Search Documents

By Robert F. Mehl

PROGRESS in the general field of nonferrous physical metallurgy during the past .year has been uneventful but healthy. A continued increase is apparent in the number of useful alloys and in the mechanical treatment and heat- treatment of finished metals and alloys nothing can hinder the multiplication of alloys or the diversification of their treatment as knowledge of the behavior of .alloys increases; as ternary and quaternary alloys are better understood, hundreds of new metal combinations with unusual properties may well be expected. Evidence of rapid progress is already at hand.

Jan 1, 1936

By M. -H. Fillion

"Geotechnical stability analysis and design in open pit mines requires access to representative geological, structural, hydrogeological, and rock mass models. The quality and quantity of collected geomechanical data used to build such models can have significant implications in the design of safe and economically viable slopes. Data collection is a continuous process throughout the life of a mine. The process starts from exploration to conceptual/preliminary feasibility, feasibility, design and construction, operations (early production/late production), and mine closure.As geomechanical data is often limited at an early stage of a project, the estimated variability of the geotechnical factors may be larger than the actual data variability. This can potentially result in a conservative selection of the pit slope angle. Collecting additional geomechanical data at later stages of the mine development may contribute to reducing the uncertainty associated with the geotechnical properties and a steeper slope angle may be used for the design. This can result in significant economic benefits.This paper investigates the impact of access to new data over time, following a series of geomechanical data collection campaigns, on design decisions. This is illustrated by comparing the resulting slope design, at three stages of the mine project, at a South African open pit mine. To demonstrate this, a series of slope stability analyses were performed using limit equilibrium tools. For each project stage, the slope angle design was modified until a similar probability of failure of 5% or less was obtained. The corresponding factor of safety distributions for each project stage were then compared to evaluate the impact of collecting additional data on the resulting slope design.The results showed that data variability can differ significantly from one project stage to another. Data variability may be greater at more advanced project stages (i.e. a wider distribution of the factor of safety). Furthermore, the results showed that, even for the cases with greater variability, steeper slope angles were possible at more advanced stages for the proposed design requirement (probability of failure < 5%). In this investigation, as more data became available, the uncertainty associated with data variability could be sufficiently reduced to allow the selection of less conservative slope angles. This can be used as a managerial tool in developing data collection strategies and allocating the necessary funds, and can lead to important economic benefits to the mining operation."

Jan 1, 2016

By J E. Gordon

For many years, it has been known that certain loud noises may, with prolonged exposure, temporarily or permanently damage a person&apos;s hearing ability. Pneumatic rock drills, al-though among the offenders, have, until recently, remained unaltered and unrestricted as to noise output. Now, there are drills available with higher rates of penetration and yet with noise levels reduced to those of previous models or less. Use of such drills, when proved to be superior in noise attenuation and of acceptable performance, should be encouraged in order to reduce future hearing losses to a minimum. People Have the Right to Hear P ERHAPS the earliest recognized indication of hearing loss due to industrial noise was the deaf-ness developed by the workmen in boiler factories. Here, the vibration set up in the shells by the riveting hammers gradually deteriorated the workmen&apos;s hearing, especially those whose job it was to hold the dollies inside the drum, where the sound is greatly intensified by reflection

Jan 1, 1963

By Ching-Yi Tsai

The effect of various constituents on the pyrolysis and combustion of a pulverized coal in an entrained-flow reactor has been inves¬tigated. Predicted time-temperature histories of the coal&apos; particles and experimental weight loss data indicate a strong coupling of heat and mass transfer to the pyrolysis and combustion rates. A higher combustion rate following ignition was observed as particle size was increased to 112 µm. This is related to a higher particle temperature after ignition for the larger particles. Although the heating rate prior to ignition decreases with increasing particle size, higher slip velocities and surrounding gas temperatures for the larger particles promote early ignition. The presence of liptinite in the coal increases the weight loss rate before and immediately after ignition. Similar behavior was observed for pyrolysis. Fractions of a HVA bituminous coal which were rich in mineral matter or semi-fusinite were found to have a higher heterogeneous char combustion rate than vitrinite rich samples.

Jan 1, 1984

By M. H. Moys

I had the good fortune to attend the above Conference which was held in Kanpur, India, on 11-15 December, 1995. The Conference was held in honour of Professor P.C. Kapur of the Indian Institute of Technology in Kanpur. Professor Kapur was one of the early students of legendary teacher and researcher of mineral beneficiation, Professor Doug Fuerstenau of the Department of Materials Science and Engineering at the University of California at Berkeley. I have attended my fair share of international conferences and this one certainly rated at the top of the list on several counts. With an open-hearted hospitality which one might almost take for granted once you have spent some time in India, the organizers of the Conference looked after every need of their guests, including breakfast and transport to and from the conference centre, wonderful traditional lunches and dinners and outstanding entertainment in the evenings. The papers were generally of a high standard, and debate flowed enthusiastically and freely. Several international guests delivered seminal papers in their fields as discussed below.

Jan 1, 1996

Following closely Marcona Corp.&apos;s announcement of its new Marconaflo process for transporting mineral slurries by ship (see pp. 96-97, Sept. 1969 [ ]), Midland-Ross Corp. (M-R) now heralds its metallized iron pellet process which supplements Oregon Steel Mills1 (Oregon Steel) new Portland, Ore., plant. Harry J. Bolwell, president of M-R describes the company&apos;s M-R Pellet as "the most exciting advance in steelmaking in a decade, one which will profoundly affect the industry." In fact, other knowledgeable industry spokesmen believe that with these developments the mini-steel plant era is now here and that this technical development along with the Marconaflo process will revolutionize iron ore shipments and steelmaking. The M-R president predicts that electric furnaces can account for 20% of the annual U.S. steel production by 1975, compared with 14% at the present time because of these developments.

Jan 12, 1969

By Manuel S. Rivera

Abstract. Instrumentation in concentrators has evolved from a few isolated indicators to compu- terized control within twenty years. This evo- lution has caused a drastic change in the phil- osophy, personnel and equipment used in a pro- gram of servicing and utilization of present day automation.

Jan 1, 1980

By A. V. Tarasov, V. M. Paretsky

"The design is based on the thermal processing of the wastes in· the intensively bubbled melt in the Vanyukov furnace at the relatively high temperatures (1350- 1450 °C), In this case: -the secondary wastes are not formed; - the especially toxic substances at the outlet from the furnace are absent. The technology was tested on a large scale (on semicommersial bases). Technical and economical basis show profitability of recovery complex for processing of hard garbage waste (HGW) using this technology: the period of capital, investments refunding for the, recovery, complex construction with process annual capacity of 240 thousands tons of wastes is 1,5-2,5 years,"

Jan 1, 2000

By A. M. A. Mohamed, F. H. Samuel, S. Alkahtani

"This article was undertaken to investigate the effect of nickel and zirconium additions on the strength of 354 aluminum cast alloy. The cast alloys were given a solutionizing treatment followed by artificial aging at 190 ºC for 2 hr. High temperature tensile tests were conducted at various temperatures from 25ºC to 300ºC. Optical microscopy and scanning electron microscopy were used to study the microstructure of the samples. The results revealed that the intermetallics phases of (Al,Si)3(Zr,Ti), Al3CuNi and Al9NiFe are the main feature in the microstructures of alloys with Zr and Ni additions. The results also indicated that the tensile strength of alloy decreases with an increase in temperature. The combined addition of 0.2 wt% Zr and 0.2 wt% Ni leads to a 30% increase in the tensile properties at 300ºC compared to the base alloy.INTRODUCTIONThe task of improving the mechanical properties in an aluminum alloy at high temperatures should include the knowledge of several factors which are related principally to a decrease in the strength of the metal with increasing temperatures. This behavior is linked to the change or deterioration in the principal metallurgical parameters of the specific cast aluminum alloy during its performance at higher temperatures. Most of applications of Al-Si casting alloys are generally used at temperatures of no more than 230°C (Lee & Chen, 2002). This recommendation is made in view of the fact that, for certain applications such as those required by the automotive industry, these alloys must operate over a wide range of temperatures and stress conditions where temperatures are liable to rise even higher than 230ºC (Robson & Pragnell, 2003).Aluminum-silicon-copper-magnesium alloys such as the 354 alloys show a greater response to heat treatment as a result of the presence of both Mg and Cu. These alloy types display excellent strength and hardness VALUES (although at some sacrifice of ductility and corrosion resistance. These alloys are used for a wide range of applications, such as engine cooling fans, crankcases, high speed rotating parts, structural aerospace components, air compressor pistons, fuel pumps, compressor cases, timing gears, rocker arms, machine parts, and so forth (Cáceres, Svensson, & Taylor, 2003; Rurrxia, Rong-de, Yu-hua, Cherrxi, Xiao-feng, Heng-rong, & H. Zhuang-qi, 2004)."

Jan 1, 2012

By S. P. Kinney

The efficient operation of a blast furnace is primarily dependent upon efficient contact between the descending stream of solid materials and the ascending stream of gas. The United States Bureau of dines is conducting a program of research dealing with the interior of the present-day furnace. The work is being carried oat by.(1) observations on commercial furnaces end (2) experiments in the laboratory. Through the courtesy of the officials of the Illinois Steel Co. it was possible to make a detailed investigation of the interior of the shaft of Number.4 furnace at the company&apos;s South Works, South Chicago, Ill. The experimental work is to be reported in a U. S. Bureau of Mines bulletin which will include the results of several thousand observations on the interior of the shaft of this furnace. Such of the data as are presented later in this paper constitute only a brief summary.

Jan 1, 1929

By Elizabeth Varghese, Sanket Rawat, Prachuryya Kaushik, Ravi Kant Mittal

"Geo5 Software is gaining popularity worldwide due to its expediency in analysis and design of pile foundation. The analysis is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards. Moreover, the ultimate resistance of pile in the software is based CSN 73 1002, Fellenius method, NAVFAC DM 7.2 and Tomlinson method. Due to the specificity in calculation of ultimate resistance, it becomes necessary to validate the results arrived using the software for better accuracy. Furthermore, the above-mentioned methods are not necessarily popular in every design offices. Therefore, an attempt has been made to predict the efficiency of Geo5-v15 software to analyze the pile foundation by comparing it with the results obtained using the analysis based on Indian Standard IS 2911:2010, performed with spreadsheet specifically designed for the same purpose. The accompanying outcome of the comparison and several shortcomings found in the design part associated with the software has been highlighted in the later part of the paper. Besides, the optimization tool present in the software is also described for the more efficient and economic design of pile foundation, hence contributing as practical aid to structural engineers.INTRODUCTIONThe analysis of individual pile foundation and pile in groups can be said to include the three main important parameters – Ultimate bearing capacity, Settlement and Structural Design. The first two parameters are to be evaluated to check the reliability of foundation against ultimate limit state and serviceability limit state. The third parameter includes the analysis of pile against both horizontal and vertical load. This parameter mainly intends to evaluate the size of foundation and the amount of reinforcement. Geo5 is a software which can expediently compute the above mentioned three parameters just by the mere input of the necessary factors. The ultimate bearing capacity analysis in Geo5 is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards depending upon the drained and undrained condition of soil (Bowles, 1968; CSN 73 1002,1987; Felenius,1991; NAVFAC DM 7.2,1984; Tomlinson,1977). However, the method mentioned in IS 2911 (2010) is not the same and have slight variations in way of evaluating the parameters which affect ultimate bearing capacity. Therefore, it becomes necessary to evaluate the efficiency of Geo5 with respect to the value of ultimate bearing capacity and therefore, asserting the confidence in the software based method for the convenience of the designs in Indian Scenario. The present study aims to evaluate the efficiency of Geo5 v-15 software in predicting the ultimate bearing capacity of pile foundation. The results of the software are compared with the bearing capacity calculated using IS 2911 (2010) with the help of excel sheet. Moreover, as the software is frequently put under revision, therefore a comparison of this version has also been made with the latest version of Geo5 (2017) to check whether the latest revision has accounted for the discovered shortcomings. The design steps performed in the software is also shown. As Geo5 make use of IS 456 (2000) for the design purpose, hence it can be considered as reliable with respect to the estimate of the third parameter. Furthermore, the optimization process is also shown in the later part of the paper to emphasize the simplicity of the software in economizing the design cost."

Jan 1, 2017

By Best W. N.

Discussion of the paper of W. N. BEST, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1527 to 1537. WILLIAM A. WILLIAMS, San Francisco, Cal.-I would like to ask whether .Mr. Best ever had any experience with an oil burner that used neither air nor steam? W. N. BEST, New York, N. Y.-Yes. This type is commonly known as the "mechanical spray burner" and uses oil heated under high pressure to above its vaporizing point. These burners are not as efficient as the atomizing type for the following reasons: 1. They produce a round flame which; as with any other type of burner, must pass over a flat surface. A round flame cannot fit a flat surface. 2. They do not evenly distribute the heat, resulting in localized heat. 3. The outlet through which the fuel passes is very small; so all gravities of oil, especially oil containing sand, cannot be burned. 4. Their construction is such that they must be cleaned frequently, as the residuum in the fuel clogs the burner. 5. The oil opening being small, the capacity of each burner is small, so that many burners must be used in a boiler or furnace. (The fewer burners there are, the more accurately they can be regulated.) In marine boilers, these burners are largely used, because they do not require either steam or air for atomization. However, there are other methods by which this objection to other types can be eliminated, such as by the use of a rotary blower and steam turbine engine, the exhaust front the engine passing into the engine condenser, thus obviating loss of water. Mechanical burners are rarely used in shops. I know of but one power plant using them. With mechanical burners, the fuel must be maintained at a high pressure. On board naval vessels, some mechanical burners demand an oil pressure of from 100 to 6001b. It is advisable to reduce the pressure as much as possible, as fractured pipes or fittings are particularly dangerous, for the heated oil escapes as a vapor. In such cases there is liability of an explosion caused by spontaneous combustion.

Jan 12, 1915

By C. J. Brown

Regeneration of hydrochloric acid steel pickle liquors has traditionally been accomplished by pyrohydrolysis. However, a number of factors have recently conspired to reduce the attractiveness of this approach. Moreover, the process is not amenable to small-scale operations. On the other hand, the standard technique for regeneration of sulfuric acid pickle liquors, which is the low-temperature crystallization of ferrous sulfate is applicable to any size operation. A similar technique has recently been developed to regenerate hydrochloric acid. Sulfuric acid is added to the ferrous chloride-bearing spent HCl pickle liquor. The temperature is then reduced to below 0°C, resulting in the crystallization of ferrous sulfate heptahydrate and liberation of free hydrochloric acid. Depending upon the crystallization temperature, variable concentrations of sulfate are left in the regenerated acid. Although this residual sulfate has an impact on the pickling characteristics of the regenerated acid, tests have shown that by adjusting the conditions, pickling rates will be at least equal to those using pure HCI, and an acceptable surface finish will be produced.

Jan 1, 2006

Control dust generated during undercutting in salt mines without causing ore-solubility problems that result from excessive water use. Approach A foam generator was developed to provide a reliable foam to control dust on cutting machines used in mining water-soluble ores. The system was designed to keep total foaming agent/water mixture flowrates below the flow-rates characteristic of water-only systems. The foam generator consists of a reservoir to hold the premixed agent and water, a metering pump, and a small compressor to aerate the mixture. The system is compatible with all cutting machines. How It Works One of the current wet-bar techniques, the through-the-bar trickle system, pumps water through a pipe in the cut-ting bar to its tip placing the water behind the kerf. If the pipe conducted foam effectively the foam would be released in the kerf where it would mix with the cuttings and the dust produced by the chain. For improved foam delivery, however, it is recommended that the pipe be replaced with an external channel welded along the top of the bar. This provides excellent dust control while avoiding the accumulation of copious quantities of foam in the heading. The system is very simple. The foam generator is a 50-gallon tank filled with a mixture of water and foaming agent. The mixture is pumped through a wye fitting to a second line where it is mixed with compressed air, (300

Jan 1, 1984

By C. R. Copeland

Airborne dust emission standards are receiving growing attention. This trend is motivated by significant health studies that have shown adverse health effects due to exposure to dust. Currently, the air quality standards are not specific to particles in the nanoparticulate range (<1,000 nm). However, as our understanding of health related matters increases, it is very likely that nanoparticulate standards will be adopted. It was previously believed that typical comminution and material-handling practices could not result in airborne nanoparticulates. However, experimental studies using air monitoring and SEM have verified the presence of nanoparticulates in the air as a result of comminution and material handling. This means that emerging nanoparticulate air quality standards are a real possibility for industrial operations. With this emerging problem facing the minerals industry, effective suppression methods for nanoparticulates should be explored. Systematic studies have indicated that nanoparticulates from silica can be suppressed utilizing hygroscopic reagents such as calcium chloride. This reagent was as much as 93% more effective than water in suppressing silica nanoparticulates.

Jan 1, 2007

By Frank E. Cash, John A. Johnson

"INTRODUCTION The operators of the Lake Superior district iron-ore mines have made tremendous progress in the past 25 years in the transportation of broken ore from the working places to the surface. This progress has paid divi¬dends in increased production and in lower accident-frequency rates. The trend has been toward more efficient use of mechanical and electrical power and abolishment of many of the backbraking tasks formerly required of min¬ers and trammers.ScopeTransportation of iron ore as described in this paper covers (1) movement from the working place to ore raises by scrapers, shaker,conveyors, and belt conveyors, and, loading underground cars from chutes or-by scraping from loading drifts; (2) underground haulage, which includes underground cars trains, locomotives, and tracks; (3) shaft station's and hoisting shafts, which. Includes dumping cars, storage-pockets; auxiliary storage trenches, and shafts; (4) hoisting, which consists of skips, cages and hoists; and (5) head frames, loading into railroad cars, and stock-pile haulage.The 19 underground iron-ore mines discussed in this paper, situated in the Menominee, Marquette, Gogebic, Guyana, Mesabi, and Vermilion iron ranges of Michigan, Wisconsin, and Minnesota., shipped about 9,000,000 tons of iron ore in 1945, which constituted 56 percent of the underground iron ore taken from the Lake Superior district."

Nov 1, 1947

By E. W. Rouse

THE year 1936 has seen rehabilitation of many plants which had been closed or severely curtailed. The Steptoe smelter of the Nevada Consolidated Copper Co. has been transformed by a rearrangement of the flow of material and utilization of mechanical handling to a maximum. The Phelps Dodge Corp. reports the construction of newer and better reverberatories at the Copper Queen smelter, and of particular interest, a single high-pressure waste-heat boiler placed directly over the uptake. There has also been a complete reconstruction of the smelter at the Laurel Hill plant of the Nichols Copper Co.

Jan 1, 1937

By Ludwig Schmidt

The consumption of gasoline in the United States varies materially with the seasons; during some of the summer months it exceeds the rate of production and in the other seasons the production of gasoline exceeds the consumption, The usual practice of the larger refiners is to store surplus stocks during the winter season in order to meet the heavy demands during the summer months. The following table shows the stocks of gasoline at refineries on the last day of April for the past five years: 1919 593,616,170 gallons 1920 643,5526644 " 1921 747,222,900 " 1922 892,567,766 " 1923 1,336,417.871 "

Jan 1, 1923

By J. M. Karpinski

The need for standard test methods in the minerals beneficiation industry is growing with the increasing complexity of our processes and the more stringent requirements imposed on the quality and uniformity of our products. Although solutions of our problems have never been easy, they will become increasingly difficult to achieve unless we can develop a reliable and reproducible set of test methods. Historically speaking, our need was greatest for methods of chemical analysis. As these methods developed, they improved our ability to determine the grade of ore and measure the effect of our beneficiation attempts. The entire concept of grade and recovery is only as old as chemical analysis. Then came physical measurements. Each new concept in minerals beneficiation was related to certain properties and required corresponding test methods: specific density for jigging, magnetic susceptibility for magnetic separation, and tumbler strength for pellets. And associated with each process was the need for size determination. Size measurement is probably the first physical test ever conceived, and yet we are still improving on it. Dry sieving was quite acceptable for direct-shipping ores, but we had to go to wet sieving to control pelletizing and flotation. Subsieve analyzers have extended our routine measurements to the subsieve sizes, hut not below a few microns. As we all know, the solution of slimes- beneficiation and pollution-abatement problems is hampered by the lack of reliable and reproducible test methods in the fine-particle size range.

Jan 1, 1971

By J. W. Reynolds

Use of crushed waste rock recovered by sink-float separation from normal ore production for backfill is an established procedure at Commco's Sulhvan mme, Kimberley, British Columbia. Need for a safe method of placement in voids which were difficult to reach by gravity methods led to a co-operative venture with Radmark Engineering Ltd. in the development of a workable pneumatic transportation system for rock material. This paper reviews work done to date in a current program, and includes comments on the nature of the fill so placed, options for cementing such fill, implications for other aspects of mining and references to other applications of the system by other organizations who exchanged experiences with the Sullivan mine staff during the five-year period reviewed.

Jan 1, 1972