Search Documents

By Robert Warner

WHEN a new mine is opened, and often when an operating mine must adapt itself to physical or economic changes, a mining system must be selected in complete detail. In the past the plan chosen was usually the product of the local staff alone, however limited the training and experi-ence of that staff might be, which often resulted in the introduction of methods that were familiar to the staff, but not so well suited to the con-ditions as others unknown to the local men. A new management, noting the difficulties with the existing layout, might make modifications or complete changes, so that many mines in their history have seen a whole series of mining systems, each somewhat laboriously grafted on to its predecessor. This should not be interpreted as a condemnation of the older staffs for sticking to the tried systems, such as open square-sets in the early days at the Homestake, because they knew it would work after a fashion, nor does the statement apply to the technically trained, and usually broadly experienced staffs of most present-day properties. The older miners did not have the variety of tools and methods, nor the present freedom of transfer of information as to what the other man is doing, and so did the best they could under the circumstances. Finally, the higher grade of the ores made the choice less vital. The ever-increasing need to mine low-grade orebodies, with a fixed or even lower price for the metal produced, has caused an increasing need for low-cost mining. In most new mines this has simplified the problem of selection by eliminating from consideration all of the high-cost systems, but it has also complicated the choice by the necessity for refinement in detail and a close adjustment of the plan selected to all the conditions at the property. In these low-cost problems any textbook division of mining systems as applied to "beds, veins or masses" avails little as a guide. It should be realized at the outset that to' be successful under modern competitive conditions a system of mining must be worked out with elaborate detail, with careful time scheduling and control of the various elemental operations, and that after it is introduced it must be run with a large amount of technical direction.

Jan 1, 1933

By D. Harrington

An explosive may be defined as a substance (usually a mixture) that has the property of yielding, readily to combustion or oxidation upon application of flame or shock, the combustion or oxidation process being rapid and accompanied by formation of such relatively large quantities of gases that much violence and pressure are produced; these, in turn, react against their surroundings and cause what is termed an explosion. By their very nature their action is destructive and disruptive of adjunct materials; hence, all explosives axe potentially hazardous and every type of explosive, irrespective of its relative safety, should be handled, .stored, and used with utmost care at all times and under all conditions. It should always be remembered that any explosive can be rude safe only in certain of its features and under certain conditions and circumstance. If these facts (and they certainly are facts) are always kept in mind, most of the modern types of explosives can be utilized advantageously in our industrial life and with a considerable degree of safety. That commercial explosives can be handled. safely is borne out in part by the fact that in the past 15 years at least 3,000,000,000 pounds of the commercial explosive dynamite have been transported by railroads in the United State, without injury to any person, insofar as available records indicate.

Jan 1, 1939

Allen & Garcia American Mining Congress American Steel and Wire Company Blue Blaze Coal Company Bogue Supply Company Brandenberger, L. Burke Company, J. J

Jan 1, 1929

By Boryong Lee, Heedong Sung, Minho Park, Sunyoung Choi

Recently, the demand for ultra-thin steel plate with high hardness and strength has been increasing in various industries. In order to satisfy this requirement, steel company designs the chemistry with low CEQ and obtains the required characteristics through quenching and tempering process. Especially, these steels are accompanied by low temperature tempering as a necessary process. Unlike ordinary high temperature tempering steels, it is impossible to improve the flatness after low temperature tempering. Therefore, shape control in the quenching process is very important for securing the excellent quality flatness. In order to obtain flatness in the quenching process, uniform cooling inside the plate should be accompanied. However, the quenching process has limitations in estimating the temperature behavior during cooling because the plate temperature is lowered to room temperature. In this study, a thermocouple was installed inside the actual quenching plate to measure the temperature behavior during cooling and to establish the manufacturing conditions of the quenching plate to ensure excellent flatness quality.

Oct 1, 2019

By Lachezar Tsotsorkov

Being a mining company, Assarel-Medet has a significant impact upon the environmental components. In order to meet the legal requirements and the requirements stipulated by the effective permits as well as to reduce the environmental imprint throughout the years, the policy of the company to implement a number of projects to improve the environmental components quality and the environmental state in the company?s region. The projects associated with atmospheric air quality management and reduction of the impact exercised by Assarel-Medet JSC by implementing various measures to eliminate the potential sources of the impact, preventive and rehabilitation initiatives as well as organizational and administrative activities are among the most important ones. A stable improvement of atmospheric air quality in the region and minimization of the company impact upon the ground air state in the region was observed in the period from 2005 to 2012 due to the applied measures. This project is a contribution to the environmental protection, in particular to atmospheric air protection, by applying integral monitoring and modeling methods to identify the negative impact by the mining companies and plan measures to reduce and restrict it as well as to improve the quality of the environment and living area of people working and living in the impact range as an element of sustainable development.

Aug 1, 2013

By Fathi Habashi

The recovery of uranium from wet process phosphoric acid was applied on industrial scale in the 1940's by using octylpyrophosphoric acid as an extractant. Later, more efficient reagents were used, e.g., di(2-ethylhexyl) phosphoric acid and actylphenyl phosphoric acid. In the 1970's the rare earths in Kola phosphate were recovered in Finland and recently (1997) in Norway using HNO, as a leaching agent and di(2-ethylhexyl) phosphoric acid as solvent. It was demonstrated later on laboratory scale that both uranium and rare earths could be extracted from the rock by tributyl phosphate but at different pH values provided that the rock is leached with nitric or hydrochloric acids instead of the commonly used sulfuric. This new concept opens the way to the possibility of treating phosphate rock by in-situ, dump, or vat leaching for the recovery of phosphate values as well as uranium and the rare earths. Another solvent extraction process is used industrially for the purification of phosphoric acid using butyl and amyl alcohols.

Jan 1, 1998

By Anthony Edey

It is a generally accepted and widely discussed fact that the world in general, and the United States in particular, face a shortage of energy at the present time which will become worse in the future. There is, however, no sign of a similar concensus as to the actions which would prevent or overcome this expected shortage. An immense variety of solutions has, however, been put forward, ranging from the purely political to the outer fringes of sophisticated technology. One resource which surprisingly is often only cursorily included in this discussion is the immense known petroleum reserve lying within the United States. When this subject is discussed, indeed, it is usually in the context of the improvements in production or new discovery rate that could be expected to result from possible politico-economic actions that would raise the real price obtained for domestic crude. This interest in the potential for improved domestic production is undoubtedly justified, but very little attention is normally drawn to the fact that even under the most favorable policy framework the majority of the oil that has been, or will be, discovered will remain in the ground due to the inherent limitations of production through surface wells.

Jan 1, 1979

By R. D. Springer, R. L. Wilcox, P. A. PALMARTAN, R. K. Waring, E. A. Anderson

A knowledge of the mutual liquid solubility of zinc and lead is of importance in various phases of zinc metallurgy. The determination of this solubility has been the subject of numerous investigations, but unfortunately the results vary widely, particularly at higher temperatures, and it has been impossible to decide what data are most reliable. It was decided to investigate the matter and in view of the disagreement in the published results, it was felt necessary to take rather unusual precautions to insure the reliability of the data. For this reason determinations were made by four different methods, and the procedures of several of the previous investigators were duplicated. The previously used methods can be divided into two classes: methods involving freezing the entire melt and taking samples of the lead-rich and zine-rich phases in the solid state,l,2 and methods in which the samples are taken while the bath is liquid and at the desired temperature.3,4 Data obtained by methods involving freezing the entire melt show much lower solubility of lead in zinc than methods in which the liquid is sampled at temperature. The latter method was used by Spring and Romanoff5 and by Hass and Jellinek.6 The results of these two investigations are in agreement at temperatures near the melting point but at higher temperatures Hass and Jellinek find a higher mutual solubility. The low-temperature section of the zinc-lead equilibrium diagram is given by Peirce and Anderson.7 The diagram is based on the data of Hodge and Heyer,8 Arnemann,9 and Peirce.10

Jan 1, 1934

By Chester O. Ensign

Many publications to date have advocated under- seas mining operations, optimistically overlooking the paucity of information on mineral distribution and the ocean environments in which minerals occur. Such articles (smattered with opinion, as is this article) are herein tempered by my more conservative views on the economics of mining under the seas. For purposes of this paper, underseas mining refers only to the deeper surficial deposits of the continental shelf and the deep sea floor, i.e., the deposits of phosphorite and manganese nodules.

Jan 9, 1966

Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years and both the operators and their employees are deserving of much credit for the efforts put forth to better living, working, educational and receational conditions in most of the mining camps of the state. In the older metal mining camps of Utah, where the towns are incorporated and independent of the mining properties operating in the vicinity, less opportunity is presented for the companies to exercise efforts looking towards improved welfare conditions than is the case of camps located on company ground and under the full control of operators.

Jan 1, 1925

BUMPS in No. 2 Mine, Springhill, N. S., furnished the main feature for discussion at the morning meeting* on Ground Movement and Subsidence on Feb. 18. Walter Herd, the author of the paper by which the discussion was introduced, not being well, was unable to be present. The paper was presented by T. L. McCall, who laid stress on the presence of sand- stone as the cause of bumps, on the value of retreating longwall in eliminating such phenomena at the coal face and on the advantage of wide headings with packs on either side, leaving space behind them for any coal that bumps might dislodge. George S. Rice, who presided, referred to his visits to the Nova Scotia mines and said that bumps usually occurred only where the coal was thick and strong and the roof and floor both more than usually hard. If any of the three were weak, bumps were not likely to occur. In the Nova Scotia mine, to which Mr. Herd referred, there was no material for packwalls and for this reason as well as for safety he had been convinced that long- wall retreating with a small percentage of pack walling was the most feasible plan.

Jan 1, 1929

By C. Garcia, A. Potulska, J. J. Opazo, T. Comi

"The Sierra Gorda SCM sulfide ore processing plant began commissioning in the third quarter of 2014. Located in the Atacama Desert in northern Chile, the project is an open pit mine and Copper-Molybdenum processing plant is one of the most highly-instrumented operations in the world. It is the first hard rock operation in Chile and the second in South America to utilize HPGR technology. It is a significant Molybdenum resource especially in the first five years and the Molybdenum separation plant is complex. Designed to process up to 60 million lbs. of fine Molybdenum per year, it uses the latest technology and equipment to ensure superior recovery and product quality. It also has gas handling and alarm systems to fulfil the Company’s vision of “Zero Harm”. This paper discusses the overall operation and issues relating to the concentrator start-up. These include a review of the mineral processing design, the unified process control center and management information systems, and the correlation of geological and metallurgical performance data (mine-to-mill) for use in anticipating and preparing for treatment of diverse ore deliveries. INTRODUCTION Sierra Gorda SCM is a joint venture partnership with KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining, and Sumitomo Corporation (Japan) operating in northern Chile. The Sierra Gorda open pit mine and Copper-Molybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, well-instrumented mine in Chile. This paper contains a general review of the project including geology and history. This was a very fast-track project going from greenfield site acquisition to mill start-up in 10 years. Highly-experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied. The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (see Figure 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km from the village of Sierra Gorda at an elevation of approximately 1,700 m above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic, and Escondida, to name a few."

Jan 1, 2015

By Robert Cluff

The Campo Morado precious-metal-bearing, volcanogenic massive sulphide district occurs in a Lower Cretaceous felsic volcanic sequence in a northerly trending belt in the Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. The deposits belong to a low-sulfidation, volcanogenic massive sulphide system formed in a subaqueous environment, and are of the siliciclastic type. Most are on the flanks of felsic domes or in adjacent basins and many are associated with heterolithic volcaniclastic rocks. The Reforma and possibly the El Rey massive sulphide deposits are interpreted to be overturned, and the Naranjo, El Largo, and Estrella de Oro deposits and the El Profundo occurrence to the south are upright. The G9 deposit and the La Lucha and San Rafael occurrences are in an over-thrust plate further to the southwest. In several of the deposits, zinc, lead, silver, and gold are concentrated near the stratigraphic top, and copper is concentrated near the stratigraphic base; copper also is concentrated in replacement bodies near the top of some domes. Major minerals are pyrite, quartz, ankerite, sphalerite, chalcopyrite, and galena. Gold and silver occur in argentian gold, and silver also occurs in tennantite/freibergite and galena. Underlying stockwork zones contain disseminated and vein quartz, pyrite, chlorite, and ankerite, with locally abundant chalcopyrite and/or sphalerite. Exploration since 2004 has enlarged greatly the El Largo and the high-grade G-9 deposits, and slightly enlarged the El Rey deposit. The cumulative in situ massive sulphides for the Reforma, Naranjo, El Rey, El Largo, and G9 deposits exceed 45 Mt.

May 1, 2006

By K. E. Waters, M. Mirnezami, R. Gauvin, A. Jordens, K. W. Malas

"There is currently very little information on the physico-chemical properties of rare earth elementbearing minerals, or on their processing. With the increasing demand for rare earths, this is something that needs to be addressed. This paper introduces some surface chemistry analysis of fergusonite (YNbO4), and the bubble-particle attachment. Zeta potential measurements indicate adsorption of sodium oleate and, to a lesser degree, potassium amyl xanthate onto the surface, and an increase in attachment to an air bubble is observed at pH 4.5 and 6.5. At a pH of 10.5, no attachment is observed, whether in the presence of the reagents or not. This analysis, although initial, will be used to initiate flotation tests, in order to facilitate the selective recovery of fergusonite. INTRODUCTIONRare earth elements (REE) are increasingly in demand, due to their prevalence in both renewable energy devices and high-end electronics. An article in the New Scientist highlighted the importance of a number of REE, many of which most people are be unlikely to have heard mentioned (Crow, 2011). From batteries (lanthanum and cerium) to magnets (dysprosium and neodymium) and lighting (yttrium), the REE are crucial to the advancement of technology and energy saving devices. For example, neodymium is finding most use in the high end magnets that keep the motors turning that power wind turbines and electric cars. In the case of yttrium, the demand outstripped the supply in 2010, emphasising the need to develop deposits containing this and other REE (Crow, 2011). The impact of our dependency on REE has become even more apparent with the reduction in exports by China, which currently controls 97 % of the world’s rare earth production (Pitts, 2011).With the increasing demand for rare earth elements (REE), there is a drive to exploit the known resources around the world. However, the physical beneficiation of the rare earth element bearing minerals is a subject which will require a great deal of investigation to fill the knowledge gaps surrounding these developing rare earth projects. There are numerous articles on REE mineralogy as well as the hydrometallurgical processing of REE concentrates (Alex, Suri, & Gupta, 1998; Peter Gromet & Silver, 1983; Ring et al., 1993; Schnetzler & Philpotts, 1970; Uda, 2000), however a common feature amongst these resources is the lack of detailed descriptions of the physical beneficiation processes required to concentrate REE-bearing minerals. There is work being conducted into reagents and methods for use in recovering some rare earths from their associated ores (Bulatovic, 2010; Ni, Parrent, Cao, & Liu, 2011), but much more in-depth research is required."

Jan 1, 2012

By Edward Steidle

IT has been said that "the command of nature has been put into the hands of man before he knows how to command himself," and what we see about us gives particular emphasis to this observation. If this condition be granted, the vaunted boast of school and college, of the institution that had the training of this generation, and of its fathers, and of its grandfathers, the boast that education is a "preparation for life," stands exposed as a hollow claim, or as a ghastly, cynical conception of life, or else education has fallen far short of its intentions. It has been evident for some time that education was not meeting the fullest expectations of society. In recent years there has been a deal of speculation indulged in by both laity and faculty in regard to American education and American civilization, and some few and sporadic changes have been effected. Today, however, there is no longer time for mere hypothetical considerations; we are faced with certain definite facts and confronted with obvious conditions that will not wait for fine-spun theories. If educators do not put their house in order, someone else will do it for them. The trends in mineral industries education must be in harmony with this general realignment that is today visible on the educational horizon, and only as these trends are in conformity with this movement can they be called sound. Two questions, then, confront mineral industries educators: (1) What are the trends in mineral industries education, and (2) how do these trends correlate with the major educational movements of the day?

Jan 1, 1933

By Juan B. Yianatos

"After almost 100 years, since the first commercial application began in Australia, flotation has shown an extraordinary growth and nearly 2 billion tons of ore per year are presently treated by flotation processes. During this time flotation has promoted a wide scope of research activities ranging from fundamental chemistry and hydrodynamic studies to studies of industrial operations. In general, fundamental studies have been mainly related to ideal situations. In recent years, however, large efforts have been focusing on achieving a better insight into the actual sub-processes provided by the development of new and more sophisticated instrumentation. Since the massive incorporation of flotation columns, around 15 years ago, a renewed interest in flotation fundamental studies, process modelling and new cell designs have been observed worldwide. The key role of the froth has been recognized as an independent and sometimes rate limiting process step. Thus, separation of pulp and froth process stages seems the most appropriate in terms of process modelling, diagnostic, design and scale-up purposes.In relation to flotation equipment development, until the middle of the 1970’s, only the sub-aeration mechanical cells were dominant. Since the 1980’s, the use of pneumatic cells and forced air mechanical cells has emerged strongly. Also, in the last decade, flotation equipment has shown a dramatic increase in size, reaching values of 200m3 in unitary mechanical cells and more than 300m3 in columns. The general feeling, however, is that, despite the great advance observed in terms of process knowledge, the mechanisms and principles of industrial flotation cells design and scale-up are still not fully understood.Advances in process instrumentation and control now in use allow for more efficient operations, both in metallurgical performance and savings in operating costs."

Jan 1, 2003

By K. M. Wild, C. D. Martin, F. Amann

"Argillaceous rock formations, in particular clay shales, are notorious for creating challenges in rock engineering. Due to their generally low hydraulic conductivity and their complete saturation in their natural state at depth, the behavior of clay shales is usually characterized by a strong hydro-mechanical coupling.This paper presents typical pore pressure responses monitored in different underground rock laboratories and explores alternative ways for their interpretation. The underpinning processes and their relevance are identified based on analytical and conceptual numerical models. Pore pressure monitoring data from Opalinus clay at the Mont Terri Underground laboratory, the Boom Clay at the Mol facility and the Callovo-Oxfordian clay in the Meuse/Haute–Marne URL show a similar pore-pressure response associated with stress changes accompanying tunnel construction although the tunnels were built in different rock types, at different locations, and under different in-situ conditions.The numerical analyses in this study shows that the pore pressure response around an excavation in low permeable clay shales may have different explanations. Pore pressure drops observed in the tunnel near field can theoretically be explained by both, a pure elastic response in an isotropic or anisotropic rock mass with an anisotropic stress state, or a inelastic response and related dilatancy. However, a comparison between the numerical models and the in-situ measurements revealed that the latter is more likely. This conclusion is justified by the observation that pore pressure drops occur significantly ahead of the tunnel face which is not the case in elastic numerical simulations. Pore pressure measurements in the far field, where failure processes are unlikely to occur, can only partly be explained by a linear poroelastic models. The introduction of an anisotropic material plays a key role in reproducing the responses, conceptually."

Jan 1, 2015

By V. de Ruiter

In the northwestern part of the Netherlands lies the deepest solution salt mine in the world. The company operating the mine is Frisia Zout bv (part of the K+S group). Extracting the NaCl from caverns at a depth of nearly 3000 m has a lot of challenges. Continuously monitoring, among others, the flows, pressures and salt concentrations is necessary to safely and economically mine the salt. A system has been set up at Frisia to be able to monitor the data from a distance. Data has been put in graphs to monitor the trends daily. All gauges are also continuously monitored to maintain accuracy. With this system a better understanding of the mining process has been made and has led to many optimizations.

Jan 1, 2008

By C M. Stewart

Lithium battery electric powered vehicles and machines (BEVs) continue to gain traction inunderground mining use, with predictions they will dominate the underground light and heavy vehicle fleets for some mines within the next decade. There are clear advantages for ventilation systems through reduced heat output and the elimination of harmful exhaust gases and diesel particulates. However, the risks and effects of BEV fire emergencies for underground personnel and ventilationsystems are still largely in the early stages of analysis and understanding. This paper conducts an industry review of a selection of lithium battery fire incidents and research.A research paper review on lihthium fire behaviour, intensity and toxicity will be analysed and comparisons made with equivalent diesel machinery fires for context. Guidelines for mine firemodelling parameters will be offered to assist in predicting the behaviour, heat and emissions from BEV fires, and recommendations and conclusions will be drawn on the specific hazards of lithium battery fires compared to conventional diesel powered machines.

Oct 12, 2022

By Terry D. Vandell

The purposes of this presentation are: (1) to discuss the actual as well as potential incidents that have caused and that could cause groundwater contamination at uranium in situ leach mining sites and (2) to discuss remedial actions and solutions that have been or that could be implemented in the future to stop or prevent serious groundwater contamination from in situ leach mining in Wyoming?s Powder River Basin. Open pit, underground, and existing and proposed in situ leach uranium mine sites in the Powder River Basin are shown in Figure 1. In situ leach mining or solution mining for extracting minerals in liquid form is a relatively new addition to the list of conventional mining methods currently used to extract uranium in Wyoming's Powder River Basin. Basically, the in situ leach mining method involves: (1) the injection of a leach solution lixiviant (an acidic or basic oxidizing solution) into a uranium-bearing ore body, via injection wells, to complex the contained uranium, (2) mobilization of the uranium complex from the host material via creation of a soluble complex salt, and (3) surface recovery of the solution bearing the uranium complex via production wells. Uranium is then separated from the leach solution by conventional milling unit operations (ion exchange).

Jan 1, 1981