Search Documents

By Mitsuru Tanahashi

In order to develop an effective process for the production of from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at a solar-grade silicon (SOG-Si) 1773K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten M6-8 followed by oxygen gas injection into the melt (Two-stage connecting process). II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection Process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

THE following notes simply sum up the writer's experience, which extended over a very busy period of some three years, dealing with wolfram ores and concentrates. The three methods for the estimation of tungsten that are discussed below are well known, but these results of their trials and comparison under technical conditions may be interesting. Method I. The routine procedure for the assay of rich wolfram ores or concentrates was as follows: Take 1 gram of finely-ground sample; digest with HCl and HNOs for about 2 hours, evaporating down to near dryness. To the remaining 5 cc., say, of liquid, add water, warm or boil for 1 to 1.5 hour, filter through a small filter paper, and wash the beaker and the insoluble matter with hot dilute HCl. It is best to keep the bulk of the insoluble matter (WOs, Si02, etc.) in the beaker at this stage. Then plaee a weighed porcelain dish under the filter funnel and wash the beaker and the filter paper with successive small quantities of strong NHOH, finally bringing all the insoluble matter on to the filter paper, and collecting the ammoniacal filtrates in the porcelain dish (S). Then place the filter paper with the insoluble matter in a porcelain crucible, dry and burn off the paper, cool, and brush the contents of the crucible on to an agate mortar, grind it to flour, and brush this back to the original beaker without loss. In the absence of draughts this can be done safely. Re-treat this residue with' acid and ammonia as above, running the second ammoniacal filtrate into the previous porcelain dish, which in the meantime has been heating on a water-bath.Finally evaporate to dryness on the water-bath the combined ammoniaeal filtrate, and then heat gradually to a red heat over a Bunsen burner, cool, and weigh. Then the contents of the porcelain dish give the WOs (tungstie aeid) direcvly (5).The final filter paper and insoluble matter may be ignited in a porcelain crucible, thus giving the "insoluble matter." If the ore...

Jan 1, 1922

By K. H. Johnston

This guide was written to furnish the coal industry with a description of techniques, instruments, and clues on how to find abandoned oil and gas wells that have penetrated coal seams. The report includes specific information on searching techniques currently in use by several coal mining companies, gas-transmission companies, and waterflood operators, as well as information on State agencies responsible for the enforcement of laws and the preservation and distribution of data pertaining to the drilling, development, and abandonment of oil and gas wells. Comparative tests were performed with several commercial electronic metal detectors to determine the feasibility of using them to aid in the search for abandoned wells and to determine the instrument most suited for that particular use. The role of methane detectors to locate abandoned wells is described, including a case history. Tests were made to develop an efficient procedure to follow in systematically searching an area for metallic clues or hydrocarbon evidence to abandoned wells. The guide describes, in detail, a search sequence, including the collection of basic data, preparation of the selected area, and the physical search. Methods are given for evaluating the results.

Jan 1, 1973

By Donald E. Ralston, V. Rajaram, Michael N. Greeley, John W. Peters, Terry J. Laverty, F. S. Kendorski, Peter G. Chamberlain, J. Brent Hiskey, William C. Larson

Preliminary figures from the US Mine Safety and Health Administration show 801 underground metal mines and 490 surface metal mines, at the end of 1981, up from 663 and 383, respectively, in 1980. Preliminary MASH figures also show 207 underground nonmetal mines and 1070 surface nonmetal mines at the end of 1981, compared with 167 and 1092, respectively, last year. In addition, preliminary MASH figures show there were 14,676 mineral extraction operations on the surface and 3845 underground at the end of 1981, versus 14,951 and 3675, respectively, for last year. The number of mines, then, in three of four categories increased significantly, while having a lower net total of just 2% in the other category. And the number of underground extraction operations increased nearly 5% for the year, while surface operations were down less than 2%. But despite operations totals that mostly held their own or showed significant increases, it was a tough year for the nation's mining industry. The nonferrous segment of the industry had a bad year and 1982 may be no better, according to Business Week (Jan. 11, 1982), which adds that a turnaround is impossible unless the general economy recovers. Even then, with diminishing markets and overcapacity plaguing its products, the mining industry's condition "will be far from robust," the magazine says. The basic problem is that nonferrous metals-aluminum, copper, lead, molybdenum, nickel, and zinc-are tied to the most troubled sectors of the US economy. As recently as 1979, for example, more than 40% of all aluminum shipments went to the construction and transportation industries. Last year, these markets were down to 35% of aluminum shipments. And molybdenum sales to steel producers dropped by nearly 15% last year. Moreover, nonferrous products ended 1981 at disastrously low prices. Molybdenum oxide sold at $8.77/kg ($3.98/lb), half its $17.63/kg ($8/lb) price earlier in 1981 and aluminum was listed at $1.08/kg ($0.49/lb), compared with $1.54/kg ($0.70/lb) a year earlier. The Comex price of copper was $1.54/ kg ($0.70/lb), down from $3.11/kg ($1.41/lb) in early 1980, in real terms the worst copper price in 30 years. Lower prices led operators to cut their output and increase layoffs, shut down mines, and defer capital spending projects. In December, Duval Corp., a Pennzoil Co. subsidiary, shut all four of its US copper mines until March. Aluminum Co. of America had laid off 7.3% of its work force, shut nine of its 38 smelting lines, and entered 1982 operating at only 68% of capacity. Inco Ltd., the Free World's largest nickel producer, lost money in 1981, an estimated $11 million, for the first time since 1932. And, like Falconbridge Nickel Mines and other major nickel producers, had cut back on nickel production and was operating at only 63% of capacity (Forbes, Feb. 15, 1982). Amax, the country's largest molybdenum producer, had cut production by 20%. And Hanna Mining Co. sold lead for $5.07/kg ($2.30/lb), about $1.54/kg ($0.70/lb) below what it cost to produce. Another problem is that copper companies in the next few years must come to terms with problems of aging smelters. Some companies are simply closing them. In 1980, Anaconda closed its 75-year-old Butte, MT, smelter and is shipping concentrates to Japan, rather than modifying the smelter to meet environmental requirements. And oth Phelps Dodge Corp. and Asarco Inc. have antiquated smelters on which they will have to make decisions. The most troubled metal in 1982, Business Week said, will be molybdenum, with no real recovery in sight until the mid-1980s. High molybdenum prices in the late 1970s, caused in part by shortages, triggered overexpansion that will take years for the US market to soak up. On a more upbeat note, 1981 mergers might help stabilize the industry by providing funds for mining companies. Standard Oil Co. (Ohio) said it plans to spend $7 billion on Kennecott during the next 10 years for modernization and expansion. And Atlantic Richfield Co. said it will spend $500 million on Anaconda Copper Co. during the next five years. Another positive note was sounded by T. H. Adams of the United Banks of Colorado Inc. He said he expects the mining industry to experience moderate growth in 1982, led by "interest rate sensitive" demand from energy, electronics, and defense markets. And mining will be helped by "weak, but improved" construction and auto markets. The mining industry will be operating in an economy stronger than 1981, but still relatively sluggish by postwar standards, Adams predicted. Iron Ore Estimated US iron ore production in 1981 was 75.2 Mt (74 million long tons), up 6% from 70.7 Mt (69.6 million long tons) in 1980, though down from the 87.1 Mt (85.7 million long tons) produced in 1979. The mine value of usable iron produced from domestic mines was estimated at $3 billion. US iron ore was produced by 28 companies operating 35 mines, 26 concentration plants, and 16 pelletizing plants. The mines included 34 open pits and one underground mine. Byproduct ore recovered from copper- and titanium-mining operations accounted for less than 1% of total iron ore production. Fifteen mines operated by nine companies accounted for 94% of total

Jan 5, 1982

By L. E. Murr, P. J. Smith

A study has been made by transmission electron microscopy of thin foils of 304 stainless steel fatigued external to the electron microscope in reversed bending, and of thin foils fatigued directly within the microscope in alternating tension. The build-up of stacking faults in the thin foils during fatigue zoas correlated with the dislocatirm structures found in thin films prepared fror fatigued bulk specimens. The performance of the special devices designed for fatigue of thin foils so outlined and the importance of alternative methods of preparation of more uniform fatigue specimens bY vapor deposition are emphasized. INVESTIGATIONS on fatigued bulk aluminum1,' and stainless stee13j4 have revealed the existence of dislocation substructure on examination by transmission electron microscopy of electrolytically thinned foils representative of these bulk specimens. While this technique has proved extremely valuable, it has several shortcomings. First, the method of fatiguing bulk specimens and then thinning to foil for electron-transmission observation allows only one observation of internal structure at any one portion of the fatigue life. Second, thinning the bulk fatigued specimens to foil results in the loss of at least one original surface. Thus, what one sees in the remaining electron-transparent sections is an internal dislocation or fault structure which in many cases cannot be correlated with the original surface markings. This is an undesirable feature, since it is well-known that metal surfaces play an important part in the fatigue process.5 An obvious third undesirable feature of the thinning-from-bulk technique is the fact that static observations have difficulty (in the case of fatigue) explaining the mechanism of a dynamic process. What is required then is a method whereby a selected thin area can be continuously observed either while undergoing cyclic deformation or at various fixed stages of fatigue deformation. While Murr and wilkov6 have reported some success with an apparatus designed to fatigue thin metal foils directly within the electron microscope, the nature of the specimen-mounting procedure and the mechanical features involved in the adaptation of the fatigue device to the electron microscope make this method difficult to operate. It was not possible, for example, to make frequent observations of a selected area because of difficulty in maintaining a chosen area in a stable viewing position inside the electron microscope. Except for the build-up of a dislocation substructure and what are commonly referred to as "slip striations", little else has been reported from observations on thin-foil sections prepared from bulk fatigue specimens. segal17 has found "slip striations" in stainless-steel fatigued specimens which were electropolished from both sides, but gave no explanation as to their origin or identity in terms of lattice imperfections. The research to be reported in this paper was undertaken with the following objectives in mind. First, an attempt was made to devise a technique or techniques whereby thin metal foils could be fatigued and repeatedly observed by transmission electron microscopy. Second, it was hoped that some correlation could be made between deformation striations found in fatigued thin transmission specimens and thin foils prepared from bulk fatigued specimens. These investigations illustrate quite convincingly that a feasible method is available for the direct study of the fatigue mechanism and similar dynamic phenomena in thin transmission specimens inside the electron microscope. I) EXPERIMENTAL METHODS Three modes of specimen fatigue and observation of fatigue damage were used. These involved fatigue of thin-foil specimens in a special arrangement external to the electron microscope and observation of a selected area at various stages in the fatigue life, the fatigue of thin-foil transmission specimens inside the electron microscope, and the fatigue of bulk specimens external to the electron microscope followed by thin-foil preparation for direct observation at predetermined stages. Design of the External Fatigue Clip and Specimen Holder for the Hitachi H.U.11 Electron Micro-scope. The purpose of the fatigue clip was to provide a reversed bending fatigue stress to a thin-foil transmission specimen outside the electron microscope. In order to accomplish this, a flat-bottomed, U-shaped brass clip was made as shown

Jan 1, 1965

By Ron Board

"Probably the only thing that can he said about conveyor belt scales without fear of contradiction is that they have been responsible for as much or more puzzlement, argument and frustration than almost any other piece of equipment commonly found in ore processing facilities. To be sure, there are certainly a good number of satisfactory installations, some of these having been achieved through forethought and careful consideration in the early stages of plant design, while others seem to owl their success to what seems to be little more than good luck or white witchcraft; and it might also appear that black witchcraft or other gremlins are solely responsible for the poor performance of many belt scales that enjoy well-designed installations with apparently good operating conditions.This paper is intended to acquaint users with the major operational reasons why belt scales seem so fickle (and downright ornery too), and establish some reasonably simple test standards against which the performance of scale hardware can be measured. Then it shall be shown how the design flexibility of electronic scale systems can offer particular advantages in overcoming some of these everyday problems in a practical way, and without undue inconvenience to plant operations."

Jan 1, 1975

The development of an onboard contaminant diagnostic monitor to continuously measure contaminant level in a mining machine was advanced to a prototype stage in this contract. Several concepts were investigated and it was found that a static spool type sensor was the most reliable and accurate. Laboratory and field tests showed that an instrument based on this concept is capable of measuring contaminant levels and/or size distribution, depending on the configuration of the sensor. Moreover, this instrument can function on emulsions or homogeneous fluids. Current laboratory equipment can operate on homogeneous fluids only.

Jan 1, 1983

By C. Patrick

Project scheduling is a deterministic technique utilizing single estimates of activity durations. In reality, activity durations are stochastic and can be better represented by probability distributions. This paper describes the development and utilization of a project scheduling simulation which combines analytical scheduling with stochastic activity durations. The purpose is to provide a method to analyze the sequencing of mining production processes and predict the effect of any planned changes. The simulation is demonstrated through realistic examples, such as longwall face-to-face transfer sequencing and the effect of varying advance rates on longwall development sections. Statistical data, to make more informed production decisions, are generated in the form of project activity/path criticality and project duration distributions.

Jan 1, 1995

By D. Wenstrup, K. Perry, J. Hatfield, P. Sainato, B. Lusk

Concrete-infused cloth is used in several civil and mining surface applications whose circumstances are similar to some of those in underground mining. A feature of this material is that it cannot be overhydrated. In underground conditions, however, the excess supply of water to the cloth for hydration could lead to muddy and potentially unsafe working conditions, as well as resource wastage by supplying more water to the construction site than is needed. The objective of this study is to verify the water-to-cloth ratio and study the effect of hydration level on the strength of the Concrete Cloth product. We found that the strength increases with increased hydration up to a 1:2 water-to-cloth ratio by weight, after which the strength holds steady regardless of additional hydration. This confirms the 1:2 water-tocloth ratio by weight for hydration and confirms that strength is retained even if the cloth is excessively hydrated.

Jan 1, 2014

By J. S. Whatley

The properties, origin and industrial uses of kaolin clay are briefly reviewed. The general waterwashed beneficiation process is described. Yost aspects of filtration and solids-liquid separation as practiced in the kaolin industry are mentioned along with devices that are currently in the developmental stage. The paper focuses heavily on the well known art of rotary vacuum filtration, including general construction and operating details. Devices under investigation that might be used to mechanically or electrically dewater clay slurries to higher cake solids levels than can be achieved with rotary vacuum filters are described briefly.

Jan 1, 1986

By Edwin B. Eckel

THIS paper, based on brief field examination and on data supplied by the operators, records the condition of the Italian mercury industry as of March 1945, not long after Italy's collapse. Except for the once-Italian but now Yugoslavian Idria mine near Trieste, virtually all the known mercury deposits are in the Monte Amiata district in Siena and Grosseto Provinces, 75 miles north of Rome. This district contains the Abbadia San Salvatore, the Siele, the Argus, and the Cerreto Piano mines besides numerous prospects and unproductive mines. Under pressure from Germany the principal mines were highly productive during the early part of the war, but production fell off long before its end. All of the mines were damaged in some way at the German withdrawal but by September 1944 the Abbadia had resumed production and several others were only lacking power by the early spring of 1945. The Monte Amiata district is characterized geologically by a thick series of sedimentary rocks that range from Triassic to Eocene in age and are surmounted on Monte Amiata itself by a thick cap of extrusive trachyte. Bodies of travertine and of landslide detritus, younger than the trachyte, are rather widespread. The structure is complex and little known but most of the ore deposits seem to lie along or near a major, north-trending fault or on associated cross-fractures. Cinnabar is the only important ore mineral and clay minerals are by far the most abundant products of hydrothermal alteration. A southward increase in the amount of stibnite, relative to cinnabar, suggests horizontal zoning. The grade of ore ranges from 0.60 to 3.0 pct and the reserves, as compared with those in American mines, are enormous. Even in the face of war-time scarcities, the mines are remarkably self-sufficient and labor is plentiful, but the costs of production are estimated to be not greatly below those of the better American mines. Notes on the principal mines, on the mining and metallurgical methods, and on the manufacture of synthetic cinnabar are included in the paper.

Jan 1, 1947

By David Chadwick, Paul Marsden, Chris Hughes, Mathias Delapille

"Following damage caused by the 2011 Christchurch earthquakes, the NZ$127.5million Christchurch Town Hall Restoration project is due for completion in 2018. The building is undergoing extensive repairs and a strengthening regime to meet New Zealand’s New Building Standard. One major aspect of the project is the stabilisation of the soil directly beneath the building using interconnected jetgrouting columns installed a cellular configuration, the purpose of this being to decrease the likelihood and severity of foundation movements caused by earthquake-induced soil liquefaction and lateral spreading. The soils encountered on the site ranged from cobbles and gravels through to sandy silts with a significant quantity of timber and rootlets. This wide variation of soil types presented a number of challenges with regard to effective and consistent treatment by jet grouting. The paper presents an overview of the quality assurance practices and also the testing regime adopted on this project.INTRODUCTIONMost of the deformation experienced by the Christchurch Town Hall structure over the course of the Canterbury earthquakes was caused by movement of the underlying ground. Two primary mechanisms of ground deformation were observed:- Liquefaction of the soils underlying the building foundation- Lateral spread of surface soils towards the free face at the river edge which runs 20 metres from the building. This mechanism also resulted in additional vertical settlement of the building foundations.The overall foundation design philosophy adopted by the project team for the Christchurch Town Hall Conservation Project has been to improve the ground directly beneath the structure to mitigate against these two mechanisms of ground movement. Additionally, a robust raft slab is proposed to distribute the foundation loading more evenly and increase the ability of the structure to resist lateral stretch of the underlying ground.The ground improvement system proposed by the Client’s geotechnical consultants, Tonkin &Taylor, comprised a cellular arrangement of interlocking jet grout columns, this arrangement would effectively encapsulate the soil within the cells preventing lateral spread.In total 1,097 interlocking jet grout columns, extending over the entire floor plan of the structure, were required to satisfy the design requirements."

Jan 1, 1900

By Vladimir G. Kochnev

Crushing and grinding account for the major portion (60 to 80 percent) of the overall expenses for ore processing. Autogenous (AG) and semiautogenous grinding (SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills (Bassarear, 1982, MacPherson, 1989, Pithois, Casalis, 1983, Maripuu et al., 1983). However, there remains room for improvement to existing AG and SAG technologies and both technologies have immense economic benefit potential. Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that grinding in AG and SAG mills can be performed in a more effective way. The company's approach comprises the following elements: ? Novel mill design. ? New liners and lifters. ? Novel discharge grid design. ? Technique of treating material of critical particle size. Comparative tests that demonstrated the usefulness of these innovations are described in this article. Currently, there are hundreds of AG and SAG mills in operation throughout the world. Application of new internal elements of the mills and reconsideration of the circuit design of the existing grinding equipment using present technological solutions would significantly increase the throughput rate and diminish power requirement.

Jan 1, 2008

The need for an integrated approach to optimization of unit operations in both the pit and the mill has long been recognized, but the complexity and nature of the overall problem has up to now resisted solution. This paper reports on a modeling methodology which couples symbolic and numeric computing to unify operations in both the pit and mill. The ultimate goal of this work is to optimize all operations that are influenced by blasting. Blasting plays a key role in all facets of operations. Obviously, drilling and blasting costs are determined by blast design, but the down-stream costs that are closely related to blasting results are often treated as separate functions: loading, hauling, cleanup, and crushing and grinding are all heavily influenced. Diggablilty and bucket fill factor are a function of fragmentation, the condition of the floor and uniformity in the shape of the muck pile. Likewise, cycle times and loading delays partially determine haul cycles, while fragmentation distribution and size determines the efficiency of truck loading. Removal and breakage of oversize causes loading delays and increases cleanup costs. The influence of blasting doesn't stop at the crusher. Mill productivity, power consumption, and maintenance are a function of the feed. Even at the SAG mill a reduction of a critical particle size during blasting can increase throughput. Thus, a bottle-neck for production far removed from unit operations in the pit can be alleviated by a modification in blast design. The question is: how do we optimize blasting with respect not only to itself but to al\ related mining and milling operations? For that matter, how do we even model blasting so that we can control the results of a blast?

Jan 1, 1991

By Leo Panian

Over the last decade, drilled and post-grouted micropile foundations have come to be increasingly relied upon for resisting seismic loads in building foundations on the West Coast. Micropiles have been successfully deployed in a range of soil conditions, in vertical as well as battered configurations, to support a variety of structural systems difficult soils. Their high load capacity in tension as well as in compression, their ability to be installed in confined spaces with minimal overhead clearance, and their ability to be directly tested in an installation have made them indispensable for seismic strengthening of existing structures. More recently, growing industry experience along with improvements in design guidelines have led to wider acceptance of micropiles among engineers and building officials. The increasing availability of the specialized materials, coupled with growing familiarity with drilling technologies among design-build contractors has made micropiles more cost-effective and competitive. For the first time, micropiles are finding applications in the construction of new buildings, where they are combined with shallow footings in hybrid foundations to efficiently resist seismic loads. These new applications rely on more intensive engineering analyses to evaluate the performance of micropile foundation systems and develop detailed requirements for design and construction. This paper describes the design approaches and the analytical methods for the seismic design of hybrid micropile foundations, and provides examples of recent construction projects that demonstrate the application.

Jan 1, 2010

By H. C. Rickaby

BY August 1944 Canada expects to be shipping 56 percent hematite ore from its new Steep Rock iron mine, via Port Arthur on Lake Superior, to the steelmaking centers in Canada and the United States. This is indeed welcome news to steel men, especially if they operate open hearth furnaces, as the Steep Rock ore is a high-grade lump and will be valuable as charge and feed ore. But better news is the fact that this first big producer of high-grade hematite ore in Canada, since the exhaustion of the Helen mine in the Michipicoten area north of Lake Superior in 1918, has a proved ore body of 16,757,000 long tons and a probable ore body of 14,000,000 long tons, thus giving an over-all total of 30,757,000 long tons and assuring production for a number of years to come.

Jan 1, 1943

By E. Y. Baafi, H. Fan, W. Zeng

We present a discrete event simulator, TSJSim (Truck-Shovel JaamSim Simulator), for evaluating the stochastic and dynamic operational variables in a truck-shovel system. TSJSim offers four truck allocation strategies: Fixed truck assignment (FTA), Minimizing shovel production requirement (MSPR), Minimizing truck waiting time (MTWT), and Minimizing truck semi-cycle time (MTSCT) including the genetic algorithm (GA) optimization and the frozen dispatching algorithm (FDA) optimization rules. Multiple decision points along the haul routes for all the trucks close to the decision points were included in the model. The simulation results indicate that the trends associated with production tons and queuing time utilizing the four truck allocation strategies (MSPR, MTWT, FDA, and GA) all demonstrated similar patterns as the fleet size varied. As the system fleet size increased, the system production tons under these strategies at first increased significantly and then remained relatively constant; the queuing time relating to these strategies showed a positive relationship with the system fleet size. The bunching time decreased when the truck allocation strategies were applied in the model. In the simulated truck-shovel network system with multiple traffic intersections, by assigning the trucks at the intersections, both productivity and fleet utilization increased.

Dec 13, 2022

By John Chadwick

In the drive for faster development advance rates, railbound systems can be advantageous, in the right application. Skanska BS, the contractor to mine-owner VSK Mining, is driving an adit access deep into the Volouské Urchy Mountain in Slovakia to access the Gemerská Poloma talc deposit, some 70 km (43 miles) west of Ko?ice, the economic and cultural center of eastern Slovakia. Skanska began driving the Stolna Elisabeth drift in February 2007, extending 25 kg/m (50 lb/yd) rails (with 750 mm or 30 in. between sleepers) into the mountain to provide the main haulage to bring talc ore and waste out of the new mine once it gets into production. It will also be used for personnel transport, and is now almost complete. As a second egress and for ventilation, a 2.5-m- (8.2-ft-) diameter shaft of about 300-m (984-ft) depth will be sunk from surface down into the orebody. Stolna Elisabeth is a 4.2-km- (2.6-mile-) long drift mined at a cross section of some 11 m2 (118 sq ft). The finished profile is 3.2-m- (10.5-ft-) wide by 3.6-m- (11.8-ft-) high. It has been developed on a very slight incline so that water runs down it to the portal. The portal is 450 m (1,476 ft) above sea level and the end of the tunnel is 475 m (1,558 ft) above sea level. Much of the rock through which it has been developed is magnesite with a compressive strength of 150 MPA. The drilling jumbo is an Atlas Copco twin-boom Boomer 282 Raildrill drilling 42- to 45-mm- (1.6- to 1.7-in.-) diameter holes to a maximum length of 2.5 m (8.2 ft), depending on ground conditions. This is a drill jumbo that Skanska has used successfully on a number of projects during its life. The condition of the rock through which this drift has been driven is extremely variable. Five classifications of A1 and A2 and B1, B2 and [ ] B3, where A1 is the most competent rock and B3 is the worst, have been established. The amount of support used, of which more later is determined by the classification of ground conditions. At the time of the author?s visit, the project it was about 40 days ahead of schedule, thanks to high advance rates. For instance 6 m/day (20 ft/d) was the plan for the advance to be achieved in B1 rock, but sometimes the crews have achieved 8 m/day (26 ft/d) ? which is the average for the whole project ? in those conditions. In A1 the best advance rate achieved is 12 m/day (39 ft/d). The loading unit is a Häggloader 9HR-B on crawler tracks with a pony track to run on the rails. This allows the unit to be towed up and down the drift along the rails. To load from the face, the Häggloader lowers the foot of its onboard conveyor system to the floor and the backhoe pushes material on to it. This digging arm-conveyor combination produces uninterrupted, optimal volume loading of the haulage unit, without spill ? a technique offering load capacities as high as 180 m3/h (6,356 cu ft/hour). Further-more, as an electrically powered machine, it offers great

Jan 1, 2009

By Albert L. Toenges

COAL mining technique progressed slowly until the advent of mechanized mining. The cutting machine was a forward step, but had only a limited effect upon improving the percentage of coal recovery. Previously, the physical fitness of the loaders and the total output of the miners fixed mine production. The miner was an independent contractor and supervision over his working place was superficial. Rising costs and the inroads of substitute fuels demanded increased output per man to lower the unit production cost. Therefore, the amount of coal loaded mechanically in underground bituminous mines has risen from 0.3 per-cent in 1923 to 7.4 in 1929, to 20.2 in 1937, and to 48.9 percent in 1943. When loading devices were introduced it became necessary to adapt them to existing systems of mining, or to alter the mining system to fit the machine. An increased amount of supervision was required as output depended upon proper operation of the machine rather than on the physical fitness of the individual.

Jan 1, 1946

The discovery of magmatic nickel sulfide mineralisation within the Musgrave Block of Central Australia, in a region which has received virtually no exploration since the early 1970s, promoted a pegging rush throughout the region and provided a significant boost to the investor interest in resources sector companies. The discovery proved a significant success for the application of generic models for major magmatic nickel-copper sulfide deposits. The entry of junior explorers to the region is the principal mechanism by which the region will be explored, although significant social and physical challenges will impact on the ability of explorers to maintain investor confidence in the region.

Jan 1, 2002