole mine analysis that takes into account interaction between all sections of a mine where stress transfer over long distances is often the rule rather than the exception while at the same time allowing for details of stress concentration at working faces where caving is initiated and subsidence begins. The technique, outlined recently during ARMA 2014 (Pariseau, 2014), is applied to an underground coal mine in central Utah where mines are developed from outcrops in steep canyon walls. Meshes contain over 10 million, three-dimensional nodes; runtimes are typically overnight, as a practical matter. Results compare favorably with mine subsidence measurements made over a period of several years and show the capability of this new technique to provide useful design guidance for tabular deposits such as underground coal mines. The role of variability or uncertainty in strata properties is illustrated in element safety factor distributions about development, bleeder and main entries and pillars. Such details are new in this contribution. Energy tracking for mine-induced seismicity is also new. Results show a high correlation between number of events and failed elements and suggest a simple index to mine induced seismicity."

Jan 1, 2015

A direct comparison has been undertaken between laboratory wind tunnel experimentation and computational fluid dynamics simulation of a 3D manufactured analogue for a body of fractured broken rock, created with CAD/CAM techniques. Detailed descriptions of the ?design? of the analogue (using a discrete element analysis multi-body simulator), its manufacture (using computer aided design and 3D printing technology) and the laboratory experimentation (inserting the physical analogue into a laboratory scale wind tunnel) are presented. The agreement of the results of direct experimental observations on the manufactured analogue with the values from CFD simulations of those experiments justifies the utilization of a CFD environment for the practical investigation of geometric factors controlling air flow and heat exchange in complex assemblages of broken rock blocks. The ultimate goal is described, that of developing functional relations between bulk properties of such assemblages (such as their porosity and bulk density) and the low-level geometric factors that dictate the air flow behaviour, such as the equivalent perimeter length of the cross-sectional area available for flow, or average flow path tortuosity. A practical application area of the work in the mining context is also described; equivalent continuum air flow and heat transfer constitutive models developed on the CFD tool from such functional relations are useful in characterization of seasonal heat storage in large scale bodies (approximately 1 km3) of broken rock.

Aug 1, 2013

By C. Keefe, O&apos

Measurements of the quantity of entrained air within processes have challenged instrumentation developers for years. This is particularly true in the unique and demanding operating environment and applications seen in minerals processing. In minerals processing applications, entrained air plays a role in errors seen within nuclear density gauge measurements and in pumping efficiency. It is also the major component of flotation processes. The measurement of the quantity of entrained air, known as the gas void fraction, can now be performed from the outside of a process pipe through CiDRA?s patented passive sonar array-based technology. Within column cells, the need for a robust, no maintenance, accurate means of measuring the entrained air, known as gas holdup, has resulted in a submersible version of this technology. CiDRA?s meter technology calculates the gas void fraction by first measuring the speed at which naturally occurring sound in the process slurry propagates past an axial array of sensors. These sensors are incorporated in a band that is wrapped around the outside of the pipe, resulting in no process downtimes for installation and unprecedented reliability. A known relationship between this speed of sound and the entrained air captured in the form of bubbles within the slurry is then applied in CiDRA?s meter to calculate the gas void fraction. This paper will present the measurement technology, its operation, its calibration and its application in a variety of gas void fraction and gas holdup measurement situations such as pumping efficiencies, hydrocyclone operation, external sparging, and column cells.

Jan 1, 2008

Crystalline silica is the scientific name for a group of minerals composed of silicon and oxygen. The term crystalline refers to the fact that the oxygen and silicon atoms are arranged in a three-dimensional repeating pattern. This group of minerals has shaped human history since the beginning of civilization. From the sand used for making glass to the piezoelectric quartz crystals used in advanced communication systems, crystalline silica has been a part of our technological development. Crystalline silica's pervasiveness in our technology is matched only by its abundance in nature. It's found in samples from every geologic era and from every location around the globe. Scientists have known for decades that prolonged and excessive exposure to crystalline silica dust in mining environments can cause silicosis, a noncancerous lung disease. During the 1980's, studies were conducted that suggested that crystalline silica also was a carcinogen. As a result of these findings, crystalline silica has been regulated under the Occupational Safety and Health Administration's (OSHA) Hazard Communication Standard (HCS). Under HCS, OSHA regulated businesses that use materials containing 0.1 or more crystalline silica must follow Federal guidelines concerning hazard communication and worker training. Although the HCS does not require that samples be analyzed for crystalline silica, mineral suppliers or OSHA-regulated businesses may choose to do so if they wish to show that they are exempt from the requirements of HCS. Because crystalline silica is an extremely common mineral and the HCS will affect many mineral commodities, it is important then, that there be as clear an understanding as possible of what is and what is not crystalline silica, and where it is found and used, and how it is qualitatively and quantitatively identified. This primer is an attempt to accomplish this in as nontechnical a manner as possible. This primer will examine crystalline silica. Part I will describe, in nonscientific terms, what crystalline silica is and how we come in contact with it. Part" will discuss the regulatory decisions that have created new interest in this ancient and widespread substance and will present a nontechnical overview of the techniques used to measure crystalline silica. Because this primer is meant to be a starting point for anyone interested in learning more about crystalline silica, a list of selected readings and other resources is included. The detailed glossary, which defines many terms that are beyond the scope of this publication, is designed to help the reader move from this presentation to a more technical one, the inevitable next step.

Jan 1, 1992

By Jupneek Singh, Zachary A. Kiehl, Leila Safazadeh, Gareth Kennedy, Eleonora Widzyk-Capehart, Jeremy W. Ward

Mine workers are continuously exposed to a host of nonfatal stressors and potentially fatal hazards: noise exposure, excessive vibration, poor air quality, toxicant exposure, ignition of combustible gases, equipment-related accidents, and thermal heat stress. Wearable or portable sensors and contextual analytics provide a platform to unobtrusively collect and fuse multimodal health and safety data in real time to compute both acute safety and longitudinal health insights. This paper presents preliminary trial results, conducted by Simtars, VigiLife, Inc., and Queensland Mines Rescue Service, of the application of wearable sensors to monitor heat stress and other vital biometrics for mines rescue personnel.

Feb 1, 2024

By J. Chelsey Dawson

In presenting a thesis on this subject it is advisable to explain a few of the reasons for its seeming incompleteness. World progress has brought us to a position where approximations are not only to be condoned, but regarded as absolute essentials. Production in anticipation of demand is always accompanied by mistakes on the part of the producers. Only through trial and sometimes erring hypotheses may there be evolved the true course and theory upon which the steady triumphant march of world-wide industry depends. The average person likes to have everything placed ?before him in a clear and convincing manner. It is the impossibility of doing this which, in many cases, arises to confound the writer on shales. All that one can do is to present, as lucidly as possible, the known hypotheses' and theories on the subject and leave the reader to study and work out the truth for himself. Many theories have been advanced on the origin of oil-shales ; some may be correct in certain instances and not in others; however, the writer will attempt no decision as to which are and which are not correct, but .will merely point out the relative merits of each. The figures given for reserves of oil and shale in different countries are only approximations and give but a rough idea of the true conditions.

Jan 1, 1925

By L. T. Matthews, C. E. Loo

During sintering, porous ore particles are easily assimilated by liquid melt. Two simple models of the process are considered: the dissolution of a solid by a liquid and the penetration of a liquid into a porous solid. Laboratory sintering studies covering a range of experimental conditions were undertaken to characterise the assimilation of large particles of ore and flux by melts formed from different mixes of fines. For ores, the process appeared to be complicated by the detachment of fines from the ore surface prior to melt formation, according to the mass of adhering fines and surface roughness of the particle. This delayed the onset of assimilation and sometimes reduced it, although melt penetration was fast and effective. Studies using different temperature profiles suggested that the assimilation of haematite was controlled by the transport of Fe2O3 away from the surface of ore particles. The assimilation of limestone depended more on thermal conditions than on the three magnesia-bearing minerals considered. Changing the composition of the initial melt significantly altered the extent of assimilation of ores and limestone, but again had a less marked effect on the magnesia-bearing fluxes.

Jan 8, 1992

By Inoka E. Perera, Robert Hildebrandt, Gerrit V. R. Goodman, Krzysztof Cybulski, Zdzisław Dyduch, Michael J. Sapko, Marcia L. Harris

To prevent coal dust explosion propagations, rock dust needs to be lifted and suspended in the air with the coal dust during an explosion. The addition of anti-caking agents prevents caking of rock dust in the presence of water. Mining and rock dusting processes can frequently create alternating layers of rock dust and float coal dust on mine surfaces. For this test series, a thin layer of coal dust was distributed on top of a layer of either treated or non-treated rock dust in the Experimental Mine Barbara, Poland. The experimental results compare the effectiveness of treated and non-treated rock dusts to attenuate a propagating coal dust explosion initiated with either strong or weak methane explosions. Experimental results indicate that the treated rock dust performs better than non-treated rock dust in arresting a propagating explosion, especially in the presence of moisture.

Jan 20, 2020