Search Documents

By L. Kong, V. G. Papangelakis, L. Li

"The Eh-pH diagram of lithium-titanium-water system at 25°C, 100 °C and 200 °C was constructed. It shows that there exist thermodynamic stability areas of Li2TiO3. This indicates a thermodynamic possibility for the formation of Li2TiO3 in aqueous solution. A hydrothermal process has been applied for the preparation of Li2TiO3 using TiCl4 and LiOH•H2O as raw materials. The prepared samples were examined with X-ray diffraction, scanning electron microscopy and thermo-gravimetric analysis and differential scanning calorimetry. The results show that temperature and washing condition have significant effects on the phase composition of the product. Phase-pure Li2TiO3 powders were obtained at 200°C with Li:Ti molar ratio of 2.0.INTRODUCTIONLithium-containing ceramics enriched in 6Li, such as Li2O, LiAlO2, Li4SiO4, Li2ZrO3 and Li2TiO3, are considered as tritium breeding materials (Saito et al., 1998; Roux et al., 1998; Johnson et al., 1998; Hoshino et al., 2002). In view of its admirable properties: low-activation, good thermal stability and thermal conductivity, excellent tritium release performance and reasonable lithium atom density (Kopasz et al., 1994; Roux et al., 1996; Saito et al., 1998; Wu et al., 2008), Li2TiO3 is recognized as one of the most promising candidates of tritium breeding materials. Meanwhile, Li2TiO3, as the precursor of H2TiO3-type lithium absorbent, receives more attention as the development of extracting lithium from salt lakes (Zhong, 2004; Zhang, 2010).Several synthetic techniques have been applied to prepare Li2TiO3 powders, such as solid-state methods (Lulewicz and Roux, 2002; Ramaraghavulu et al., 2011; Mandal et al., 2012), sol-gel processes (Deptula et al., 2002; Lee, 2008) and solution combustion routes (Cruz et al., 2006; Jung et al., 2006; Sinha et al., 2010). A solid-state method may produce a series of problems, including impurity contamination and difficulty in morphology control of the obtained powders, although the process involved is simple. The solgel process is prolonged and usually demands for multi-step reactions, while solution combustion route requires plenty of energy and easily causes product contamination by the fuel used. Owing to its environmentally benign and highly suitable characteristics in fabricating materials, hydrothermal technology has been widely used and became a powerful tool in the field of material synthesis (Yoshimura and Byrappa, 2008). For example, ZnO in the form of bulk single crystals, fine particles and thin films, which is an attractive photoelectric material, was successfully synthesized by hydrothermal process (Sekiguchi et al., 2000; Ohshima et al., 2004). A hydrothermal technique was also used to the preparation of carbon nanotube, which possesses outstanding mechanical, structural and electric properties (Bernholc et al., 1997), and is superior to the commonly used method (Gogotsi and Libera, 2000). There, it provides an option for preparing Li2TiO3. Laumann et al. (Laumann et al., 2010) synthesized cubic a-Li2TiO3 by hydrothermal reaction at 180 °C for 18 h, using TiO2 powder, comprising of anatase and rutile, and lithium hydroxide in de-ionized water. However, the prepared a-Li2TiO3 is extremely unstable with a maximum lithium loss of 75% when treated in bathing experiment."

Jan 1, 2012

By A. H. Mumin, A. Prikhodko

"This paper provides an understanding of interpreting and evaluating airborne time domain electromagnetic (TEM) surveys as applied to massive sulfide exploration. Variations in the conductive morphologies of massive sulfide ore systems are discussed, followed by forward modelling exercises examining the derived TEM response to these morphologies and discussion of the subtleties of data interpretation. Deposit morphology in the orientation at formation and the variations occurring due to later deformation are considered. Images of corresponding resistivity–depth models are provided. The combined modelling results provide a low-cost method for initial interpretation and screening of TEM anomalies. RÉSUMÉ Cet article nous permet de mieux comprendre l’interprétation et l’évaluation des levés élec-tromagnétiques aéroportés en domaine temporel (TDEM, de l’anglais time-domain electromagnetic) appliqués à l’exploration du sulfure massif. Y sont débattues les variations au niveau des morphologies conductrices des systèmes de minéralisation du sulfure massif, suivies d’exercices de modélisation prospective qui examinent la réponse dérivée des TDEM à ces morphologies et d’une discussion sur les subtilités de l’interprétation des données. L’étude envisage la morphologie de l’orientation originelle non déformée des gisements ainsi que les variations résultant d’une déformation ultérieure. Des images des modèles correspondants de résistivité-profondeur sont fournies. Les résultats combinés relatifs à la modélisation proposent une méthode peu onéreuse d’interprétation et de contrôle initiaux des anomalies dans les TDEM.INTRODUCTION Electromagnetic geophysical surveys are an indispensable foundation of many mineral exploration programs and can account for as much as half of the predrilling exploration costs. Quantitative mass interpretation of the survey results remains difficult due to the infinite variation of deposit morphologies, their complex physical properties, and the presence of barren conductive materials that can mimic or mask the response of targeted ore. Many modern geophysical investigations that focus on time domain electromagnetic (TEM) data interpretations are devoted to problems with inversion and modelling and their algorithms. Although a few of these investigations have resulted in commercial software products, these require highly qualified and experienced users and usually include geometric assumptions. Furthermore, without the input of known physical properties and geometric constraints, the inversion results are highly ambiguous. A number of case studies document the geophysical responses to known targets in well-defined and diverse geo-electrical environments, providing a high degree of correlation between field obser-vation and the results of the modelling used in this style of investigation (Hone, 1980; Schneider & Emerson, 1980; Tyne, Idnurm, & Malone, 1981; Bishop & Lewis, 1992; Hopgood & Hungerford, 1994; Meju, 2002; Yang & Oldenburg, 2016). The uniqueness of the target/environment parameters and their specific features limits the use logy is poorly understood. The responses are therefore that are devoid of complicating environmental factors (e.g., highly conductive overburden and hostrocks or nonuniform target conductivity) as a first approach to the interpretation process of such case studies as the main reference for interpreting TEM survey responses in areas where the underlying geomodelled from generalized and typical geological models"

Jan 1, 2018

By H. K. Lin, J. L. Oleson

The purpose of this study is to develop a mathematical model to describe the oxidation of cyanide with SO2as proposed in the Inco process. This research employed a direct method for measuring the change in cyanide concentration with respect to time as effected by varying concentrations of SO2, copper and pH. Developing this model may be applicable in determining optimum conditions in a process well known and used in the mining industry. It was determined that the reaction is first-order with respect to cyanide, SO2and [Cu+2].The reaction order is 0.15, or zeroth order with respect to [H+] at pH range from 8.0 to 9.5.The activation energy, Ea, is 21.6 kJ/mol. The overall rate equation, as determined through this study is: [ ]

Jan 1, 2004

By Edwin S. Secor

The Federal Bureau of Mines conducted a field survey of 153 bituminous coal strip and auger mines to estimate coal recovery from surface mines in the Eastern United States. Recovery was calculated from field data by measuring coal losses resulting from mining coal and leaving barriers. Mean total recovery for strip mining in States east of the Mississippi River was 83.0 percent and ranged from 72.3 percent for Tennessee to 91.3 percent for Maryland. Mining losses and barrier losses were 10.1 and 7.7 percent, with standard deviations of 4.8 and 10.4 percent, respectively, indicating that barrier losses, although less than mining losses, were more variable. Mean total coal recovery varied only slightly for the two regions studied; 82.7 percent for Appalachia and 84.3 for the Midwest. Total recovery grouped by mining method--contour, area, and mountaintop removal--was 79.8,84.7, and 85.3 percent, respectively. Mean auger recovery was 35.9 percent; of the total average loss of 64.1 percent, over one-half resulted from design limitations while the remainder was attributed to operating losses. The wide recovery range at individual mines indicates the variability of the eastern surface coal mining industry. Because of this, care should be exercised in applying the results of this report to reserve estimates other than those of a general nature.

Jan 1, 1977

By E. B. Kester

Of the many angles from which coal can be studied it is evident that some have a direct and others have only an indirect bearing on its physical or chemical nature . The more drastic the treatment employed in an investigation , the more inferential become the conclusions permissible from the experimental evidence obtained . Thus , ultimate and proximate analyses tell something concerning age , behavior on carbonization , and possible industrial usefulness , but nothing regarding structure or composition in the larger sense . Strong oxidation reveals the fact that benzenoid , pyrrol , and furane rings are prevalent in the chemical substances present , and milder oxidation indicates that the mass of coal , as in the case of the peats and lignites , is humic in character . But beyond such points of information , very little additional can be gained by the use of these more or less vigorous measures . To gain wider knowledge of the actual constituents of coal substance as found investigators have worked out systems of separation by means of solvents , of which a large number have been employed at various times both singly and in combination . The list of solvents includes petroleum ether , benzene , toluene , xylene , ethyl ether , alcohol , acetone , carbon bisulphide , pyridine , quinoline , aniline , phenol , tetralin , glycol ethyl ether glycol ethylether acetate , glycol methyl ether , glycol diethyl ether , pine oil , mesityl oxide furfural , benzaldehyde , ethylene oxide , rosin , caustic potash in solvents , amyl alcohol plus pyridine , chloroform , carbon tetrachloride , acetylene tetrachloride , naphthalene , and others . Once a coal has been extracted it has become common practice to subdivide the extract by means of partial solution in other and weaker solvents . Thus , we find the oily and solid bitumens of Fischer ( 1 ) , 3 Bone ( 2 ) and others ; the alpha , beta and gamma constituents of Wheeler ( 3 ) ; the classification of Novak and Hubacek ( 4 ) embracing oils , resins A , resins B , bitumens An , bitumens Bn , and bitumens Cn ; Crussard's ( 5 ) malthenes , asphaltenes , and carbenes , borrowed from asphalt terminology; and the 40 or more subdivisions of the phenol extract of coal worked out by Frazer and Hoffman ( 6 ) . Perhaps the primary object of interest in these many researches has been to find the coking principle of coal , and to study it and to learn why certain coals form hard , wellfused cokes , and others merely fall to pieces during carbonization . The origin of the various constituents of the gas and tar , the temperature at which each forms , and something of the mechanism of their synthesis have also been sought , as well as new bases for adjudging rank .

May 1, 1931

By G. Ozbayoglu, Z. Ozdemir

Turkey is the main boron minerals producing country in the world. The most important boron minerals are tincal, colemanite and ulexite. All mining, beneficiation and handling operations generate fines which cause ecological and economical problems. Utilization of this accumulated material requires both upgrading and agglomeration. The aim of this research was to exploit the ulexite fines by improving their grade and size. Attrition-scrubbing followed by washing and screening was employed for upgrading the fines. It was found that the grade can be increased from 23-25% B2O3 to 29% B2O3 with 73% recovery. Briquetting was applied as the size enlargement process. During the briquetting, the effect of moisture content, pressure, amount and type of binder, and drying on the quality of briquettes were investigated. The tests showed the possibility of production of strong briquettes by adding water alone, but the briquettes had no resistance to abrasion and water. Binders, namely boric acid and borax have been added to improve the properties of briquettes. The results showed that the compressive strengths and abrasive resistances of briquettes obtained with both binders were acceptable. However, the briquettes have no water resistance properties.

Jan 1, 2004

By Andy Judge

"In traditional Permanent Magnet Machines, such as electric motors and generators, power is transmitted by magnetic flux passing through an air gap, which has a very low magnetic permeability, limiting performance. However, reducing the air gap through traditional means carries risks in manufacturing, with tight tolerances and associated costs, and reliability, with thermal and dynamic effects requiring adequate clearance. Using a magnetically permeable, high thermal conductivity material has the potential to improve magnetic performance, while at the same time offering performance advantages in heat transfer.Ferrofluids can be used to improve permeability in the rotor I stator gap. However, there are several tradeoffs in this approach. Fluid immersion comes with an increase in fluid friction loss compared to the windage losses of a traditional system. Isolating the rotating components from the ferrofluid can offset this effect. Also, while the magnetic effect can be positive for gap permeability, leakage flux can increase, and saturation can limit gains. These effects must be taken into account for a system optimized for ferrofluid immersion.IntroductionPermanent Magnet Machines (PMM's) convert electrical energy to mechanical energy in motor applications, or, for generator applications, convert mechanical energy to electrical energy through means of passing alternately polarized magnets past electrical coils. Looking at a simplified version of a PMM, where Rx is magnetic reluctance and <l>x is magnetic flux, we have the circuit shown in Figure 1."

Jan 1, 2013

By Lj. D. Andric

By the micronization-milling of the material, the size and the structure of its particles are changed and it comes to the increasing of the potential energy of the system as well as to the chem-ical activity of the material what is the result of an increased free surface and of the concentration of the grate defects, that is of the internal energy of the system. All these changes that are reached, show that new characteristics of treated materials are got by micronization process. Controlling the process of the micronization and by purpose directing of the new characteristics of the activated materials, we can have the positive effects and use them in more technologies. Talc is important nonmetallic mineral raw material that is widely used as either the basic raw material, or as filler. This has stimulated its technological investigation, as well as the investigation of its physical-chemical characteristics. In this paper are shown experimentally reached results of the physical-chemical characteristics of the talc during the process of the micronization in high energetic mill. In this paper, the optimum conditions of miconization of talc in high-energy-speed rotary mill and its influence micronization on a degree of Fe2O3recovery by hydrometallurgical methodes, are presented. The X-ray analysis of the obtained products showed that high quality talc with low content of can be obtained by these physical-chemical processes In this paper, the principles and application or fine and ultra-fine grinding high-energy attriton mill with small balls, enabling fast, efficient grinding, low energy consumption, short grinding time and easy handling will be described.

Jan 1, 2014

By Frederick H. Raab

The electromagnetic retransmission system is a new, automated method of locating trapped mine workers. This technique overcomes many 1 imitations inherent in electromagnetic direction finding by reducing the effects of the conducting ground to an acceptable maximum, by finding position accurately in the presence of antenna tilt, and by eliminating the need for the receiver to be located directly above the subsurface transmitter. Three transportable three-axis magnetic-dipole transmitters on the surface create a system of electronic grids in which the phases of the downlink Signals convey position information. The subsurface retransmitter modulates the uplink carrier of the existing beacon transmitter with the received downlink signal; the coal-pillar loop antenna is used for both receiving and transmitting. The uplink receiver uses a three-axis antenna and extensive digital signal processing. A small computer integrates data, estimates position, and controls system operation through VHF-FM communications. Both coal-mine and deep-mine operation are possible by selecting appropriate transmitting power and signal frequencies. This report shows such systems to be both feasible and practical.

Jan 1, 1980

By E. Keskinkilic

"Electrical steels are used in motors, power generators, and transformers for electrical applications owing to their superior magnetic properties. These properties are attributed to the presence of a significant amount of silicon in the steel composition. Silicon steels are mainly grouped into two categories: grain-oriented (GO) and non-grain-oriented (NGO). The Si content of silicon steels is generally between about 0.50% and 6.5%. Therefore, silicon steels are further classified as low-, medium-, and high- Si steels. In this paper, liquid steel processing practices for certain silicon steel grades are outlined by considering a steelmaking company that integrates a basic oxygen furnace (BOF), a ladle furnace (LF), and an RHtype degassing unit (RH). Possible problems are identified, suggestions are discussed, and conclusions are drawn on the basis of real plant data. IntroductionSilicon steels are widely used in motors, power generators, and transformers for electrical applications owing to their superior magnetic properties. They are mainly grouped into grain-oriented (GO) and non-grain-oriented (NGO) silicon steel grades. However, the differences in the properties and thermomechanical production of GO and NGO grades are outside the scope of this paper. In this study, liquid steel processing of certain silicon steels will be discussed. In the integrated iron and steelmaking process, converters are the primary steelmaking units that are used mainly for decarburization and removal of phosphorus, and for obtaining liquid steel with a specific chemical composition and suitable temperature for secondary steelmaking operations. Ladle furnaces are a type of ladle metallurgy station consisting of electrical and/or chemical heating facilities for adjusting the liquid steel temperature during alloying. Various types of vacuum units are used for decarburization and removal of nitrogen, hydrogen, and sulphur, depending on the metallurgical conditions of the vacuum units. In this study, an actual steel-production company is considered in which the primary steelmaking operation uses a basic oxygen furnace (BOF) converter with N2/Ar bottom blowing, and the secondary steelmaking operations involve (1) a ladle furnace (LF) heated by three graphite electrodes and equipped with Ar and N2 top/bottom mixing facilities, and (2) an RHtype (circulation) vacuum degassing unit equipped with a top-blowing attachment for oxygen blowing and an Ar-purging system from an up-leg snorkel."

Jan 1, 2018

By C. O. Hawk

As an exploratory effort to produce useful products from coal by a new path, the Bureau has made a few experiments on the fast heating of finely ground coal particles by irradiation with a flash of high intensity light. The flash was produced by an electrical discharge at high voltage through a xenon-filled tube. The flashes lasted from 2 to 3 milliseconds. The reaction took place in small sample tubes, ½ inch-dimeter by 4 inches long, and with small amounts of coal (total amount charged 0.1 gram, probable effective amount not more than 20 milligrams). Average particle size of the coal, estimated on a numerical basis, was 20 microns. Temperatures reached were evidently quite high, because all products obtained in quantity were characteristic of high temperature pyrolysis. Apparently, conversion of the coal was extensive where isolated particles received the full benefit of a flash. It seems particularly significant that acetylene was present in appreciable amounts--comprising almost 3 percent of the total gaseous product in one case. This is good evidence of a short heating period to very high temperature (well above 1,000° C) followed by rapid quenching. Although the results are interesting, they do not suggest any immediate practical application.

Jan 1, 1963

By A. G. Lylie

Introduction At the Britannia Mining and Smelting Company&apos;s mill, the equivalent of 2,500 to 2,800 pounds of copper sulphate crystals per day is made from copper which is precipitated from the mine-water. This copper sulphate is used in the mill for the recovery of sphalerite by2 flotation. From 1932 until 1936 it was produced by exposing the precipitate to air for thirty days and then dissolving the oxidized copper with dilute sulphuric acid. In 1936, the flotation of sphalerite was discontinued and, when it was resumed in 1947, steps were taken to try to improve the former method. The present paper outlines the way in which this was done, and describes the plant and procedure by which copper sulphate is now being made, and by means of which an appreciable saving is being effected. Aboratory Tests The previous work had established that the precipitate, which consists mainly of metallic copper, must be oxidized before the copper would dissolve in dilute sulphuric acid. Various methods for oxidizing it were tried but in the early laboratory work the only suitable one found was to heat the precipitate to 600°C. and hold it at this temperature for two hours. When this was done, approximately 90 per cent of the copper became soluble in .acid. This percentage was considered satisfactory for practical purposes, but the cost of roasting was prohibitive because only a small amount of roasted precipitate was required each day.

Jan 1, 1951

By Snowden D. V, Standing C. A, Ryba A, Bywater A

McKinnons open pit gold mine, located within the Cobar Basin in New South Wales, is characterised by complex mineralisation controlled by the intersection of steep faults in the hinge zone of an anticline. Resource estimation using indicator variography and indicator kriging was based on RC drilling on 25 in sections together with grade control RC drilling on 12 in by 12 in and 6 m by 6 in patterns. Rigorous sampling and checking procedures were used to verify the reliability of the drill hole data. Blast hole data was used to assist grade control in defining ore block boundaries.

Jan 1, 1997

A recently developed technique for use in collieries is described in which samples of gas of relatively high vitiation value are obtained from points deep within a developing goaf by means of pipes. This technique prevents dilution of small quantities of carbon monoxide by large quantities of fresh ventilation air and eliminates interference from shotfiring gases. By using the technique it should be possible to assign a characteristic ratio of carbon monoxide to oxygen consumed to any district and to predict the onset of heatings.INTRODUCTIONGas analysis has played a vital role in detecting heatings in collieries all over the world. By analysing return air from a district and by calculating the percentage ratio of volume of carbon monoxide found to oxygen consumed (known simply as the &quot;carbon monoxide ratio&quot;) it has been found possible, in many cases, to assign a characteristic ratio to a district under consideration. This characteristic ratio serves as an index of the spontan~ous combustion tendency of a goaf area. Any definite and consistent increase in the ratioabove the normal figure&#183; indicates that a heating is developing and hence adequate preparations may be made to deal with the trouble.This ratio technique was developed by Graham (1920-21) who found (Table 1) that the temperature of oxidizing coal was directly related to the ratio obtained from analyses of the effluent gas.Until recently, most attempts to employ a similar technique in collieries working the Greta Seam (N.S.W.) were not successful. From experience gained over the past few...

Jan 1, 1961

By K. Holmberg, D. Herriot

This paper by Mr Mclvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulat¬ing load operation. The Bond calculation is itself based upon

Jan 1, 1989

By ALBERT LONG, Wing G. Agnew, FELIX CHAYES, Alton Gabriel, Leonard Obert

Although the technique of diamond drilling was developed nearly 80 years ago, the use of this process as an aid to mining and other fields of engineering has increased greatly during the last decade , primarily as a result of the development of the cast -set bit , which now largely replaces the hand - set types , and of the use of bort instead of carbons . Since this transition to cast - set bits and bort diamond , many papers ( 1-14 ) have been written on the application of diamond drilling to various engineering problems . These papers contain , besides specification of the problems , some information on the labor and bit costs and a few data on drilling technique . These data , however , are subject to restricted interpretation owing to the large number of variables , which are not controlled in field drilling . Only one paper has come to the attention of the authors , namely , that by Sundberg and Lindqvist ( 16) , which reported a study of diamond drilling under controlled conditions . This paper was written early in the transition period, and the data and conclusions presented therein have had , without a doubt, considerable influence on the development of presentday diamond bits and In view of the fact that during the last 10 years thrilling procedure . have been new developments in diamond bits. and new applications of diamond drilling , a general program of research has been inaugurated to study the problems resulting from these changes .

Mar 1, 1947

By M. D. Riegel, P. B. Pizzimenti, E. M. Zamiskie, Britain A. Materek

"The Skanska/Kiewit/ECCO III team (SKE) in association with HNTB was awarded the design-build contract for Phase I of the Kosciuszko Bridge Replacement Project. As lead designer for the SKE team, HNTB was responsible for the design of the Brooklyn Connector which includes construction of approximately 2000 feet of new staged earth-filled embankments utilizing prefabricated modular retaining walls (T-Walls®). The proposed embankments will be constructed adjacent to and beneath the existing Brooklyn Queens Expressway (BQE) viaduct while the existing viaduct remains in service. Critical aspects of the settlement assessment relating to the soils supporting the existing BQE will be addressed, as their behavior drives the deformation of the viaduct. Furthermore, a construction monitoring program was used to enable the designer to assess settlement predictions and allow SKE to mitigate potential impacts to the existing BQE during construction. Additionally, the methodology for installation of the embankments in a limited access area underneath an active viaduct supported on settlement sensitive shallow foundations will be presented.INTRODUCTIONSkanska-Kiewit-ECCO III Joint Venture, in association with HNTB was contracted by the New York State Department of Transportation (NYSDOT) to design and construct the Phase 1 replacement of the Kosciuszko Bridge Design-Build Project. Phase 1 of the project involves the design and construction of the new eastbound structures of Interstate 278 over Newtown Creek from Brooklyn to Queens. The project runs between Morgan Avenue in Brooklyn and the Long Island Expressway Interchange in Queens (approx. 1.1 miles) and includes the staged demolition of the existing structures."

Jan 1, 2016

By R. H. Lien

The Bureau of Mines investigated a roast-leach process for recovering a marketable lithium product from a montmorillonite-type clay deposit located on the Nevada-Oregon border. The clay sample treated in the investigation contained 0.6 wt pct Li. The lithium recovery process consisted of several unit operations. The lithium silicate compounds in the clay were converted to Li2SO4 by roasting a pelletized mixture of clay, limestone, and gypsum at 900° C in a direct-gas-fired rotary roaster. Water--leaching the calcine at 40 pct solids extracted the Li2SO4. Lithium recovery from the leach solution involved concentrating the solution by evaporation, adding Na2CO3 to the concentrated solution to precipitate Li2CO3 , and filtering the slurry to obtain the product. The product filtrate was recycled to the evaporator following a crystallization step. About 80 pct of the lithium in the clay was recovered as 99-pct-pure Li2CO3. Process operating costs were estimated at $2.12/lb Li2CO3 produced; the current Li2CO3 selling price is $1.48/lb. Raw materials. accounted for 30 pct of the total operating cost.

Jan 1, 1985

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"At the moment climatic conditions are a primary problem of the exploitation of copper ore. The efficiency of preventive actions in order to improve climatic conditions is connected with the knowledge of changing air in underground excavations. This article demonstrates the analysis of types of ventilation dams which are used in sealing abandoned areas on the maintenance of climatic working conditions in excavations has been conducted at the exploitation in Polish copper ore mines. INTRODUCTION The basis for mining activity performed by KGHM Polska Miedz S.A. is mining copper ores from the deposit lying at depths between 600 and 1,200 m below ground level. Activity has continued since 1963. The copper ore deposit is mined in ‘Lubin’, ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines, where difficult climatic conditions occur. The major factor moulding the climatic conditions in headings is the original temperature of rocks, being the result of geological conditions of the lying of the deposit and the existing geothermal degree. In the faces of present opening-out and preparatory headings, driven from mining areas of ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines in order to open out deeper parts of the deposit, the original temperature of rocks reaches 45°C. Excluding the original temperature of rocks, the following are additional factors affecting the deterioration in the climatic conditions: • thermal properties of deposit rocks, • employed room-and-pillar mining systems, which are characterised by a large surface of exposure of rocks, • using self-propelled mining machines with diesel drive, • a high concentration of mining works, • setting up high-power electrical equipment in headings, • complex structures of mine ventilation networks, • a limited number of ventilating shafts, • constantly longer air-transport routes, • a significant accumulation of water increasing the humidity of supplied air. According to the valid Polish provisions (§21, 2013), the primary criterion of assessment of a climatic hazard is the occurrence at a workstation in an underground mining heading of an equivalent climate temperature of more than 26°C, which temperature is determined according to the following dependence:"

Jan 1, 2019

By John A. Johnson

Conclusions regarding the use or omission of stemming in blasting have not peen reached, pending completion of all aspects of this investigation. The results from the dust phase of this study on six classes of stemming prove that the kind of stemming affects the amount of dust produced from blasting. In previous work at the Mount Weather testing adit it was demonstrated that blasting produces the highest dust concentrations of any of the mining processes.5/ Under the conditions prevailing at the Mount Weather testing adit, the average of all rounds having a break of at least 95 percent showed that the least amount of dust was produced when no stemming was used.

Jan 1, 1940